Search NASA⌕ Search

SEARCH · Search NASA

Results for “drop size”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

The meteorological parameterization of specific attenuation in rain viewed at Nadir

Polynomial expressions are presented for the parameterization of the specific attenuation in rain from 9 to 38 GHz that are applicable to a wide range of naturally occurring drop size distributions and for viewing angles close to nadir. Because the temperature T affects the specific attenuation at some frequencies, expressions for the polynomial coefficients as functions of T are also provided for -10C less than or equal to T less than or equal to 30C. The advantage of this parameterization is that even without a detailed specification of the drop size distribution, useful estimates of the specific attenuation are often possible given only two out of three parameters, namely, the rainfall rate R, the rainwater content W, or D(sub m) (the mass-weighted mean drop diameter), particularly if the temperature is also specified.

Jameson, A. R.↗
NASA NTRS1989

Numerical modeling for primary atomization of liquid jets

In the proposed numerical model for primary atomization, surface-wave dispersion equations are solved in conjunction with the jet-embedding technique of solving mean flow equations of a liquid jet. Linear and approximate nonlinear models have been considered. In each case, the dispersion equation is solved over the whole wavelength spectrum to predict drop sizes, frequency, and liquid-mass breakup rates without using any empirical constants. The present model has been applied to several low-speed and high-speed jets. For the high-speed case (the LOX/H2 coaxial injector of the Space Shuttle Main Engine Preburner), predicted drop sizes and liquid breakup rates are in good agreement with the results of the CICM code, which have been calibrated against measured data.

Przekwas, A. J.↗
NASA NTRS1980

Atomizing characteristics of swirl can combustor modules with swirl blast fuel injectors

Cold flow atomization tests of several different designs of swirl can combustor modules were conducted in a 7.6 cm diameter duct at airflow rates (per unit area) of 7.3 to 25.7 g/sq cm sec and water flow rates of 6.3 to 18.9 g/sec. The effect of air and water flow rates on the mean drop size of water sprays produced with the swirl blast fuel injectors were determined. Also, from these data it was possible to determine the effect of design modifications on the atomizing performance of various fuel injector and air swirler configurations. The trend in atomizing performance, as based on the mean drop size, was then compared with the trends in the production of nitrogen oxides obtained in combustion studies with the same swirl can combustors.

Ingebo, R. D.↗
NASA NTRS1983

Differential reflectivity (Z-DR) measurements of rainfall compared with ground-based disdrometer measurements

The dual-polarization differential-reflectivity (Z-DR) radar technique of Seliga and Bringi (1976) is used to determine rainfall rates and drop sizes over a site located at a distance of 47.1 km, and the results are analyzed using the empirical calibration relations of Seliga et al. (1983) and compared with electromechanical-disdrometer measurements. The data are presented in graphs and found to be well correlated, demonstrating the validity of the Z-DR estimates and the improvement introduced by applying the empirical relations rather than an a priori drop-size distribution.

Direskeneli, H.↗
DOE OSTI2020

Observations Pertaining to Precipitation within the Northeast Pacific Stratocumulus-to-Cumulus Transition

Three genuine stratocumulus-to-cumulus transitions sampled during the Cloud System Evolution over the Trades (CSET) campaign are documented. The focus is on Lagrangian evolution of in situ precipitation, thought to exceed radar/lidar retrieved values because of Mie scattering. Two of the three initial stratocumulus cases are pristine [cloud droplet number concentrations ($N_d$) of ~22 cm –3 ] but occupied boundary layers of different depths, while the third is polluted ($N_d$ ~ 225 cm –3 ). Hourly satellite-derived cloud fraction along Lagrangian trajectories indicate that more quickly deepening boundary layers tend to transition faster, into more intense but more occasional precipitation. These transitions begin either in the morning or late afternoon, suggesting that preceding night processes can precondition or delay the inevitable transition. The precipitation shifts toward larger drop sizes throughout the transition as the boundary layers deepen, with aerosol concentrations only diminishing in two of the three cases. Ultraclean ($N_d$ < 1 cm –3 ) cumulus clouds evolved from pristine stratocumulus cloud with unusually high precipitation rates occupying a shallow, well-mixed boundary layer. Results from a simple one-dimensional evaporation model and from radar/lidar retrievals suggest subcloud evaporation likely increases throughout the transition. This, coupled with larger drop sizes capable of lowering the latent cooling profile, facilitates the transition to more surface-driven convection. The coassociation between boundary layer depth and precipitation does not provide definitive conclusions on the isolated effect of precipitation on the pace of the transition. Differences between the initial conditions of the three examples provide opportunities for further modeling studies.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1979

The effect of fuel sprays on emissions from a gas turbine combustor

A research gas turbine combustor which allows for independent control of drop size, fuel/air ratio, air inlet temperature, pressure, reference velocity, and residence time has been used to study the influence of fuel spray characteristics on primary zone emissions. Local concentrations of oxides of nitrogen, carbon monoxide and unburned hydrocarbons at various locations in the flow, local gas temperature, gas velocity, and the turbulence intensity (measured with laser velocimetry) are obtained. A comprehensive data analysis program to compute the local fuel/air ratio and the sum of the mole fractions of the species present confirms the validity of the emissions data. Increasing drop size is correlated with an increase in unburned hydrocarbons, while increasing residence time is associated with sharp decreases in hydrocarbons and carbon monoxide and an increase in oxides of nitrogen.

Nicholls, J. A.↗
NASA NTRSDate not supplied

SLD Instrumentation in Icing Wind Tunnels – Investigation Overview

A collaborative effort to better understand cloud characterization probes in Supercooled Large Drop (SLD) conditions, as well the ability to simulate these conditions in several icing wind tunnels, was undertaken by NASA, NRCC, CIRA, ECCC, FAA and Met Analytics, Inc. Both drop sizing and liquid water content, LWC, were measured with various probes using current to emerging technologies. To ensure the best possible data quality from the newest probes, the probe manufacturers, SEA, Inc. and Artium, Inc. were invited to support testing and data analysis efforts. A common set of probes was identified to test in each of the three participating facilities: NRCC’s Altitude Icing Wind Tunnel, NASA’s Icing Research Tunnel and CIRA’s Icing Wind Tunnel. From the common set of probes, a subset were identified to use for comparison across the three facilities. These were the CDP-2 and 2D-S for drop sizing, and the Multi-wire for LWC. The LWC value was also checked by measuring the ice accretion thickness under hard rime conditions on a NACA-0012 airfoil. A common test matrix with sweeps in both LWC and median volume diameter, MVD, was developed. Each facility achieved these conditions as determined by their own calibration. The MVD ranged from 20 to at least 200 um, and LWC ranged from 0.5 to 3 g/m3. The comparison probes tested at common conditions in each facility were intended to allow for a direct comparison, and check of potential facility bias.

Icing Wind Tunnel↗
NASA NTRS1993

Experimental studies on effervescent atomizers with wide spray angles

An experimental investigation was conducted to examine the operating and spray characteristics of two internal-mixing twin-fluid atomizers that were designed to produce effervescent atomization at low air/liquid mass ratios (ALR's). These two experimental atomizers ejected the two phase flow so as to produce a wide spray angle. One atomizer was a plain orifice design that used a four-hole exit orifice which divided and turned the two phase flow just prior to ejection. The other atomizer, called the conical sheet atomizer, ejected the two phase flow through an annular passage in such a way as to form a hollow cone spray. The atomizer operating parameters varied during this investigation were the air/liquid mass ratio, atomizer operating pressure, and, in the case of the conical sheet atomizer, the exit gap width. Studies of spray characteristics included measurements of the spray Sauter mean diameter (SMD), drop size distribution, and, for the conical sheet atomizer, circumferential distribution of the liquid mass within the spray. For both atomizers it was found that SMD decreases with an increase in either ALR or operating pressure. The effect of ALR on SMD diminishes as the value of ALR increases. For the conical sheet atomizer, when operating at low values of pressure and ALR, SMD increases with increase in gap width, but the influence of gap width on SMD diminishes with an increase in either pressure or ALR. At the highest operating pressure of the conical sheet atomizer (552 kPa), SMD is independent of gap width at all ALR's. For both atomizers, changes in operating pressure and ALR have little effect on the distribution of drop sizes in the spray.

Whitlow, J. D.↗
DOE OSTI2020

Optimal Estimation Retrievals and Their Uncertainties: What Every Atmospheric Scientist Should Know

Remote sensing instruments are heavily used to provide observations for both the operational and research communities. These sensors do not provide direct observations of the desired atmospheric variables, but instead, retrieval algorithms are necessary to convert the indirect observations into the variable of interest. It is critical to be aware of the underlying assumptions made by many retrieval algorithms, including that the retrieval problem is often ill posed and that there are various sources of uncertainty that need to be treated properly. In short, the retrieval challenge is to invert a set of noisy observations to obtain estimates of atmospheric quantities. The problem is often complicated by imperfect forward models, by imperfect prior knowledge, and by the existence of nonunique solutions. Optimal estimation (OE) is a widely used physical retrieval method that combines measurements, prior information, and the corresponding uncertainties based on Bayes’s theorem to find an optimal solution for the atmospheric state. Furthermore, OE also allows the relative contributions of the different sources of error to the uncertainty in the final retrieved atmospheric state to be understood. Here, we provide a novel Python library to illustrate the use of OE for inverse problems in the atmospheric sciences. We introduce two example problems: how to retrieve drop size distribution parameters from radar observations and how to retrieve the temperature profile from ground-based microwave sensors. Using these examples, we discuss common pitfalls, how the various error sources impact the retrieval, and how the quality of the retrieval results can be quantified.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1994

Structure of a Swirl-stabilized, Combusting Spray

Measurements of the structure of a swirl-stabilized, reacting spray are presented. The configuration consisted of a research air-assist atomizer located in the center surrounded by a coflowing air stream. Both the air assist and coflow streams had swirl imparted to them in the same direction with 45 degree angle swirlers. The fuel and air entered the combustor at ambient temperature and the combustor was operated in an unconfined environment. The gas phase was seeded with aluminum oxide particles in order to obtain velocity measurements. Velocity measurements for the gas phase are reported for both an isothermal, single-phase case without drops and a reacting spray case at axial distances from 2.5 to 350 mm downstream of the nozzle. Both mean and fluctuating values are reported. Heptane fuel was used for all the experiments. Drop size and velocity, and drop number flux are also reported for five axial distances downstream. Both mean and fluctuating values are reported for the drops. The measurements were performed using a two-component phase/Doppler particle analyzer. Profiles across the entire flowfield where velocities were significant are presented. Mean gas phase temperatures were also measured intrusively using a single pt/pt-13 percent rh thermocouple and are reported at axial distances from 2.5 to 200 mm downstream of the nozzle.

Bulzan, Daniel L.↗
NASA NTRS1974

Two phase detonation studies

An experimental study of the passage of a shock wave over a burning fuel drop is described. This includes high speed framing photographs of the interaction taken at 500,000 frames per second. A theoretical prediction of the ignition of a fuel drop by a shock wave is presented and the results compared with earlier experimental work. Experimental attempts to generate a detonation in a liquid fuel drop (kerosene)-liquid oxidizer drop (hydrogen peroxide)-inert gas-environment are described. An appendix is included which gives the analytical prediction of power requirements for the drop generator to produce certain size drops at a certain mass rate. A bibliography is also included which lists all of the publications resulting from this research grant.

Nicholls, J. A.↗
NASA NTRS1995

Structure of a swirl-stabilized combusting spray

Measurements of the structure of a swirl-stabilized, reacting spray are presented. The configuration consisted of a research air-assist atomizer located in the center surrounded by a co-flowing airstream. Both the air-assist and co-flowing streams had swirl imparted to them in the same direction with 45-deg angle swirlers. The fuel and air entered the combustor at ambient temperature and the combustor was operated in an unconfined environment. The gas phase was seeded with aluminum-oxide particles in order to obtain velocity measurements. Mean velocity measurements for the gas phase are reported for both an isothermal, single-phase case without drops and a reacting spray case at axial distances from 2.5 to 50 mm downstream of the nozzle. Heptane fuel was used for all the experiments. Drop size and mean velocity and drop number flux are also reported for five axial distances downstream. The measurements were performed using a two-component phase/Doppler particle analyzer. Profiles across the entire flowfield where velocities were significant are presented. Mean gas-phase temperatures were also measured intrusively using a single pt/pt-13%rh thermocouple and are also reported at axial distances from 2.5 to 50 "im downstream of the nozzle.

Bulzan, Daniel L.↗
DOE OSTI2022

Evolution of Droplet Size Distributions During the Transition of an Ultraclean Stratocumulus Cloud System to Open Cell Structure: An LES Investigation Using Lagrangian Microphysics

Here, a state-of-the-art Lagrangian microphysics scheme is used in a large-eddy simulation to investigate the stratocumulus transition from closed to open cell structure. Processes controlling precipitation development, which is a key to the transition, are analyzed by leveraging unique benefits of Lagrangian microphysics, particularly the ability to track computational drops in the flow. Sufficient time is needed for coalescence growth of cloud drops to drizzle within the updraft-downdraft cycle of large eddies. This favors broad drop size distributions (DSDs) and drizzle growth in downdrafts, where drops are typically much older than in updrafts. During the closed cell stage, mean cloud drop radius is too small, and the DSDs are too narrow, so that the timescale for coalescence is much longer than the large eddy turnover time and drizzle growth is limited. The closed-to-open cell transition occurs when these timescales become comparable and the precipitation flux increases sharply.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1983

Ultrasonics and Optics Would Control Shot Size

Feedback system assures production of silicon shot of uniform size. Breakup of silicon stream into drops is controlled, in part, by varying frequency of vibrations imparted to stream by ultrasonic transducer. Drop size monitored by photodetector. Control method particularly advantageous in that constant size is maintained even while other process variables are changed deliberately or inadvertently. Applicable to materials other than silicon.

Morrison, A. D.↗
NASA NTRS1994

Phase segregation due to simultaneous migration and coalescence

Ground-based modeling and experiments have been performed on the interaction and coalescence of drops leading to macroscopic phase separation. The focus has been on gravity-induced motion, with research also initiated on thermocapillary motion of drops. The drop size distribution initially shifts toward larger drops with time due to coalescence, and then a back towards smaller drops due to the larger preferentially settling out. As a consequence, the phase separation rate initially increases with time and then decreases.

Davis, Robert H.↗
NASA NTRS1977

Comparison of two different raindrop disdrometers

Different types of impact sensors, used for the measurement of drop size distribution, are described and compared. All of them generate an electrical output which is to a first order a function of the velocity and mass of impacting drops within the size range of 0.25 to 5.0 mm. The disdrometers discussed include an active styrofoam disdrometer, a passive plexiglass sensor, and a cast epoxy disdrometer sensor. The sensors are calibrated by dropping water drops of known size on the sensor, and using an oscilloscope to measure peak amplitude. Similar response characteristics are observed for the active styrofoam disdrometer and the passive plexiglass and brass sensors. The cast epoxy impact sensor is noted to have a faster response and to be more sturdy than the styrofoam or plexiglass sensors.

Rowland, J. R.↗