Search NASA⌕ Search

SEARCH · Search NASA

Results for “combustibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Silicon alloying enhances fast heating rate combustion of aluminum particles

Alloys and composites of aluminum (Al) have shown promise in regulating and enhancing particle combustion for energy generation applications. Recent work on aluminum-silicon (Al-Si) spherical alloy particles has shown improved combustion at low heating rates through enhanced diffusion accompanying a lower melting temperature. This study extends reactivity analysis to higher heating rates, comparing oxidation of Al-Si with Al. Flame speeds of Al-Si powder mixed with molybdenum trioxide (MoO 3 ) powder (Al-Si+MoO 3 ) exhibited a faster transition to steady propagation relative to Al+MoO 3 . Bomb calorimetry experiments revealed up to 5.8% greater early temperature rise for Al-Si powder. Rapid steady propagation for Al-Si mixture and faster temperature rise for Al-Si particles were attributed to accelerated kinetics evidenced in thermal equilibrium analysis of the mixtures using a differential scanning calorimeter (DSC). Larger DSC exotherms in the early stages of oxidation (i.e., 480–720 °C) correlated with early heat release and promoted steady flame propagation for Al-Si+MoO 3 compared with Al+MoO 3 . Furthermore, in multiple heating rate DSC studies, Al-Si+MoO 3 ignited at a lower heating rate (i.e., 15 ⁰C/min) than Al+MoO 3 (i.e., 20 ⁰C/min). Both mixtures ignited at temperatures less than 625 °C which is above the melting temperature of Al-Si (574 °C) and below Al (659 °C). Thus, alloy particle fuels with enhanced diffusion-controlled kinetics promote steady flame propagation and show promise for energy generation applications. This is especially promising for technologies driven by enhanced condensed phase combustion such as some propellant additives or applications dependent on reliable burn rates such as pyrotechnic time delay formulations and primers.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Aerodynamic effects on outer ash deposition rates in second generation atmospheric pressure oxy-coal combustion systems

Recent measurements in scenarios representative of second generation atmospheric pressure oxy-coal combustion systems have shown a significant increase in ash deposition rates in comparison to combustion in air. However, the causative mechanisms behind this increase have not been well understood. To fill this void, well-characterized experiments including fuel and deposit particle size distributions (PSDs) were coupled with highly resolved numerical simulations to isolate the aerodynamic effects impacting the deposition process such that mechanisms could be hypothesized. Three combustion scenarios (AIR, OXY27, OXY70) spanning a factor of three variation in flue gas volumetric flow rates were simulated and the deposition characteristics (impaction rates, deposit PSD, temperature, residence times, capture rates) tracked/predicted using a customized deposition module. The measured deposit PSD was significantly different from the PSD of the parent fuel indicating significant physio-chemical transformations (coalescence and particle growth in particular) at play. The use of simplistic modeling approaches (swelling parameter variations) to model particle growth led to inaccurate deposit ash PSD and rate predictions. A more satisfactory agreement between the measurements and simulations was obtained when the functional form of the parent fuel PSD (spread parameter) was modified to conform closely to the deposit PSD while still ensuring the fidelity of temperature and velocity predictions. Based on the measured ash compositions, identical capture criteria were employed across all three scenarios. Here this study further supports the theory that the ash deposition rates in these systems are dominated by aerodynamic effects with the ash PSD playing a dominant role.

42 ENGINEERING↗
DOE OSTI2025

Co-optimization of fuel properties, combustion system geometry, and injection strategy for conventional diesel fuel

Here, studies have shown that fuel properties can impact an engine’s operation in several ways, including ignition delay, sooting tendency, mixture formation, and combustion temperature. In mixing-controlled compression ignition (MCCI) engines, the fuel system design and piston bowl geometry significantly affect combustion performance and emissions. Based on current information, it is difficult to draw conclusions about fuel property effects and sensitivities. The central fuel hypothesis approach used in the US Department of Energy Co-Optima program has worked well for spark ignition fuels: identifying critical fuel property ranges is sufficient to screen fuel blends that are expected to maximize efficiency and reduce pollutant emissions. However, for MCCI-relevant fuels, the information gained from past studies is not sufficient to build such a merit function or to allow for performing a similar screening of fuel blends. It is hypothesized that a co-optimization of a fuel’s physical and chemical properties, combustion system geometry, and injection strategy could leverage synergies between the effects of the fuel properties and geometries, resulting in improved performance over state-of-the-art. A machine learning–assisted unconstrained global optimization algorithm was used to explore a design space comprising 23 independent variables. The results show that physical property effects were minimal even for large variations in fuel properties, and the only interaction effect that was observed was the effect of varied fuel density parameters on fuel/air mixture formation. Nevertheless, these interactions were not sufficient in magnitude to significantly affect optimization results. Therefore, analysis of the results suggests that fuel physical properties cannot be leveraged in a co-optimization context to increase engine efficiency.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Physical solvents and techno-economic analysis for pre-combustion CO 2 capture: A review

In this manuscript we review the use, development, and economic performance of physical solvents for pre-combustion CO 2 capture from high pressure H 2 rich syngas streams. Commercially available physical solvents are presented, followed by an assessment of the ideal properties that are important for development of novel solvents for CO 2 capture from high-pressure syngas streams. To compare the technical and economic performance of traditional and novel physical solvents, a review of the methods, assumptions and models used in techno-economic analysis (TEA) studies was conducted. It was found that, although some novel solvents show promising technical performance in the laboratory (e.g., high CO 2 absorption capacity and low vapor pressure), other issues (e.g., solvent viscosity and cost) may limit their industrial applications. Process simulations were useful tools for modeling the technical performance of processes using traditional and novel solvents. However, model predictions are most reliable when the methods and correlations used to develop the process simulation are validated with representative experimental data, in particular highly accurate baseline models are required for fair comparison among physical solvents. The key inputs and assumptions in pre-combustion CO 2 capture TEAs have also been summarized. Some studies showed that the promising technical performance of novel physical solvents can be offset by the high and often unknown costs of these solvents. Future development of novel physical solvents for pre-combustion CO 2 capture will benefit from more studies that conduct in-depth techno-economic analysis, specifically with validated process simulations and transparent economic models.

42 ENGINEERING↗
DOE OSTI2025

Beta-Amino Carboxylate (BAC) non-aqueous physical solvents for enhanced CO2 separations in pre-combustion carbon capture, industrial CO 2 capture, and biogas upgrading processes

Novel beta-amino carboxylate (BAC) solvents have been synthesized and tested to efficiently capture carbon dioxide (CO 2 ) from process gas streams with CO 2 partial pressure intermediate between pre-combustion and post-combustion capture. The BAC solvents have molecular structures characterized by alkyl-substituted amides or esters containing a secondary amine functional group on the second carbon from the carbonyl carbon (referred to as the beta “β” carbon). The ester or amide functional group combined with optimal steric crowding around the amine nitrogen by proximate alkyl groups are tailored to modify the strength of CO 2 binding in the solvent. The solvents possess high CO 2 solubilities and high gas selectivity including good CO 2 /H 2 O selectivity and can be utilized for CO 2 absorption over a range of partial pressures. Due to low volatility, many of the solvents can be operated at or above ambient temperature which eliminates solvent chilling and allows regeneration using low grade waste heat. These novel solvents offer an opportunity for efficient carbon capture for a range of applications including biogas upgrading, hydrogen production, and pre-combustion carbon capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Evaluation of methods for characterizing the fine particulate matter emissions from aircraft and other diffusion flame combustion aerosol sources

The U. S. Environmental Protection Agency in collaboration with the U. S. Air Force Arnold Engineering Development Complex conducted the VAriable Response In Aircraft nvPM Testing (VARIAnT) 3 and 4 test campaigns to compare nvPM emissions measurements from a variety of diffusion flame combustion aerosol sources (DFCASs), including a Cummins diesel engine, a diesel powered generator, two gas turbine start carts, a J85-GE-5 turbojet engine burning multiple fuels, and a Mini-CAST soot generator. The VARIAnT research program has conducted four test campaigns to date with the VARIAnT 3 and 4 test campaigns focusing on BC mass instrument performance, use of gas turbine engine sources for BC mass instrument calibration, and the characterization of the aerosols produced from the combustion sources. Results from both campaigns revealed agreement of about 20% between the AVL Micro-Soot Sensor, the Cavity Attenuated Phase Shift (CAPS PMSSA) monitor and the thermal-optical reference method for elemental carbon (EC), independent of the calibration source used. For the Artium LII-300, the measured mass concentrations in VARIAnT3 fall within 18% and in VARIAnT4 fall within 32% of the reference EC mass concentration when calibrated on a combustor rig in VARIAnT3 and on a LGT-60 start cart in VARIAnT4, respectively. It was also found that the three mass instrument types (MSS, CAPS PMSSA, and LII-300) can exhibit different BC to reference EC ratios depending on the emission source that appear to correlate to particle geometric mean mobility diameter, morphology, or some other parameter associated with particle geometric mean diameter (GMD) with the LII-300 showing a slightly stronger apparent trend with GMD. Systematic differences in LII-300 measured mass concentrations have been reduced by calibrating with a turbine combustion source (combustor or turbine engine). With respect to the particle size measurements made, the sizing instruments (TSI SMPS, TSI EEPS, and Cambustion DMS 500) were found to be in general agreement in terms of size distributions and concentrations with some exceptions. Teflon filter measurements of the total aerosol mass produced by the various DFCASs differed from the reference EC, BC, and integrated particle sized distribution measured aerosol masses. The Teflon filter measured mass was 30 to 40% greater than the reference EC and 50 to 60% greater than the BC mass for the J85 in both test campaigns. The measurements of particle size distributions and single particle analysis by miniSPLAT indicated the presence of large particles (>100 nm) having more compact morphologies, higher effective density, and a composition dominated by OC and ash. This increased large particle fraction is also associated with higher values of single scattering albedo measured by the CAPS PMSSA instrument and higher OC/EC measurements. These measurements indicate gas turbine engine emissions can be a more heterogeneous mix of particle types beyond the original E31 assumption that it is mainly composed of black carbon.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Recent advances in combustion science related to hydrogen safety

Hydrogen is a key pillar in the global Net Zero strategy. Rapid scaling up of hydrogen production, transport, distribution and utilization is expected. This entails that hydrogen, which is traditionally an industrial gas, will come into proximity of populated urban areas and in some situations handled by the untrained public. To realize all their benefits, hydrogen and its technologies must be safely developed and deployed. The specific properties of hydrogen involving wide flammability range, low ignition energy and fast flame speed implies that any accidental release of hydrogen can be easily ignited. Comparing with conventional fuels, combustion systems fueled by hydrogen are also more prone to flame instability and abnormal combustion. This paper aims to provide a comprehensive review about combustion research related to hydrogen safety. It starts with a brief introduction which includes some overview about risk analysis, codes and standards. The core content covers ignition, fire, explosions and deflagration to detonation transition (DDT). Considering that DDT leads to detonation, and that detonation may also be induced directly under special circumstances, the subject of detonation is also included for completeness. The review covers laboratory, medium and large-scale experiments, as well as theoretical analysis and numerical simulation results. While highlights are provided at the end of each section, the paper closes with some concluding remarks highlighting the achievements and key knowledge gaps.

08 HYDROGEN↗
DOE OSTI2020

Effects of dilution and pressure on combustion characteristics within externally heated micro-tubes

Here this study investigates the impact of pressure and dilution on combustion behavior of of C 2H6/air/N2 mixtures within an externally heated micro-tube using both experimental and analytical techniques. Experiments are conducted for pressures up to 10 bar at multiple dilution levels and document three flame regimes, i.e. weak flames, FREI and normal flames. Characteristic temperatures for flame stabilization, as well as and ignition and extinction are obtained by applying a novel thin filament pyrometry method (TFP), which uses a thin silicon carbide (SiC) filament that enables temperature measurements for both reacting and non-reacting cases. Results show a decrease of characteristic temperatures with increasing pressure, which can be which can be partially compensated by a decrease of O2 content. Further, regime transitions occur at lower velocity as the pressure increases, whereas weak flame positions are insensitive to dilution at a given pressure. Predictions from the analytical model compare favorably with experimental results. The most prominent finding is that as dilution increases, the transition from weak flame to FREI becomes less abrupt and is completely lost for high dilution levels (i.e. low O2 content). Both experimental and analytical results indicate that the unstable FREI combustion regime does not exist at high dilution levels, i.e. weak flame and normal flame regimes are no longer clearly separated. As FREI are interpreted as a cyclic transition from an ignition zone to a propagating flame, results for highly diluted conditions are interpreted as a combustion regime where classical flame propagation ceases to exist.

42 ENGINEERING↗
DOE OSTI2022

DNS Of the ignition process of n-heptane/air premixed combustion with low-temperature chemistry in turbulent boundary layer

In the present work, three-dimensional direct numerical simulation (DNS) of n-heptane/air premixed combustion in turbulent boundary layer was performed to explore the near-wall ignition process with low -temperature chemistry. A reduced chemical mechanism with 58 species and 387 elementary reactions for n-heptane combustion was used in the DNS. The general characteristics of the ignition process near the wall were examined. Here, it was found that low-temperature ignition (LTI) dominates the upstream region, and high -temperature ignition (HTI) appears in the downstream region. The ignition process and the low-temperature chemistry pathways of the DNS are compared with those of a corresponding laminar case. It was found that the ignition process was affected by turbulence, which results in thickened reaction zones. However, the carbon flow analysis of low-temperature chemistry showed that turbulence rarely affects the low-temperature chemistry pathway. The combustion modes of various regions were scrutinized based on the budget terms of species transport equations and the chemical explosion mode analysis (CEMA). It was shown that the reaction term of RO 2 is significant during the LTI process of the upstream region, and the reaction terms of CH 2 O and CO 2 are evident in the downstream region, indicating the occurrence of HTI. It was also shown that auto-ignition is dominant in the upstream region. With increasing streamwise distance, the contribution of flame propagation increases, which takes over that of auto-ignition in the near-wall region.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

SootLib: A soot model library for combustion simulation

Soot formation in combustion is an important process that affects radiative heat transfer, flame temperatures, and emissions with health and environmental impacts. Soot formation involves complex chemistry for nucleation, growth, oxidation, and coagulation processes. The soot particles vary widely in size and accurate modeling requires representation of the particle size distribution (PSD). Modeling soot is not trivial, and is only one of several physical processes active in combustion systems. This paper presents a software package called SootLib, which is an open-source library for modeling soot formation and other aerosol systems. SootLib is written in C++, is documented with Doxygen, and is available on GitHub. The library includes several models for soot chemistry and coagulation, and it represents the PSD using either a sectional model or the method of moments (MOM). Four closure approaches for the MOM are implemented allowing up to eight moments: monodispersed, an assumed-shape lognormal distribution, the quadrature method of moments, and the method of moments with interpolative closure. SootLib provides an interface for inclusion in other combustion packages including CFD or reacting flow solvers. The range of models allows comparisons and sensitivity studies, and the modularity facilitates extension to other soot models.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Numerical Analysis of Combustion Dynamics in a Full-Scale Rotating Detonation Rocket Engine using Large Eddy Simulations

Large eddy simulations (LES) using detailed chemistry and leveraging adaptive mesh refinement (AMR) are performed to gain insights into the combustion dynamics within a full-scale methane-oxygen non-premixed rotating detonation rocket engine (RDRE) employing impinging discrete injection schemes. In particular, a comparative analysis of two operating conditions corresponding to the same global equivalence ratio but different mass flow rates is carried out to investigate the resultant impact on detonation wave characteristics and RDRE global performance. Multiple co-rotating detonation waves with spatially-distributed wave structure and preferential alignment with the inner wall of the annulus (due to asymmetry in fuel distribution) are encountered under both conditions. Both cases exhibit pre-detonation deflagrative burning in the fill region, while one of the cases shows higher susceptibility to backflow into the feed plenums due to lower plenum pressures. Furthermore, heat release analysis shows that the thrust obtained from the RDRE is closely linked to the distribution of total heat release between detonative and deflagrative combustion. On the other hand, combustion efficiency is associated with the fraction of heat release occurring in fuel-rich versus fuel-lean regions within the RDRE.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

High-speed phase contrast imaging of spray breakup of jet fuels under combusting conditions

X-ray phase contrast imaging is conducted at 90,517 Hz on a fuel spray to characterize the breakup of the bulk fuel into ligaments and individual droplets in a single-sector, swirl-stabilized combustor under reacting conditions. Phase contrast imaging is used to qualitatively assess spray breakup for two fuels: Jet-A, which represents a normal viscosity fuel, and a blend of JP-5 (64%) and farnesane (36% by volume), which represents a high-viscosity fuel, at three fuel-flow rates and two air inlet temperatures. Time-series images of the fuels show that atomization occurs much more rapidly at higher fuel pressure with thinner ligaments being rapidly shredded. The high-viscosity fuel is qualitatively observed to have markedly longer, thicker ligaments and larger droplet diameters after the primary breakup than the normal viscosity fuel. Using an image processing and droplet quantification strategy, the mean droplet velocity magnitudes were found to decrease with decreasing fuel pressure and fuel-flow rate. The increase in preheat temperature from 323 to 370 K results in an increase in the mean droplet velocity magnitude and a decrease in numerical average and Sauter mean diameter, indicating improved atomization. The high-viscosity fuel was found to have larger average droplet diameters at each condition than the normal viscosity fuel. The increased preheat is found to enhance the combustion efficiency, which is hypothesized to couple with the improved atomization due to the higher combustion temperatures. This indicates the importance of examining spray atomization and breakup under realistic combusting conditions for relevant fuels as the heat release directly couples with the atomization process.

42 ENGINEERING↗
DOE OSTI2020

Methyl propyl ether combustion

Ethers are potential diesel blendstocks that have high cetane numbers and identified cost-effective production pathways. Among ethers, methyl propyl ether (MPE) is a small enough molecule to build a good detailed model for and a large enough molecule for studying key intramolecular hydrogen migrations involved in low-temperature feedback loops for larger ethers. In this study, a model was generated for the combustion of MPE from 600-900 K and 10-20 bar using the Reaction Mechanism Generator (RMG) package. Results from rapid compression machine (RCM) experiments were used to validate the kinetic model. At low temperatures, the generated model successfully captured the dominant low-temperature feedback loops. At higher temperatures, propanal is a major combustion intermediate for PME, suggesting that aldehydes likely play a significant role in larger ethers' combustion.

09 BIOMASS FUELS↗
DOE OSTI2022

Combustion Kinetics Model Development & Fluid Property Experimental Investigation For Improved Design Of Supercritical CO 2 Power Cycle Components

Supercritical carbon dioxide (sCO 2 ) cycles are being investigated for the future of power generation and will contribute to a carbon-neutral future to combat the effects of climate change. These direct-fired closed cycles will produce power without adding significant pollutants to the atmosphere. For such cycles to be efficient, they will need to operate at significantly higher pressures (e.g., 300 atm for Allam Cycle) than existing systems (typically less than 40 atm). There is limited knowledge on combustion at these high pressures and with a high dilution of carbon dioxide. Also, various experimental and computational investigations and model developments have been performed by the University of Central Florida (UCF), Embry-Riddle Aeronautical University (ERAU), and Stanford University (S.U.) to improve the current knowledge base and support the design and development of sCO 2 combustors. This project's technical aspects include chemical kinetics development, fundamental sCO 2 combustion, combustion model and sub-model development, supercritical fluid injection characterization, and heat transfer characterization.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

High Inlet Temperature Combustor for Direct-Fired Supercritical Oxy-Combustion

It is envisioned that supercritical CO 2 (sCO 2 ) electric power plant efficiencies can exceed 52% with 99% carbon capture using direct-fired oxy-combustion. Such efficiencies would be competitive with Natural Gas Combined Cycles (NGCC) and operate with nearly zero carbon emissions. To achieve high plant efficiencies, turbine inlet conditions must approach 1,200 °C at 250 bar. Such conditions, while desirable from a systems perspective, exceed the current state of the art in turbine design and materials qualification. The team of Southwest Research Institute ® (SwRI ® ), Georgia Institute of Technology (Georgia Tech), Spectral Energies, LLC (Spectral), GE Global Research (GE-GRC), and the University of Central Florida (UCF) sought to demonstrate an intermediate step toward these high efficiency plants with the development of a 1 MWth, subscale direct-fired oxy-fuel combustor. The efforts focused largely on the development of an auto-ignition based combustion system capable of providing the targeted 1200 °C and the pilot-scale plant to operate the combustor. While the project was stopped short of the commissioning and demonstration work, the advances made in this effort will reduce risks associated with chemical kinetics, thermal management, water separation, flue gas cleanup, materials selection, and corrosion in future demonstration efforts for the direct-fired oxy-fuel combustion cycles. The following report documents the design, analysis, and installation efforts completed during the project periods of performance.

03 NATURAL GAS↗
DOE OSTI2023

Surface Roughness Effects from Additive Manufacturing in High Efficiency Gas Turbine Combustion Systems

In the past, clean combustion systems were characterized by high system development costs due to growing complexity and escalating manufacturing costs from conventional manufacturing processes. As a result, high efficiency concepts are difficult to design and more difficult to be cost-effectively manufactured. In recent years, with the introduction of additive manufacturing (AM) technologies, the rapid prototyping and mass production processes of clean combustion systems are promising to be significantly simplified with significant reduction in terms of engine manufacturing cost and engine energy cost. Compared with conventional manufacturing built parts, the AM process enabled a simpler design to be adopted for the nozzle, reducing the number of required braze and weld joints from twenty-five to just five. The resulting nozzle was 25% lighter and five times more durable and contributed to a 15% reduction in fuel burn in comparison with the previous model produced. Applying these improvements to a fleet of 5,000 turbofan engines at 150 kN thrust would result in fuel cost savings of $6B annually (at $5/gallon Jet-A fuel price, 700 gallon/hour fuel consumption rate, and 2,300 operational hours per year),and reduce CO2 emissions by more than 25 million tons per year. These advances support core Department of Energy (DOE)missions in energy efficiency, improving productivity, and environmental sustainability. Maximizing the benefit of these new capabilities will require high prediction capability of high speed turbulent flow with wall modeled Large Eddy Simulation (LES). GE Aviation maintains that advanced simulation technology and supercomputing is required in order to provide the appropriate boundary conditions to realize the maximum potential of AM and Ceramic Matrix Composite to reduce cooling flow, a first order penalty on the Brayton cycle. The algorithm developed using the ANSYS/Fluent software would provide the foundation for entirely new avenues of research and development with potential multi-billion dollar impact to the US economy, and significant reduction in carbon based emissions across the aerospace and power generation industries. The formulation of this iWLES (integral wall model for LES) is generic and allows to capture the changes in flow dynamics that have a significant impact on the wall bounded flow characteristics, such as swirler effective area, bulk swirl number, local pressure distribution, exit velocity profile, and turbulence kinetic energy profile. A periodic channel flow with rough flat plate is simulated using LES (Wall-Adapting Local Eddy-viscosity) model to verify the implementation of iWLES in the Fluent User Defined Function (UDF). As the flow fields are highly sensitive due to surface roughness of the wall bounded flows in the combustion systems, there is significant potential to conduct further LES studies focusing on the turbulence boundary layer interaction. Accurately capturing near wall physics will elucidate the impact of rough surfaces on combustor flow and aero-thermal interactions.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

1D Simulation of Avalanche to Streamer to Spark Transition of Plasma Discharge in Ammonia-Air Combustion

The backward problem of plasma assisted combustion emphasizes evaluating the effect of the evolving thermochemical state on the plasma discharge. This paper investigates the dependence of avalanche to streamer to spark formation dynamics and kinetics on the gas composition and temperature at different points in an ammonia-air premixed laminar flame using a self-consistent multigrid-based 1D plasma solver. Different values of ..alpha.., the coefficient for effective ionization events per unit length, have been reported for electron avalanches in air and stoichiometric NH3-air mixtures. The streamer inception has been shown to obey the Meek's criterion. An exponential reduction in streamer and spark formation time has been observed from plasma simulations at different points in the unburnt, pre-heat zone, reaction zone and the fully burnt regions of the premixed flame. While the enhancement of the reduced electric field with increasing temperature affects effective ionization, there exists a minimum breakdown field for streamer formation, which does not vary proportionally with the changing number density of the gas. The change in the mixture from reactants (NH3, O2, N2) to products of complete combustion of ammonia in air (N2, H2O) has also been shown to affect the streamer and spark formation. Finally, the major pathways during the streamer and spark phases which are responsible for producing important radicals used in combustion of NH3 are also discussed.

ADVANCED PROPULSION SYSTEMS,INORGANIC, ORGANIC, PH↗
DOE OSTI2025

Examination of coal combustion management sites for microbiological and chemical signatures of groundwater impacts

Coal combustion accounts for 40% of the world’s electricity and generates more than a billion tons of coal combustion products (CCP) annually, half of which end up in landfills and impoundments. CCP contain mixtures of chemicals that can be mobile in the environment and impact the quality of surface water and potable groundwater. In this investigation, water samples from 14 coal combustion management sites across 4 physiographic regions in the United States, paired with background and down-gradient groundwater samples, were analyzed for water chemistry and microbiology. The objective was to determine if microbiology data alone, or supported by chemistry data, could reliably differentiate source waters and identify sites where CCP is known or expected to be influencing groundwater. Two percent of the total amplicons showed genus level conservation across CCP management sites, regions, and sample types; corresponding to ubiquitous, facultatively aerobic proteobacterial taxa that are generally recognized for the potential to respire using different terminal electron acceptors. Ordination plots did not reveal significant differences ( p > 0.05) in 16S rRNA gene amplicon diversity by CCP management site, water sample types, or physiographic regions. Contrastingly, chemistry distinguished sample types by standard water quality metrics (total dissolved solids, Ca:SO 4 ratio), alkali earth metals (K, Na, Li), selenium, boron, and fluoride. A focused evaluation of 16S rRNA gene amplicons for a subset of CCP management sites revealed microbiological features and chemical drivers (F, Ca, temperature) that positively identified the single CCP management site confirmed to have groundwater impacted by CCP leachate. At this site, 9 genera (>0.5% relative abundance) were exclusive to CCP porewater and downgradient groundwater. Inferred metabolisms for these taxa indicates potential for N and S biogeochemical transformations and 1-C metabolism that are consistent with a reducing environment, as evidenced by low ORP and depleted SO 4 2− . This research contributes to a growing understanding of conditions where these data types, analyses, and interpretation methods could be applied for distinguishing influence from CCP on the surrounding environment, as well as practical limitations.

01 COAL, LIGNITE, AND PEAT↗