Search NASA⌕ Search

SEARCH · Search NASA

Results for “divided differences”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Airplane automatic control force trimming device for asymmetric engine failures

The difference in dynamic pressure in the propeller slipstreams as measured by sensors is divided by the freestream dynamic pressure generating a quantity proportional to the differential thrust coefficient. This quantity is used to command an electric trim motor to change the position of trim tab thereby retrimming the airplane to the new asymmetric power condition. The change in position of the trim tab produced by the electric trim motor is summed with the pilot's input to produce the actual trim tab position.

Stewart, Eric C.↗
NASA NTRS1990

On the average rate of growth in sunspot number and the size of the sunspot cycle

The average rate of growth in sunspot number over selected time intervals and the maximum average value as they both relate to the size of the cycle are examined, in order to predict the size of cycle 22. The predictions are compared with those of Wilson (1990) to determine whether a consensus is apparent. The average rate of growth during the ascending portion of the sunspot cycle, defined as the difference in smoothed sunspot number values between elapsed time t and sunspot minimum divided by t, is shown to correlate with the size of the sunspot cycle, especially for t greater or equal to 18 months. The maximum value of the average rate of growth is also shown to highly correlate (r = 0.98) with the size of the cycle. Using 4.5 as the maximum value of the average rate of growth, a lower limit for R(M) is estimated. The results show that the findings are consistent with the previous single variate predictions for R(M) for cycle 22.

Wilson, Robert M.↗
NASA NTRS1998

Computer Modeling of the Thermal Conductivity of Cometary Ice

The main objective of this research was to estimate the thermal conductivity of cometry ices from computer simulations of model amorphous ices. This was divided into four specific tasks: (1) Generating samples of amorphous water ices at different microporosities; (2) Comparing the resulting molecular structures of the ices with experimental results, for those densities where data was available; (3) Calculating the thermal conductivities of liquid water and bulk amorphous ices and comparing these results with experimentally determined thermal conductivities; and (4) Investigating how the thermal conductivity of amorphous ice depends upon the microscopic porosity of the samples. The thermal conductivity was found to be only weakly dependent on the microstructure of the amorphous ice. In general, the amorphous ices were found to have thermal conductivities of the same order of magnitude as liquid water. This is in contradiction to recent experimental estimates of the thermal conductivity of amorphous ice, and it is suggested that the extremely low value obtained experimentally is due to larger-scale defects in the ice, such as cracks, but it is not an intrinsic property of the bulk amorphous ice.

Bunch, Theodore E.↗
NASA NTRS2002

A New Domain Decomposition Approach for the Gust Response Problem

A domain decomposition method is developed for solving the aerodynamic/aeroacoustic problem of an airfoil in a vortical gust. The computational domain is divided into inner and outer regions wherein the governing equations are cast in different forms suitable for accurate computations in each region. Boundary conditions which ensure continuity of pressure and velocity are imposed along the interface separating the two regions. A numerical study is presented for reduced frequencies ranging from 0.1 to 3.0. It is seen that the domain decomposition approach in providing robust and grid independent solutions.

Scott, James R.↗
NASA NTRS2000

Efficacy of Wrist/Palm Warming as an EVA Countermeasure to Maintain Finger Comfort in Cold Conditions During EVA

This study explored the effectiveness of local wrist/palm warming as a potential countermeasure for providing finger comfort during extended duration EVA. Methods: Six subjects (5 males and 1 female) were evaluated in a sagitally divided liquid cooling/warming garment (LCWG) with modified liquid cooling/warming (LCW) gloves in three different experimental conditions. Condition 1: Stage 1- no LCWG; chamber adaptation with LCW glove inlet water temperature 33 C; Stage 2-LCW glove inlet water temperature cooled to 8 C; Stage 3-LCW glove inlet water temperature warmed to 45 C; Condition 2: Stage1-LCWG and LCW glove inlet water temperature 33 C; Stage 2-LCWG inlet temperature cooled to 31 C, LCW gloves, 8 C; Stage 3-LCWG inlet water temperature remains at 31 C, LCW glove inlet water temperature warmed to 45 C; Condition 3: Stage l -LCWG and LCW gloves 33 C; Stage 2-LCWG inlet water temperature cooled to 28 C, LCW gloves, 8 C; Stage 3-LCWG remains at 28 C, LCW glove water temperature warmed to 45 C. Results: Wrist/palm area warming significantly increased finger temperature (Tfing) and blood perfusion in Stage 3 compared to Stage 2. The LCW gloves were most effective in increasing Stage 3 Tfing in Condition 1; and in increasing blood perfusion in Conditions 1 and 2 compared to Condition 3. Ratings of subjective perception of heat in the hand and overall body heat were higher at Stage 3 than Stage 2, with no significant differences across Conditions. Conclusions: Local wrist/palm warming was effective in increasing blood circulation to the distal extremities, suggesting the potential usefulness of this technique for increasing astronaut thermal comfort during EVA while decreasing power requirements. The LCW gloves were effective in heating the highly cooled fingers when the overall body was in a mild heat deficit.

Koscheyev, Victor S.↗
NASA NTRS2008

An Improved Wavefront Control Algorithm for Large Space Telescopes

Wavefront sensing and control is required throughout the mission lifecycle of large space telescopes such as James Webb Space Telescope (JWST). When an optic of such a telescope is controlled with both surface-deforming and rigid-body actuators, the sensitivity-matrix obtained from the exit pupil wavefront vector divided by the corresponding actuator command value can sometimes become singular due to difference in actuator types and in actuator command values. In this paper, we propose a simple approach for preventing a sensitivity-matrix from singularity. We also introduce a new "minimum-wavefront and optimal control compensator". It uses an optimal control gain matrix obtained by feeding back the actuator commands along with the measured or estimated wavefront phase information to the estimator, thus eliminating the actuator modes that are not observable in the wavefront sensing process.

adaptive optics↗
NASA NTRS2024

Residual Strength of Hypervelocity Impacted Silica

Windows in the International Space Station (ISS) are subject to ongoing micrometeoroid and orbital debris (MMOD) damage. The reliability of the windows is ensured by monitoring of damage, life prediction, and measurement of the residual strength of man-made and natural hypervelocity impacted window materials. Information on the residual strength of man-made craters and MMOD craters harvested from space shuttle windows was used to estimate strength as a function of damage dimensions and thereby derive design allowables for U.S. and Russian fused silicas used in the ISS. An effect of impact angle is apparent, with 0° impacts exhibiting the lowest strength for Russian quartz-derived silica. The crater morphology for fused silica consists of a central pit, crush zone, shallow rings, and radial cracks dividing shallow, petal-like lateral cracks (petaloids). The morphology of alkaline glass differs from that of fused silica, with a more distinct pit and pulverized region, and bell-shaped and tail-like features below the pit.

International space station,↗
NASA NTRS1992

Pulmonary and leg VO2 during submaximal exercise: implications for muscular efficiency

Insights into muscle energetics during exercise (e.g., muscular efficiency) are often inferred from measurements of pulmonary gas exchange. This procedure presupposes that changes of pulmonary O2 (VO2) associated with increases of external work reflect accurately the increased muscle VO2. The present investigation addressed this issue directly by making simultaneous determinations of pulmonary and leg VO2 over a range of work rates calculated to elicit 20-90% of maximum VO2 on the basis of prior incremental (25 or 30 W/min) cycle ergometry. VO2 for both legs was calculated as the product of twice one-leg blood flow (constant-infusion thermodilution) and arteriovenous O2 content difference across the leg. Measurements were made 3-5 min after each work rate imposition to avoid incorporation of the VO2 slow component above the lactate threshold. For all 17 subjects, the slope of pulmonary VO2 (9.9 +/- 0.2 ml O2.W-1.min-1) was not different (P greater than 0.05) from that for leg VO2 (9.2 +/- 0.6 ml O2.W-1.min-1). Estimation of "delta" efficiency (i.e., delta work accomplished divided by delta energy expended, calculated from slope of VO2 vs. work rate and a caloric equivalent for O2 of 4.985 cal/ml) using pulmonary VO2 measurements (29.1 +/- 0.6%) was likewise not significantly different (P greater than 0.05) from that made using leg VO2 measurements (33.7 +/- 2.4%). These data suggest that the net VO2 cost of metabolic "support" processes outside the exercising legs changes little over a relatively broad range of exercise intensities. Thus, under the conditions of this investigation, changes of VO2 measured from expired gas reflected closely those occurring within the exercising legs.

Non-NASA Center↗
NASA NTRS1980

The effect of a nonuniform planetary albedo on the interpretation of earth radiation budget observations

The flux density measured at satellite altitude with a fixed field of view radiometer differs from the true flux density reflected by the earth-atmosphere system within the field of view of the radiometer. This difference is due to angular response characteristics of the radiometer, solid angle effects due to geometry, and angular reflectance effects of the earth-atmosphere system. All of these effects lead to uncertainties in the interpretation of instantaneous earth radiation budget measurements. The differences between the true flux density and the measured flux density are shown to be significant when the field of view of the radiometer is large and when the atmosphere has a nonuniform, or spatially dependent, reflectance (albedo). A simulation experiment is described whereby the scene within the field of view of a nadir looking sensor is divided into a large number of equal area elements, each of which reflects radiation with one of two different reflectance models (corresponding to cloud-free and cloudy areas). The conditional mean values of the measured flux density, given values of the true flux density, are shown to differ significantly from the conditional means of the inverse problem, that of finding the mean value of the true flux density given a value for the measured flux density. The differences between the true flux density and the measured flux density are examined as a function of satellite altitude, field of view of the radiometer and solar zenith angle (including the effects of a terminator within the field of view) for both Lambertian and non-Lambertian reflectance models.

King, M. D.↗
NASA NTRS2015

Transient Gene and miRNA Expression Profile Changes of Confluent Human Fibroblast Cells in Space

Microgravity or an altered gravity environment from the static 1 gravitational constant has been shown to influence global gene expression patterns and protein levels in cultured cells. However, most of the reported studies conducted in space or using simulated microgravity on the ground have focused on the growth or differentiation of the cells. Whether non-dividing cultured cells will sense the presence of microgravity in space has not been specifically addressed. In an experiment conducted on the International Space Station, confluent human fibroblast cells were fixed after being cultured in space for 3 and 14 days for investigations of gene and miRNA (microRNA) expression profile changes in these cells. A fibroblast is a type of cell that synthesizes the extracellular matrix and collagen, the structural framework for tissues, and plays a critical role in wound healing and other functions. Results of the experiment showed that on Day 3, both the flown and ground cells were still proliferating slowly even though they were confluent, as measured by the expression of the protein Ki-67 positive cells, and the cells in space grew slightly faster. Gene and miRNA expression data indicated activation of NF(sub kappa)B (nuclear factor kappa-light-chain-enhancer of activated B cells) and other growth related pathways involving HGF and VEGF in the flown cells. On Day 14 when the cells were mostly non-dividing, the gene and miRNA expression profiles between the flight and ground samples were indistinguishable. Comparison of gene and miRNA expressions in the Day 3 samples in respect to Day 14 revealed that most of the changes observed on Day 3 were related to cell growth for both the flown and ground cells. Analysis of cytoskeleton changes by immunohistochemistry staining of the cells with antibodies for alpha-tubulin showed no difference between the flight and ground samples. Results of our study suggest that in true non-dividing human fibroblast cells, microgravity in space has little effect on the gene and miRNA expression. Gene and miRNA expression changes were observed in cells that were confluent, but still proliferating slowly. The faster growth in the flown cells was associated with the activation of NF(sub kappa)B pathways which triggers the expression of several growth factors and the suppression of the cell cycle checkpoint.

Zhang, Ye↗
NASA NTRS1972

Seat belt restraint system

Shoulder-harness and lap-belt restraint system was designed to be worn by individuals of widely different sizes and to permit normal body motion except under sudden deceleration. System is divided into two basic assemblies, lap belt and torso or shoulder harness. Inertia-activated reels immediately lock when seat experiences sudden deceleration.

Garavaglia, A.↗
NASA NTRS1978

Use of computers to exclude the influence of radiometer instability upon measurement results

A radiometer, practically insensitive to great fluctuations in the equipment amplification coefficient, was developed by dividing the useful signal by a reference signal and modulating the two signals at different frequencies. The signals are simultaneously separated by corresponding synchronous detectors and recorded over two channels. The operation is simplified by replacing the continuous signals by a sampling of discrete values, and using a digital computer. The four steps involved in the process are described and a block diagram is included. This technique not only directly connects the radiometer with the computer, but also records all data provided by the control and signal channels.

Domnin, S. L.↗
NASA NTRS1993

Outgassing Data for Selecting Spacecraft Materials

This tenth compilation of outgassing data of materials intended for spacecraft use supersedes Reference Publication 1124, Revision 2, November 1990. The data were obtained at the Goddard Space Flight Center (GSFC), utilizing equipment developed at Stanford Research Institute (SRI) under contract to the Jet Propulsion Laboratory (JPL). SRI personnel developed an apparatus for determining the mass loss in vacuum and for collecting the outgassed products. The outgassing data have been presented in three different ways in order to facilitate material selection. In Section A, the materials are divided by category into the 18 probable uses, such as adhesives, greases, paints, potting compounds, and so forth. In Section B, all the materials contained in Section A are listed in alphabetical order by the manufacturer's identification. In Section C, the only materials listed are those having 'Total Mass Loss' (TML) and Collected Volatile Condensable Materials (CVCM) equal to or lower than a maximum 1.0 percent TML and a maximum 0.10 percent CVCM. These are grouped by use, as in Section A.

Campbell, William A., Jr.↗
NASA NTRS1995

Estimating release of carbon from 1990 and 1991 forest fires in Alaska

An improved method to estimate the amounts of carbon released during fires in the boreal forest zone of Alaska in 1990 and 1991 is described. This method divides the state into 64 distinct physiographic regions and estimates areal extent of five different land covers: two forest types, peat land, tundra, and nonvegetated. The areal extent of each cover type was estimated from a review of topographic maps of each region and observations on the distribution of foreat types within the state. Using previous observations and theoretical models for the two forest types found in interior Alaska, models of biomass accumulation as a function of stand age were developed. Stand age distributions for each region were determined using a statistical distribution based on fire frequency, which was from available long-term historical records. Estimates of the degree of biomass combusted were based on recent field observations as well as research reported in the literature. The location and areal extent of fires in this region for 1990 and 1991 were based on both field observations and analysis of satellite (advanced very high resolution radiometer (AVHRR)) data sets. Estimates of average carbon release for the two study years ranged between 2.54 and 3.00 kg/sq m, which are 2.2 to 2.6 times greater than estimates used in other studies of carbon release through biomass burning in boreal forests. Total average annual carbon release for the two years ranged between 0.012 and 0.018 Pg C/yr, with the lower value resulting from the AVHRR estimates of fire location and area.

Kaisischke, Eric S.↗
NASA NTRS2008

Space Transportation System Availability Requirements and Its Influencing Attributes Relationships

It is essential that management and engineering understand the need for an availability requirement for the customer's space transportation system as it enables the meeting of his needs, goal, and objectives. There are three types of availability, e.g., operational availability, achieved availability, or inherent availability. The basic definition of availability is equal to the mean uptime divided by the sum of the mean uptime plus the mean downtime. The major difference is the inclusiveness of the functions within the mean downtime and the mean uptime. This paper will address tIe inherent availability which only addresses the mean downtime as that mean time to repair or the time to determine the failed article, remove it, install a replacement article and verify the functionality of the repaired system. The definitions of operational availability include the replacement hardware supply or maintenance delays and other non-design factors in the mean downtime. Also with inherent availability the mean uptime will only consider the mean time between failures (other availability definitions consider this as mean time between maintenance - preventive and corrective maintenance) that requires the repair of the system to be functional. It is also essential that management and engineering understand all influencing attributes relationships to each other and to the resultant inherent availability requirement. This visibility will provide the decision makers with the understanding necessary to place constraints on the design definition for the major drivers that will determine the inherent availability, safety, reliability, maintainability, and the life cycle cost of the fielded system provided the customer. This inherent availability requirement may be driven by the need to use a multiple launch approach to placing humans on the moon or the desire to control the number of spare parts required to support long stays in either orbit or on the surface of the moon or mars. It is the intent of this paper to provide the visibility of relationships of these major attribute drivers (variables) to each other and the resultant system inherent availability, but also provide the capability to bound the variables providing engineering the insight required to control the system's engineering solution. An example of this visibility will be the need to provide integration of similar discipline functions to allow control of the total parts count of the space transportation system. Also the relationship visibility of selecting a reliability requirement will place a constraint on parts count to achieve a given inherent availability requirement or accepting a larger parts count with the resulting higher reliability requirement. This paper will provide an understanding for the relationship of mean repair time (mean downtime) to maintainability, e.g., accessibility for repair, and both mean time between failure, e.g., reliability of hardware and the system inherent availability. Having an understanding of these relationships and resulting requirements before starting the architectural design concept definition will avoid considerable time and money required to iterate the design to meet the redesign and assessment process required to achieve the results required of the customer's space transportation system. In fact the impact to the schedule to being able to deliver the system that meets the customer's needs, goals, and objectives may cause the customer to compromise his desired operational goal and objectives resulting in considerable increased life cycle cost of the fielded space transportation system.

Rhodes, Russel E.↗
NASA NTRS2012

Two Distinct Modes in One-Day Rainfall Event during MC3E Field Campaign: Analyses of Disdrometer Observations and WRF-SBM Simulation

A unique microphysical structure of rainfall is observed by the surface laser optical Particle Size and Velocity (Parsivel) disdrometers on 25 April 2011 during Midlatitude Continental Convective Clouds Experiment (MC3E). According to the systematic differences in rainfall rate and bulk effective droplet radius, the sampling data can be divided into two groups; the rainfall mostly from the deep convective clouds has relatively high rainfall rate and large bulk effective droplet radius, whereas the reverse is true for the rainfall from the shallow wrm clouds. The Weather Research and Forecasting model coupled with spectral bin microphysics (WRF-SBM) successfully reproduces the two distinct modes in the observed rainfall microphysical structure. The results show that the up-to-date model can demonstrate how the cloud physics and the weather condition on the day are involved in forming the unique rainfall characteristic.

disdrometers↗
NASA NTRS2016

Retrieval of Daily Maps of PM2.5 Aerosol in the Problematic California Valleys: Bright, Speckled Reflectances, Thin AOT, but High Pollution

The San Joaquin Valley suffers from severe episodes of respirable aerosol (PM2.5) in wintertime.We provide maps of aerosol episodes using daily snapshots of PM2.5 and its changing features despite numerous difficulties inherent to sampling the region. Linear relationships relating aerosol optical thickness (AOT) to PM2.5 give an explained variance of approximately 3.The GEO-CAPE mission has as a goal the provision of relevant measures of respirable aerosol to the community,but has not formulated a science goal beyond the limited goal of retrieval of AOT, bringing the usefulness of GEO-CAPE into doubt.Our special focus was on the DISCOVER-AQ period, Jan-Feb 2013, which had many supporting measurements.Both high pollution and retrieval difficulties tend to occur in many Mediterranean agricultural regions like the San Joauin. One difficulty is the relatively bright surfaces with considerable exposed soil. NASAs MAIAC and MODIS Deep Blue retrieval techniques are shown to have considerable skill even at low aerosol optical thickness (AOT) values, as evaluated by concurrent AERONET sunphotometer measurements.More significantly, these AOT values can correspond to high daytime PM2.5 since aerosol mixed layer depth is thin and variable, 200m 600 m. The thin layers derive from typical subsidence of dry air between more stormy periods. This situation provides an advantage: water vapor column is also almost completely limited to a similar mixed layer depth, and can thus serve as a measure of aerosol dilution.Using the MAIAC Water Vapor Column:In order to make the maps below, we used the MAIAC data but subtracted partial water-vapor columns estimated from MERRA Reanalysis Data availabe from the GSFC GMAO using kriging. We did not use the mixed-layer estimates from MERRA, since such analyses were found problematic during our forecasting exercises for DISCOVER-AQ. Observations from the aircraft soundings suggested that this overlying moisture was mostly due to larger scale flows, not ML venting.However, the specific humidity at the surface and a nearly well-mixed ML was analyzed by kriging from the surface network (MesoWest, University of Utah). These were thought to be truer, uninfluenced by physical process modeling that combines with data observations. (TBD: How different are they?) Procedure: Subtract overlying partial water columns from MAIAC column water and divide this by a surface value of water vapor. (MAIAC column is expressed in cm of water, i.e., water vapor at surface conditions.This method appears to bring out useful details in the distribution of submicron particles in the very problematic Wintertime San Joaquin Valley, and allow analysis of pollution episodes throughout the valley, rather than long-term averages.

san joaquin valley↗
NASA NTRS2016

A DSMC Surface Chemistry Model for Carbon-Based Ablators

A detailed molecular surface chemistry model for the DSMC (Direct Simulation Monte Carlo) method is proposed and implemented into the SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) DSMC solver. Molchanova et al. constructed a molecular model for surface recombination in DSMC that includes different surface processes (adsorption, desoprtion, Eley-Rideal and Langmuir-Hinshelwood). All surface processes can be divided into two groups: surface mechanisms, which involve only the particle adsorbed by the surface (desorption and Langmuir-Hinshelwood), and impact mechanisms, which also involve gas-phase particles (adsorption, Eley-Rideal). Using a similar approach, the 14-reaction kinetic model of oxygen-carbon interaction suggested by Zhlukhtov and Abe, as well as more recent models by Alba et al., Poovathinghal et al., and a new model developed in the scope of this work, are implemented in SPARTA. The computational results for the different oxidation models are compared with experimental results from Murray et al. (oxidation of a vitreous carbon surface due to a hyperthermal beam of O and O2), with a particular focus on fluxes, angular and Time-Of-Flight distributions of scattered particles.

oxidation↗