Search NASA⌕ Search

SEARCH · Search NASA

Results for “charge separation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

The role of P2O5 in silicate melts

Phase equilibria data in the systems SiO2-P2O5, P2O5-M(x)O(y), and P2O5-M(x)O(y)-SiO2 are employed in conjunction with chromatographic and spectral data to investigate the role of P2O5 in silicate melts. P2O5 depolymerizes pure SiO2 melts by entering the network as a four-fold coordinated cation, but polymerizes melts in which an additional metal cation other than silicon is present. In this complex system P2O5 acts to increase phase separation by further enrichment of the high charge density cations Ti, Fe, Mg, Mn, Ca, in the ferrobasaltic liquid. The dual behavior of P2O5 is explained in a model which requires complexing of phosphate anions and metal cations in the melt. This interaction destroys Si-O-M-O-Si bonds polymerizing the melt. The higher concentration of Si-O-M-O-Si bond complexes in immiscible ferrobasaltic liquids relative to their conjugate immiscible granite liquids explains the partitioning of P2O5 into the ferrobasaltic liquid.

Ryerson, F. J.↗

Investigation of Icing Characteristics of Typical Light Airplane Engine Induction Systems

The icing characteristics of two typical light-airplane engine induction systems were investigated using the carburetors and manifolds of engines in the horsepower ranges from 65 to 85 and 165 to 185. The smaller system consisted of a float-type carburetor with an unheated manifold and the larger system consisted of a single-barrel pressure-type carburetor with an oil-jacketed manifold. Carburetor-air temperature and humidity limits of visible and serious Icing were determined for various engine power conditions. Several.methods of achieving ice-free induction systems are discussed along with estimates of surface heating requirements of the various induct ion-system components. A study was also made of the icing characteristics of a typical light-airplane air scoop with an exposed filter and a modified system that provided a normal ram inlet with the filter located in a position to Induce inertia separation of the free water from the charge air. The principle of operation of float-type carburetors is proved to make them inherently more susceptible to icing at the throttle plate than pressure-type carburetors.. The results indicated that proper jacketing and heating of all parts exposed to the fuel spray can satisfactorily reduce or eliminate icing in the float-type carburetor and the manifold. Pressure-type carburetors can be protected from serious Icing by proper location of the fuel-discharge nozzle combined with suitable application of heat to critical parts.

Coles, W. D.↗

A simple model of electron beam initiated dielectric breakdown

A steady state model that describes the internal charge distribution of a planar dielectric sample exposed to a uniform electron beam was developed. The model includes the effects of charge deposition and ionization of the beam, separate trap-modulated mobilities for electrons and holes, electron-hole recombination, and pair production by drifting thermal electrons. If the incident beam current is greater than a certain critical value (which depends on sample thickness as well as other sample properties), the steady state solution is non-physical.

Beers, B. L.↗

Affinity Electrophoresis Using Ligands Attached To Polymers

In new technique, reduction of electrophoretic mobilities by addition of polyethylene glycol to ligands increases electrophoretic separabilities. In immuno-affinity electrophoresis, modification of ligands extends specificity of electrophoretic separation to particles having surface electric-charge structures otherwise making them electrophoretically inseparable. Modification of antibodies by polyethylene glycol greatly reduces ability to aggregate while enhancing ability to affect electrophoretic mobilities of cells. In hydrophobic-affinity electrophoresis, addition of polyethylene glycol reduces tendency toward aggregation of cells or macromolecules.

Van Alstine, James M.↗

Human Research Program Human Health Countermeasures Element Sensorimotor Risk Standing Review Panel (SRP) Final Report

The Sensorimotor Risk Standing Review Panel (SRP) met at the NASA Johnson Space Center on October 4-6, 2009 to discuss the areas of future research targeted by the Human Health Countermeasures (HHC) Element of the Human Research Program (HRP). Using evidence-based knowledge as a background for risks, NASA had identified gaps in knowledge to address those risks. Ongoing and proposed tasks were presented to address the gaps. The charge to the Sensorimotor Risk SRP was to review the gaps, evaluate whether the tasks addressed these gaps and to make recommendations to NASA s HRP Science Management Office regarding the SRP's review. The SRP was requested to evaluate the practicality of the proposed efforts in light of the realistic demands placed on the HRP. In short, all tasks presented in the Integrated Research Plan (IRP) should address specific risks related to the challenges faced by the astronauts as a result of prolonged exposure to microgravity. All tasks proposed to fill the gaps in knowledge should provide applied, translational data necessary to address the specific risks. Several presentations were made to the SRP during the site visit and the SRP spent sufficient time to address the panel charge, either as a group or in separate sessions. The SRP made a final debriefing to the HRP Program Scientist. Taking the evidence and the risk as givens, the SRP reached the following conclusions: 1) the panel is very supportive of and endorses the present activities of the Sensorimotor Risk; and the panel is likewise supportive of the gaps and associated tasks in the IRP; 2) overall, the tasks addressed the gaps in the IRP; 3) there were some gaps and tasks that merit further enhancement and some new gaps/tasks that the SRP recommends.

Peterson, Barry↗

Human Research Program Human Health Countermeasures Element Bone and Muscle Risk Standing Review Panel (SRP)

The Bone and Muscle Risk Standing Review Panel (SRP) met at the NASA Johnson Space Center (JSC) on October 4-6, 2009 to discuss the areas of current and future research targeted by the Human Health Countermeasures (HHC) Element of the Human Research Program (HRP). Using evidence-based knowledge as a background for identified risks to astronaut health and performance, NASA had identified gaps in knowledge to address those risks. Ongoing and proposed tasks were presented to address the gaps. The charge to the Bone and Muscle Risk SRP was to review the gaps, evaluate whether the tasks addressed these gaps and to make recommendations to NASA s HRP Science Management Office regarding the Panel's review. The Bone and Muscle Risk SRP consisted of scientists who are experts in muscle, bone, or both and could evaluate the existing evidence with sufficient knowledge of the potential effects of long duration exposure to microgravity. More important, although expertise in basic science is important, the SRP was requested to evaluate the practicality of the proposed efforts in light of the realistic demands placed on the HRP. In short, all tasks presented in the Integrated Research Plan (IRP) should address specific questions related to the challenges faced by the astronauts as a result of prolonged exposure to microgravity. All tasks proposed to fill the gaps in knowledge should provide applied, translational data necessary to answer the specific questions. Several presentations were made to the SRP during the site visit and the SRP spent sufficient time to address the panel charge, either as a group or in separate sessions for the Bone and Muscle Risk subgroups. The SRP made a final debriefing to the HRP Program Scientist, Dr. John B. Charles, on October 6, 2009. Taking the evidence and identified risks as givens, the SRP concluded that 1) integration of information should lead to a more comprehensive approach to identifying the gaps, 2) not all tasks addressed the gaps as stated in the IRP, 3) better access should be given to the SRP to existing data to include in its review, and 4) there were some missing gaps and tasks. As a result the SRP recommended 1) combining certain gaps, which in some cases were addressed with identical tasks, 2) additional gaps and tasks to address some of the gaps, 3) deleting some gaps and tasks to better focus the efforts of NASA s HRP in prioritizing their efforts, and 4) prioritizing gaps to address significant issues needing resolution in the short term while maintaining an awareness of long-term goals. The SRP commended the efforts by the HHC Element to integrate knowledge gaps and design tasks to address the higher order questions. This integration did not apply to the Bone and Muscle Risk alone, but the musculoskeletal system as its functions integrate with issues in

Glowacki, Julie↗

Separation and Purification of Mineral Salts from Spacecraft Wastewater Processing via Electrostatic Beneficiation

Electrostatic separation is a class of material processing technologies commonly used for the sorting of coarse mixtures by means of electrical forces acting on charged or polarized particles. Most if not all of the existing tribo-electrostatic separators had been initially developed for mineral ores beneficiation. It is a well-known process that has been successfully used to separate coal from minerals. Potash (potassium) enrichment where underground salt mines containing large amounts of sodium is another use of this techno logy. Through modification this technology can be used for spacecraft wastewater brine beneficiation. This will add in closing the gap be~een traveling around Earth's Gravity well and long-term space explorations. Food has been brought on all man missions, which is why plant growth for food crops continues to be of interest to NASA. For long-term mission considerations food productions is one of the top priorities. Nutrient recovery is essential for surviving in or past low earth orbit. In our advance bio-regenerative process instead of nitrogen gas produced; soluble nitrate salts that can be recovered for plant fertilizer would be produced instead. The only part missing is the beneficiation of brine to separate the potassium from the sodium. The use of electrostatic beneficiation in this experiment utilizes the electrical charge differences between aluminum and dried brine by surface contact. The helixes within the aluminum tribocharger allows for more surface contact when being agitated. When two materials are in contact, the material with the highest affinity for electrons becomes negatively charged, while the other becomes positively charged. This contact exchange of charge may cause the particles to agglomerate depending on their residence time within the tribocharger, compromising the efficiency of separation. The aim of this experiment is to further the development in electrostatic beneficiation by optimizing the separation of ersatz and possibly real wastewater brine residues. In doing so, ideally it will yield a high potassium enrichment for use in spacecraft plant systems.

Miles, John D., II↗

Enhancing the ATIC Charge Resolution

The Advanced Thin Ionization Calorimeter (ATIC) experiment measures the energy spectra of elements, from H to Fe, in the energy region from about 100 GeV to tens of TeV. The ATIC instrument was flown twice in long-duration balloon flights around the South Pole; the ATIC-1 test flight during Dec. 2000 - Jan. 2001 and the ATIC-2 science flight during Dec. 2002 - Jan. 2003. Analyses of both datasets have, to date, relied upon the highly segmented Silicon Matrix (SiM) detector to separate the incident cosmic ray from the calorimeter backscatter and to identify the charge. This method has worked well, enabling ATIC to separate protons from helium and to resolve all the major species up through iron. This charge resolution can be significantly improved by restricting the analysis to particle trajectories that pass through two SiM pixels at the cost of using only a fraction of the potential instrument geometry. However, immediately below the SiM is the two layer SI hodoscope (x, y) consisting of Bicron BC-408 plastic scintillator 2 cm wide, 1 cm thick, 88.2 cm long strips viewed by Hamamatsu R5611 photomultiplier tubes on each end of each strip. The primary purpose of the ATIC hodoscopes is to provide a fast trigger, and each hodoscope includes two crossed layers of strips (42 per layer in the case of Sl) providing supplemental particle trajectory information. The hodoscope readout electronics were designed to provide reasonable charge resolution over the dynamic range from protons through iron. This presentation discusses the S 1 hodoscope energy deposit calibrations, examines the charge resolution possible with this detector and investigates combining the S1 and SiM charge measurements to improve the overall ATIC charge resolution while minimizing degradation of the instrument geometry.

Guzik, T. G.↗

DXL: A Sounding Rocket Mission for the Study of Solar Wind Charge Exchange and Local Hot Bubble X-Ray Emission

The Diffuse X-rays from the Local galaxy (DXL) mission is an approved sounding rocket project with a first launch scheduled around December 2012. Its goal is to identify and separate the X-ray emission generated by solar wind charge exchange from that of the local hot bubble to improve our understanding of both. With 1,000 square centimeters proportional counters and grasp of about 10 square centimeters sr both in the 1/4 and 3/4 keV bands, DXL will achieve in a 5-minute flight what cannot be achieved by current and future X-ray satellites.

Galeazzi, M.↗

MOS Circuitry Would Detect Low-Energy Charged Particles

Metal oxide semiconductor (MOS) circuits for measuring spatially varying intensities of beams of low-energy charged particles have been developed. These circuits are intended especially for use in measuring fluxes of ions with spatial resolution along the focal planes of mass spectrometers. Unlike prior mass spectrometer focal-plane detectors, these MOS circuits would not be based on ion-induced generation of electrons, and photons; instead, they would be based on direct detection of the electric charges of the ions. Hence, there would be no need for microchannel plates (for ion-to-electron conversion), phosphors (for electron-to-photon conversion), and photodetectors (for final detection) -- components that degrade spatial resolution and contribute to complexity and size. The developmental circuits are based on linear arrays of charge-coupled devices (CCDs) with associated readout circuitry (see figure). They resemble linear CCD photodetector arrays, except that instead of a photodetector, each pixel contains a capacitive charge sensor. The capacitor in each sensor comprises two electrodes (typically made of aluminum) separated by a layer of insulating material. The exposed electrode captures ions and accumulates their electric charges during signal-integration periods.

Sinha, Mahadeva↗

Electrostatic Regolith Interaction Experiment (ERIE) Electrometer Instrument Development

The Electrostatic Regolith Interaction Experiment (ERIE) is a joint venture between the University of Central Florida (UCF) Center for Microgravity Research (CMR) and the NASA Kennedy Space Center (KSC) Electrostatics and Surface Physics Laboratory (ESPL) seeking to examine charged dust grain behavior in a microgravity environment. Two separate systems have been combined for this suborbital flight experiment: the COLLisions Into Dust Experiment (COLLIDE) developed by the UCF CMR and the Wheel Electrostatic Spectrometer (WES) developed by the NASA KSC ESPL. This combination will advance the understanding of the natural and induced charged grain behavior on the Moon, asteroids, and other low gravity bodies comprised of charged dust particles. COLLIDE retains granular material under vacuum in a shallow tray behind a metal door, which then opens and releases the particles into a larger open volume when microgravity is achieved. The experiment is observed with a high-speed camera, such that the motions of these particles can then be tracked so the kinematics of each grain may be analyzed. The original application for this apparatus was to study cratering events into granular beds, but electrostatic repulsion was detected in the early frames of the video data returned from completed experiments, so a re-flight with a focus on these events was proposed. Agitation of the grains during launch combined with the frictional charge transfer between the grains and the door as it slides open provides an opportunity to use this setup to observe material tribocharging and charged particle behaviors in microgravity. In this updated version, the charged particles released into the chamber will traverse through an electric field produced by high voltage parallel plates and their resulting trajectories will be determined by their net charges. WES was originally developed to characterize the triboelectric properties of the Martian regolith through the contact of a rover wheel with the surface as it rotates. Improvements were made upon this legacy system to develop a sensor suite that will be installed within the COLLIDE door to measure charge transferred between the granular material and insulating disks protruding through the door. These insulator disks span the triboelectric series so, as they slide across the particulate matter when the door opens, each will accumulate a charge consistent with its relative position to the grains within the series. This charge on each insulator is distributed between two capacitances in series with an electrometer amplifier returning an analog voltage proportional to the charge accumulated. Calibration of this system has been performed using applications of known charge to the inputs and characterization of the frictional charge transfer between various regolith simulants and the sensor insulators is currently being examined in the lab.

Electrostatics↗

Electrostatic Regolith Interaction Experiment (ERIE) Electrometer Instrument Development

The Electrostatic Regolith Interaction Experiment (ERIE) is a joint venture between the University of Central Florida (UCF) Center for Microgravity Research (CMR) and the NASA Kennedy Space Center (KSC) Electrostatics and Surface Physics Laboratory (ESPL) seeking to examine charged dust grain behavior in a microgravity environment. Two separate systems have been combined for this suborbital flight experiment: the COLLisions Into Dust Experiment (COLLIDE) developed by the UCF CMR and the Wheel Electrostatic Spectrometer (WES) developed by the NASA KSC ESPL. This combination will advance the understanding of the natural and induced charged grain behavior on the Moon, asteroids, and other low gravity bodies comprised of charged dust particles.

Electrostatics↗

Production and optical constraints of ice tholin from charged particle irradiation of (1:6) C2H6/H2O at 77 K

Fifty separate irradiations of a 6:1 mixture of H2O/C2H6 ice conducted over a 5-month period have yielded sufficient tholin for the determination of its physical constants in the 0.06 to 40 micron range. While the imaginary part of the refractive index k was obtained by transmission measurements on thin-film samples and Kramers-Kronig analysis (KKA), the real part of the refractive index was obtained by KKA and ellipsometry; these data may prove useful in cometary and outer solar system spectrometric interpretation.

Khare, B. N.↗

Separating Magnetospheric and Heliospheric SWCX in X-ray Spectra

Solar wind charge exchange (SWCX) emission contaminates all astrophysical observations in X-rays regardless of the direction. This contamination is particularly problematic when measuring astrophysical plasma temperatures due to the similar spectral distribution of the two phenomena. Since its discovery, literature has distinguished between SWCX emission resulting from solar wind-neutral interactions within the Earth’s magnetosphere, called magnetospheric SWCX, and similar interactions occurring more generally throughout the heliosphere, called heliospheric SWCX. Previous work demonstrated accurate modeling of the heliospheric SWCX contribution for astrophysical observations performed at low ecliptic latitude with HaloSat, a CubeSat X-ray mission of medium spectral resolution. Here, we apply this model to similarly orchestrated observations to measure the magnetospheric SWCX contribution separately from the heliospheric SWCX and the astrophysical background contributions. We describe our observational strategy, the heliospheric SWCX model used, and our spectral fitting methods. In particular, we report on four observations with lines of sight through the Earth’s magnetospheric flank with total O VII line fluxes at least 3σ above that predicted by the heliospheric SWCX model and the astrophysical background, possibly indicative of magnetospheric SWCX. We then discuss the excess emission in comparison with available magnetospheric SWCX simulations requested through the Community Coordinated Modeling Center.

X-ray↗

Ion optics system incorporating radio frequency mass separation

Results of an experimental study are presented. They show that an RF mass discriminator, based on a Bennett mass spectrometer concept, can be used to discriminate between two species of ions with about a 2-to-1 charge-to-mass ratio. Such a device would be useful for separating monatomic and diatomic oxygen ions in a system designed to simulate the environment that spacecraft encounter in low earth orbit. The influence of changing mass discriminator parameters - such as the spacing of its grids, the amplitude and frequency of RF voltage signals applied to it and the current density of ions incident upon it - on its species discrimination capabilities is discussed. Experimental results are also compared to the results of a simple theoretical model to gain insight into the processes occurring in the discriminator. These results are shown to be in good agreement.

Anderson, John R.↗

Improved anode design for metal-oxygen cells

Method for returning electrolyte to the anode compartment in metal-oxygen second battery cells eliminates the problem of the anode drying out during charge-discharge cycling. Electrolyte forced out of the separator is returned to the anode by a microporous insert and wicking material.

Arrance, F. C.↗

Thin electrostatically self-focusing electron streams.

Study of 30 to 380 microampere, 50 to 550 V, 1 to 2 mm, electrostatically self-focusing electron streams (50 cm long) drifting through mercury vapor (at 50 microtorr to 2 millitorr) in a tube with a radius of 6.6 cm. The inside surface of the tube is coated with a transparent layer whose resistivity is 50 ohm-cm per centimeter. In order to determine the charged-particle densities and the potential profile in and around the beam without disturbing the system, a multigrid electrostatic charged particle energy analyzer was used to study separately the energy distributions of both ions and electrons ejected radially from the beam. The results show two energy groupings for electrons. The energy distribution of the high-energy group is produced by ionizing collisions between beam electrons and neutral gas atoms; a group of flow-energy electrons becomes trapped in the potential well within and around the beam, subsequently escaping by collisional mechanisms.

Mccorkle, R. A.↗

Quadrupole mass filter with means to generate a noise spectrum exclusive of the resonant frequency of the desired ions to deflect stable ions

A mass spectrometer for the separation or separate indication of ions of different specific electric charges is reported. The instrument uses a periodically varying electric field in its analyzing section to excite the injected ions into oscillations while traveling along their trajectories which are either stable or unstable depending on specific parameters. Only stable trajectory ions pass through the electric field to the collector for indication.

Langmuir, R. V.↗