Search NASA⌕ Search

SEARCH · Search NASA

Results for “complex fluids”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Fluid-structure interactions in compressible cavity flows

Experiments were performed to understand the complex fluid-structure interactions that occur during aircraft internal store carriage. A cylindrical store was installed in a rectangular cavity having a length-to-depth ratio of 3.33 and a length-to-width ratio of 1. The Mach number ranged from 0.6 to 2.5 and the incoming boundary layer was turbulent. Fast-response pressure measurements provided aeroacoustic loading in the cavity, while triaxial accelerometers provided simultaneous store response. Despite occupying only 6% of the cavity volume, the store significantly altered the cavity acoustics. The store responded to the cavity flow at its natural structural frequencies, and it exhibited a directionally dependent response to cavity resonance. Specifically, cavity tones excited the store in the streamwise and wall-normal directions consistently, whereas a spanwise response was observed only occasionally. Also, the streamwise and wall-normal responses were attributed to the longitudinal pressure waves and shear layer vortices known to occur during cavity resonance. Although the spanwise response to cavity tones was limited, broadband pressure fluctuations resulted in significant spanwise accelerations at store natural frequencies. As a result, the largest vibrations occurred when a cavity tone matched a structural natural frequency, although energy was transferred more efficiently to natural frequencies having predominantly streamwise and wall-normal motions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Assessing the combined influence of fluid-rock interactions on reservoir properties and injectivity during CO 2 storage in saline aquifers

Complex fluid-rock interactions can occur during the injection of carbon dioxide (CO 2 ) into saline aquifers for sequestration, which may affect CO 2 injectivity and storage capacity. A comprehensive reactive transport model is established to analyze salt precipitation, CO 2 -water-rock geochemical reactions, and their effects on reservoir physical properties and injectivity. In addition, sensitivity analyses are conducted to investigate the main factors that affect fluid-rock interactions and injectivity with relevance for site selection for CO 2 storage. Results show that the back flow of formation water not only affects the salt precipitation but also affects the CO 2 -water-rock geochemical reactions, resulting in salt and calcite precipitations mainly occurring in the dry-out zone. However, most of the mineral dissolution/precipitation caused by CO 2 -water-rock reaction occurs in the two-phase and aqueous-phase zones, and their effect on reservoir porosity and permeability are small. A considerable amount of sodium chloride precipitates in the dry-out zone as brine is drawn by capillary action into this zone, with significant consequences for porosity, permeability and injectivity. The injection rate, salinity, capillary pressure–saturation relationships, and reservoir permeability strongly affect the distribution of salt precipitation. Finally, moderate injection rates, salinities, capillary pressures, and permeabilities all lead to favorable CO 2 injectivity.

54 ENVIRONMENTAL SCIENCES↗

Advanced Supercritical Carbon Dioxide Brayton Cycle Development

Fluids operating in the supercritical state have promising characteristics for future high efficiency power cycles. In order to develop power cycles using supercritical fluids, it is necessary to understand the flow characteristics of fluids under both supercritical and two-phase conditions. In this study, a Computational Fluid Dynamic (CFD) methodology was developed for supercritical fluids flowing through complex geometries. A real fluid property module was implemented to provide properties for different supercritical fluids. However, in each simulation case, there is only one species of fluid. As a result, the fluid property module provides properties for either supercritical CO 2 (S-CO 2 ) or supercritical water (SCW). The Homogeneous Equilibrium Model (HEM) was employed to model the two-phase flow. HEM assumes two phases have same velocity, pressure, and temperature, making it only applicable for the dilute dispersed two-phase flow situation. Three example geometries, including orifices, labyrinth seals, and valves, were used to validate this methodology with experimental data. For the first geometry, S-CO 2 and SCW flowing through orifices were simulated and compared with experimental data. The maximum difference between the mass flow rate predictions and experimental measurements is less than 5%. This is a significant improvement as previous works can only guarantee 10% error. In this research, several efforts were made to help this improvement. First, an accurate real fluid module was used to provide properties. Second, the upstream condition was determined by pressure and density, which determines supercritical states more precise than using pressure and temperature. For the second geometry, the flow through labyrinth seals was studied. After a successful validation, parametric studies were performed to study geometric effects on the leakage rate. Based on these parametric studies, an optimum design strategy for the see-through labyrinth seals was proposed. A stepped labyrinth seal, which mimics the behavior of the labyrinth seal used in the Sandia National Laboratory (SNL) S-CO 2 Brayton cycle, was also tested in the experiment along with simulations performed. The rest of this study demonstrates the difference of valves' behavior under supercritical fluid and normal fluid conditions. A small-scale valve was tested in the experiment facility using S-CO 2 . Different percentages of opening valves were tested, and the measured mass flow rate agreed with simulation predictions. Two transients from a real S-CO 2 Brayton cycle design provided the data for valve selection. The selected valve was studied using numerical simulation, as experimental data is not available.

42 ENGINEERING↗

An Anisotropic Fluid-Solid Model of the Mouse Heart

A critical challenge in biomechanical simulations is the spatial discretization of complex fluid-solid geometries created from imaging. This is especially important when dealing with Lagrangian interfaces, as there must be at a minimum both geometric and topological compatibility between fluid and solid phases, with exact matching of the interfacial nodes being highly desirable. We have developed a solution to this problem and applied the approach to the creation of a 3D fluidsolid mesh of the mouse heart. First, a 50 micron isotropic MRI dataset of a perfusion-fixed mouse heart was segmented into blood, tissue, and background using a customized multimaterial connected fuzzy thresholding algorithm. Then, a multimaterial marching cubes algorithm was applied to produce two compatible isosurfaces, one for the blood-tissue boundary and one for the tissue-background boundary. A multimaterial smoothing algorithm that rigorously conserves volume for each phase simultaneously smoothed the isosurfaces. Next we applied novel automated meshing algorithms to generate anisotropic hybrid meshes with the number of layers and the desired element anisotropy for each material as the only input parameters. As the meshes are scale-invariant within a material and include boundary layer prisms, fluid-structure interaction computations would have a relative error equilibrated over the entire mesh. The resulting model is highly detailed mesh representation of the mouse heart, including features such as chordae and coronary vasculature, that is also maximally efficient to produce the best simulation results for the computational resources available

59 BASIC BIOLOGICAL SCIENCES↗

Theory of Brownian motion in a Jeffreys fluid

We have constructed a kinetic theory of Brownian motion in a rheologically complex medium-a Jeffreys fluid that is characterized by a combination of two viscosity mechanisms: ordinary and delayed. This model is shown to be much better suited for the interpretation of experiments on the microrheology of viscoelastic media than the standard Maxwell model. In particular, no oscillations of the mean-square particle displacement arise in a Jeffreys fluid, which is a nonremovable artifact of the theory of Brownian motion in a Maxwell fluid. The developed approach can to be used also consider the diffusion of particles in other complex fluids whose rheology is described by phenomenological schemes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Generating a heated fluid using an electromagnetic radiation-absorbing complex

A vessel including a concentrator configured to concentrate electromagnetic (EM) radiation received from an EM radiation source and a complex configured to absorb EM radiation to generate heat. The vessel is configured to receive a cool fluid from the cool fluid source, concentrate the EM radiation using the concentrator, apply the EM radiation to the complex, and transform, using the heat generated by the complex, the cool fluid to the heated fluid. The complex is at least one of consisting of copper nanoparticles, copper oxide nanoparticles, nanoshells, nanorods, carbon moieties, encapsulated nanoshells, encapsulated nanoparticles, and branched nanostructures. Further, the EM radiation is at least one of EM radiation in an ultraviolet region of an electromagnetic spectrum, in a visible region of the electromagnetic spectrum, and in an infrared region of the electromagnetic spectrum.

36 MATERIALS SCIENCE↗

Self-assembly of {alpha}-helical polypeptides driven by complex coacervation.

Reported is the ability of alpha-helical polypeptides to self-assemble with oppositely-charged polypeptides to form liquid complexes while maintaining their alpha-helical secondary structure. Coupling the alpha-helical polypeptide to a neutral, hydrophilic polymer and subsequent complexation enables the formation of nanoscale coacervate-core micelles. While previous reports on polypeptide complexation demonstrated a critical dependence of the nature of the complex (liquid versus solid) on chirality, the alpha-helical structure of the positively charged polypeptide prevents the formation of beta-sheets, which would otherwise drive the assembly into a solid state, thereby, enabling coacervate formation between two chiral components. The higher charge density of the assembly, a result of the folding of the alpha-helical polypeptide, provides enhanced resistance to salts known to inhibit polypeptide complexation. The unique combination of properties of these materials can enhance the known potential of fluid polypeptide complexes for delivery of biologically relevant molecules.

chirality↗

Room-temperature polariton quantum fluids in halide perovskites

Abstract Quantum fluids exhibit quantum mechanical effects at the macroscopic level, which contrast strongly with classical fluids. Gain-dissipative solid-state exciton-polaritons systems are promising emulation platforms for complex quantum fluid studies at elevated temperatures. Recently, halide perovskite polariton systems have emerged as materials with distinctive advantages over other room-temperature systems for future studies of topological physics, non-Abelian gauge fields, and spin-orbit interactions. However, the demonstration of nonlinear quantum hydrodynamics, such as superfluidity and Čerenkov flow, which is a consequence of the renormalized elementary excitation spectrum, remains elusive in halide perovskites. Here, using homogenous halide perovskites single crystals, we report, in both one- and two-dimensional cases, the complete set of quantum fluid phase transitions from normal classical fluids to scatterless polariton superfluids and supersonic fluids—all at room temperature, clear consequences of the Landau criterion. Specifically, the supersonic Čerenkov wave pattern was observed at room temperature. The experimental results are also in quantitative agreement with theoretical predictions from the dissipative Gross-Pitaevskii equation. Our results set the stage for exploring the rich non-equilibrium quantum fluid many-body physics at room temperature and also pave the way for important polaritonic device applications.

42 ENGINEERING↗

Multi-dimensional rheology-based two-phase model for sediment transport and applications to sheet flow and pipeline scour

Sediment transport is fundamentally a two-phase phenomenon involving fluid and sediments; however, many existing numerical models are one-phase approaches, which are unable to capture the complex fluid-particle and inter-particle interactions. In the last decade, two-phase models have gained traction; however, there are still many limitations in these models. For example, several existing two-phase models are confined to one-dimensional problems; in addition, the existing two-dimensional models simulate only the region outside the sand bed. This paper develops a new three-dimensional two-phase model for simulating sediment transport in the sheet flow condition, incorporating recently published rheological characteristics of sediments. The enduring-contact, inertial, and fluid viscosity effects are considered in determining sediment pressure and stresses, enabling the model to be applicable to a wide range of particle Reynolds number. A k − ε turbulence model is adopted to compute the Reynolds stresses. In addition, a novel numerical scheme is proposed, thus avoiding numerical instability caused by high sediment concentration and allowing the sediment dynamics to be computed both within and outside the sand bed. The present model is applied to two classical problems, namely, sheet flow and scour under a pipeline with favorable results. For sheet flow, the computed velocity is consistent with measured data reported in the literature. For pipeline scour, the computed scour rate beneath the pipeline agrees with previous experimental observations. However, the present model is unable to capture vortex shedding; consequently, the sediment deposition behind the pipeline is overestimated. Sensitivity analyses reveal that model parameters associated with turbulence have strong influence on the computed results.

42 ENGINEERING↗

Ring Model Development and Validation for Prismatic HTGR Core Thermal-hydraulics and Safety Analysis

Because of the complex core geometry, prismatic high temperature gas-cooled reactors (prismatic HTGRs) often exhibit complex thermal fluid behaviors during both normal operating and transient conditions. Most HTGR designs rely on passive safety system for decay heat removal, such as the reactor cavity cooling system (RCCS). During postulated accidents like Pressurized Conduction Cooldown (PCC) event, the decay heat is first radially transferred from the core region to the reactor vessel outer surface, then to the RCCS cooling panels. The peak fuel temperature is controlled by heat transfer mechanisms with two distinctive characteristic length scales, i.e., the core-wise effective heat conduction and local heat conduction in the fuel pellet scale. As both length scales are essential to determine the fuel temperature, from the modeling perspective, computer codes must be able to capture heat transfer in both scales. This is challenging for both computational fluid dynamics (CFD) tools because of extremely large amount of computation resources required, and for system analysis codes because of the challenge to model the complex core geometry. Under the support of DOE-NE’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, efforts have been pursued to support HTGR technology development and its modeling and simulation needs. There is a particular need for advanced modeling and simulation tools to predict thermal-fluid behavior during safety-related transients. In our previous studies, the ring model was adopted in SAM and further developed to simulate the normal operating condition and a PCC event using the MHTGR-350 design of General Atomics as the reference design. This current work represents a continuation of these previous efforts, and the focus is to critically review and examine simplifications and assumptions made to develop the ring model, and to perform code validation using experimental data from an integral-effect test facility, the High Temperature Test Facility (HTTF) at the Oregon State University. In this study, the test PG-27 from the HTTF test suite was selected for code validation purpose. The test PG-27 is a transient test designed to simulate the PCC event of the MHTGR design. Very good agreements between SAM prediction and experimental measurements were found in both coolant and solid structure temperatures during the transient.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Application of parallel distributed Lagrange multiplier technique to simulate coupled Fluid-Granular flows in pipes with varying Cross-Sectional area

Fluid-granular flows are common phenomena in nature and industry. Here, an efficient computational technique based on the distributed Lagrange multiplier method is utilized to simulate complex fluid-granular flows. Each particle is explicitly resolved on an Eulerian grid as a separate domain, using solid volume fractions. The fluid equations are solved through the entire computational domain, however, Lagrange multiplier constrains are applied inside the particle domain such that the fluid within any volume associated with a solid particle moves as an incompressible rigid body. The particle–particle interactions are implemented using explicit force-displacement interactions for frictional inelastic particles similar to the DEM method with some modifications using the volume of an overlapping region as an input to the contact forces. Here, a parallel implementation of the method is based on the SAMRAI (Structured Adaptive Mesh Refinement Application Infrastructure) library.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Integration of APECS and VE-Suite for Data Overlay

In the design of advanced power generation facilities, process simulation tools are being utilized to model plant behavior and quickly analyze results. While such tools enable investigation of crucial aspects of plant design, typical commercial process simulators still do not explore some plant design information, including high-fidelity data from computational fluid dynamics (CFD) models of complex thermal and fluid flow phenomena, economics data used for policy decisions, operational data after the plant is constructed, and as-built information for use in as-designed models. Software tools must be created that allow disparate sources of information to be integrated for facilitating accurate and effective plant design. At the Department of Energy’s (DOE) National Energy Technology Laboratory (NETL), the Advanced Process Engineering Co-Simulator (APECS) has been developed as an integrated software suite that combines process simulation (e.g., Aspen Plus®) and high-fidelity equipment simulation (e.g., FLUENT®). In this paper, the integration of the high-fidelity CFD data with overall process data in a virtual power simulation environment will be described. More specifically, we will highlight VE-Suite, an open-source virtual engineering (VE) software toolkit, and its support of Aspen Plus® Hierarchy blocks via the VE-AspenUnit.

01 COAL, LIGNITE, AND PEAT↗

Designing and transforming yield-stress fluids

We review progress in designing and transforming multi-functional yield-stress fluids and give a perspective on the current state of knowledge that supports each step in the design process. We focus mainly on the rheological properties that make yield-stress fluids so useful and the trade-offs which need to be considered when working with these materials. Thinking in terms of "design with" and "design of' yield-stress fluids motivates how we can organize our scientific understanding of this field. "Design with" involves identification of rheological property requirements independent of the chemical formulation, e.g. for 3D direct-write printing which needs to accommodate a wide range of chemistry and material structures. "Design of includes microstructural considerations: conceptual models relating formulation to properties, quantitative models of formulation-structureproperty relations, and chemical transformation strategies for converting effective yield-stress fluids to be more useful solid engineering materials. Finally, future research directions are suggested at the intersection of chemistry, soft-matter physics, and material science in the context of our desire to design useful Theologically-complex functional materials.

36 MATERIALS SCIENCE↗

Molecular speciation controls arsenic and lead bioaccessibility in fugitive dusts from sulfidic mine tailings

Communities nearby mine wastes in arid and semi-arid regions are potentially exposed to high concentrations of toxic metal(loid)s from fugitive dusts deriving from impoundments. To assess the relation between potentially lofted particles and human health risk, we studied the relationship between pharmacokinetic bioaccessibility and metal(loid) molecular speciation for mine tailings dust particulate matter (PM), with elevated levels of arsenic and lead (up to 59 and 34 mmol kg -1 , respectively), by coupling in vitro bioassay (IVBA) with X-ray absorption spectroscopy (XAS). Mine tailing efflorescent salts (PM ES ) and PM from the surface crust (0–1 cm, PM SC ) and near surface (0–25 cm) were isolated to <10 μm and <150 μm effective spherical diameter (PM 10 and PM 150 ) and reacted with synthetic gastric and lung fluid for 30 s to 100 h to investigate toxic metal(loid) release kinetics. Bioaccessible (BAc) fractions of arsenic and lead were about 10 and 100 times greater in gastric than in lung fluid simulant, respectively, and 10–100% of the maximum gastric BAc from PM 10 and PM 150 occurred within 30 s, with parabolic dissolution of fine, highly-reactive particles followed by slower release from less soluble sources. Evaporite salts were almost completely solubilized in gastric-fluid simulants. Arsenate within jarosite and sorbed to ferrihydrite, and lead from anglesite, were identified by XAS as the principal contaminant sources in the near surface tailings. In the synthetic lung fluid, arsenic was released continuously to 100 h, suggesting that residence time in vivo must be considered for risk determination. Analysis of pre- and post-IVBA PM indicated the release of arsenic in lung fluid was principally from arsenic-substituted jarosite, whereas in synthetic gastric fluid arsenic complexed on ferrihydrite surfaces was preferentially released and subsequently repartitioned to jarosite-like coordination at extended exposures. Lead dissolved at 30 s was subsequently repartitioned back to the solid phase as pyromorphite in phosphate rich lung fluid. The bioaccessibility of lead in surface tailings PM was limited due to robust sequestration in plumbojarosite. Kinetic release of toxic elements in both synthetic biofluids indicated that a single IVBA interval may not adequately describe release dynamics.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗

Phase-field modeling of rate-dependent fluid-driven fracture initiation and propagation

The rate-dependent behavior associated with deformation and fracturing of materials, such as natural rocks, poses significant challenges for modeling. In addition to the complications of the viscoelastic response, the speed of fracture propagation reflects micromechanical mechanisms in the fracture process zone(FPZ). In order to represent these complicated behaviors, a thermodynamically consistent, rate-dependent fracture model is required. Based on rigorous thermodynamic principles, we derive a rate-dependent phase-field mechanical model coupled with single-phase fluid flow in both the matrix and the fracture. The model is guaranteed to satisfy energy conservation during fracture propagation. Here, the system of equations is solved using the introduced solution procedure and a novel preconditioner that accounts for the complex fluid-structure interaction. The proposed phase-field model is tested against several benchmark problems on solid-fluid coupling, fluid-driven fracture propagation and rate-dependent viscoelastic deformation. The model serves as a strong basis for investigating rate-dependent fracturing experiments and for making predictions of material behaviors under new conditions.

42 ENGINEERING↗

Hyperuniform Active Chiral Fluids with Tunable Internal Structure

Large density fluctuations observed in active systems and hyperuniformity are two seemingly incompatible phenomena. However, the formation of hyperuniform states has been recently predicted in nonequilibrium fluids formed by chiral particles performing circular motion with the same handedness. In this work, we report evidence of hyperuniformity realized in a chiral active fluid comprised of pear-shaped Quincke rollers of arbitrary handedness. We show that hyperunifonnity and large density fluctuations, triggered by dynamic clustering, coexist in this system at different length scales. The system loses its hyperuniformity as the curvature of particles' motion increases, transforming them into localized spinners. Our results experimentally demonstrate a novel hyperuniform active fluid and provide new insights into an interplay between chirality, activity, and hyperuniformity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Critical analysis of velocimetry methods for particulate flows from synthetic data

Particle tracking methods that extract high-fidelity particle velocity data from high speed video of particle laden flows is a common experimental technique applied to chemical processes. These measurements are used to better understand the motion of particles and fluids in complex systems and create data against which computational models are validated. However, the methods, codes, and experimental setups all have limitations. It is imperative that practitioners verify the methods and their implementation as well as understand the limitations of experimental setups. This work focuses on quantifying the visible depth of field in a high particle concentration fluidized bed. Following a precedent set by the particle imaging velocimetry community, a particle velocity field is manufactured using a computational fluid dynamics and discrete element method simulation. Photo realistic high-speed videos are rendered based on the simulated data using the three-dimensional creation software Blender. Particle velocities are extracted from the synthetic high-speed videos using three variants of Particle Tracking Velocimetry and Optical Flow Velocimetry methodologies. Here, the tracked results are then compared to the known solution, quantifying the error associated with the assumed visible depth. The results indicate that at depth of one particle diameter, all three particle tracking codes give accurate measurements, largely within 5%. However, the error increases when the full bed video measurements are compared to the known solution at one particle diameter, i.e., mimicking a validation study. Finally, for some statistics the constant depth assumption only increases the error slightly, for others significantly.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗