Search NASA⌕ Search

SEARCH · Search NASA

Results for “composition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Aqueous solution-based synthesis approach for carbon-disordered rocksalt composite cathode development and its limitations

Disordered rocksalt cathodes exhibit high specific capacities and high energy density; however, their low electronic conductivity poses a great challenge. Herein, we explored an aqueous-solution-based synthesis route that involves controlling the surface charges of Li 1.2 Mn 0.6 Ti 0.2 O 1.8 F 0.2 (LMTOF) to be anchored by a few-layer reduced graphene oxide (rGO) for the first time. The uniform rGO wrapping on the surface of the LMTOF particles is achieved by electrostatic attraction between the negatively charged rGO and positively charged LMTOF particles. Although the initial specific capacity of rGO-LMTOF composite increased by 58 % compared to the pristine LMTOF, the composite experienced a severe capacity fade over cycling. The synthesis process in an aqueous medium resulted in Li + /H + exchange and TM dissolution as evidenced from inductively coupled plasmon analysis and X-ray diffraction analysis. Therefore, this work suggests the search for alternative media or conditions for the synthesis of carbon-disordered rock salt cathode composite.

25 ENERGY STORAGE↗

The composition of gases from a diffusion flame above longleaf pine needle fuel beds

The gas and tar composition of a diffusion flame from longleaf pine needles is currently poorly understood and more data are needed to fill in the gap between pyrolysis data and smoke plume data, thus improving physical and chemical modeling of wildland smoke formation. A pilot experiment to measure light gas and tar composition of such a flame is described for three flame regions: persistent flame (flame base), intermittent flame, and smoke plume. Flame gases from 24 experimental fires were collected in canisters and analyzed using EPA method TO-14A for CO 2 , CO, H 2 , CH 4 , and C 2 to C 7 hydrocarbon gases. Condensed gas (tar) samples were collected and analyzed using GC/MS. Other light gases were measured using FTIR spectroscopy. Results from compositional data analysis suggest significant differences in (relative) concentration of compounds detected in the three regions of the flame. Statistical tests for differences in flame zones were performed using the canister data: Concentration of hydrocarbons relative to CO and CO 2 decreased from the persistent flame zone above the pyrolyzing needles through the intermittent flame region into the flame-free plume. This was likely due to both chemical reactions (oxidation) occurring in the flame as well as the introduction of air into the flame/plume by entrainment.

Biomass↗

Effect of metal-free mesoporous silica incorporated ZSM-5 composite on thermo-catalytic pyrolysis of polypropylene

Although different zeolites impregnated with transition metals have been used in catalytic deconstruction of waste plastics to other products, the influence of hierarchical structures on conversion and product selectivity in plastic upcycling has not been thoroughly investigated. This research explores a transition metal free zeolite-based hierarchical composite, synthesized by incorporating SBA-15 in ZSM-5 framework, for efficient thermos-catalytic upcycling of polypropylene (PP). Thermogravimetric analysis reveals that ZSM-5@SBA-15 can break down PP at a significantly lower temperature, 240 °C, compared to that of pristine PP using ZSM-5 or SBA-15. In addition, pyrolysis of PP at 400 °C using ZSM-5@SBA-15 composite outperforms ZSM-5 or SBA-15 used separately and yields 90 % conversion with 70 % selectivity to propene. The presence of mesopores in the catalyst appears to reduce the diffusion resistance of intermediate products for successive scission, thereby reducing the activation energy of reaction and improving catalytic activity. In conclusion, the hierarchical composite ZSM-5@SBA-15 has significant potential for upcycling of PP into valuable monomers and lighter olefins, with lower energy demands, enhancing the economic feasibility of the process.

ZSM-5@SBA-15↗

Advanced polymer impregnation and pyrolysis (PIP) of SiOC-based ceramic matrix composites (CMCs)

Silicon carbide (SiC) ceramic matrix composites (CMCs) are valued for their high-temperature properties, making them ideal for harsh environments. However, conventional polymer impregnation and pyrolysis (C-PIP) often result in porous composites and require numerous cycles for densification. This study introduces the advanced PIP (A-PIP) method using a crosslinked polycarbosiloxane (PCS) precursor to enhance densification efficiency. Five SiC CMCs were fabricated using C-PIP and A-PIP, with variations in fiber reinforcement and fiber coatings. A-PIP achieved up to 19 % higher density and 78 % lower porosity in 79–86 % less processing time compared to C-PIP. Moreover, SiC-SiOC composites with boron nitride-coated fibers showed significant improvements in tensile strength (11 MPa to 134 MPa) and strain at maximum strength (0.01–0.11 %), underscoring the role of weak fiber-matrix interfaces. In conclusion, these results demonstrate A-PIP's potential to produce dense, low-porosity SiC CMCs more efficiently, significantly reducing manufacturing time and costs.

36 MATERIALS SCIENCE↗

Radiation-induced bowing of SiC/SiC composites under neutron flux gradients—integral experimental data for model validation

Here, the radiation-induced swelling of SiC and its composites, including strong dependencies on temperature and dose, can drive significant lateral bowing in the presence of temperature and/or dose gradients. In recent years, simulations have been performed to assess the extent of bowing in SiC composite light-water reactor (LWR) fuel cladding and boiling water reactor (BWR) channel boxes. However, to date, no integral experimental data exist to validate these models. This work provides the first experimental bowing evaluation of three ∼380 mm long SiC composite specimens irradiated under varying neutron dose gradients (∼50°C–60°C, 0.03–0.06 dpa): two tubes (∼9.8 mm diameter) and a miniature BWR channel box (∼30 mm square). The measured radiation-induced length swelling (∼0.3%–0.7% linear) was consistently 10%–21% higher than values obtained from 3D finite element structural analyses with inputs from 3D radiation transport calculations. This discrepancy could be at least partially explained by differences in dose rate (∼10 -8 dpa/s) compared to the literature data (∼10-6 dpa/s) used to establish the dose-to-swelling correlations in the model. Nevertheless, the modeled bowing magnitudes (<2 mm) obtained from finite element analyses and simple analytical equations were within the bounds of the experimental measurements for all specimens. With improved confidence in the ability to predict the structural response and measure the macroscopic deformations, future experiments will target transient bowing under neutron flux gradients at representative LWR temperatures and assess whether grid spacers can mitigate the tens of millimeters of bowing that would otherwise be expected in ∼4 m long LWR components.

bowing↗

Composite biopolymer electrolytes for high-performance reversible zinc-air batteries

Zinc-air batteries (ZABs) are regarded as one of the most promising candidates for next-generation energy storage systems due to their inherent safety, high energy density, and low cost. In this study, we optimized the composition of gel polymer electrolytes (GPEs), which play a crucial role in enhancing ZAB reversibility due to their water retention capabilities. The GPEs are synthesized using a combination of polyacrylic acid (PAA), polyacrylamide (PAM), and biopolymer kappa-carrageenan (KC), with and without additional additives. Among these, the composite GPE containing KC, PAA, and PAM demonstrated superior ionic conductivity (6.68 mS/cm at 30 °C) and enhanced water retention compared to the PAA–PAM-based GPE. Furthermore, this composite electrolyte operates within a wider electrochemical window of −1.0 V–2.2 V. A bifunctional catalyst, nickel–iron layered double hydroxide (NiFe-LDH), is electrochemically synthesized on a modified activated carbon cloth (CC). The catalyst loading is optimized based on oxygen evolution reaction (OER) performance, showing an overpotential of 555 mV. The oxygen reduction reaction (ORR) occurred at a half-wave potential of 0.620 V, which is lower than that of Pt/C (0.852 V), indicating better catalytic activity. The KC based cell exhibit better cycling stability than PAA–PAM-based GPE. The electrochemical performance of ZAB cells is evaluated under various atmospheres: ambient air and humid conditions and temperatures. Notably, in a humid environment, the cells achieved extended cycling stability, operating for over 500 h—significantly longer than under open-air conditions. Overall, this study highlights the importance of tailored GPE design and efficient bifunctional catalysts to enhance the performance and longevity of zinc-air batteries for long-duration energy storage applications.

Catalyst↗

Boron Nitride-Driven Strengthening of Aluminum Composites via Friction Stir Processing

Friction stir welding and processing (FSW/P) has emerged as an effective solid-state joining technique for fabricating metal matrix composites (MMCs), offering improved mechanical properties through refined microstructural evolution. In this study, an aluminum-boron nitride nanoparticle (Al-BNNP) composite was synthesized via FSW, and its indentation-based mechanical properties were systematically evaluated. Microhardness mapping across the weld cross-section revealed a progressive increase in hardness toward the stir zone (SZ), attributed to severe plastic deformation, dynamic recrystallization (DRX), and the reinforcing effect of BNNPs. Profilometry-based indentation plastometry (PIP) inferred yield strength (YS) demonstrates a 47.8% increase compared to the base metal (BM) and a 75% improvement compared to FSP pure aluminum reported in literature. This enhancement is attributed to strengthening mechanisms, including grain boundary pinning, load transfer, and increased dislocation density. The strain rate sensitivity (SRS) measurements at the nanoscale demonstrated a substantial decrease in the SZ, correlated with ultrafine grain structures and strong BNNP-matrix interactions. Activation volume analysis revealed a significant reduction in the SZ, suggesting that dislocation motion is increasingly restricted by dislocation-dislocation and dislocation-particle interactions. These findings suggest that incorporating BNNPs in FSW/P enables tailoring the microstructure without thermal degradation of the secondary particles, thereby significantly enhancing the mechanical performance of aluminum composites, particularly for structural applications in aerospace and automotive industries.

Aluminum↗

Evaluating Fracture Behavior of Bioinspired Alumina-YSZ Composites through Static and Dynamic Mechanical Testing

Ceramic materials are known for their high hardness and strength but are limited by low toughness and sudden failure. Inspired by the microstructure of dental enamel, which features undulating rods that promote crack deflection and energy absorption, architected specimens were designed and manufactured. A bespoke ball-on-ring (BoR) testing apparatus measured the static biaxial rupture strength of these bioinspired materials. Additionally, impact testing with spherical steel projectiles assessed their behavior under dynamic conditions. Monolithic alumina specimens were compared to architected alumina reinforced with yttria-stabilized zirconia (YSZ) rods produced via direct ink write 3D printing. BoR tests revealed that monolithic alumina had a Weibull modulus of 10.53 and a characteristic strength of 372.3 MPa, while the composite specimens showed a Weibull modulus of 5.46 and a characteristic strength of 213.3 MPa. Although the composite failed at lower stresses and projectile velocities, it exhibited notable crack deflection and fracture resistance, with cracks being effectively interrupted by the rod inclusions. The composite specimens also resulted in fewer and larger fragments upon impact. Finite element simulations confirmed the effectiveness of the rod structures in enhancing fracture resistance.

Bioinspired materials↗

Czochralski Growth and Characterization of a Compositionally Complex Rare Earth Aluminum Garnet Scintillator: (Gd 1/4 Y 1/4 Tb 1/4 Lu 1/4 ) 3 Al 5 O 12 :Ce

Compositionally complex oxides have garnered increasing interest for their enhanced phase stability and tunable functional properties, yet their development as bulk single crystal scintillators remains limited. Herein, we report the Czochralski growth and characterization of (Gd 1/4 Y 1/4 Tb 1/4 Lu 1/4 ) 3 Al 5 O 12 :Ce (GYTLAG), a compositionally complex garnet incorporating four dodecahedrally coordinated principal rare earth elements. The garnet phase was confirmed by powder and single crystal X-ray diffraction, and macroscopic defects are described. X-ray absorption near-edge structure measurements confirm the 3+ oxidation state of all rare earths and support their occupation of the same crystallographic site; white line intensity variations correlate with the anticipated segregation behavior. Elemental segregation is quantified by SEM/EDS and ICP-OES, and a linear trend was established between the segregation coefficient and the difference between each rare earth’s ionic radius (r) and the average ionic radius (AIR) of the dodecahedral site. This trend offers a predictive framework for compositional control in future REAG crystals grown by the Czochralski method. Photoluminescence and radioluminescence measurements reveal both Ce 3+ and Tb 3+ emission. Scintillation pulses exhibit four-component decay with dominant ~230 µs and ~1.2 ms components, and the light yield is estimated to be up to 43,000 ph/MeV under 137Cs γ-ray excitation. GYTLAG also demonstrates a strong radioluminescence efficiency and 50% lower afterglow at 20 ms compared to a LuAG:Ce reference, underscoring its promise for scintillator applications.

Compositionally complex oxide, high entropy oxide,↗

Control of Excitonic Energy Transfer in RGB Quantum Dot:Polymer Composites for Tunable White Emission

Tint-controlled white light is crucial for both illumination systems and display applications. Here, in this study, we demonstrate solution-processed quantum-dot light-emitting diodes (QD-LEDs) featuring a red–green–blue (RGB) QD–poly(methyl methacrylate) (PMMA) composite emissive layer (EML) for tunable white electroluminescence (EL). In this composite EML, PMMA functions as a dispersion matrix that modulates the interdot spacing (d), thereby controlling Förster resonance energy transfer (FRET) between QDs. By adjustment of the PMMA content, the balance of R, G, and B emissions is controlled, enabling systematic and continuous tuning of the EL color from greenish to reddish white at a fixed RGB ratio and constant driving bias. Time-resolved photoluminescence measurements confirm that the variation in the exciton lifetime with the PMMA fraction is the primary factor for tuning the EL color. Notably, nearly pure white EL with CIE coordinates close to (0.33, 0.33) is achieved using a diluted PMMA matrix without significant degradation of the electrical properties. Our results demonstrate d as an independent design parameter for decoupling color tuning from RGB composition and electrical operation, providing a versatile design framework for high-quality white- or tint-controlled QD-LEDs toward advanced solid-state lighting and display technologies.

36 MATERIALS SCIENCE↗

Self-Heating Conductive Ceramic Composites for High Temperature Thermal Energy Storage

The absence of affordable and deployable large-scale energy storage poses a major barrier to providing zero-emission energy on demand for societal decarbonization. High temperature thermal energy storage is one promising option with low cost and high scalability, but it is hindered by the inherent complexity of simultaneously satisfying all of the material requirements. Here we design a class of ceramic–carbon composites based on co-optimizing mechanical, electrical, and thermal properties. Further, these composites demonstrate stability in soak-and-hold tests and direct self-heating up to 1,936 °C and 750 thermal cycles from 500 to 1,630 °C without degradation. This thermal performance derives from their composition and microstructural design as verified by in situ high-temperature transmission electron microscopy and X-ray diffraction. They offer both higher energy density and lower cost than conventional storage technologies with a projected system Levelized Cost of Storage below the U.S. Department of Energy’s 2030 target 5 ¢/kWh (electric).

25 ENERGY STORAGE↗

Operando Optical Microscopy for Visualization of Dendrite Growth in an Argyrodite LPSCl–Polymer Composite Electrolyte

Herein, we demonstrate the utility of optical microscopy as an accessible technique for the in situ visualization of dendrite growth within polymer–sulfide composite solid-state electrolytes. The composite electrolyte features in situ polymerization and cross-linking of the polymer between ceramic particles, which opens up extensive opportunities for accelerated materials discovery, given the vast array of acrylate/methacrylate monomers available. Specifically, the cross-linked polymer poly(triethylene glycol dimethacrylate) (poly(TEGDMA)) was observed to effectively fill pores and inhibit dendrite growth at the lithium metal interface, attributed to its glassy state at room temperature. This work represents the first application of optical microscopy to illustrate that the incorporation of glassy, undoped polymers such as poly(TEGDMA) can serve as a viable strategy for dendrite suppression in solid-state composite electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-resolution national mapping of natural gas composition substantially updates methane leakage impacts

Methane is emitted from oil and gas operations alongside heavier hydrocarbons and non-hydrocarbon gases, shaping emissions management decision-making, including air quality impacts. Yet, most assessments assume fixed gas composition, overlooking significant spatial and temporal variations. Here, we generate a high-resolution, data-driven map of natural gas composition across the United States, reconstructing methane, heavier hydrocarbons, and non-hydrocarbon species using spatio-temporal interpolation and oil-and-gas production patterns. Our approach is able to reduce composition prediction errors by 39% in terms of Mean Absolute Error (MAE) compared to standard techniques and reveals that methane loss rates have been underestimated by more than 50% in some regions. Beyond methane, we uncover substantial variability in co-emitted gases, exposing blind spots in current emissions inventories and emissions management frameworks. Our work enables more accurate emissions assessments, guides targeted measurement strategies, and informs emissions management decision-making. It also provides a general framework for prediction in environmental applications that integrate sparse measurements with auxiliary variables.

03 NATURAL GAS↗

Tough and circular glass fiber composites via a tailored dynamic boronic ester interface

Glass fiber reinforced polymer (GFRP) composites are valued for their strength and cost-effectiveness. However, traditional GFRPs often face challenges for end-of-life recycling due to their non-depolymerizable thermoset matrices, and long-term performance due to inadequate interfacial adhesion, which can lead to fiber–matrix delamination. Here, in this work, we have designed dynamic fiber–matrix interfaces to allow tough and closed-loop recyclable GFRPs by utilizing a vitrimer, derived from upcycled polystyrene-b-poly(ethylene-co-butylene)-b-polystyrene (SEBS) with boronic ester (S-Bpin) and amine-based diol crosslinker. The boronic ester groups in S-Bpin form dynamic covalent bonds with the naturally present hydroxyl groups on the unsized GF surface, which eliminates the need for fiber sizing and enables facile closed-loop recyclability of both the fibers and the vitrimer matrix. The resulting strong fiber–matrix interface, depicted by the Raman mapping, leads to a 552% increase in-plane shear toughness (6.2 ± 0.3 MJ m -3 ) and 27% ultimate tensile strength (361 ± 89.2 MPa) compared to those of the conventional epoxy-based matrix (0.95 ± 0.05 MJ m -3 and 264 ± 59.7 MPa, respectively). The network rearrangement through dynamic boronic ester exchange enables fast thermoformability and repairability of micro-cracks at elevated temperatures. Additionally, both the matrix and composite demonstrate strong adhesion to various surfaces including steel and glasses exhibiting ≥6 MPa lap shear strength, which expands their suitability for diverse industrial applications. The readily created dynamic interface between boronic ester functionalized vitrimer and neat GFs presents a promising strategy for developing closed-loop recyclable, multifunctional structural materials, offering a sustainable alternative to non-recyclable thermoset GFRPs and contributes to a circular economy in composite materials.

36 MATERIALS SCIENCE↗

Modeling household-level party composition behavior for multiparty activities: a random parameter nested logit modeling approach

This study presents findings of a household-level party composition model for multiparty activities. It exploits data from a comprehensive Household Travel Survey conducted by Chicago Metropolitan Agency of Planning. The study estimates a random parameter nested logit model to capture households’ unobserved preference heterogeneity and non-proportional substitution patterns in terms of activity party composition for multiparty activities. A wide variety of household demographics, activity attributes and residential neighborhood characteristics are examined in this paper. The magnitude of the impacts of the determinants are tested in this study by analyzing the elasticity of the variables, which suggests that household demographics and attributes of the multiparty activities have significant effects on the household-level activity party composition. Residential neighborhood characteristics, although somewhat less impactful, still play a meaningful role. This model will be implemented within the POLARIS transportation systems simulator to improve the activity generation modeling workflow, and the prediction accuracy of various activity-travel components.

activity party composition↗

Composite quarks and leptons with embedded QCD

We construct a model of quark and lepton compositeness based on an 𝑆⁢𝑈⁡(15) gauge interaction that confines chiral preons, which are also charged under the weakly coupled 𝑆⁢𝑈⁢(4) PS ×𝑆⁢𝑈⁢(2) 𝐿 ×𝑆⁢𝑈⁢(2) 𝑅 gauge group. The breaking of the latter, down to the Standard Model group, is achieved by scalar 𝑆⁢𝑈⁡(15) bound states at a scale in the 30–100 TeV range. The embedding of the QCD gauge group in 𝑆⁢𝑈⁢(4) PS slows down the running of 𝛼 𝑠 in the UV. We estimate the effects of the strongly coupled 𝑆⁢𝑈⁡(15) dynamics on the running of the 𝑆⁢𝑈⁢(4) PS ×𝑆⁢𝑈⁢(2) 𝐿 ×𝑆⁢𝑈⁢(2) 𝑅 gauge couplings, which likely remain perturbative beyond the compositeness scale of about 10 3 –10 4 TeV, and even above a unification scale. A composite vectorlike lepton doublet acquires a mass in the TeV range probed at future colliders, and an extended Higgs sector arises from six-preon bound states.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Evaluation of Composite Structural Materials for Heliostat Cost Reduction

Structures manufactured from steel comprise up to 40% of a CSP heliostat's cost. Composite structures represent a potential opportunity to reduce this cost. A reference heliostat structural model has been created with a reflector area of 25m 2 . The design, constructed of low-carbon steel, pro-vides baseline deflection and stiffness under a 21 m/s operating wind speeds. Wind loads on the tracker structure are determined for both operating and stow conditions. An established roster of suitable metal alternative materials is considered including: glass, basalt, and carbon reinforced polymer (GFRP, BFRP, and CFRP respectively). Three heliostat components are investigated: the pylon, torque tube, and the purlin-strut assembly. Composite material properties are substituted for those of steel, and the beams are re-sized to match the original steel components' deflection under given wind loads. Weight and cost changes resulting from this resizing are evaluated. It is found that GFRP and BFRP represent a 3X–6X cost premium for the same operating deflection character-istics as steel across all three investigated component classes; with weight reduction only achieved for the purlin-strut assembly. While CFRP components can achieve approximately 25–75% weight savings depending on the application, this comes with a 9X–14X cost increase over the steel base-line for tube-type structures and roughly 5X cost increase when replacing c-channel structures. This work does not rule out the possibility of cost savings when the heliostat design and kinematics to take advantage of composites' specific properties.

14 SOLAR ENERGY↗

Rapid quantification of whole seed fatty acid amount, composition, and shape phenotypes from diverse oilseed species with large differences in seed size

Seed oils are widely used in the food, biofuel, and industrial feedstock industries, with their utility and value determined by total oil content and fatty acid composition. Current high throughput seed oil analysis methods either lack accuracy in total fatty acid profiling or require extensive labor for lipid extraction prior to derivatization to fatty acid methyl esters (FAME) and quantification by gas chromatography (GC). Alternatively, direct whole seed FAME production methods have been developed for the very small seeds in the model species Arabidopsis thaliana but these have generally not been adapted to larger seeds of most oilseed crops. High-throughput direct whole seed FAME production methods were optimized for seeds up to 5 mg each utilizing acid-catalyzed esterification. For the oilseed species Camelina sativa, Thlaspi avernse (pennycress), Cuphea viscosissima, and Brassica napus (var. Canola), the total seed fatty acid content and composition from direct seed esterification to FAME matched that of lipid extract derivatization demonstrating the accuracy of the methods. In combination with seed phenotyping using GridFree, this approach enabled the development of a rapid pipeline for simultaneous seed weight, count, size/shape phenotyping, and oil analysis. For the larger and tougher seeds produced by Limnanthes alba (Meadowfoam) and Cannabis sativa L. (hemp) the whole seed acid-based method proved insufficient, and prior laborious homogenization of seeds was required. Therefore, a rapid one-tube bead homogenization and base catalyzed-esterification method was developed. Base-derived fatty acid esterification cannot derivatize free fatty acids leading to slightly lower total seed fatty acid than acid-catalyzed methods, however the seed oil content and fatty acid composition that is valuable for screening large numbers of samples in research populations was accurately measured. New rapid whole seed fatty acid esterification and phenotyping protocols were developed to accurately assess oilseed lipid content. These methods are particularly valuable in oilseed research, breeding, and engineering applications where efficient analysis of large numbers of samples and accurate oil fatty acid profiling is essential. While having been developed for current and emerging oilseed crops, these methods also provide a foundation from which protocols might be established for new and emerging crop species.

59 BASIC BIOLOGICAL SCIENCES↗