Search NASA⌕ Search

SEARCH · Search NASA

Results for “dielectric accelerating structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

THERMAL/STRUCTURAL ANALYSIS OF THE AXION QUANTUM METROLOGY CAVITY AND ITS COMPONENTS

This research was centered around maximizing the capability to cool dielectric material within a containment unit, or Photonic Band Gap (PBG) cavity, designed for detecting axion dark matter and identifying the unit’s thermal properties. There are multiple types of PBG cavities, but the latest version that axion researchers wish to use has been theorized to contain possible issues related to its thermal properties. Thermal conductivity is an issue with the dielectric material because it is made from alumina which is highly insulative. This is important since the research is being done in a cryogenic environment and the thermal noise affects the quantum bit used for detecting the axion to photon conversion process. Therefore, any improvements to this unit should be justified and implemented but are not entirely limited to thermal contact related aspects of PBG cavities. A prospect of using sapphire in place of alumina also exists, but this is a more expensive, less tested, and more elusive material to justify the creation of a full dielectric structure out of sapphire. Thermal aspects of the cavity were analyzed using finite element method (FEM) and an experiment designed to test different thermal joint materials. FEM was used to check the contraction of the cavity during cooling, the contact quality between the dielectric material and cavity wall, theheat flow rate through the assembly, and helps visualize the cavity’s reaction to different design changes. A simple comparison between thermal conductivity curves justified the usage of sapphire over alumina from a thermal property point of view. Thus, the method of experimentation had an additional dielectric material, sapphire, to test with and compare to alumina. The thermal test identified which material is best to use for a thermal joint but also simultaneously found the conductance of the joint and dielectric material as well as an estimate for what the temperature is inside the larger scale cavity since a thermometer cannot be placed inside the PBG when it cools. Initially, the cavity simulation was tested for structural deformation properties and stress distribution since it is made of copper which contracts heavily in comparison to most other materials. The reduction in volume of the cavity was less than anticipated which gave more room for a possible usage of a modified thermal joint for additional contact area and higher conductivity.

43 PARTICLE ACCELERATORS↗

Tunable High-Q Photonic Band Gap Cavity

We present the design of a tunable high-Q photonic band gap (PBG) cavity, made from a periodic arrangement of dielectric rods in a woodpile like structure. We know that the axion signal rate di- minishes as we move to higher axion mass searches. High quality factor achieved with this type of cavity will enable higher mass axion search with improved signal sensitivity and faster scanning rate. Quality factor in excess of the axion-Q will enable us to design interesting experiments such as the quantum non-demolition (QND) measurement of itinerant microwave photons using superconducting qubits, and stimulated emis- sion of photons.

43 PARTICLE ACCELERATORS↗

Characterization of Engineered Pinholes in Dielectric Stacks of High-Performance Poly-Silicon Passivating Contacts

Passivating contact structures are expected to be implemented in > 50 % of industrially manufactured silicon photovoltaics produced over the next decade. One type of passivating contact utilizes a c-Si/dielectric/doped poly-Si layer stack. In cases where the dielectric layer/s are thick enough to impede tunneling of charge carriers, it was shown that disruptions (pinholes) in the dielectric are required to facilitate transport.[1] Pinholes in SiOx layers have typically been formed via high temperature annealing that allows localized breakup of this layer. This approach has drawbacks; 1) high temperature annealing increases cost and 2) pinhole formation is sensitive to both the SiOx thickness and wafer surface morphology making control of density and dimensions difficult. Recently, an alternative method of pinhole formation relying on metal assisted chemical etching (MACE) was shown to allow control over pinhole areal densities.[2] Such control is critical as both the density and dimensions of the pinholes determine saturation current density and contact resistivity. The contacts formed with the MACE process are known as polysilicon on locally etched oxide or PLEO and also result in low saturation current densities and low contact resistivity due to SiOx passivation and engineered pinhole enabled charge carrier transport, respectively. Photovoltaic devices with efficiencies greater than 20 % have recently been produced with these contacts, demonstrating the viability of contacts with engineered pinholes. Experimentally, preferential local collection of excess charge carriers has been observed and definitively connected to thermally induced pinholes in thick SiOx layers within c-Si/SiOx/poly-Si contact structures.[3] Recent work has shown that enhanced local collection of excess carriers can result from enhanced diffusion of dopants through pinholes in SiOx layers.[4] This study was restricted to simulation and characterization of poly-Si with the same dopant type as the c-Si substrates. In this work we focus our analysis on boron doped poly-Si with different stacks of dielectric layers (PLEO and PLENO where the N refers to a SiNy layer on top of the SiOx) on n-type crystalline silicon. This provides insight into how engineered pinholes affect charge collection across the p-n junction. Like previous observations of locally enhanced carrier transport through thermally induced pinholes, the EBIC images in Figure 1 shows that engineered pinholes in PLENO (1a) and PLEO (1b) also exhibit locally enhanced carrier transport at pinhole locations (bright spots in the images). We will also present detailed correlative nanoscale structural and chemical analysis using TEM imaging and EELS analysis with sample preparation guided by EBIC imaging. This allows us to connect the density and dimensions of engineered pinholes with charge carrier transport and measured photovoltaic device parameters. Our findings will accelerate the adoption of PLEO and PLENO contacts in industrially manufactured photovoltaic devices.

EBIC↗

Effect of surface produced secondary electrons on the sheath structure induced by high-power microwave window breakdown

Dielectric window breakdown, whose mechanism is not thoroughly understood, is a major factor of limiting the transmission and radiation of high-power microwave on the order of 1 GW. In this paper, a one-dimensional fluid-like sheath model is developed to investigate the sheath structures formed at different gas pressures. The dominant processes during the surface flashover are isolated by this model. In vacuum, electron multipactor is self-sustained by secondary electron emission, a positive space-charge potential is formed on the dielectric surface. With increasing gas pressure, electron-neutral ionization prevails against secondary electron emission. The multipactor effect is suppressed by the shielding of plasma electrons. This leads to the sheath potential changing gradually from a positive space-charge potential to a negative space-charge potential. For argon gas pressure lower than 14 Torr, the sheath is space charge limited. A potential minimum could be formed in front of the dielectric which traps secondary electrons emitted from the wall. With the higher argon gas pressure, the number density of ions becomes comparable to that of electrons, all surface produced electrons are accelerated toward the presheath region. Therefore, the normal sheath is formed and the resulting surface flashover on the dielectric surface becomes rf-driven volumetric breakdown.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tuning microwave losses in superconducting resonators

Abstract The performance of superconducting resonators, particularly cavities for particle accelerators and micro cavities and thin film resonators for quantum computations and photon detectors, has been improved substantially by recent material treatments and technological advances. As a result, the niobium cavities have reached the quality factors Q ∼ 10 11 at 1–2 GHz and 1.5 K and the breakdown radio-frequency (rf) fields H close to the dc superheating field of the Meissner state. These advances raise the questions of whether the state-of-the-art cavities are close to the fundamental limits, what these limits actually are, and to what extent the Q and H limits can be pushed by the materials nano structuring and impurity management. These issues are also relevant for many applications using high-Q thin film resonators, including single-photon detectors and quantum circuits. This topical review outlines basic physical mechanisms of the rf nonlinear surface impedance controlled by quasiparticles, dielectric losses and trapped vortices, as well as the dynamic field limit of the Meissner state. Sections cover methods of engineering an optimum quasiparticle density of states and superfluid density to reduce rf losses and kinetic inductance by pairbreaking mechanisms related to magnetic impurities, rf currents, and proximity-coupled metallic layers at the surface. A section focuses on mechanisms of residual surface resistance, which dominates rf losses at ultra low temperatures. Microwave losses of trapped vortices and their reduction by optimizing the concentration of impurities and pinning potential are also discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A Theoretical Model for Computing Freezing Point Depression of Lithium-Ion Battery Electrolytes

Reliable prediction of freezing point depression in liquid electrolytes will accelerate the development of improved Li-ion batteries which can operate in low temperature environments. In this work we establish a computational methodology to calculate activity coefficients and liquidus lines for battery-relevant liquid electrolytes. Electronic structure methods are used in conjuction with classical molecular dynamics simulations and theoretical expressions for Born solvation energy, ion-atmosphere effects from Debye-Hückel theory and solvent entropic effects. The framework uses no a priori knowledge beyond neat solvent properties and the concentration of salt. LiPF 6 in propylene carbonate (PC), LiPF 6 in dimethyl carbonate (DMC) and LiClO 4 in DMC are investigated up to 1 molal with accuracy better than 3 °C when compared to experimental freezing point measurements. Finally, we find that the difference in freezing point depression between the propylene carbonate-based electrolyte and the dimethyl carbonate electrolytes originates from the difference in the solvent dielectric constant.

25 ENERGY STORAGE↗

Control of work functions of nanophotonic components

Work function is an essential material’s property playing important roles in electronics, photovoltaics, and more recently, in nanophotonics. We have studied effects of organic, and inorganic dielectric materials on work functions of Au films in single layered, and multilayered structures. We found that measured work function of metallic surfaces can be affected by dielectric materials situated 10–100 nm away from the metallic surface. We have found that, (i) the glass underneath ~ 50 nm gold slab reduces the work function of gold, (ii) Rh590:PMMA increases the work function of a gold film deposited on top of the polymer, and (iii) reduces it if Rh590:PMMA is deposited on top of Au. (iv) With increase of the Rh590 concentration in PMMA, n, the work function first decreases (at n < 64 g/l), and then increases (at n > 64 g/l). (v) The work function of a Fabry–Perot cavity or an MIM waveguide is almost the same as that of single Au films of comparable thickness. The experimental results can be qualitatively explained in terms of a simple model taking into account adhesion of charged molecules to a metallic surface, and formation of a double layer of charges accelerating or decelerating electrons exiting the metal and decreasing or increasing the work function.

36 MATERIALS SCIENCE↗

Recent Experiment on Wakefield Transformer Ratio Enhancement at AWA

One technique to enhance the transformer ratio beyond the ordinary limit of 2 in a collinear wakefield acceleration scheme is to use a ramped bunched train (RBT). The first experimental demonstration has been reported in [1]. However, due to the mismatch between the beam bunch length and frequency of the accelerating structure, the observed transformer ratio was only marginally above 2 in the earlier experiment. We recently revisited this experiment with an optimized bunch length using the laser stacking technique at Argonne Wakefield Accelerator (AWA) facility. A transformer ratio of 3.4 has been measured using two drive bunches. Attempting to use four drive bunches met with major challenges. In this article, measurement results and data analysis from these experiments are presented in detail.

43 PARTICLE ACCELERATORS↗

Short pulse neutron generator

Short pulse neutron generators are described herein. In a general embodiment, the short pulse neutron generator includes a Blumlein structure. The Blumlein structure includes a first conductive plate, a second conductive plate, a third conductive plate, at least one of an inductor or a resistor, a switch, and a dielectric material. The first conductive plate is positioned relative to the second conductive plate such that a gap separates these plates. A vacuum chamber is positioned in the gap, and an ion source is positioned to emit ions in the vacuum chamber. The third conductive plate is electrically grounded, and the switch is operable to electrically connect and disconnect the second conductive plate and the third conductive plate. The at least one of the resistor or the inductor is coupled to the first conductive plate and the second conductive plate.

43 PARTICLE ACCELERATORS↗

Dielectric-plate-implanted Higher Order Mode (HOM) Waveguide for High Intensity Multi-beam Device Application

A mode-selective oversized RF-beam channel has been investigated for high intensity multi-beam devices. Implanting the equi-spaced dielectric plates at the transverse positions where longitudinal electric fields of a HOM are minimal in the mic ro-metallic structure strongly suppresses all lower energy modes and other wakefield modes. The dielectric lattice captures only a single HOM of the wavelengths that correspond to the plate spacing. Electromagnetic simulations have shown that the lower en ergy modes, TE10 and TE20 modes, are suppressed down to < ~ -60 dB by two plate loads, while TE310-mode prominently propagates through the 2 mm long waveguide only with 4 dB (= -2dB/mm) at 1 THz. The numerical calculation indicated that the TE30 mode has ~ a few times higher Q than the lower energy modes. The strong single mode selectivity has been extensively looked into with a more highly overmoded structure. Feasibility analysis of the HOM structure for multi-beam device application is under investiga tion. Particle-in-cell (PIC) simulation has shown coherent beam bunching and energy gain from THz driving signal.

43 PARTICLE ACCELERATORS↗

The Effect of an Oxide Layer on Resistive-Wall Wakefields

Shorter and shorter electron bunches are now used in the FEL designs. The fine structure of the wall of a beam vacuum pipe plays more noticeable role in the wake field generation. Additionally to the resistance and roughness, the wall may have an oxide layer, which is usually a dielectric. It is important for aluminium pipe, which have Al2O3 layer. The thickness of this layer may vary in a large range: 1-100 nm. We study this effect for the very short (20-1000 nm) ultra relativistic bunches in an infinite round pipe. We solved numerically the Maxwell equations for the fields in the metal and ceramics. Results showed that the oxide layer may considerably increase the wavelength and the decay time of the resistive-wall wake fields, however the loss factor of the very short bunches does not change much.

43 PARTICLE ACCELERATORS↗

A tutorial on high-order harmonic generation in atoms, molecules, and condensed matter

This tutorial introduces strong-field-driven high-order harmonics, their experimental generation and characterization techniques, and their main applications including attosecond pulse generation and ultrafast spectroscopy of the target material. We begin from the use of atomic targets, where the first high-order harmonic generation (HHG) experiments were realized in the late 1980s. Then, we briefly discuss the basics of the microscopic generation mechanism and how various steps of the mechanism were exploited in applications such as generating isolated attosecond pulses and probing molecular orbitals. We introduce and describe the standard experimental approaches for condensed phase HHG, where we discuss unique technical challenges of the use of solid-state materials, such as the mitigation of plasma formation and laser damage. We cover the fundamentals of high-harmonic spectroscopy in condensed matter systems, such as wide bandgap dielectrics, semiconductors, liquid media, and 2D-crystals. We provide some examples of rapidly emerging spectroscopic capabilities, such as for probing crystal symmetries, Berry phases, and associated non-trivial topological properties of the source material. Finally, we provide an overview of the research field, including some of the challenges, opportunities, and open questions.

Attosecond pulses↗

Fluoroethylenepropylene ferroelectret films with cross-tunnel structure for piezoelectric transducers and micro energy harvesters

Layered fluoroethylenepropylene (FEP) ferroelectret films with cross-tunnel structure were fabricated from sheets of FEP films by template-patterning followed by a fusion-bonding process and contact charging. The typical piezoelectric d{sub 33} coefficients, measured by a quasi-static method of samples not annealed, are in the range of 1000–3700 pC/N. The resonance behavior of the samples is analyzed by dielectric spectroscopy which also yields Young's modulus. Microphones built with such films exhibit a somewhat decreasing frequency response up to 1 kHz, an increase of the responses due to diffraction effects at higher frequencies, and eventually a peak probably due to a thickness resonance at about 40 kHz. Annealing at 125 °C indicates that the sensitivity stabilizes at about 40% of the original value. From this data, stable dynamic d{sub 33} coefficients of up to 300 pC/N can be calculated. A micro energy harvesting generator utilizing these films and based on the excitation of thickness vibrations is also described. With an active area of 4.3 cm{sup 2} and a seismic mass of 69.5 g, power up to 0.5 μW referred to an acceleration of 1 g can be generated at a frequency of 120 Hz.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Linear permittivity tapering in a Cerenkov microwave source with a pre-bunched beam

Cerenkov microwave sources use a dielectric-lined waveguide to reduce the velocity of the electromagnetic wave and provide efficient energy transfer between the wave and the driving electron beam. Tapering the permittivity of the dielectric to maintain synchronism between the beam and the wave as the beam loses energy can increase the efficiency of these devices. Here, we consider such a structure driven by an electron beam with a harmonic density perturbation. Particle-In-Cell (PIC) simulations and a macro-particle model based on the slowly varying envelope approximation are first used to examine an un-tapered baseline case. PIC simulations of the source with linear tapers over the entire amplifier length as well as over only a section of the amplifier where the beam executes synchrotron oscillations are examined. The efficiency for the baseline un-tapered source is 18%, while efficiencies up to approximately 48% are found using a taper in dielectric permittivity. Results of the best performing cases are presented. Detailed examination of longitudinal phase space, particle energy distributions, evolution of longitudinal wavenumber, and phase dynamics are presented from the PIC simulations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Microwave-assisted pyrolysis of liquid hydrocarbons using iron-based alumina catalysts obtained by solution combustion synthesis: The effect of synthesis parameters

The microwave-absorbing and catalytic properties of iron-based alumina (FeAl x O y ) materials have enabled their use as catalysts for the microwave-assisted generation of hydrogen and carbon via pyrolysis of hydrocarbons. Solution combustion synthesis (SCS) is a promising method to fabricate these materials, but the pyrolysis performance still needs to be improved. The present work investigated how altering the SCS parameters affects the pyrolysis of diesel fuel, gasoline, and crude oil. Two fuels (citric acid and glycine), four Fe:Al molar ratios, and two heating modes (hotplate and furnace) were tested. Fe/γ-Al 2 O 3 and Fe/β-SiC catalysts were prepared via incipient wetness impregnation for comparison. Among the three fossil fuels tested, diesel fuel yielded the highest amounts of H 2 and least amounts of CO x . The choice of fuel for the SCS process and the Fe/Al ratio strongly affected pyrolysis performance as they influence properties important for both catalysis and microwave absorption. The use of glycine resulted in catalysts that exhibited high H 2 yield and low CO 2 generation, which is explained by the revealed structural differences. The increase in the Fe:Al molar ratio accelerated microwave heating by adding more magnetic loss but also increased the amount of CO x . When the optimal SCS parameters were used, FeAl x O y catalysts outperformed Fe/γ-Al 2 O 3 and Fe/β-SiC. The high H 2 generation efficiency of the SCS catalysts is explained by their enhanced microwave-absorption properties. Scanning electron microscopy and energy dispersive X-ray spectroscopy revealed the formation of large-diameter CNTs via the tip-growth mechanism. The regeneration of SCS catalysts was demonstrated via the Boudouard reaction.

Carbon nanotubes↗

Relaxation Dynamics and Ion Conduction of Poly(Ethylene Carbonate/Ethylene Oxide) Copolymer-Based Electrolytes

Poly(ethylene carbonate/ethylene oxide) P(EC/EO) copolymer was synthesized from EC monomer as a new matrix component of solid polymer electrolytes (SPEs), and the correlation between polymer dynamics and ionic conductivity in the P(EC/EO)-based SPEs at various lithium salt weight fractions (w Li ) was investigated by dielectric spectroscopy, rheology, and molecular dynamics (MD) simulations. With the addition of lithium salt, the molecular motions at various scales (i.e., from local to segmental and global motion scales) were found to change as follows: (i) the local motion of P(EC/EO) was slightly accelerated, and at w Li ≥ 0.22, it was separated into two relaxation modes, one faster and the other slower than that of P(EC/EO), (ii) the segmental motion of P(EC/EO) became significantly slower with the addition of lithium salt, and (iii) the global terminal relaxation became slightly slower with the increase of w Li . Thus, the motion of P(EC/EO) at various scales in SPEs changed with different trends with increasing lithium salt. It was also found that the temperature dependence of the ionic conductivity was described by a Vogel–Fulcher–Tammann-type function, which was correlated with the segmental motion, as is known in other SPE systems. Furthermore, from MD simulations, lithium ions are coordinated with the EC units more likely and with a closer distance than EO units in P(EC/EO), and the coordination number of oxygens around one lithium ion was estimated as 6–7 at the distance of 0.30 nm. Here, these results suggest that the coordination structure of the oxygens around the lithium ion is slightly disrupted due to the presence of EC units compared to the chelating structure of pure PEO electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Strain-induced lead-free morphotropic phase boundary

Enhanced susceptibilities in ferroelectrics often arise near phase boundaries between competing ground states. While chemically-induced phase boundaries have enabled ultrahigh electrical and electromechanical responses in lead-based ferroelectrics, precise chemical tuning in lead-free alternatives, such as (K,Na)NbO 3 thin films, remains challenging due to the high volatility of alkali metals. Here, we demonstrate strain-induced morphotropic phase boundary-like polymorphic nanodomain structures in chemically simple, lead-free, epitaxial NaNbO 3 thin films. Combining ab initio simulations, thin-film epitaxy, scanning probe microscopy, synchrotron X-ray diffraction, and electron ptychography, we reveal a labyrinthine structure comprising coexisting monoclinic and bridging triclinic phases near a strain-induced phase boundary. The coexistence of energetically competing phases facilitates field-driven polarization rotation and phase transitions, giving rise to a multi-state polarization switching pathway and large enhancements in dielectric susceptibility and tunability across a broad frequency range. Our results open new possibilities for engineering lead-free thin films with enhanced functionalities for next-generation applications.

Electronic properties and materials↗

Microbial Vessel for Impedance Spectroscopy and Electrochemistry (Mvise): an Extensible, Interoperable Data Acquisition Platform for Liquid Culture Studies in Space Biology Research

The White House Office of Science and Technology Policy (OSTP) has declared 2023 to be the Year of Open Science following an initiative to democratize scientific knowledge. Simultaneously, new sensor technologies have broadened the experimental space available to bioastronautics research. With these open-science goals and technological advances in mind, we have designed and constructed a data acquisition platform for high-precision, real-time monitoring of liquid culture systems. The vessel rig is fitted with six Atlas Scientific probes (micro pH, electrical conductivity, dissolved oxygen, oxidation-reduction potential, liquid temperature, air CO2) and a custom optical density probe similar to the one on BioSentinel’s BioSensor payload. A custom dielectric spectroscopy probe is also planned. The structure of the vessel is resin 3-D printed on a hobbyist-level machine, reducing the production cost and iteration time by over 60% each while increasing extensibility. Data acquisition and storage is controlled with a standalone C state machine-based program running on a Raspberry Pi 3 Model B. When not running headless, an additional program automatically generates and updates plots for live data visualization. Validation of the rig as a data collection system was performed with a yeast liquid culture experiment. While the vessel rig is currently used for standalone experiments, it can also be used as the base perception unit in a self-driving laboratory (SDL). SDLs are high-throughput data collection systems that employ automation and artificial intelligence to conduct and manage routine experiments. Here, we envision an SDL driven by several vessel rigs in which an automated script compares key results, informing the design of future experiments. A vessel rig SDL would streamline many operations, including 1) strain selection for the Lunar Explorer Instrument for space biology Applications (LEIA) investigation and 2) the study of bioregenerative life support systems (BLSS). Ultimately, the datasets that can now be acquired will provide crucial information for accelerating bioastronautics application development in the era of commercial space.

Stephen Lantin↗