Search NASA⌕ Search

SEARCH · Search NASA

Results for “combustion chambers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1956

Effects of Variations in Combustion-chamber Configuration on Ignition Delay in a 50-pound-thrust Rocket

Ignition delays of a diallylaniline-triethylamine mixture and of triethyl trithioposphite with red fuming nitric acid were measured as a function of combustor dimensions, initial propellant temperature, and initial ambient pressure. Ignition delay increased with exhaust-nozzle diameter. Ignition delay also increased as propellant temperature decreased, but did not vary with initial ambient pressure except with the largest nozzle diameter. A correlation among ignition delay, combustor dimensions, and propellant temperature is presented, and the extension of the correlation to other systems is discussed.

Ladanyi, Dezso J↗
NASA NTRS1993

Combustion chamber analysis code

A three-dimensional, time dependent, Favre averaged, finite volume Navier-Stokes code has been developed to model compressible and incompressible flows (with and without chemical reactions) in liquid rocket engines. The code has a non-staggered formulation with generalized body-fitted-coordinates (BFC) capability. Higher order differencing methodologies such as MUSCL and Osher-Chakravarthy schemes are available. Turbulent flows can be modeled using any of the five turbulent models present in the code. A two-phase, two-liquid, Lagrangian spray model has been incorporated into the code. Chemical equilibrium and finite rate reaction models are available to model chemically reacting flows. The discrete ordinate method is used to model effects of thermal radiation. The code has been validated extensively against benchmark experimental data and has been applied to model flows in several propulsion system components of the SSME and the STME.

Przekwas, A. J.↗
NASA NTRS1993

Heat transfer in rocket combustion chambers

Complexities of liquid rocket engine heat transfer which involve the injector faceplate and film cooled walls are being investigated by computational analysis. A conjugate heat transfer analysis was used to describe localized heating phenomena associated with particular injector configurations and film coolant flows. These components were analyzed, and the analyses verified when appropriate test data were available. The component analyses are being synthesized into an overall flowfield/heat transfer model. A Navier-Stokes flow solver, the FDNS code, was used to make the analyses. Particular attention was given to the representation of the thermodynamic properties of the fluid streams. Unit flow models of specific coaxial injector elements have been developed and are being used to describe the flame structure near the injector faceplate.

Anderson, P.↗
NASA NTRS1998

Fastrac Rocket Engine Combustion Chamber Acoustic Cavities

A three dimensional modal analysis was performed using finite fluid elements. The analysis shows four distinct modes of the Fastrac chamber plus cavities near the frequency of the chamber first tangential mode. The mode shapes illustrate the complexity of fluid oscillations in a three dimensional chamber and acoustic cavity. In addition, a first tangential forcing function was applied to the chamber with three different acoustic cavity fluid temperatures. It was observed that the acoustic cavity fluid temperature has a significant effect on the response of the chamber to first tangential mode oscillations.

Christensen, Eric↗
NASA NTRS2001

Vacuum Plasma Spray of Cu-8Cr-4Nb for Advanced Liquid-Fuel Combustion Chambers

Vacuum plasma spray (VPS) formed Cu-8Cr-4Nb alloy, with low oxygen, exhibits higher strength at room and elevated temperature than material formed by extrusion. The VPS formed material exhibits slightly lower ductility than the extruded material. VPS forming of Cu-8Cr-4Nb can be used to produce near net structures with mechanical properties comparable to current extruded material.

Zimmerman, F.↗
NASA NTRS2001

A Fiber-Optic Probe Design for Combustion Chamber Flame Detection Applications-Design Criteria, Performance Specifications, and Fabrication Technique

This paper documents the design and development of the fiber-optic probes utilized in the flame detection systems used in NASA Langley Research Center's 8-Foot High Temperature Tunnel (8-ft HTT). Two independent flame detection systems are utilized to monitor the presence and stability of the main-burner and pilot-level flames during facility operation. Due to the harsh environment within the combustor, the successful development of a rugged and efficient fiber-optic probe was a critical milestone in the development of these flame detection systems. The final optical probe design for the two flame detection systems resulted from research that was conducted in Langley's 7-in High Temperature Pilot Tunnel (7-in HTT). A detailed description of the manufacturing process behind the optical probes used in the 8-ft HTT is provided in Appendix A of this report.

Borg, Stephen E.↗
NASA NTRS2005

Low Pressure Plasma Sprayed Overlay Coatings for GRCop-84 Combustion Chamber Liners for Reusable Launch Vehicles

An advanced Cu-8(at.%)Cr-4%Nb alloy developed at NASA's Glenn Research Center, and designated as GRCop-84, is currently being considered for use as combustor chamber liners and nozzle ramps in NASA s future generations of reusable launch vehicles (RLVs). However, past experience has shown that unprotected copper alloys undergo an environmental attack called "blanching" in rocket engines using liquid hydrogen as fuel and liquid oxygen as the oxidizer. Potential for sulfidation attack of the liners in hydrocarbon-fueled engines is also of concern. Protective overlay coatings alloys are being developed for GRCop-84. The development of this coatings technology has involved a combination of modeling, coatings development and characterization, and process optimization. Coatings have been low pressure plasma sprayed on GRCop-84 substrates of various geometries and shapes. Microstructural, mechanical property data and thermophysical results on the coated substrates are presented and discussed.

Raj, S. V.↗
NASA NTRS2018

Hybrid Additive Manufacturing Deposition and Selective Laser Melting Techniques Applied to Copper-Alloy Liquid Rocket Engine Combustion Chambers

Virgin Orbit and the NASA Marshall Space Flight Center have partnered to fabricate a small, multi-metallic, regeneratively cooled thrust chamber by leveraging the strengths of two different types of additive manufacturing: Direct Metal Laser Sintering (DMLS) for the copper alloy liner and blown powder Directed Energy Deposition (DED) for the Inconel structural jacket. The DED is being developed using Virgin Orbit's DMG Mori Seiki hybrid additive/subtractive machining center to further enable unique processing and further cost savings. The materials chosen are preferred for high performance thrust chamber applications, representing a significant advancement from the compromises typically made in the production of metal 3D printed thrust chambers for rocket engines. The 1.2K-lbf thrust article is a 16" tall, 3" diameter design modified for this effort to be regeneratively cooled with water and hot fired using a RP-1/LOX pintle-style development injector from Virgin Orbit's NewtonFour upper stage engine. The thrust chamber was tested at Virgin Orbit's Necker test site in Mojave, California. Results from this test campaign are reported in addition to information characterizing the liner, jacket, and bimetallic diffusion layer materials. This paper will also highlight some of the future bimetallic thrust chamber developments that MSFC and Virgin Orbit will complete under a recently awarded NASA contract.

Zagorski, Kevin↗
NASA NTRS2024

Dynamic Mechanical Analysis of Post-Cured Bismaleimide Resins for Composite-Overwrapped Combustion Chambers Cycled From Cryogenic to High Temperatures

In support of the Rapid Analysis and Manufacturing Propulsion Technology (RAMPT) project, samples made of polybismaleimide (BMI) resin were made and tested under cryogenic conditions. Neat resin samples were tested for multiple cycles, from high temperature (300°C) to cryogenic temperature (-150°C), to replicate the conditions a rocket engine assembly would experience in a test campaign and in operation. To increase the glass transition temperature (and thus mechanical stability), samples were exposed to different post-cure temperatures and were tested using a dynamic mechanical analysis (DMA) instrument. Consistent with expectations, the BMI samples post-cured at higher temperatures generally resulted in higher storage modulus under high temperature test conditions but at the expense of storage modulus values at low temperature test conditions.

Christopher Stelter↗