Search NASA⌕ Search

SEARCH · Search NASA

Results for “contact time”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Solar power satellite system definition study. Part 1 and part 2, volume 1: Executive summary

The Solar Power Satellite principle is illustrated and it shows that in a geostationary orbit 36,000 km above the earth's equator, each SPS is in sunlight 99% of the time and in continuous line of sight contact with its ground receiving station. Electrical power produced on the satellite by photovoltaic or heat engine conversion of sunlight is then converted to radio frequency energy at high efficiency, and formed into a focused beam precisely aimed at the SP ground stations. The ground station receiving antenna reconverts the energy into electricity for distribution.

Source record↗
NASA NTRS1978

Status of wraparound contact solar cells and arrays

Solar cells with wraparound contacts provide the following advantages in array assembly: (1) eliminate the need for discretely formed, damage susceptible series tabs; (2) eliminate the n gap problem by allowing the use of uniform covers over the entire cell surface; (3) allow a higher packing factor by reducing the additional series spacing formly required for forming, and routing the series tab; and (4) allow the cell bonding to the interconnect system to be a single-side function wherein series contacts can be made at the same time parallel contracts are made.

Baraona, C. R.↗
NASA NTRS1977

A comparison between Nimbus 5 THIR and ITPR temperatures and derived winds with rawinsonde data obtained in the AVE II experiment

During the second Atmospheric Variability Experiment (AVE II), atmospheric temperature profiles were computed from Nimbus 5 data, which comprised ITPR, NEMS, and SCR measurements. Rawinsonde data were obtained from NWS stations in the AVE II network and processed for each pressure contact; the soundings closest in space and time were interpolated to the Nimbus 5 sounding points for comparison purposes. Cross sections of thermal and geostrophic winds were computed from satellite-derived cross sections of temperature along the Nimbus orbital track.

Arnold, J. E.↗
NASA NTRS1983

Failure mechanics in low-velocity impacts on thin composite plates

Eight-ply quasi-isotropic composite plates of Thornel 300 graphite in Narmco 5208 epoxy resin (T300/5208) were tested to establish the degree of equivalence between low-velocity impact and static testing. Both the deformation and failure mechanics under impact were representable by static indentation tests. Under low-velocity impacts such as tool drops, the dominant deformation mode of the plates was the first, or static, mode. Higher modes are excited on contact, but they decay significantly by the time the first-mode load reaches a maximum. The delamination patterns were observed by X-ray analysis. The areas of maximum delamination patterns were observed by X-ray analysis. The areas of maximum delamination coincided with the areas of highest peel stresses. The extent of delamination was similar for static and impact tests. Fiber failure damage was established by tensile tests on small fiber bundles obtained by deplying test specimens. The onset of fiber damage was in internal plies near the lower surface of the plates. The distribution and amount of fiber damage was similar fo impact and static tests.

Elber, W.↗
NASA NTRS1984

Impacting device for testing insulation

An electro-mechanical impacting device for testing the bonding of foam insulation to metal is descirbed. The device lightly impacts foam insulation attached to metal to determine whether the insulation is properly bonded to the metal and to determine the quality of the bond. A force measuring device, preferably a load cell mounted on the impacting device, measures the force of the impact and the duration of the time the hammer head is actually in contact with the insulation. The impactor is designed in the form of a handgun having a driving spring which can propel a plunger forward to cause a hammer head to impact the insulation. The device utilizes a trigger mechanism which provides precise adjustements, allowing fireproof operation.

Redmon, J. W.↗
NASA NTRS1988

Evaluating Solid-Lubricant Films

Report describes experimental techniques for measuring properties of solid-lubricant films. Discusses experimental parameters. Reviews basic pin-on-disk configurations and methods of preparing disks and applying solid lubricants. Techniques for constant-temperature testing, low-contact-stress testing, and temperature-versus-time testing presented. Suggests methods of measuring pin-wear volume and recommends ways of presenting data.

Fusaro, Robert L.↗
NASA NTRS1989

Transient-mode liquid phase epitaxial growth of GaAs on GaAs-coated Si substrates prepared by migration-enhanced molecular beam epitaxy

Planar oxide-maskless growth of GaAs was demonstrated by transient-mode liquid phase epitaxy (TMLPE) on GaAs-coated Si substrates that were prepared by migration-enhanced molecular beam epitaxy (MEMBE). In TMLPE, the cool substrate was brought into contact with hot melts for a short time. A GaAs layer as thick as 30 microns was grown in 10 sec. The etch pits observed in TMLPE-grown layers became longer in one direction and decreased in density with increasing the TMLPE epilayer thickness. The density of etch pits in a 20 micron-thick layer was approximately 5 x 10 the 6th/sq cm. Strong bandgap emission elliptically polarized with a major axis perpendicular to the surface was observed at about 910 nm, while deep-level emission from the TMLPE/MEMBE GaAs interface was detected at 980 nm. The photoluminescence intensity divided by the carrier concentration of the TMLPE-grown layer was about 270 times larger than that of the MEMBE-grown layer used as a substrate.

Nakamura, Shuji↗
NASA NTRS1989

Space Station Freedom Workshop Opportunities for Commercial Users and Providers: Issues and Recommendations

The responses to issues and questions raised at the Space Station Freedom Workshops are compiled. The findings are presented under broad divisions of general, materials processing in space, commercial earth and ocean observations, life sciences, infrastructure services, and infrastructure policy. The responses represent the best answers available at this time and future modifications may be expected. Contact names, telephone numbers, and organizations are included.

Source record↗
NASA NTRS1992

How to get on board Space Station Freedom

Space Station Freedom will accommodate researchers with interests in science, technology and commercial applications. NASA sponsors will be responsible for selecting the U.S. researchers for Space Station Freedom. The four NASA sponsors are: Office of Space Science and Applications (OSSA), Office of Aeronautics and Space Technology (OAST), Office of Commercial Programs (OCP), and the Office of Space Flight (OSF). The areas of research responsibility for each sponsor are presented. The researcher solicitation vehicles used by OSSA and OAST and the methodology for researchers seeking sponsorship from OCP and OSF as well as the pricing policy are discussed. Descriptions of flight planning, payload integration and operations functions are presented. Three categories of payloads and their respective payload integration times are discussed. Researchers are advised to contact a NASA sponsor and a source which lists the points of contact for the NASA sponsors is noted.

Bartoe, John-David↗
NASA NTRS2000

Dynamic Response of a Planetary Gear System Using a Finite Element/Contact Mechanics Model

The dynamic response of a helicopter planetary gear system is examined over a wide range of operating speeds and torques. The analysis tool is a unique, semianalytical finite element formulation that admits precise representation of the tooth geometry and contact forces that are crucial in gear dynamics. Importantly, no a priori specification of static transmission error excitation or mesh frequency variation is required; the dynamic contact forces are evaluated internally at each time step. The calculated response shows classical resonances when a harmonic of mesh frequency coincides with a natural frequency. However, peculiar behavior occurs where resonances expected to be excited at a given speed are absent. This absence of particular modes is explained by analytical relationships that depend on the planetary configuration and mesh frequency harmonic. The torque sensitivity of the dynamic response is examined and compared to static analyses. Rotation mode response is shown to be more sensitive to input torque than translational mode response.

Parker, Robert G.↗
NASA NTRS1999

Single Particle Transport Through Carbon Nanotube Wires: Effect of Defects and Polyhedral Cap

The ability to manipulate carbon nanotubes with increasing precision has enabled a large number of successful electron transport experiments. These studies have primarily focussed on characterizing transport through both metallic and semiconducting wires. Tans et al. demonstrated ballistic transport in single-wall nanotubes for the first time, although the experimental configuration incurred large contact resistance. Subsequently, methods of producing low contact resistances have been developed and two terminal conductances smaller than 50 k-ohms have been repeatably demonstrated in single-wall and multi-wall nanotubes. In multi-wall nanotubes, Frank et al. demonstrated a resistance of approximately h/2e(exp 2) in a configuration where the outermost layer made contact to a liquid metal. This was followed by the work of de Pablo et al. where a resistance of h(bar)/27e(exp 2) (approximately 478 ohms) was measured in a configuration where electrical contact was made to many layers of a multi-wall nanotube. Frank et al. and Pablo et al. note that each conducting layer contributes a conductance of only 2e(exp 2)/h, instead of the 4e(exp 2)/h that a single particle mode counting picture yields. These small resistances have been obtained in microns long nanotubes, making them the best conducting molecular wires to date. The large conductance of nanotube wires stems from the fact that the crossing bands of nanotubes are robust to defect scattering.

Anantram, M. P.↗
NASA NTRS1998

Effectiveness of an Expert System for Astronaut Assistance on a Sleep Experiment

Principal Investigator-in-a-Box ([PI]) is an expert system designed to train and assist astronauts with the performance of an experiment outside their field of expertise, particularly when contact with the Principal Investigators on the ground is limited or impossible. In the current case, [PI] was designed to assist with the calibration and troubleshooting procedures of the Neurolab Sleep and Respiration Experiment during the pre-sleep period of no ground contact. It displays physiological signals in real time during the pre-sleep instrumentation period, and alerts the astronauts when a poor signal quality is detected. Results of the first study indicated a beneficial effect of [PI] and training in reducing anomaly detection time and the number of undetected anomalies. For the in-flight performance, excluding the saturated signals, the expert system had an 84.2% detection accuracy, and the questionnaires filled out by the astronauts showed positive crew reactions to the expert system.

Heher, Dennis↗
NASA NTRS2011

Crop and Substrate Tests with Single Use Rooting "Pillows" for the VEGGIE Plant Growth Hardware

VEGGIE is a small plant production chamber built by ORBITEC. This chamber can be collapsed for easy stowage and deployed in orbit. It is designed for gravity independent operation, and provides 0.17 square m of crop growth area with three primary subsystems: an LED light panel, extendable transparent Teflon bellows to enclose the plants, and a wicking reservoir. VEGGIE would provide the capability for astronauts to grow fresh foods for dietary supplementation. Initial planting concepts tested with the VEGGIE included direct seeding or plug placement on the reservoir surface. These options had issues of salt accumulation and eventual toxicity if the reservoir was filled with nutrient solution, and hardware reuse was limited due to sanitation. In response a rooting packet or "pillow" concept was developed: single-use bags of media containing time release fertilizer with a wicking surface contacting the VEGGIE reservoir. Pillows being tested are small electrostatic bags with a Nitex nylon mesh side, each holding 100 mL of dry media. Six pillows fit in one VEGGIE unit; however pillow size could vary depending on crop selected. Seeds can be planted directly in pillows and planted pillows can be hydrated in space as desired. Our goals were to define optimal media and crops for an ISS mission scenario. Plant tests in pillows were performed in a controlled environment chamber set to habitat-relevant conditions, and capillary reservoir analogs were utilized. Media tested within pillows included: a commercial peat-based potting mix, arcillite (calcined clay), perlite: vermiculite, and peat-based: arcillite blends. Testing included 15 types of leafy greens, snow pea, radish, and herbs. Media performance was crop dependent, but generally plants showed the greatest growth in the peat-based: arcillite mixes. Crops with the best performance in pillows were identified, and testing is underway with select leafy greens examining plant and microbial load response to repeated harvest. We plan to use findings from previous flight testing with media to evaluate the effects of capillary flow from the reservoir to pillows in microgravity.

Massa, Gioia↗
NASA NTRS2018

Autonomous Nested Search for Hydrothermal Venting

Ocean Worlds in the outer solar system represent one of the best chances for the discovery of extra-terrestrial life. Bodies, such as Europa and Enceladus, are thought to harbor liquid oceans, often encased in a thick icy shell. In order to further investigate these oceans, a new mission concept needs to be developed, a submersible craft. This vehicle would be required to traverse the icy shell and travel hundreds or even thousands of kilometers to survey the ocean below. In doing this, the vehicle might be out of contact for weeks or months at a time. The vehicle must be able to autonomously detect,locate, and study features of interest. One potential target is hydrothermal venting, due to their unique ecosystems on Earth. We have developed an autonomous, nested search strategy to locate sources of hydrothermal venting based on currently used methods. To test this search technique a simulation environment was developed using a hydrothermal plume dispersion simulation and a vehicle model. We show the effectiveness of the search method in this environment.

Seewald, Jeffrey S.↗
NASA NTRS2018

Evaluation of Opportunistic Contact Graph Routing in Random Mobility Environments

Routing in networks where nodes move randomly is particularly challenging due their potentially unpredictable, and rapidly changing topology. Several routing algorithms have been presented in the literature to address the needs of such networks, most of them implementing variants of controlled network flooding in the hope of successful data delivery. In this note, we compare the results of previous routing algorithms with Opportunistic Contact Graph Routing (OCGR), an enhanced version of Contact Graph Routing (CGR) that is suitable for networks where contacts cannot always be scheduled ahead of time. To perform the benchmark, we simulate a network of nodes moving in a certain space according to the Random Waypoint Mobility Model, and then take measurements of bundle delivery probabilty and overhead ratio as metrics of performance and cost respectively. Through this exercise, we demonstrate that the performance of OCGR is highly dependent on the type of network under consideration (e.g. very sparse vs. densely connected) and the assumed mobility model.

Burleigh, Scott↗
NASA NTRSDate not supplied

Material Compatibility Study of Coated Metals to Maintain Biocidal Silver in a Spacecraft Potable Water System

Ionic silver-based biocide is an option of strong interest for future exploration and has been baselined for several emerging spacecraft potable water systems. A challenge for the use of silver biocide remains the depletion of ionic silver on wetted materials of construction. Consequently, the design and/or selection of materials that can be used as the wetted system components need specific consideration. As part of the strategy to address this issue, a multitiered approach is being investigated that looks at combinations of conventional and non-conventional spacecraft treatment processes and materials. In this study, eleven chemically-resistant polymer coatings were applied as surface treatments onto coupons that were cut out from three types of conventional spacecraft-grade metals (Titanium Grade 2, Inconel 718, and 316L Stainless Steel). The coated metals were immersed in a static 400 parts per billion silver biocide solution at a surface-area-to-volume ratio of 2.0 cm^-1 and left to soak for predefined periods of time. The concentration of the solution in contact with the coated samples were then analyzed via inductively coupled plasma mass spectrometry, and the data used to determine the extent to which the coatings provided a barrier to silver loss. This paper summarizes the coating selection process, the configuration of the test, and the performance of each coating-metal combination as a mitigation to silver depletion. The preliminary results demonstrate that select coatings are proving effective at maintaining biocidal silver concentrations. The knowledge acquired through this investigation will be used to assess the feasibility of using these coatings as a robust strategy for maintaining biocidal silver in the water systems. Future studies are planned to assess the specific use of these coatings and to better understand the implications of utilizing this material approach in the future spacecraft potable water system designs.

coatings↗
NASA NTRSDate not supplied

Material Compatibility Study of Coated Metals to Maintain Biocidal Silver in a Spacecraft Potable Water System

Ionic silver-based biocide is an option of strong interest for future exploration and has been baselined for several emerging spacecraft potable water systems. A challenge for the use of silver biocide remains the depletion of ionic silver on wetted materials of construction. Consequently, the design and/or selection of materials that can be used as the wetted system components need specific consideration. As part of the strategy to address this issue, a multitiered approach is being investigated that looks at combinations of conventional and non-conventional spacecraft treatment processes and materials. In this study, eleven chemically-resistant polymer coatings were applied as surface treatments onto coupons that were cut out from three types of conventional spacecraft-grade metals (Titanium Grade 2, Inconel 718, and 316L Stainless Steel). The coated metals were immersed in a static 400 parts per billion silver biocide solution at a surface-area-to-volume ratio of 2.0 cm^-1 and left to soak for predefined periods of time. The concentration of the solution in contact with the coated samples were then analyzed via inductively coupled plasma mass spectrometry, and the data used to determine the extent to which the coatings provided a barrier to silver loss. This paper summarizes the coating selection process, the configuration of the test, and the performance of each coating-metal combination as a mitigation to silver depletion. The preliminary results demonstrate that select coatings are proving effective at maintaining biocidal silver concentrations. The knowledge acquired through this investigation will be used to assess the feasibility of using these coatings as a robust strategy for maintaining biocidal silver in the water systems. Future studies are planned to assess the specific use of these coatings and to better understand the implications of utilizing this material approach in the future spacecraft potable water system designs.

coatings↗
NASA NTRSDate not supplied

Celestial Navigation in Cislunar Space with autoNGC

Celestial navigation (CelNav) is a source of navigation observables where images of known solar system bodies are used to locate a spacecraft, beneficial within the solar system for both cislunar and deep space missions. CelNav provides a variety of design benefits to support and enable current and new autonomous space operations- using only a camera and a processor to produce in-situ measurements for navigation. This technology reduces subscription to ground-based tracking during all phases of a mission, freeing up resources for other operational needs. This also supports secure navigation since it eliminates the need for ground contact. CelNav enables missions where the light time delay between Earth and the spacecraft is too long (or the Earth to spacecraft line of sight is obscured) to support critical operations. It also enables smaller mission classes, where Deep Space Network (DSN)time is cost prohibitive, to reduce its cost by focusing primarily on data downlink. Finally, it enables the NASA Artemis program and other cislunar human space flight by providing redundant navigation to traditional radiometric tracking. In this presentation, we discuss the implementation of a CelNav app in autonomous Navigation, Guidance, and Control (autoNGC), a comprehensive flight software suite for onboard autonomy that is built on the core Flight System (cFS). The presentation also summarizes the results of flight software-in-the-loop (SIL) and processor-in-the-loop (PIL) demonstrations. Both are high-fidelity simulations with the use of a camera emulator hosted on a GPU server that simulates images that would be captured by the camera. The CelNav app leverages the use of cGIANT (cFS Goddard Image Analysis and Navigation Tool).Previously developed for the autoNGC software suite, cGIANT is an onboard autonomous image processing and optical navigation (OpNav) tool that performs limb-based OpNav and Terrain Relative Navigation. The added CelNav capability of cGIANT generates bearing measurements to multiple known celestial bodies (planets, moons, asteroids, comets, etc.) in monocular (2D) images. These observables are then fed to the Goddard Enhanced Onboard Navigation System (GEONS)navigation filter app, enabling us to navigate the spacecraft autonomously. In early 2025, the autoNGC CelNav capability is planned to be flight tested as part of the onboard autonomy experiment on the Cislunar Autonomous Positioning System Technology Operations and Navigation Experiment(CAPSTONE) spacecraft that is currently in a Lunar Near Rectilinear Halo Orbit(NRHO).

celestial navigation↗