Search NASA⌕ Search

SEARCH · Search NASA

Results for “cell balancing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Re-Engineering Poly(Acrylic Acid) Binder toward Optimized Electrochemical Performance for Silicon Lithium-Ion Batteries: Branching Architecture Leads to Balanced Properties of Polymeric Binders

Silicon is a promising anode material for lithium-ion batteries with its superior capacity. However, the drastic volume changes during lithiation/delithiation cycles hinder the cycling performance, resulting in particle pulverization, conductivity loss, and an unstable electrode-electrolyte interface. In this work, a series of synthetic polymeric binders, poly(acrylic acid-co-tetra(ethylene glycol) diacrylate)-featuring a poly(acrylic acid) (PAA) backbone branched via tetra(ethylene glycol) diacrylate (TEGDA)-are developed that edge toward evidencing well-balanced properties to confront capacity fading in Si-based electrodes. The incorporation of ether chain not only leads to the branching architecture of the PAA backbone, thus affecting its mechanical properties, but also promotes the conductivity of Li ions. As a result, a synergistic performance improvement is observed in both half and full cells. The best-performing cell using a branched PAA binder (bPAA) with a feeding molar ratio ([TEGDA]:[acrylic acid(AA)]) of 0.2 results in a 10% increase in initial capacity and a 31% increase in capacity retention over 100 cycles compared to the linear PAA cell. The cross-sectional microscopic images of the cycled electrodes reveal that bPAA binders can drastically reduce the electrode expansion. This improvement results from the well-balanced properties of the polymer design, which could guide further development for more advanced binder materials.

25 ENERGY STORAGE↗
DOE OSTI2024

Development of Stable Solid Oxide Electrolysis Cells for Low-Cost Hydrogen Production

The project objective was to demonstrate a solid oxide cell-based steam electrolysis stack that exhibits robustness, reliability, endurance, hydrogen purity, and produces hydrogen at elevated pressure of 2 to 3 bar. Innovative materials and processing methods were evaluated to improve degradation characteristics. Performance improvement focused on nearly all layers involved in the cell and stack assembly. Primary attention was paid to zirconia-ceria interface resistance control via sintering optimization and decrease in degradation from the oxygen electrode by evaluating low strontium (Sr) or Sr-free composition for both the oxygen electrode and current collection layer. Stack robustness was addressed by validating redox tolerance of fuel electrode, confirming capability of cells to survive repeated thermal cycles, studying the effect of pressure on performance and degradation, evaluating the effect of contamination on fuel and oxygen electrode performance and degradation, and identifying mitigation strategies to improve performance. The characterization included evaluation of electrochemical performance and stability followed by microstructural analysis. At the cell level, performance and stability improvements were achieved by incorporating a Sr-free oxygen electrode and a denser oxygen electrode barrier layer. At the stack level, pressurized operation reduces demand on first stage compression, the redox tolerant fuel electrode mitigates risk from service interruptions, and improvements to interconnect coating alleviate chromium (Cr) contamination effects. The denser barrier layer was achieved by adding a sintering aid to the samaria-doped ceria (SDC) composition that reduced sintering temperature by 150 °C. The resulting density was on par with the baseline SDC barrier layer density and the lower sintering temperature resulted in less resistive phase formation during sintering. Button cell tests did not demonstrate a change in performance when exposed to silicon (Si) or manganese (Mn) impurities to the fuel electrode and Cr impurity to the oxygen electrode. More detailed study however is warranted. The project addressed SOEC performance and stability at the cell and stack levels through a systematic approach to known sources of degradation that were combined and tested in three stack tests using an electrolyte supported cell design to allow for evaluation of a variety of fuel and oxygen electrode compositions. STK-82 and STK-83 had identical compositions. STK-100 incorporated the best materials and processing variables developed under this and concurrent projects, and was tested at elevated pressure in steam electrolysis. • STK-82 recovered performance after redox and thermal cycling, demonstrating the robustness of the stack and seals. It exhibited stable performance in testing for 500 hours in SOEC mode, followed by 300 hours of cycling between SOEC and SOFC tests. Degradation during SOEC operation was 1.8 %/ 1,000 hours. • STK-83 generated hydrogen at >80% steam conversion, and oxygen above 98.5 % purity during pressurized operation. Both hydrogen and oxygen were generated at 3 barg pressure without the use of a pressure vessel. In addition to balanced pressure, electrolysis operation at 1 bar differential pressure across anode and cathode was also demonstrated to substantial the robustness of the cell and seal. • STK-100 measured at initial ambient pressure conditions showed an area specific resistance of 1.1 ohm-cm 2 , and STK-83 had 1.3 ohm-cm 2 .

08 HYDROGEN↗
DOE OSTI2021

Methodologies for Design, Characterization and Testing of Electrolytes that Enable Extreme Fast Charging of Lithium-ion Cells

Selection, testing and validation of electrolyte candidates for Li-ion cells are discussed, based on a 10-minute target for extreme fast charge (XFC). A combination of modeling and laboratory measurements create a timely and synergistic approach to identifying candidate electrolyte formulations. Multi-solvent systems provide a balanced set of properties, wherein lower molecular-weight solvents offer reduced viscosity, increased species diffusivity, and mitigation of concentration polarization at high charge rates. Carefully selected formulations can exhibit peak conductivity and usable conductivity range of two to three times that of the baseline EC-EMC (3:7, wt.) + LiPF 6 . Candidates are also chosen based on stability and longevity within the cell environment. Lab testing coincides with property predictions from the Advanced Electrolyte Model (AEM) and a macro-scale cell model. Furthermore, cell testing utilized coin and pouch cells having NMC532 or NMC811 cathodes with graphite electrodes. Results indicate combinations of low-molecular weight solvents are key for fast-charge electrolytes as they extend the useful conductivity range to both low and higher salt concentrations, and possess higher self-diffusivities compared to conventional solvents. This reduces impacts from concentration polarization. The choice of electrolyte also influences the tendency for lithium metal deposition at the anode, as showcased by experimental and modeling results herein.

25 ENERGY STORAGE↗
DOE OSTI2022

Garnet solid electrolyte blended LiNi 0.6 Mn 0.2 Co 0.2 O 2 as high-voltage stable cathodes for advanced lithium-ion batteries

Ni-rich LiNi 1-x Co x/2 Mn x/2 O 2 layered materials have been widely adopted as cathodes for current electric vehicles (EVs) due to their high gravimetric and volumetric energy densities. However, their high-voltage instability (e.g., > 4.3 V vsLi ) limited their usable capacities corresponding to about 60 – 70 % of theoretical capacities. The major problems of high-voltage operation stem from instability of Ni 3+/4+ at cathode-electrolyte interphase (CEI) in contact with electrolytes. Here we propose garnet-type Li 6.7 La 3 Zr 1.7 Ta 0.3 O 12 (LLZT) solid-electrolyte-blended LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC) as high-voltage stable cathodes. The LLZT not only passivates the CEI but scavenges protons and moisture in electrolytes. From well-balanced ionic and electronic transport properties, 5 wt% LLZT blended NMC cathodes delivered enhanced electrochemical performances in full-cells. Unlike other complicated coating processes, our proposed solid-electrolyte blending approach can be readily implementable in commercial Li-ion batteries due to its manufacturing friendliness, energy saving, and cost effectiveness.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Utilizing the unique charge extraction properties of antimony tin oxide nanoparticles for efficient and stable organic photovoltaics

Simultaneously enhancing device performance and longevity, as well as balancing the requirements on cost, scalability, and simplification of processing, is the goal of interface engineering of organic solar cells (OSCs). In our work, we strategically introduce antimony (Sb 3+ ) cations into an efficient and generic n-type SnO 2 nanoparticles (NPs) host during the scalable flame spray pyrolysis synthesis. Accordingly, a significant switch of conduction property from an n-type character to a p-type character is observed, with a corresponding shift in the work function (WF) from 4.01 ± 0.02 eV for pristine SnO 2 NPs to 5.28 ± 0.02 eV for SnO 2 NPs with 20 mol. % Sb content (ATO). Both pristine SnO 2 and ATO NPs with fine-tuned optoelectronic properties exhibit remarkable charge carrier extraction properties, excellent UV resistance and photo-stability being compatible with various state-of-the-art OSCs systems. The reliable and scalable pristine SnO 2 and ATO NPs processed by doctor-blading in air demand no complex post-treatment. Our work offers a simple but unique approach to accelerate the development of advanced interfacial materials, which could circumvent the major existing interfacial problems in solution-processed OSCs.

14 SOLAR ENERGY↗
DOE OSTI2022

Design Tool for Estimating Adsorbent Hydrogen Storage System Characteristics for Light-Duty Fuel Cell Vehicles

This work combines materials development with hydrogen storage technology advancements to address onboard hydrogen storage challenges in light-duty vehicle applications. These systems are comprised of the vehicle requirements design space, balance of plant requirements, storage system components, and materials engineering culminating in the development of an Adsorbent System Design Tool that serves as a preprocessor to the storage system and vehicle-level models created within the Hydrogen Storage Engineering Center of Excellence. Computational and experimental efforts were integrated to evaluate, design, analyze, and scale potential hydrogen storage systems and their supporting components against the Department of Energy 2020 and Ultimate Technical Targets for Hydrogen Storage Systems for Light Duty Vehicles. Ultimately, the Adsorbent System Design Tool was created to assist material developers in assessing initial design parameters that would be required to estimate the performance of the hydrogen storage system once integrated with the full fuel cell system.

08 HYDROGEN↗
DOE OSTI2026

Conductivity Spectroscopy for Investigation and Discovery of Photovoltaic Materials

Conductivity spectroscopy is an extremely powerful set of methods for probing the properties of optoelectronic materials, especially photovoltaics, where photoconductivity is one of the best spectroscopic proxies for performance. Despite this power, they are substantially less commonly used than time-resolved photoluminescence (for instance) because they tend to be more expensive to implement (THz) and/or require specialized knowledge (GHz) to construct instruments, which are not widely available. The goal of this review is to illustrate the utility of these experiments in the discovery and study of photovoltaic absorber materials and simultaneously make them more accessible to the community by providing a central tutorial resource. We provide a comprehensive review of how conductivity spectroscopy has developed over the past decade and been applied in the discovery and development of photovoltaic materials, with a primary focus on emerging solution-processable technologies. Along the way we aim to demystify conductivity spectroscopy with focused tutorial sections that explain the physical models used to fit the data and illustrate how to think about “high-frequency conductivity”.

14 SOLAR ENERGY↗
DOE OSTI2025

Ensemble‐Based Spatially Distributed CLM5 Hydrological Parameter Estimation for the Continental United States

Abstract One of the major challenges in large‐domain hydrological modeling efforts lies in the estimation of spatially distributed hydrological parameters while simultaneously accounting for their associated uncertainties. Addressing this challenge is particularly difficult in ungauged locations. With growing societal demands for large‐scale streamflow projections to inform water resource management and long‐term planning, evaluating and constraining hydrological parameter uncertainty is increasingly vital. This study introduces a hybrid regionalization approach to enhance hydrological predictions of the Community Land Model version 5 (CLM5) across the Continental United States (CONUS), with a total of 50,629 1/8° grid cells. This hybrid method combines the strengths of two existing techniques: parameter regionalization and streamflow signature regionalization. It identifies ensemble behavioral parameters for each 1/8° grid cell across the CONUS domain, tailored to three distinct streamflow signatures focused on low flows, high flows, and annual water balance. Evaluating this hybrid method for 464 CAMELS (Catchment Attributes and Meteorology for Large‐sample Studies) basins demonstrates a significant improvement in CLM5 hydrological predictions, even in challenging arid regions. In CONUS applications, the derived spatially distributed parameter sets capture both spatial continuity and variation of parameters, highlighting their heterogeneous nature within specific regions. Overall, this hybrid regionalization approach offers a promising solution to the complex task of improving hydrological modeling over large domains for important hydrological applications.

CLM5↗
DOE OSTI2024

Integrated protonic ceramic electrochemical cell for sustainable energy economy using water-energy nexus framework

Reliance on fossil fuels will continue for the next decades even though there are global pushes away from it to mitigate the overarching climate challenge, most especially by its highest consumers and availability. While there is a hastening global shift away from fossil fuel, integrating its assets into this technology helps limit the risk and future losses of stranded assets and reduce the cost of investment in the new technologies. Moreover, the generation of electricity from intermittent renewable sources like solar and wind has witnessed a significant surge in recent years, leading to a pressing demand for practical energy storage systems. Electrical energy storage is anticipated to play a pivotal role in the future global energy system, facilitating load-leveling operations to support the greater integration of renewable and distributed generation. Reversible electrochemical cells (RECs) offer a promising option for addressing the fossil fuel assets integration and energy storage challenges through the interconversion between electrical and chemical energy and concurrent utilizing carbon emission. In their electrolysis mode, the RECs convert electricity into durable, storable, and portable valuable chemical fuels such as syngas and methane. Conversely, the produced chemical fuels can be used as reactants in the fuel cell mode to generate electricity on demand with minimal (hydrocarbons) or zero when H2 or NH3 is used emissions. However, a challenging goal for this type of technology remains to achieve optimal operation and high roundtrip efficiencies, which has hindered the deployment of previous electrochemical cells. This dissertation demonstrates how reversible protonic ceramic electrochemical cells (RePCECs) can be integrated with fossil fuel power plants and renewable energy sources as a potential energy storage system. In this work, integrated RePCEC systems are designed and examined using computational modeling at scales to determine appropriate system configurations and operating conditions that achieve high roundtrip efficiencies. Cell level design of the PCEC is the first approach, several cells are assembled for the stack level model that is integrated into combined cycle powerplant and solar photovoltaic for the system level model. After critical literature review, this answered the operational and integration research questions proposed to address these challenges. The designed systems perform two functions, utilizing captured CO2 and storing renewable energy through co-electrolysis of steam and CO2. The co-electrolysis reaction involves endothermic water electrolysis and exothermic methanation reaction. To enhance high roundtrip efficiency, there is a need for thermal balance and management in the electrolysis mode. This involves operating the RePCEC stack under conditions that favor methane production to balance out heat needed by water electrolysis, it crucial for the RePCEC system operation. Methanation is enhanced by low temperatures. Leveraging on fabricated BCZYYb-electrolyte RePCEC, the cell model designed revealed that the optimum temperature for methane production is 450℃ at atmospheric pressure. Thus, to achieve optimum system performance, operating in the temperature range 450-525℃ is recommended at the given configuration, combining between the optimum temperature for methane production and temperature for the optimum stack roundtrip efficiency. Configuration with carbon capture system and purge stream is the optimum configuration from the seven conceptualized and evaluated. The modeling outcomes include a thermodynamic examination of integrated RePCEC systems, calibration of cell and stack level models, and steady-state simulation and integration into a 600MW combined cycle power plant retrofitted with two two-stage membrane-based carbon capture system and a wastewater treatment and recovery unit. At 100% powerplant loading, the stack and system roundtrip efficiencies are 72% and 51.37% respectively. Adding a purge stream for produced hydrogen at the system downstream improves the efficiencies to 74 and 55.48% respectively. At atmospheric pressure and 525℃, the system model suggests that a stack roundtrip of 82% is achievable, and overall system efficiency increases by reducing the energy consumption by the balance of plant components for steam generation and storage. Economic analysis of the process gives levelized cost of methane as $2.24/MMBtu lower than the conventional production route that range between $3.46/MMBtu and $9.85/MMBtu. The lifecycle analysis shows that the global warming potential for the production of methane and hydrogen from the RePCEC system is 3.83 kg CO2 eq which is lower than 9.35 kg CO2 eq emission during steam methane reforming for hydrogen production. This answered both the environmental and economic concerns in the raised research question. The proposed RePCEC configuration and analysis carried out in this dissertation to address the surge in renewable energy and challenges with PCEC technology hold significant potential in achieving large-scale energy storage while simultaneously reducing carbon emissions. These advancements, coupled with suitable governmental policies and incentive programs, have the potential to economically disrupt the natural gas industries by using RePCEC systems for methane production, thereby making them more favorable for eventual implementation and commercialization.

25 ENERGY STORAGE↗
DOE OSTI2026

Balancing moisture and oxygen can match the crystallization dynamics of inert halide perovskite processing

Understanding crystallization in ambient environments is essential for scaling the fabrication of halide perovskite solar cells. Antisolvent-free perovskite deposition offers improved compatibility with high-throughput processing but introduces distinct crystallization dynamics relative to the more ubiquitous use of antisolvents in lab-scale perovskite fabrication. These dynamics are driven by interactions between solutes, solvent and the deposition environment. Using in situ wide-angle X-ray scattering during spin-coating and annealing, we demonstrate how relative humidity (RH) and oxygen, can be tuned to drive polytype evolution during ambient crystallization of formamidinium lead iodide to match that of inert synthesis and achieve comparable film and device quality. In an inert (N 2 ) environment, we find that perovskite films follow a well-established 2H → 3C phase transformation with a short period of coexistence of the 4H and 6H phase during heating. During crystallization in dry air (RH 0%), the added presence of oxygen leads to the dominance of 4H intermediate for an extended duration, establishing a 2H → 4H → 3C pathway. Introducing low humidity (RH 10%) suppresses the 4H phase to a short-lived intermediate above 100 °C, facilitating a more direct transition to the desired 3C phase and almost replicating the crystallization behavior observed under inert conditions. Interestingly, films crystallized under RH 10% show a lower onset temperature for the perovskite 3C phase than under N 2 . At higher humidity (RH 40%), the strong interaction of oxygen and moisture with iodoplumbates appears to stabilize higher order polytypes (4H and 6H). Devices fabricated under RH 10% achieve higher efficiency and enhanced stability compared to those produced under inert atmosphere. These findings provide mechanistic insight into crystallization pathways in different environments and provide a framework to transfer processes from inert to ambient conditions. The results highlight the critical role of controlled humidity in tuning antisolvent-free perovskite crystallization for scalable processing.

Hossain, Maimur [Univ. of California, San Diego, C↗
DOE OSTI2023

High-fidelity multiphysics load following and accidental transient modeling of microreactors using NEAMS tools: Application of NEAMS codes to perform multiphysics modeling analyses of micro-reactor concepts

The feasibility of modeling microreactors using high-fidelity models with the Nuclear Energy Advanced Modeling and Simulation (NEAMS) tools is investigated in this report. Three overarching questions guided this research: can NEAMS tools readily be applied for high-fidelity multiphysics modeling of different types of transients in microreactor designs; how accurate are the results obtained; and are improvements needed in accuracy or user experience of NEAMS tools, especially considering newly developed capabilities? This work builds upon FY-2022 work, and two microreactor concepts considering heat pipe (HP-MR) and gas-cooled (GC-MR) technologies were further analyzed using high-fidelity multiphysics simulations. The NEAMS tools considered and coupled within the MultiApp environment are Griffin for neutronics, BISON for thermo-mechanics, Sockeye for heat pipe modeling (in HP-MR), SAM for 1D Fluid – 3D solid modeling of coolant channels and system modeling of balance of plant components (in GC-MR), and the SWIFT code for hydrogen redistribution in hydride moderator. The Heat Pipe MicroReactor (HP-MR) concept was further analyzed in FY-2023 to demonstrate the stochastic TRISO failure modeling capability in BISON to check operational limits of the TRISO fuel. A new full-core Gas-Cooled MicroReactor (GC-MR) model was developed based on the initial assembly-model used in Y-2022 and used for steady-state and accidental depressurization transient simulations. Accuracy of the simulations performed was assessed through 1) verification analyses completed on the different physics with code-to-code comparison, and 2) validation of the multiphysics simulations based on modeling of the Kilopower Reactor Using Stirling Technology (KRUSTY) experiment. In FY-2023, the mesh and model of KRUSTY was updated to closely match publicly available data, and the neutronic model was verified and validated against experimental control rod worth measurements. The multiphysics model of KRUSTY was developed and used for steady-state analysis and for modeling reactivity insertion transient. The calculated power increase and stabilization agrees well with experimental data following adjustment in fuel thermal expansion coefficient. As an important component of this project, the ANL team gathered experience with a wide range of NEAMS tools: the MOOSE Mesh System, Griffin, BISON, SWIFT, Sockeye, SAM, Workbench, and the MOOSE MultiApp System, and provided assessment of new capabilities. Noteworthy are the user assessment of the “vapor-only” flow model in Sockeye and development of a multiphysics startup transient in HP-MR unit cell for use as tutorial in Sockeye. The full-core GC-MR model was used for assessment of SAM for balance of plant modeling and for demonstrating the SWIFT code capability for hydrogen redistribution modeling in multiphysics transient analyses. In this process, several bugs/issues were identified and reported to developers. Finally, the assembly GC-MR model developed in FY-2022 coupling Griffin, BISON and SAM through flow blockage and rod ejection transients was published to the National Reactor Innovation Center (NRIC) Virtual Test Bed (VTB). The Heat Pipe MicroReactor (HP-MR) concept high-fidelity multiphysics coupling of Griffin/BISON/Sockeye in load-following and heat pipe failure transients was also published on the VTB. Those submissions are enabling thorough review of these models as well as wide distribution to industry, regulator, and university users. In this analysis, several new research questions were uncovered, and follow-up analyses are recommended to further improve some models, consider additional transients, and continue development of VTB models.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

From Cell to System: Accelerated hpc Simulations of BESS Aging under Frequency Regulation and Arbitrage use cases

Lithium-ion battery energy storage systems (BESS) packs have emerged as a leading solution for grid-scale energy storage, enhancing resiliency and balancing load fluctuations. Yet, experimental characterization of large-format LIB packs-particularly to assess performance and degradation over hundreds of cycles - demands substantial hardware investment and multi-year testing campaigns. In this work, we couple a hierarchical, physics-based modeling framework agnostic to electrode chemistries with high-performance computing to accelerate systems level evaluation by upto two orders of magnitude. Building on the open-source liionpack platform, we implement cell, module, and pack-scale electrochemical models enriched with mechanistic aging mechanisms and deploy them on an HPC cluster to simulate 150−200kWh systems over 500 - 1,000 cycles with in days. We subject these virtual B ESS to both constant-current cycling and realistic grid service profiles spanning frequency regulation, ramp-rate support, and energy arbitrage-and quantify the resulting degradation patterns. Our results reveal that localized cell aging can induce substantial nonuniformity at module and pack levels, with service-specific cycling protocols driving distinct aging modes. This rapid, multiscale modeling approach provides a powerful design-space exploration tool for optimizing electrical architecture, control strategies, and operational schedules to prolong pack lifetime and lower total cost of ownership.

Ayalasomayajula, Surya [ORNL] (ORCID:0009000860788↗
DOE OSTI2024

A kinetic study of fusion burn waves in compressed deuterium–tritium and proton–boron plasmas

We present particle-in-cell simulations with Monte Carlo collisions of fusion burn waves in compressed deuterium–tritium and proton–boron plasmas. We study the energy balance in the one-dimensional expansion of a hot-spot by simulating Coulomb collisions, fusion reactions, and bremsstrahlung emission with a Monte Carlo model and inverse bremsstrahlung absorption using a new PIC model. This allows us to self-consistently capture the alpha particle heating and radiative losses in the expanding hot-spot and surrounding cold fuel. After verifying our model in a code-to-code comparison with both kinetic and fluid codes for the case of a deuterium–tritium hot-spot, we simulate the expansion of a proton–boron hot-spot initialized at 200 keV and 1,000 g/cm 3 . Our model predicts that energy radiated by the hot-spot is recaptured by the surrounding high-density opaque fuel reducing the expansion work done by the propagating burn wave. As a result, we find the net fusion energy produced over the course of $20$~ps is twice the initial hot-spot energy independent of whether radiation physics is included.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

sciCAN: single-cell chromatin accessibility and gene expression data integration via cycle-consistent adversarial network

The boom in single-cell technologies has brought a surge of high dimensional data that come from different sources and represent cellular systems from different views. With advances in these single-cell technologies, integrating single-cell data across modalities arises as a new computational challenge. Here, we present an adversarial approach, sciCAN, to integrate single-cell chromatin accessibility and gene expression data in an unsupervised manner. We benchmarked sciCAN with 5 existing methods in 5 scATAC-seq/scRNA-seq datasets, and we demonstrated that our method dealt with data integration with consistent performance across datasets and better balance of mutual transferring between modalities than the other 5 existing methods. We further applied sciCAN to 10X Multiome data and confirmed that the integrated representation preserves biological relationships within the hematopoietic hierarchy. Finally, we investigated CRISPR-perturbed single-cell K562 ATAC-seq and RNA-seq data to identify cells with related responses to different perturbations in these different modalities.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Linking Pressure to Electrochemical Evolution in Solid-State Conversion Cathode Composites

Conversion-type cathodes, such as sulfur, FeS 2 , and FeF 3 , offer high theoretical capacities in solid-state lithium batteries but are hindered by substantial volume changes during cycling, leading to interfacial contact loss, crack formation, and microstructural degradation. Here, we investigate the relationships between electrochemical, mechanical, and structural evolution in solid-state electrode composites with these three active materials. Using real-time stack-pressure monitoring, synchrotron X-ray absorption spectroscopy, and electrokinetic modeling, we elucidate how stress evolution is linked to reversible and irreversible redox reactions. Nonlinear stack pressure evolution in cells with sulfur, FeS 2 , and FeF 3 electrode composites is found to arise from material-specific volume changes, the balance of volume change between the working and counter electrode, and the formation of distinct reaction intermediates. The three materials exhibit distinct stack pressure evolution, which is closely related to the different reaction processes in the materials, as demonstrated with X-ray absorption spectroscopy measurements. Through mesoscale modeling, we relate the experimental measurements to species evolution at the particle scale and track the dynamic coexistence of intermediate phases. Our findings highlight the importance of designing for volume changes of a given active material in solid-state battery systems.

batteries↗
DOE OSTI2022

Decorating chromatin for enhanced genome editing using CRISPR-Cas9

CRISPR-associated (Cas) enzymes have revolutionized biology by enabling RNA-guided genome editing. Homology-directed repair (HDR) in the presence of donor templates is currently the most versatile method to introduce precise edits following CRISPR-Cas-induced double-stranded DNA cuts, but HDR efficiency is generally low relative to end-joining pathways that lead to insertions and deletions (indels). We tested the hypothesis that HDR could be increased using a Cas9 construct fused to PRDM9, a chromatin remodeling factor that deposits histone methylations H3K36me3 and H3K4me3 to mediate homologous recombination in human cells. Our results show that the fusion protein contacts chromatin specifically at the Cas9 cut site in the genome to increase the observed HDR efficiency by threefold and HDR:indel ratio by fivefold compared with that induced by unmodified Cas9. HDR enhancement occurred in multiple cell lines with no increase in off-target genome editing. These findings underscore the importance of chromatin features for the balance between DNA repair mechanisms during CRISPR-Cas genome editing and provide a strategy to increase HDR efficiency.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

High Power Density, Carbon Neutral Electrical Power Generation for Air Vehicles

The synergistic integration of a Solid Oxide Fuel Cell-Combustor (SOFC-C) with a turbogenerator (TG) will provide a very high fuel-to-electricity conversion efficiency while maintaining high power-to-weight ratio during high-altitude flight. The proposed SOFC-C-TG power generation technology exceeds the REEACH technical performance targets (TPT). This unique concept addresses many of the challenges faced in all electric propulsion-based aviation. The system has high part-load efficiency (more than 65% lower heating value (LHV)) during long cruise times, load following capability, high-power capacity at high altitudes adapting to low temperatures and pressures, rapid startup time of less than 30 minutes (proven with current SOFC technology), high power density (more than 3.2 kW/kg), efficient thermal management, and a foundation for a compact, efficient electrical storage and power generation system (ESPG). The SOFC-C concept achieves the technology targets by reducing the complexity of traditional fuel cell-gas turbine hybrid systems (FC-GT). The SOFC-C does not require heat exchangers and dramatically reduces the balance of plant increasing power density and performance in efficiency. The reduction in mass through elimination of heat exchangers, external reformer, and other components dramatically decreases the overall thermal dampening of the system which enables rapid startup and load following capability. Direct control of the cathode inlet temperature of the SOFC-C enables rapid warm-up of the SOFC tubes with the ability to reach operating temperature and full power in less than 30 minutes.

03 NATURAL GAS↗
DOE OSTI2023

IPL-Annealed Mixed-Cation Perovskites with Robust Coating Window toward Scalable Manufacturing of Commercial Perovskite Solar Cells

Perovskite solar cells (PSCs) are a promising alternative solar technology, but the technical challenges of (1) stability/durability, (2) efficiency at scale, and (3) manufacturability must be overcome to achieve widespread PSC commercialization. The challenge of balancing solution ink formulation and scalable manufacturing is often overlooked in the literature, where focus is on adopting inks from processes that will not scale. In this study, we apply a classical roll-to-roll manufacturing perspective, utilizing both compositional engineering and intense pulsed light (IPL) annealing, to develop a mixed-cation perovskite ink with a robust coating window that simultaneously solve issues of stability and manufacturability for PSCs. Our method resulted in blade-coated, flexible, mixed-cation PSCs on ITO-PET substrates with a champion power conversion efficiency (PCE) efficiency of 16.7% using IPL annealing of the absorber layer and, to our knowledge, is one of the fastest processing methods for the perovskite layer. This overall reduction in processing time with a stable ink represents an advance toward the scaled production of perovskite solar cells on flexible substrates.

flexible perovskite solar cells↗