Search NASA⌕ Search

SEARCH · Search NASA

Results for “concept normalization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Capture of liquid hydrogen boiloff with metal hydride absorbers

A procedure which uses metal hydrides to capture some of this low pressure (,1 psig) hydrogen for subsequent reliquefaction is described. Of the five normally occurring sources of boil-off vapor the stream associated with the off-loading of liquid tankers during dewar refill was identified as the most cost effective and readily recoverable. The design, fabrication and testing of a proof-of-concept capture device, operating at a rate that is commensurate with the evolution of vapor by the target stream, is described. Liberation of the captured hydrogen gas at pressure .15 psig at normal temperatures (typical liquefier compressor suction pressure) are also demonstrated. A payback time of less than three years is projected.

Rosso, M. J.↗

Use of a Prototype Airborne Separation Assurance System for Resolving Near-Term Conflicts During Autonomous Aircraft Operations

NASA is currently investigating a new concept of operations for the National Airspace System, designed to improve capacity while maintaining or improving current levels of safety. This concept, known as Distributed Air/Ground Traffic Management (DAGTM), allows appropriately equipped autonomous aircraft to maneuver freely for flight optimization while resolving conflicts with other traffic and staying out of special use airspace and hazardous weather. In order to perform these tasks, pilots use prototype conflict detection, prevention, and resolution tools, collectively known as an Airborne Separation Assurance System (ASAS). While ASAS would normally allow pilots to resolve conflicts before they become hazardous, evaluation of system performance in sudden, near-term conflicts is needed in order to determine concept feasibility. An experiment was conducted in NASA Langley's Air Traffic Operations Lab to evaluate the prototype ASAS for enabling pilots to resolve near-term conflicts and examine possible operational effects associated with the use of lower separation minimums. Sixteen commercial airline pilots flew a total of 32 traffic scenarios that required them to use prototype ASAS tools to resolve close range pop-up conflicts. Required separation standards were set at either 3 or 5 NM lateral spacing, with 1000 ft vertical separation being used for both cases. Reducing the lateral separation from 5 to 3 NM did not appear to increase operational risk, as indicated by the proximity to the intruder aircraft. Pilots performed better when they followed tactical guidance cues provided by ASAS than when they didn't follow the guidance. In an effort to improve compliance rate, ASAS design changes are currently under consideration. Further studies will of evaluate these design changes and consider integration issues between ASAS and existing Airborne Collision Avoidance Systems (ACAS).

Barhydt, Richard↗

Fail-safe system for activity cooled supersonic and hypersonic aircraft

A fail-safe-system concept was studied as an alternative to a redundant active cooling system for supersonic and hypersonic aircraft which use the heat sink of liquid-hydrogen fuel for cooling the aircraft structure. This concept consists of an abort maneuver by the aircraft and a passive thermal protection system (TPS) for the aircraft skin. The abort manuever provides a low-heat-load descent from normal cruise speed to a lower speed at which cooling is unnecessary, and the passive TPS allows the aircraft skin to absorb the abort heat load without exceeding critical skin temperature. On the basis of results obtained, it appears that this fail-safe-system concept warrants further consideration, inasmuch as a fail-safe system could possibly replace a redundant active cooling system with no increase in weight and would offer other potential advantages.

Jones, R. A.↗

An Efficient Analysis Methodology for Fluted-Core Composite Structures

The primary loading condition in launch-vehicle barrel sections is axial compression, and it is therefore important to understand the compression behavior of any structures, structural concepts, and materials considered in launch-vehicle designs. This understanding will necessarily come from a combination of test and analysis. However, certain potentially beneficial structures and structural concepts do not lend themselves to commonly used simplified analysis methods, and therefore innovative analysis methodologies must be developed if these structures and structural concepts are to be considered. This paper discusses such an analysis technique for the fluted-core sandwich composite structural concept. The presented technique is based on commercially available finite-element codes, and uses shell elements to capture behavior that would normally require solid elements to capture the detailed mechanical response of the structure. The shell thicknesses and offsets using this analysis technique are parameterized, and the parameters are adjusted through a heuristic procedure until this model matches the mechanical behavior of a more detailed shell-and-solid model. Additionally, the detailed shell-and-solid model can be strategically placed in a larger, global shell-only model to capture important local behavior. Comparisons between shell-only models, experiments, and more detailed shell-and-solid models show excellent agreement. The discussed analysis methodology, though only discussed in the context of fluted-core composites, is widely applicable to other concepts.

Oremont, Leonard↗

Concept of Operations for Commercial and Business Aircraft Synthetic Vision Systems

A concept of operations (CONOPS) for the Commercial and Business (CaB) aircraft synthetic vision systems (SVS) is described. The CaB SVS is expected to provide increased safety and operational benefits in normal and low visibility conditions. Providing operational benefits will promote SVS implementation in the Net, improve aviation safety, and assist in meeting the national aviation safety goal. SVS will enhance safety and enable consistent gate-to-gate aircraft operations in normal and low visibility conditions. The goal for developing SVS is to support operational minima as low as Category 3b in a variety of environments. For departure and ground operations, the SVS goal is to enable operations with a runway visual range of 300 feet. The system is an integrated display concept that provides a virtual visual environment. The SVS virtual visual environment is composed of three components: an enhanced intuitive view of the flight environment, hazard and obstacle defection and display, and precision navigation guidance. The virtual visual environment will support enhanced operations procedures during all phases of flight - ground operations, departure, en route, and arrival. The applications selected for emphasis in this document include low visibility departures and arrivals including parallel runway operations, and low visibility airport surface operations. These particular applications were selected because of significant potential benefits afforded by SVS.

Williams Daniel M.↗

High-power microwave power divider concept

Variable power divider keeps microwave transmitter at full power. This preserves the bandwidth and modulation characteristics and proportions any amount of the full power from the normal antenna into a dissipative load.

Kolbly, R. B.↗

Atomic oxygen transport in the thermosphere.

The photodissociation of oxygen in the lower thermosphere is evaluated to obtain its global average value and the hemispheric imbalance. The observed concentrations of atomic oxygen do not reflect this imbalance in production due to the effect of seasonal wind patterns redistributing the atomic oxygen. The wind system necessary to compensate for the imbalance in solar thermal input into the lower thermosphere is found to transport an amount of atomic oxygen sufficient to compensate for the hemispheric imbalance in production. Ionospheric data indicate a winter enhancement in atomic oxygen concentration; to produce this, a higher degree of oxygen dissociation than that normally accepted (i.e., higher than an atomic to molecular oxygen ratio of unity at 120 km) is needed. The concept that the concentrations of atomic oxygen observed over the winter polar region are maintained by transport from lower latitudes requires that eddy diffusion coefficients derived from vertical transport at low latitudes (ignoring horizontal transport) be reduced by about 25%.

Johnson, F. S.↗

A dual frequency radar for ocean roughness sampling

A microwave technique for determining the roughness (rms wave height) of a randomly varying air-water interface has been developed theoretically, verified with laboratory wavetank studies and is currently being implemented for ocean surface measurements in a series of applications flight experiments. These aircraft observations will be near the Chesapeake Light Tower and will include a range of altitudes and sea conditions. The measurement concept involves cross-correlating the envelope fluctuations on two received carriers that are monochromatic when transmitted in a normal direction to the interface and are observed in a backscatter direction after reflection by the large number of randomly distributed specular points on the surface. The measured correlation coefficient (normalized covariance) as a function of carrier frequency separation will depend on the surface roughness, specifically the probability density function of the specular point height. Details of the flight system are discussed, and preliminary flight results are presented.

Weissman, D. E.↗

Further developments in simple total energy sensors

A simple total energy probe concept using principles of laminar flow around a cylinder and pressure distribution is reviewed and flow fields around cylinders normal to and inclined to the flow are described. A variety of bent-up probe configurations were tested to explore variations in geometry. Test results are presented on the effects of sensor length, hole location, and angle of sweep. Comparisons are made with other probe tests reported in the literature. Damping restrictors and their use in filtering gusts are summarized. Flow field effects, indicating the variables involved for different mounting locations on aircraft, are discussed.

Nicks, O. W.↗

Computation of incompressible, three-dimensional turbulent boundary layers and comparison with experiment

Incompressible three dimensional, turbulent boundary layer (3DTBL) experiments were simulated numerically by integrating the boundary layer equations together with an algebraic eddy viscosity turbulence model. For the flow treated, the downstream portion, where the crossflow was large, was not predicted with the present computational method; the flow was significantly influenced by elliptic flow field effects. Departures from the boundary layer concept are indicated. Calculations agreed reasonably well with the mean flow development up to separation. In one experiment the normal pressure gradients were found to be neligible in regions with large skewing and allowed testing turbulence models using the boundary layer equations. The simulation of this flow compared favorably with the experimental data throughout the flow field and suggested the applicability of algebraic eddy viscosity models for 3DTBLs.

Mueller, U. R.↗

A.I.-based real-time support for high performance aircraft operations

Artificial intelligence (AI) based software and hardware concepts are applied to the handling system malfunctions during flight tests. A representation of malfunction procedure logic using Boolean normal forms are presented. The representation facilitates the automation of malfunction procedures and provides easy testing for the embedded rules. It also forms a potential basis for a parallel implementation in logic hardware. The extraction of logic control rules, from dynamic simulation and their adaptive revision after partial failure are examined. It uses a simplified 2-dimensional aircraft model with a controller that adaptively extracts control rules for directional thrust that satisfies a navigational goal without exceeding pre-established position and velocity limits. Failure recovery (rule adjusting) is examined after partial actuator failure. While this experiment was performed with primitive aircraft and mission models, it illustrates an important paradigm and provided complexity extrapolations for the proposed extraction of expertise from simulation, as discussed. The use of relaxation and inexact reasoning in expert systems was also investigated.

Vidal, J. J.↗

Transformative Technology for FLASH Radiation Therapy: A Snowmass 2021 White Paper

Conventional cancer therapies include surgery, radiation therapy, chemotherapy, and, more recently, immunotherapy. These modalities are often combined to improve the therapeutic index. The general concept of radiation therapy is to increase the therapeutic index by creating a physical dose differential between tumors and normal tissues through precision dose targeting, image guidance, and high radiation beams that deliver radiation dose with high conformality, e.g., protons and ions. However, treatment and cure are still limited by normal tissue radiation toxicity, with many patients experiencing acute and long-term side effects. Recently, however, a fundamentally different paradigm for increasing the therapeutic index of radiation therapy has emerged, supported by preclinical research, and based on the FLASH radiation effect. FLASH radiation therapy (FLASH-RT) is an ultra-high dose-rate delivery of a therapeutic radiation dose within a fraction of a second. Experimental studies have shown that normal tissues seem to be universally spared at these high dose rates, whereas tumors are not. The dose delivery conditions are not yet fully characterized. Still, it is currently estimated that large doses of 10 Gy or more delivered in 200 ms or less produce normal tissue sparing effects yet effectively kill tumor cells. There is a great opportunity, but also many technical challenges, for the accelerator community to create the required dose rates with novel and compact accelerators to ensure the safe delivery of FLASH radiation beams.

43 PARTICLE ACCELERATORS↗

A Physics-Based DNI Model for Advancing Solar Resource Assessment and Forecasting: Preprint

Direct Normal Irradiance (DNI) is one of the most used quantities to quantify the magnitude of solar energy resource. The concept of DNI is often interpreted differently for ground measurements and solar forecasting by numerical weather prediction (NWP) models, leading to substantial bias during evaluation of DNI forecasts especially under cloudy-sky conditions. To eliminate the bias, we use the Fast All-sky Radiation Model for Solar applications with DNI (FARMS-DNI) to provide a physics-based solution of solar radiation in the circumsolar region. The FARMS-DNI is implemented in the Weather Research and Forecasting model with solar extensions (WRF-Solar) to forecast day-ahead DNI in the north America. By comparing with conventional predictions from WRF-Solar and satellite observations from the National Solar Radiation Data Base (NSRDB), we found significant improvements in our prediction of DNI.

DNI↗

Multi-access laser communications terminal

The Optical Multi-Access (OMA) Terminal is capable of establishing up to six simultaneous high-data-rate communication links between low-Earth-orbit satellites and a host satellite at synchronous orbit with only one 16-inch-diameter antenna on the synchronous satellite. The advantage over equivalent RF systems in space weight, power, and swept volume is great when applied to NASA satellite communications networks. A photograph of the 3-channel prototype constructed under the present contract to demonstrate the feasibility of the concept is presented. The telescope has a 10-inch clear aperture and a 22 deg full field of view. It consists of 4 refractive elements to achieve a telecentric focus, i.e., the focused beam is normal to the focal plane at all field angles. This feature permits image pick-up optics in the focal plane to track satellite images without tilting their optic axes to accommodate field angle. The geometry of the imager-pick-up concept and the coordinate system of the swinging arm and disk mechanism for image pick-up are shown. Optics in the arm relay the telescope focus to a communications and tracking receiver and introduce the transmitted beacon beam on a path collinear with the receive path. The electronic circuits for the communications and tracking receivers are contained on the arm and disk assemblies and relay signals to an associated PC-based operator's console for control of the arm and disk motor drive through a flexible cable which permits +/- 240 deg travel for each arm and disk assembly. Power supplies and laser transmitters are mounted in the cradle for the telescope. A single-mode fiber in the cable is used to carry the laser transmitter signal to the arm optics. The promise of the optical multi-access terminal towards which the prototype effort worked is shown. The emphasis in the prototype development was the demonstration of the unique aspect of the concept, and where possible, cost avoidance compromises were implemented in areas already proven on other programs. The design details are described in section 2, the prototype test results in section 3, additional development required in section 4, and conclusions in section 5.

Source record↗

Urine Pretreat Injection System

A new method of introducing the OXONE (Registered Trademark) Monopersulfate Compound for urine pretreat into a two-phase urine/air flow stream has been successfully tested and evaluated. The feasibility of this innovative method has been established for purposes of providing a simple, convenient, and safe method of handling a chemical pretreat required for urine processing in a microgravity space environment. Also, the Oxone portion of the urine pretreat has demonstrated the following advantages during real time collection of 750 pounds of urine in a Space Station design two-phase urine Fan/Separator: Eliminated urine precipitate buildup on internal hardware and plumbing; Minimized odor from collected urine; and Virtually eliminated airborne bacteria. The urine pretreat, as presently defined for the Space Station program for proper downstream processing of urine, is a two-part chemical treatment of 5.0 grams of Oxone and 2.3 ml of H2SO4 per liter of urine. This study program and test demonstrated only the addition of the proper ratio of Oxone into the urine collection system upstream of the Fan/Separator. This program was divided into the following three major tasks: (1) A trade study, to define and recommend the type of Oxone injection method to pursue further; (2) The design and fabrication of the selected method; and (3) A test program using high fidelity hardware and fresh urine to demonstrate the method feasibility. The trade study was conducted which included defining several methods for injecting Oxone in different forms into a urine system. Oxone was considered in a liquid, solid, paste and powered form. The trade study and the resulting recommendation were presented at a trade study review held at Hamilton Standard on 24-25 October 94. An agreement was reached at the meeting to continue the solid tablet in a bag concept which included a series of tablets suspended in the urine/air flow stream. These Oxone tablets would slowly dissolve at a controlled rate providing the proper concentration in the collected urine. To implement the solid tablet in a bag approach, a design concept was completed with prototype drawings of the complete urine pretreat prefilter assembly. A successful fabrication technique was developed for retaining the Oxone tablets in a fabric casing attached to the end of the existing Space Station Waste Collection System urine prefilter assembly. The final pretreat prefilter configuration held sufficient Oxone in a tablet form to allow normal scheduled daily (or twice daily) change out of the urine filter depending on the use rate of the Space Station urine collection system. The actual tests to prove the concept were conducted using the Urine Fan/Separator assembly that was originally used in the STS-52 Design Test Objective (DTO) urinal assembly. Other related tests were conducted to demonstrate the actual minimum ratio of Oxone to urine that will control microbial growth.

Source record↗

Superconductivity and Local Inversion-Symmetry Breaking

Inversion and time reversal are essential symmetries for the structure of Cooper pairs in superconductors. The loss of one or both leads to modifications to this structure and can change the properties of the superconducting phases in profound ways. Superconductivity in materials lacking inversion symmetry, or noncentrosymmetric materials, has become an important topic. These materials show unusual magnetic and magnetoelectric properties and can host topological superconductivity. Recently, crystal structures with local, but not global, inversion-symmetry breaking have attracted attention. Here, superconductivity can exhibit phenomena not naively expected in centrosymmetric materials. In this review, we first introduce the concept of locally noncentrosymmetric crystals and different material realizations. We then discuss consequences of such local symmetry breaking on the normal state electronic structure and the classification of superconducting order parameters. Finally, we review the expected and, in parts, already observed phenomenology of unconventional superconductivity and possible topological superconducting phases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Calculations of the limb radiance of Venus in the 600 to 700 per cm region and their application to spacecraft navigation.

Limb radiance profiles for Venus in the 600 to 700 per cm spectral band are derived for two sets of model atmospheres. The radiance computations make use of a strong line transmission model. Both an extreme variability atmospheric model set and a normal variability set are derived and discussed, as are the effects of clouds and surface pressure uncertainties. A horizon locator concept based on the derived radiance profiles is presented, through its implementation in a conceptual systems design. The locator concept developed shows promise of locating the Venus limb to better than 2 km accuracy at the horizon, or 0.05 deg for a 500-km orbit.

Ohring, G.↗

Skylab EVA system development

EVA hardware design is traced from initial conceptual development to final flight configuration. Major concepts considered during design evolution are identified, and reasons for the acceptance or rejection of these concepts are discussed. An iterative approach to simulations and testing was found useful. Early conceptual efforts concentrated on analyses and normal gravity, low-cost, low-fidelity mockups; later design phases combined normal gravity and neutral buoyancy simulations of increasing fidelity. Restudying after each change consistently drove EVA hardware toward operational and mechanical simplicity.-

Heckman, R. T.↗