An Artificial Protective Coating toward Dendrite-Free Lithium-Metal Anodes for Lithium–Sulfur Batteries
Not provided.
Energy & Fuels↗
SEARCH · Search NASA
Results for “dendritic cell”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Recombination-active defects in silicon ribbon and polycrystalline solar cells
This paper reports results from a study of recombination-active structural defects in silicon ribbon and polycrystalline solar cells using the electron beam induced current (EBIC) technique in a scanning electron microscope. It is demonstrated that low temperature EBIC measurements can reveal a range of defects that are not observable at room temperature, including slip dislocations in silicon dendritic web ribbons as well as decorated twin boundaries and dislocation complexes in cast polycrystalline silicon solar cell materials.
Cheng, L. J.↗
Phase-Transition Interlayer Enables High-Performance Solid-State Sodium Batteries with Sulfide Solid Electrolyte
All-solid-state sodium (Na) batteries (ASSSBs) using sulfide-based solid electrolytes (SEs) have attracted intensive attention due to their superior safety, high energy density and low cost. However, interfacial issue is one of the biggest challenges to achieve high-performance sulfide-based ASSSBs due to the serious reactions between active Na metal and sulfide SEs at the interface. To address the interfacial challenges, we propose in this paper a simple and efficient approach by introducing a polymer electrolyte as an interlayer to stabilize the interface. Na 3 SbS 4 as a model sulfide SE is used to demonstrate the interlayer strategy to stabilize the interface by preventing the detrimental reactions and inhibiting Na dendrites. As a result, stable Na plating/stripping was observed in Na symmetric cells under the current density of 0.1 mA cm –2 . Moreover, ASSSBs with Na metal and TiS 2 electrode delivered long-term stability over 300 cycles remaining a specific capacity above 100 mAh g –1 , and FeS 2 ||Na cells exhibited an impressive specific capacity of up to 200 mAh g –1 after the 20th cycles. This work demonstrates an efficient strategy to address interfacial challenges between sulfide SEs and Na metal, which contributes to the development of ASSSBs in next-generation energy storage systems.
25 ENERGY STORAGE↗
Scalable, Ultrathin, and High-Temperature-Resistant Solid Polymer Electrolytes for Energy-Dense Lithium Metal Batteries
We report all-solid-state batteries (ASSBs) demonstrate great promise, offering high energy density, good thermal stability, and safe operation compared with traditional Li-ion batteries. Among various solid-state electrolytes (SSEs), solid polymer electrolytes (SPEs) offer an attractive choice due to their thinness, low density, and good manufacturability. However, ultrathin SPEs that work with practical current densities or at high temperatures remain challenging, limiting applicable conditions of SPE-based batteries. Here, the authors report a novel scalable, ultrathin, and high-temperature-resistant SPE for ASSBs. This design includes an electrospun polyacrylonitrile (PAN) matrix and polyethylene oxide (PEO)/Li salt ionic conductor, which offers a stable LiF and Li 3 N containing SSE/Li interface. The unique interface—as well as the good mechanical strength—inhibits lithium dendrites and prevents short circuiting. As a result, symmetrical Li-Li cells deliver more than 300 h cyclability at 0.5 mA cm -2 . ASSBs fabricated with only 5 µm-thickness PAN-PEO/lithium bis(trifluoromethanesulfonyl)imide reach 300 cycles at 0.3 C rate at 60 °C. The excellent thermal stability of PAN also results in safer SPEs at high temperatures. The design extends battery operation up to temperatures of 120 and 150 °C, where it achieves 500 cycles at C/2 rate and 100 cycles at 2C rate, respectively.
25 ENERGY STORAGE↗
Composite Lithium Metal Structure to Mitigate Pulverization and Enable Long‐Life Batteries
In lithium metal batteries, non‐uniform stripping of lithium results in pit formation, which promotes subsequent non‐uniform, dendritic deposition. This viscous cycle leads to pulverization of lithium which promotes cell shorting or capacity degradation, symptoms further exaggerated by high electrode areal loading and lean electrolytes. Here, to address this challenge, a composite lithium metal anode is engineered that contains uniformly distributed, nanometer‐sized carbon particles. This composite lithium is shown to strip more uniformly since the growth of non‐uniform pits is intercepted by the carbon particles. This mechanism is corroborated by a continuum electrochemical model. Subsequent lithium deposition on carbon particles is also found to be more uniform than on the surface with irregular pits. Notably, the pulverization rate of composite lithium is 26 times slower than that of commercial lithium. Moreover, in a Li‐S battery with sulfurized polyacrylonitrile cathode, the use of the composite anode extends the cycle life by three times when the areal capacity is 8 mAh cm −2 . The approach of using an engineered lithium composite structure to address challenges during both stripping and plating can inform future designs of lithium metal anodes for high areal capacity operations.
high areal capacity↗
Carbon nanotube (CNT) reinforced 316L stainless steel composites made by laser powder bed fusion: Microstructure and wear response
Carbon nanotube (CNT) reinforced 316L stainless steel (SS) composites were fabricated by laser powder bed fusion (LPBF) additive manufacturing (AM). This study focuses on microstructure evolution, hardness, and wear behavior. The wear behavior for AM 316L SS and 1 wt% CNT/316L SS was studied by a dry sliding test under normal loads of 10, 15, and 25 N. The addition of CNT to 316L SS led to the change of solidification mode from cellular/columnar to dendritic growth, producing grain refinement. Nanoscale dendrites were observed. Although TEM characterization confirmed the existence of CNT in cell interior, most CNT were damaged, resulting in carbon material segregation along cellular/dendritic boundaries. The wear rate was found dramatically decreased due to the improved hardness. Compared to the adhesive and abrasive wear in AM 316L SS, the wear mechanism of CNT/316L composite was adhesion and oxidative wear. Furthermore, enhanced cellular/dendritic boundary strengthening by carbon segregation was the main strengthening mechanism of CNT/316L composite.
36 MATERIALS SCIENCE↗
A High-Ceramic-Loading LATP–PVDF–Al 2 O 3 Composite Film for Lithium-Ion Batteries With Favorable Porous Microstructure and Enhanced Thermal Stability
A separator plays a crucial role in a Li-ion battery to carry liquid electrolytes while preventing short-circuiting between electrodes. Nevertheless, conventional commercial separators often exhibit poor wettability and are prone to shrink at elevated temperatures due to their limited thermal stability. Herein, we report a heat-resistant LATP–PVDF–Al 2 O 3 composite film with outstanding wetting performance. The thin film was prepared using ball mill mixing and tape-casting processes. Two solvents, NMP and glycerol, were applied to prepare the slurry, and a favorable microstructure in the film was created after drying. Here, the ionic conductivity of the film was tested at 1.39 mS cm –1 when paired with liquid electrolyte, almost double that of the commercial counterpart. The high ceramic loading of 70% improved both the thermal shrinkage resistance and dendrite inhibition of the membrane. When assembled in an NMC half-cell, the cycling capacity retentions of 92.8% and 92.1% are achieved after 50 cycles at 0.5 C and 1 C, demonstrating its capability to be used in Li-ion batteries.
25 ENERGY STORAGE↗
Silicon Web Process Development
Silicon dendritic web, ribbon form of silicon and capable of fabrication into solar cells with greater than 15% AMl conversion efficiency, was produced from the melt without die shaping. Improvements were made both in the width of the web ribbons grown and in the techniques to replenish the liquid silicon as it is transformed to web. Through means of improved thermal shielding stress was reduced sufficiently so that web crystals nearly 4.5 cm wide were grown. The development of two subsystems, a silicon feeder and a melt level sensor, necessary to achieve an operational melt replenishment system, is described. A gas flow management technique is discussed and a laser reflection method to sense and control the melt level as silicon is replenished is examined.
Duncan, C. S.↗
Silicon web process development
A barrier crucible design which consistently maintains melt stability over long periods of time was successfully tested and used in long growth runs. The pellet feeder for melt replenishment was operated continuously for growth runs of up to 17 hours. The liquid level sensor comprising a laser/sensor system was operated, performed well, and meets the requirements for maintaining liquid level height during growth and melt replenishment. An automated feedback loop connecting the feed mechanism and the liquid level sensing system was designed and constructed and operated successfully for 3.5 hours demonstrating the feasibility of semi-automated dendritic web growth. The sensitivity of the cost of sheet, to variations in capital equipment cost and recycling dendrites was calculated and it was shown that these factors have relatively little impact on sheet cost. Dendrites from web which had gone all the way through the solar cell fabrication process, when melted and grown into web, produce crystals which show no degradation in cell efficiency. Material quality remains high and cells made from web grown at the start, during, and the end of a run from a replenished melt show comparable efficiencies.
Duncan, C. S.↗
Silicon Research and Technology Workshop report
The materials, structures, processing, modeling and measurements of high efficiency silicon solar cells were surveyed. In the materials area, highlights included: (1) the possibility of improving cell voltages by reducing minority carrier mobilities in critical regions of the solar cells; (2) the need for and possibility of lowering the surface recombination velocity for improvement of open circuit voltage in shallow junction cells; (3) the present need for improved lifetime in high resistivity cells; and (4) the potential for new materials such as polycrystalline or dendritic web material to perform well at end of life in a radiation environment. In the area of structures, distinction was made between those for terrestrial use and those that would survive radiation environments. Areas such as epitaxial growth and laser or elctron beam annealing (and diffusion) were proposed as having certain advantages over more conventional techniques.
Meulenberg, A., Jr.↗
Process research of non-CZ silicon material
Advanced processing techniques for non-CZ silicon sheet material that might improve the cost effectiveness of photovoltaic module production were investigated. Specifically, the simultaneous diffusion of liquid boron and liquid phosphorus organometallic precursors into n-type dendritic silicon web was examined. The simultaneous junction formation method for solar cells was compared with the sequential junction formation method. The electrical resistivity of the n-n and p-n junctions was discussed. Further research activities for this program along with a program documentation schedule are given.
Campbell, R. B.↗
Understanding the Influence of Li 7 La 3 Zr 2 O 12 Nanofibers on Critical Current Density and Coulombic Efficiency in Composite Polymer Electrolytes
Composite polymer electrolytes (CPEs)are attractive materials for solid-state lithium metal batteries, owing to their high ionic conductivity from ceramic ionic conductors and flexibility from polymer components. As with all lithium metal batteries, however, CPEs face the challenge of dendrite formation and propagation. Not only does this lower the critical current density (CCD) before cell shorting, but the uncontrolled growth of lithium deposits may limit Coulombic efficiency (CE) by creating dead lithium. Here, we present a fundamental study on how the ceramic components of CPEs influence these characteristics. CPE membranes based on poly-(ethylene oxide) and lithium bis-(trifluoro methane sulfonyl)-imide(PEO-LiTFSI) with Li 7 La 3 Zr 2 O 12 (LLZO) nanofibers were fabricated with industrially relevant roll-to-roll manufacturing techniques. Galvanostatic cycling with lithium symmetric cells shows that the CCD can be tripled by including 50 wt % LLZO, but half-cell cycling reveals that this comes at the cost of CE. Varying the LLZO loading shows that even a small amount of LLZO drastically lowers the CE, from 88% at 0 wt % LLZO to 77% at just 2 wt % LLZO. Mesoscale modeling reveals that the increase in CCD cannot be explained by an increase in the macroscopic or microscopic stiffness of the electrolyte; only the microstructure of the LLZO nanofibers in the PEO-LiTFSI matrix slows dendrite growth by presenting physical barriers that the dendrites must push or grow around. This tortuous lithium growth mechanism around the LLZO is corroborated with mass spectrometry imaging. In conclusion, this work highlights important elements to consider in the design of CPEs for high-efficiency lithium metal batteries.
36 MATERIALS SCIENCE↗
Fluorinated interphase enables reversible aqueous zinc battery chemistries
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
Rechargeable ambient temperature lithium cells
The cycling performance of a secondary lithium cell with a 2-methyl THF lithium hectofluorarsenate electrolyte is discussed. Stripping efficiency, dendritization, passivation on standing, and discharge efficiency are considered.
Holleck, G. L.↗
Silicon web process development
The silicon web process takes advantage of natural crystallographic stabilizing forces to grow long, thin single crystal ribbons directly from liquid silicon. The ribbon, or web, is formed by the solidification of a liquid film supported by surface tension between two silicon filaments, called dendrites, which border the edges of the growing strip. The ribbon can be propagated indefinitely by replenishing the liquid silicon as it is transformed to crystal. The dendritic web process has several advantages for achieving low cost, high efficiency solar cells. These advantages are discussed.
Duncan, C. S.↗
Cell technology: Advanced silicon sheet
The Flat-plate Solar Array (FSA)-sponsored Fourth Silicon Stress/Strain Workshop reviewed, coordinated, and assessed the progress in understanding and controlling stress and strain during the crystal growth of silicon ribbons. dislocation electrical activity and limits on solar cell efficiency, and on studying the effects of dopants on EFG characteristics. Work on silicon for high-efficiency solar cells, stress-strain relationships in silicon ribbon, and high temperature deformation of dendritic web ribbon was also discussed.
Morrison, Andrew D.↗
Methods of making and inspecting a web of vitreous lithium sulfide separator sheet and lithium electrode assemblies
A lithium ion-conductive solid electrolyte including a freestanding inorganic vitreous sheet of sulfide-based lithium ion conducting glass is capable of high performance in a lithium metal battery by providing a high degree of lithium ion conductivity while being highly resistant to the initiation and/or propagation of lithium dendrites. Such an electrolyte is also itself manufacturable, and readily adaptable for battery cell and cell component manufacture, in a cost-effective, scalable manner. An automated machine based system, apparatus and methods assessing and inspecting the quality of such vitreous solid electrolyte sheets, electrode sub-assemblies and lithium electrode assemblies can be based on spectrophotometry and can be performed inline with fabricating the sheet or web (e.g., inline with drawing of the vitreous Li ion conducting glass) and/or with the manufacturing of associated electrode sub-assemblies and lithium electrode assemblies and battery cells.
25 ENERGY STORAGE↗
O-GlcNAc transferase Ogt regulates embryonic neuronal development through modulating Wnt/β-catenin signaling
Abstract Ogt-mediated O-GlcNAcylation is enriched in the nervous system and involves in neuronal development, brain function and neurological diseases. However, the roles of Ogt and O-GlcNAcylation in embryonic neurogenesis have remained largely unknown. Here, we show that Ogt is highly expressed in embryonic brain, and Ogt depletion reduces the proliferation of embryonic neural stem cells and migration of new born neurons. Ogt depletion in cultured hippocampal neurons impairs neuronal maturation, including reduced dendritic numbers and length, and immature development of spines. Mechanistically, Ogt depletion decreases the activity of Wnt/β-catenin signaling. Ectopic β-catenin rescues neuronal developmental deficits caused by Ogt depletion. Ogt also regulates human cortical neurogenesis in forebrain organoids derived from induced pluripotent stem cells. Our findings reveal the essential roles and mechanisms of Ogt-mediated O-GlcNAc modification in regulating mammalian neuronal development.
Shen, Hui↗