Search NASA⌕ Search

SEARCH · Search NASA

Results for “depth profiling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

SIMS CHARACTERIZATION OF NITROGEN DOPING OF LCLS-II-HE PRODUCTION CAVITIES

The thermal diffusion of nitrogen into the surface of niobium has been shown to yield superior low-loss SRF performance. An effective solution was identified and promptly employed in the production of cryomodules for LCLS-II. With added experience and R&D, a modified process was chosen for use in the upgrade for LCLS-II-HE. Largely motivated by this circumstance, supporting research has significantly refined the technique for making calibrated secondary ion mass spectrometry (SIMS) measurements of the N concentration depth profiles produced by production processes. Standardized reference samples were included with four HE production cavities in their N-doping furnace runs. We report the calibrated dynamic SIMS depth profiles of N, C, and O for these samples, together with the cryogenic acceptance test performance of the associated cavities. Interpretation and comparison with similar samples acquired in other furnaces highlights the importance of intentional process quality control of furnace conditions.

Reece, Charles↗

Composition and properties of the so-called 'diamond-like' amorphous carbon films

The composition of amorphous 'diamond-like' films made by direct low energy ion beam deposition, R.F. discharge and sputtering was determined by nuclear reaction analysis, IR spectroscopy and microcombustion chemical analysis. The nuclear reaction analysis showed very similar hydrogen depth profiles for all three types of samples. The atomic ratio of hydrogen to carbon was approximately 0.2 at the film surface and rose to approximately 1.0 at a depth of 500 A. The integrated intensity of the C-H stretching band at about 2900 per cm indicates that the amount of chemically bonded hydrogen is less than the total hydrogen content. Combustion analysis confirmed the overall atomic ratio of hydrogen to carbon determined by nuclear reaction analysis. The chemical state of the non-bonded hydrogen was not determined; however, the effective diffusion coefficient computed from the hydrogen depth profile was extremely low. This indicates either that the films are exceedingly impermeable or that the non-bonded hydrogen requires an additional activated step to leave the films, e.g., desorption or chemical reaction.

Angus, J. C.↗

Investigation of Damage with Cluster Ion Beam Irradiation Using HR-RBS

Cluster ion beam can process targets with shallow damage because of the very low irradiation energy per atom. However, it is needed to investigate the damage with cluster ion beam irradiation, because recent applications demand process targets with ultra low damage. The shallow damage can be investigated from depth profiles of specific species before and after ion irradiation. They can be measured with secondary ion mass spectrometry (SIMS) and Rutherford backscattering spectroscopy (RBS). High resolution Rutherford backscattering spectroscopy (HR-RBS) is a non destructive measurement method and depth profiles can be measured with nano-resolution. The cluster ion beam mixing of thin Ni layer in carbon targets can be investigated with HR-RBS. The mixing depth with cluster ion irradiation at 10 keV was about 10 nm. The mixing depth with cluster ion irradiation at 1 keV and 5 keV were less than 1 nm and 5 nm, respectively. The number of displaced Ni atoms with cluster ion irradiation was very larger than that with monomer ion irradiation of same energy. This result shows that violent mixing occurs with single cluster impact.

74 ATOMIC AND MOLECULAR PHYSICS↗

Biosynthesis, Microstructural Characterisations and Investigation of In-Vitro Mutagenic and Eco-Toxicological Response of a Novel Microbial Exopolysaccharide Based Biopolymer

A modified microbial polysaccharide based biopolymer has been investigated as a potential candidate towards development of sustainable biomaterials and bioplastics. An in-depth study was carried out to biosynthesize, characterize and assess any possible mutagenic potential and ecotoxicity of the microbial polysaccharide biopolymer. Microstructural investigations using confocal microscopy, Fourier transform (FT)-Raman depth profile mapping and scanning electron microscopy (SEM) of the biosynthetically modified polysaccharide revealed internal structural perturbations, as well as occlusion of granular pores by extraneous materials. The Raman 3D mapping depth profile along with time-of-flight (MALDI-TOF) mass spectrometry also indicated important structural and surface modifications, which could be correlated to the production of microbial exopolysaccharides and secondary metabolites. The study then looked into any possible genetic mutation and ecological risks associated with the biosynthetically modified polysaccharide through the investigation of genotoxicity and ecotoxicity. The genotoxicity study was carried out through bacterial reverse gene mutation (Ames) test by using two different strains (TA98 and TA100) of bacteria. The results did not indicate any mutagenic effect against either of the strains used for the biopolymer samples and was found to be genotoxically safe. Ecotoxicity tests, carried out using bioluminescent bacteria Vibrio fisheri further indicated no ecotoxicity within the given experimental conditions. The study measured the half maximal effective concentration (EC50) to cause a 50% decrease in the light output of the bacteria, a measure of ecotoxicological response of the biopolymer. Overall, results from this study indicated that the novel biopolymer was genotoxically and ecotoxically safe, which offers immense potential for future use of this biopolymer.

36 MATERIALS SCIENCE↗

Impact energy and retained dose uniformity in enhanced glow discharge plasma immersion ion implantation

The implantation energy and retained dose uniformity in enhanced glow discharge plasma immersion ion implantation (EGD-PIII) is investigated numerically and experimentally. Depth profiles obtained from different samples processed by EGD-PIII and traditional PIII are compared. The retained doses under different pulse widths are calculated by integrating the area under the depth profiles. Our results indicate that the improvement in the impact energy and retained dose uniformity by this technique is remarkable.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Gold-Tin Solder Wetting Behavior for Package Lid Seals

This study examined the cause of nonwetted regions of the gold (Au) finish on iron-nickel (Fe–Ni) alloy lids that seal ceramic packages using the 80Au-20Sn solder (wt %, abbreviated Au–Sn) and their impact on the final lid-to-ceramic frame solder joint. The Auger electron spectroscopy (AES) surface and depth profile techniques identified surface and through-thickness contaminants in the Au metallization layer. In one case, the AES analysis identified background levels of carbon (C) contamination on the surface; however, the depth profile detected Fe and Ni contaminants that originated from the plating process. The Fe and Ni could impede the completion of wetting and spreading to the edge of the Au metallization. The Au layer of lids not exposed to a Au–Sn solder reflow step had significant surface and through-thickness C contamination. Inorganic contaminants were absent. Subsequent simulated reflow processes removed the C contamination from the Au layer without driving Ni diffusion from the underlying solderable layer. Finally, an Au metallization having negligible C contamination developed elevated C levels after exposure to a simulated reflow process due to C contamination diffusing into it from the underlying Ni layer. However, the second reflow step removed that contamination from the Au layer, thereby allowing the metallization to support the formation of lid-to-ceramic frame Au–Sn joints without risk to their mechanical strength or hermeticity.

36 MATERIALS SCIENCE↗

Study of Surface Damage caused by Laser Irradiation for Quantitative Hydrogen Analysis in Zircaloy using Laser-induced Plasma Breakdown Spectrometry

The surface damage caused by laser irradiation is studied to investigate the possibility of performing a depth-profile analysis of the hydrogen concentration in zircaloy-4 alloys using laser-induced plasma breakdown spectrometry. After laser irradiation, a heat-affected zone extending about 3 {mu}m down from the top surface can be seen. The depth of this heat-affected zone is independent of the laser power density in the range 10{sup 8} to 10{sup 9} W/cm{sup 2}. In order to obtain the depth profile of the hydrogen concentration in zircaloy-4 alloys, the power density of laser shots must be greater than 1.3x10{sup 9} W/cm{sup 2}.

36 MATERIALS SCIENCE↗

NanoSIMS analysis of Bacillus spores for forensics

The threat associated with the potential use of radiological, nuclear, chemical and biological materials in terrorist acts has resulted in new fields of forensic science requiring the application of state-of-the-science analytical techniques. Since the anthrax letter attacks in the United States in the fall of 2001, there has been increased interest in physical and chemical characterization of bacterial spores. While molecular methods are powerful tools for identifying genetic differences, other methods may be able to differentiate genetically identical samples based on physical and chemical properties, as well as provide complimentary information, such as methods of production and approximate date of production. Microanalysis has the potential to contribute significantly to microbial forensics. Bacillus spores are highly structured, consisting of a core, cortex, coat, and in some species, an exosporium. This structure provides a template for constraining elemental abundance differences at the nanometer scale. The primary controls on the distribution of major elements in spores are likely structural and physiological. For example, P and Ca are known to be abundant in the spore core because that is where P-rich nucleic acids and Cadipicolinic acid are located, respectively. Trace elements are known to bind to the spore coat but the controls on these elements are less well understood. Elemental distributions and abundances may be directly related to spore production, purification and stabilization methodologies, which are of particular interest for forensic investigation. To this end, we are developing a high-resolution secondary ion mass spectrometry method using a Cameca NanoSIMS 50 to study the distribution and abundance of trace elements in bacterial spores. In this presentation we will review and compare methods for preparing and analyzing samples, as well as review results on the distribution and abundance of elements in bacterial spores. We use NanoSIMS to directly image samples as well as depth profile samples. The directly imaged samples are sectioned to present a flat surface for analysis. We use focused ion beam (FIB) milling to top-cut individual spores to create flat surfaces for NanoSIMS analysis. Depth profiling can be used on whole spores, which are consumed in the process of analysis. The two methods generate comparable results, with the expected distribution of P and Ca. Ca-compatible elements, such as Mg and Mn, are found to follow the distribution of Ca. The distribution of other elements will be discussed. We envision the first application of this methodology will be to sample matching for trace samples. Towards this end, we are generating a baseline data set for samples produced by multiple laboratories. Preliminary results suggest that this method provides significant probative value for identifying samples produced by the same method in the same laboratory, as well as coming from the same initial production run. The results of this study will be presented.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhancement of the photo conversion efficiencies in Cu(In,Ga)(Se,S){sub 2} solar cells fabricated by two-step sulfurization process

Cu(In,Ga)(Se,S){sub 2} (CIGSS) absorber layers were fabricated by using a modified two-stage sputter and a sequential selenization/sulfurization method, and the sulfurization process is changed from one-step to two-step. The two-step sulfurization was controlled with two different H{sub 2}S gas concentrations during the sulfurization treatment. This two-step process yielded remarkable improvements in the efficiency (+0.7%), open circuit voltage (+14 mV), short circuit current (+0.23 mA/cm{sup 2}), and fill factor (+0.21%) of a CIGSS device with 30 × 30 cm{sup 2} in size, owing to the good passivation at the grain boundary surface, uniform material composition among the grain boundaries, and modified depth profile of Ga and S. The deterioration of the P/N junction quality was prevented by the optimized S content in the CIGSS absorber layer. The effects of the passivation quality at the grain boundary surface, the material uniformity, the compositional depth profiles, the microstructure, and the electrical characteristics were examined by Kelvin probe force microscopy, X-ray diffraction, secondary ion mass spectrometry, scanning electron microscopy, and current-voltage curves, respectively. The two-step sulfurization process is experimentally found to be useful for obtaining good surface conditions and, enhancing the efficiency, for the mass production of large CIGSS modules.

36 MATERIALS SCIENCE↗

Surface Characteristics and Hardness Variations in Electrical Discharge Machining of Enhanced Nitrogen in Vanadium Steels

Enhanced nitrogen in steels containing vanadium causes fine precipitates of vanadium nitride, which improve the hardenability properties. However, understanding the response of such steels to electrical discharge machining (EDM) is incomplete and needs further investigation. Therefore, EDM of enhanced nitrogen in steels containing vanadium was compared with a similar compositional steel that was free of nitrogen. The surface morphology, microstructural alterations, microhardness variation, and compositional depth profiling of the samples machined by EDM in oil and deionized water dielectric liquids were examined. Microscopic studies were carried out using optical and scanning electron microscopy. Phases were identified by X-ray diffractometry, and elemental depth profiling was performed using glow discharge optical emission spectroscopy. The hardness of the resolidified and heat-affected layers was measured using a Vickers type microhardness tester. The results of this study revealed that the dissolved nitrogen in steel decreased the probability of surface cracks and resulted in a softer resolidified layer structure when machining in the oil dielectric liquid. Thus, the presence of nitrogen reduced the formation of tension-induced martensite in the resolidified layer. Moreover, the heat-affected zone below the resolidified layer exhibited a uniform and harder structure, compared with the steel without nitrogen content, indicating the fast nature of the thermal cycles in EDM. The free nitrogen in steel did not dissociate during sparking; therefore, precipitation strengthening occurred in the heat-affected zone.

36 MATERIALS SCIENCE↗

Improved robustness of sequentially deposited potassium cesium antimonide photocathodes achieved by increasing the potassium content towards theoretical stoichiometry

Alkali antimonide semiconductor photocathodes are promising candidates for high-brightness electron sources for advanced accelerators, including free-electron lasers (FEL), due to their high quantum efficiency (QE), low emittance, and high temporal resolution. Two challenges with these photocathodes are (1) the lack of a universal deposition recipe to achieve crystal stoichiometries and (2) their high susceptibility to vacuum contamination, which restricts their operation pressure to ultrahigh vacuums and leads to a short lifetime and low extraction charge. To resolve these issues, it is essential to understand the elemental compositions of deposited photocathodes and correlate them to robustness. Here, we report depth profiles for potassium cesium antimonide photocathodes, which were investigated using synchrotron radiation x-ray photoelectron spectroscopy, and the robustness of those photocathodes. We prepared two types of photocathodes with different potassium contents via sequential thermal evaporation. Depth profiles revealed that the photocathodes with a potassium deficit had excess cesium at the surface, while the ratio of potassium and cesium to antimony decreased rapidly within the film. In contrast, the photocathodes with sufficient potassium had close to the theoretical stoichiometry of K 2 CsSb at the surface and maintained that stoichiometry for over half the entire film thickness. Both photocathode types had a similar maximum QE at 532 nm; however, exposure to oxygen revealed that the photocathode with a crystalline stoichiometry of K 2 CsSb maintained QE at one order of magnitude higher pressure compared to its potassium-deficit counterpart. These results highlight the importance of synthesizing potassium cesium antimonide photocathodes with sufficient potassium to achieve the theoretical crystalline stoichiometry for both high QE and improved robustness.

47 OTHER INSTRUMENTATION↗

Ion-probe studies of artificially implanted ions in lunar samples

The ion microprobe at the Johnson Space Center was used to study depth profiles of artificially implanted ions in lunar samples. Five polished sections of typical mare basalts (12040 and 12018) were irradiated with nine different elements at two energies and the resulting concentrations were measured as a function of depth in the minerals plagioclase, pyroxene, and ilmenite. These preliminary simulation experiments were undertaken to determine whether the ion probe can be used to measure solar-wind-implanted elements on the surface of lunar rock crystals and soil grains and to study mechanisms for the redistribution. The results obtained so far demonstrate that depth profiles can indeed be measured with the ion probe. From estimated exposure times of mature soil grains and selected vug crystals, it appears possible (if difficult) to detect several solar-wind-implanted elements.

Zinner, E.↗

Damage Profiles and Ion Distribution in Pt-irradiated SiC

Single crystalline 6H-SiC samples were irradiated at 150 K with 2 MeV Pt ions. The local volume swelling was determined by electron energy loss spectroscopy (EELS), and a nearly sigmoidal dependence on irradiation dose is observed. The disorder profiles and ion distribution were determined by Rutherford backscattering spectrometry (RBS), transmission electron microscopy, and secondary ion mass spectrometry. Since the volume swelling reaches 12% over the damage region at high ion fluence, the effect of lattice expansion is considered and corrected for in the analysis of RBS spectra to obtain depth profiles. Projectile and damage profiles are estimated by SRIM (Stopping and Range of Ions in Matter).When compared with the measured profiles, the SRIM code predictions of ion distribution and the damage profiles are underestimated due to significant overestimation of the electronic stopping power for the slow heavy Pt ions. By utilizing the reciprocity method, which is based on the invariance of the inelastic energy loss in ion-solid collisions against interchange of projectile and target atom, a much lower electronic stopping power is deduced. A simple approach, based on reducing the density of SiC target in SRIM simulation, is proposed to compensate the overestimated SRIM electronic stopping power values, which results in improved agreement between predicted and measured damage profiles and ion ranges.

Environmental Molecular Sciences Laboratory↗

High spatial resolution mapping of deposition layers on plasma facing materials by laser ablation microprobe time-of-flight mass spectroscopy

A laser ablation microprobe time-of-flight mass spectroscopy (LAM-TOF-MS) system with high spatial resolution, ∼20 nm in depth and ∼500 μm or better on the surface, is developed to analyze the composition distributions of deposition layers on the first wall materials or first mirrors in tokamak. The LAM-TOF-MS system consists of a laser ablation microprobe combined with a TOF-MS and a data acquisition system based on a LabVIEW program software package. Laser induced ablation combined with TOF-MS is an attractive method to analyze the depth profile of deposited layer with successive laser shots, therefore, it can provide information for composition reconstruction of the plasma wall interaction process. In this work, we demonstrate that the LAM-TOF-MS system is capable of characterizing the depth profile as well as mapping 2D composition of deposited film on the molybdenum first mirror retrieved from HL-2A tokamak, with particular emphasis on some of the species produced during the ablation process. The presented LAM-TOF-MS system provides not only the 3D characterization of deposition but also the removal efficiency of species of concern.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Observational needs for estimating Alaskan soil carbon stocks under current and future climate

Abstract Representing land surface spatial heterogeneity when designing observation networks is a critical scientific challenge. Here we present a geospatial approach that utilizes the multivariate spatial heterogeneity of soil‐forming factors—namely, climate, topography, land cover types, and surficial geology—to identify observation sites to improve soil organic carbon (SOC) stock estimates across the State of Alaska, USA. Standard deviations in existing SOC samples indicated that 657, 870, and 906 randomly distributed pedons would be required to quantify the average SOC stocks for 0–1 m, 0–2 m, and whole‐profile depths, respectively, at a confidence interval of 5 kg C m −2 . Using the spatial correlation range of existing SOC samples, we identified that 309, 446, and 484 new observation sites are needed to estimate current SOC stocks to 1 m, 2 m, and whole‐profile depths, respectively. We also investigated whether the identified sites might change under future climate by using eight decadal (2020–2099) projections of precipitation, temperature, and length of growing season for three representative concentration pathway (RCP 4.5, 6.0, and 8.5) scenarios of the Intergovernmental Panel on Climate Change. These analyses determined that 12 to 41 additional sites (906 + 12 to 41; depending upon the emission scenarios) would be needed to capture the impact of future climate on Alaskan whole‐profile SOC stocks by 2100. The identified observation sites represent spatially distributed locations across Alaska that captures the multivariate heterogeneity of soil‐forming factors under current and future climatic conditions. This information is needed for designing monitoring networks and benchmarking of Earth system model results.

54 ENVIRONMENTAL SCIENCES↗

Tritium release from SS316 under vacuum condition

The plasma facing surface of the ITER vacuum vessel, partly made of low carbon austenitic stainless steel type 316L, will incorporate tritium during machine operation. In this paper the kinetics of tritium release from stainless steel type 316 into vacuum and into a noble gas stream are compared and modelled. Type 316 stainless steel specimens loaded with tritium either by exposure to 1.2 kPa HT at 573 K or submersion into liquid HTO at 298 K showed characteristic thin surface layers trapping tritium in concentrations far higher than those determined in the bulk. The evolution of the tritium depth profile in the bulk during heating under vacuum was non-discernible from that of tritium liberated into a stream of argon. Only the relative amount of the two released tritium-species, i.e. HT or HTO, was different. Temperature-dependent depth profiles could be predicted with a one-dimensional diffusion model. Diffusion coefficients derived from fitting of the tritium release into an evacuated vessel or a stream of argon were found to be (1.4 ± 1.0)*10{sup -7} and (1.3 ± 0.9)*10{sup -9} cm{sup 2}/s at 573 and 423 K, respectively. Polished surfaces on type SS316 stainless steel inhibit considerably the thermal release rate of tritium.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

On PbTiO{sub 3}-(111)-Pt interfacial layers and their x-ray photoelectron spectroscopy signature

In this work emphasis is placed on the investigation of interfacial layers between sol-gel processed PbTiO{sub 3} (PTO) thin films and (111)Pt terminated silicon substrates. The methods used are x-ray diffraction, x-ray photoelectron spectroscopy (XPS) combined with depth profiling, and atomic force microscopy (AFM). In order to avoid artifacts related to ion bombardment, e.g., reduction of Pb ions and preferential sputtering, gentle argon ion bombardment conditions were first derived. AFM investigations of native and ion bombarded films at different stages of depth profiling show that the films are homogenously sputtered, whereby the film roughness remains practically unchanged in the course of sputtering. An annealing treatment at 550 deg. C under reducing atmosphere was used to provoke the formation of an interfacial intermetallic (111)Pt{sub x}Pb phase, which is shown to coexist with an amorphous oxide film. This could allow us to establish the XPS signature of the intermetallic phase. A negative shift of the Pt (4f) binding energy and a large full width at half maximum of the Pb (4f) peak are the attributes of this signature. PTO-film annealing in air at temperatures between 350 and 600 deg. C leads to the formation of the perovskite phase, starting at 500 deg. C, directly from the amorphous phase. Based on its derived XPS signature it is shown that the intermetallic phase still exists at the interface with variable thickness depending on the annealing temperature. The pronounced (111) texture of the PTO-crystallized films is thought to be the direct consequence of this intermetallic template layer. It is also shown that the outermost surface of the PTO film is enriched with PbO as a result of segregation phenomena.

36 MATERIALS SCIENCE↗