Search NASA⌕ Search

SEARCH · Search NASA

Results for “edge state”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Recycling isotachophoresis - A novel approach to preparative protein fractionation

The concept of automated recycling isotachophoresis (RITP) as a purification methodology is discussed, in addition to a description of the apparatus. In the present automated RITP, the computer system follows the achievement of steady state using arrays of universal and specific sensors, monitors the position of the front edge of the zone structure, activates the counterflow if the leading boundary passes a specified position along the separation axis, or changes the applied current, accordingly. The system demonstrates high resolution, in addition to higher processing rates than are possible in zone electrophoresis or isoelectric focusing.

Sloan, Jeffrey E.↗
NASA NTRS1991

Effects of steady state adiabatic convection on the configuration of the near-earth plasma sheet. II

Convection in the plasma sheet is studied using two new two-dimensional, force-balanced magnetospheres that satisfy pV exp 5/3 = constant in the inner and middle plasma sheet. It is confirmed that there exists a substantial set of steady state adiabatic solutions. Like a previously obtained steady state solution, each of these models exhibit a broad minimum in equatorial magnetic field strength B(ze) tailward of the inner edge region between 10 and 20 R(E), but they possess higher values of flux tube content pV exp 5/3 and thus have more stretched tidal configurations and smaller minimum values of B(ze) than those in the original model. A steady state magnetic field model in which B(ze)/B(lobe) at 36 R(E) geocentric distance is close to the observed value has been constructed. The results indicate that the B(ze) minimum tends to form within the Alfven layers. The broader the Alfven layers, the less pronounced the minimum.

Hau, Lin-Ni↗
NASA NTRS1993

Applications of x ray absorption fine structure to the in situ study of the effect of cobalt in nickel hydrous oxide electrodes for fuel cells and rechargeable batteries

Electronic and structural aspects of composite nickel-cobalt hydrous oxides have been examined in alkaline solutions using in situ X-ray absorption fine structure (XAFS). The results obtained have indicated that cobalt in this material is present as cobaltic ions regardless of the oxidation state of nickel in the lattice. Furthermore, careful analysis of the Co K-edge Extended X-ray absorption fine structure data reveals that the co-electrodeposition procedure generates a single phase, mixed metal hydrous oxide, in which cobaltic ions occupy nickel sites in the NiO2 sheet-like layers and not two intermixed phases each consisting of a single metal hydrous oxide.

Kim, Sunghyun↗
NASA NTRS2017

Scientific Investigations Associated with the Human Exploration of Mars in the Next 35 Years

A human mission to Mars would present an unprecedented opportunity to investigate the earliest history of the solar system. This history that has largely been overwritten on Earth by active geological processing throughout its history, but on Mars, large swaths of the ancient crust remain exposed at the surface, allowing us to investigate martian processes at the earliest time periods when life first appeared on the Earth. Mars' surface has been largely frozen in place for 4 billion years, and after losing its atmosphere and magnetic field what re-mains is an ancient landscape of former hydrothermal systems, river beds, volcanic eruptions, and impact craters. This allows us to investigate scientific questions ranging from the nature of the impact history of the solar system to the origins of life. We present here a summary of the findings of the Human Science Objectives Science Analysis Group, or HSO-SAG chartered by MEPAG in 2015 to address science objectives and landing site criteria for future human missions to Mars (Niles, Beaty et al. 2015). Currently, NASA's plan to land astronauts on Mars in the mid 2030's would allow for robust human exploration of the surface in the next 35 years. We expect that crews would be able to traverse to sites up to 100 km away from the original landing site using robust rovers. A habitat outfitted with state of the art laboratory facilities that could enable the astronauts to perform cutting edge science on the surface of Mars. Robotic/human partnership during exploration would further enhance the science return of the mission.

Niles, P. B.↗
NASA NTRSDate not supplied

Cross-Government Development of Space-Based Quantum Sensors for Earth and Space Science

Quantum sensing technologies promise advantages over their traditional counterparts in terms of sensitivity and accuracy, including higher signal-to-noise ratios, better measurement resolution and sensitivity, and accuracies that can be tied to fundamental constants. As a result of the potentially promising advantages of quantum sensing technologies, the multi-agency Space Science and Technology Partnership Forum (S&T Forum), consisting of NASA, NRO, and USSF, conducted a 2023 study to identify the current state of space-based quantum sensing technology development that will enable cutting-edge Earth and space science. The findings contained within this work provide insight into quantum sensing and quantum enabling technology work across the S&T Forum to inform technology development and identify potential government, industry, and academic coordination and collaboration opportunities in quantum sensing within the Earth and space science community. The results herein focus on the collation of quantum sensing technologies, facilities, and developers captured from the participants of the study to provide a broad overview of quantum sensor development for the Earth and space science community; specifically highlighting how five particular areas of quantum sensing technology (listed in alphabetical order) are of near-term interest to all three S&T Forum agencies: atomic clocks, atom interferometers, quantum magnetometers, Rydberg sensors, and single photon detectors. The findings in this work point to the intent of the S&T Forum agencies to lean into the development of quantum sensing technology in which the three agencies have mutual near-term interest, including cross-cutting enabling component technologies. The information presented provides points of entry in terms of people, facilities, and quantum sensing technology work within the government as well as increased transparency into the five quantum sensing technology areas of mutual interest of the S&T Forum agencies to remove barriers and encourage participation and partnership with the Earth and space science community.

Quantum↗
NASA NTRS1988

Electro-impulse de-icing electrodynamic solution by discrete elements

This paper describes a technique for analyzing the electrodynamic phenomena associated with electro-impulse deicing. The analysis is done in the time domain and utilizes a discrete element formulation concept expressed in state variable form. Calculated results include coil current, eddy currents in the target (aircraft leading edge skin), pressure distribution on the target, and total force and impulse on the target. Typical results are presented and described. Some comparisons are made between calculated and experimental results, and also between calculated values from other theoretical approaches. Application to the problem of a nonrigid target is treated briefly.

Bernhart, W. D.↗
NASA NTRS1992

BBXRT and Ginga observations of the Seyfert 1 galaxy MRK 335

We present new X-ray observations of Mrk 335 in the 0.4-10 keV band using the broadband X-ray telescope (BBXRT) and in the 2-18 keV band with Ginga. The BBXRT data show a gradual steepening of the spectrum to softer energies. We suggest that the nuclear emission can be explained by a self-consistent pair cascade model. The Ginga data show evidence for variability in absorption, uncorrected with flux changes of the continuum source. The inconsistency between the opacity observed at the iron K edge and at softer X-ray energies implies that the absorber has an ionization state BeXV.

Turner, T. J.↗
NASA NTRS1993

BBXRT and Ginga observations of the Seyfert 1 galaxy Markarian 335

We present new X-ray observations of Mrk 335 in the 0.4-10 keV band using BBXRT and in the 2-20 keV band with Ginga. The BBXRT data show a break to a softer spectrum below about 1 keV. The Ginga data show evidence for variability in absorption, uncorrelated with flux changes of the continuum source. The inconsistency between the opacity observed at the iron K edge and at softer X-ray energies implies that the absorber has an ionization state about FeXV. We suggest that the nuclear emission can be explained by a self-consistent pair cascade model as developed by Zdziarski et al. (1990) and Zdziarski and Coppi (1991), where the compactness parameter inferred from the spectral fits to both data sets is in good agreement with the value calculated from the ratio of observed X-ray luminosity and variability time scale.

Turner, T. J.↗
NASA NTRS2002

Ti-48Al-2Cr-2Nb Evaluated Under Fretting Conditions

Material parameters govern many of the design decisions in any engineering task. When two materials are in contact and microscopically small, relative motions (either vibratory or creeping) occur, and fretting fatigue can result. Fretting fatigue is a material response influenced by the materials in contact as well as by such variables as loading and vibratory conditions. Fretting produces fresh, clean interacting surfaces and induces adhesion, galling, and wear in the contact zone. Time, money, and materials are unnecessarily wasted when galling and wear result in excessive fretting fatigue that leads to poorly performing, unreliable mechanical systems. Fretting fatigue is a complex problem of significant interest to aircraft engine manufacturers. It can occur in a variety of engine components. Numerous approaches, depending on the component and the operating conditions, have been taken to address the fretting problems. The components of interest in this investigation were the low-pressure turbine blades and disks. The blades in this case were titanium aluminide, Ti-48Al-2Cr- 2Nb, and the disk was a nickel-base superalloy, Inconel 718 (IN 718). A concern for these airfoils is the fretting in fitted interfaces at the dovetail where the blade and disk are connected. Careful design can reduce fretting in most cases, but not completely eliminate it, because the airfoils frequently have a skewed (angled) blade-disk dovetail attachment, which leads to a complex stress state. Furthermore, the local stress state becomes more complex when the influence of the metal-metal contact and the edge of contact are considered.

Miyoshi, Kazuhisa↗
NASA NTRS1995

X-Ray Photoemission Measurements and Electronic Structure of HgBa2CaCu2O6+Delta

X-ray photoelectron spectroscopy data presented here are the first on an epitaxial thin film of a mercury cuprate superconductor, the first in which signals from the superconducting phase dominate all the core level spectra, and the first to exhibit a clear Fermi edge in the valence band region. Mercury is found to be in a single chemical state, contrary to reports based on sintered polycrystalline pellets.

x-ray photoemission photoelectron spectroscopy mer↗
NASA NTRS2004

Jet Propulsion Laboratory: Annual Report 2003

If you stepped outdoors on the final evening of 2003 and looked up into the night sky, many celestial events were taking place. A hundred million miles away from Earth, a dust storm swirled across the terracotta peaks and gullies of Mars, as two six-wheeled robots bore down on the planet. They were soon to join two orbital sentries already stationed there. A few hops across the inner solar system, another spacecraft was closing in on a ball of ice and rock spewing forth a hailstorm of dust grains, heated as it swung in toward the Sun. Closer in, two newly lofted space telescopes scanned the skies, their mirrors gathering photons that had crossed the empty vastness of space for billions of years, recording ancient events in unimaginably distant galaxies. And streaking overhead every few minutes directly above our home planet, a handful of satellites was recording the unfolding events of a tropical cyclone off the east coast of Africa and a blizzard that carpeted the northwestern United States. As 2003 drew to a close, the Jet Propulsion Laboratory was on the cusp of an extraordinarily busy period, a time when JPL will execute more fly-bys, landings, sample returns and other milestones than at any other time in its history. The exploration we undertake is important for its own sake. And it serves other purposes, none more important than inspiring the next generation of explorers. If the United States wishes to retain its status as a world leader, it must maintain the technological edge of its workforce. What we do here is the stuff of dreams that will inspire a new generation to continue the American legacy of exploration.

Jet Propulsion Laboratory (JPL)↗
NASA NTRS1989

Temporal features of the outflow of heavy ionospheric ions in response to a high altitude plasma cavity

Using a hydrodynamic model for the plasma, it is demonstrated that the auroral plasma cavity is capable of drawing an appreciably large flux of oxygen ions, which are normally gravitationally bound. This escape mechanism of O(+) does not involve any additional heating or acceleration of the plasma in the ionosphere. The temporal evolution of the outflow shows that it starts near the cavity and penetrates into the ionosphere with a flux front moving down with the ion-acoustic speed. A steady outflow is reached in a few hours for a cavity at a height of one R(e) if the cavity is maintained. This time reduces to less than 1 hour for cavity heights less than 3000 km. During the transient state the outflux can appreciably exceed that in the steady state. In view of the horizontal convection, the transient outflow is of special significance. As the cavity descends, the ionospheric flux of O(+) increases; for the lower edge of the cavity in the altitude range 3000-10,000 km, the steady flux is found to be in the range 10 to the 7th to 10 to the 9th. An analysis for the steady state shows that outflow is controlled by the density scale height in the cavity.

Singh, Nagendra↗
NASA NTRS2011

Model-Based Wavefront Control for CCAT

The 25-m aperture CCAT submillimeter-wave telescope will have a primary mirror that is divided into 162 individual segments, each of which is provided with 3 positioning actuators. CCAT will be equipped with innovative Imaging Displacement Sensors (IDS) inexpensive optical edge sensors capable of accurately measuring all segment relative motions. These measurements are used in a Kalman-filter-based Optical State Estimator to estimate wavefront errors, permitting use of a minimum-wavefront controller without direct wavefront measurement. This controller corrects the optical impact of errors in 6 degrees of freedom per segment, including lateral translations of the segments, using only the 3 actuated degrees of freedom per segment. The global motions of the Primary and Secondary Mirrors are not measured by the edge sensors. These are controlled using a gravity-sag look-up table. Predicted performance is illustrated by simulated response to errors such as gravity sag.

edge sensor↗
NASA NTRS2026

Aerodynamic Performance and Acoustic Impacts of Varying Tip Speeds and Tripping Conditions on Small Rotors in an Anechoic Hover Chamber

Performance and acoustic measurements were taken in a hover chamber for various optimum hovering rotors (OPT2) and a commercial-off-the-shelf (COTS) rotor. A total of 10 rotors are included in this report, all of which have two blades and a tip radius of 0.1905 m (7.5 in.). For the OPT2, results for three additive manufacturing methods of fabrication are presented: stereolithography(SLA) using Accura Xtreme, SLA using FormLabs 10K resin, and selective laser sintering (SLS) using mineral-filled PA12 nylon material. All but one set of rotors were designed with a trailing edge bluntness that is 3% of the chord length, and one set was designed with a bluntness that is 1% of the chord length. Spanwise boundary layer trips were applied to the SLA, FormLabs and COTS rotors. Performance comparisons between untripped and tripped configurations demonstrate the impact of boundary layer state on rotor efficiency. Acoustic results, including periodic and broadband noise components, are presented. The effects of tripping these rotors near the leading edge are also presented. For some of the rotors, acoustic spectra of tip speed sweeps are presented to show how the frequency content changes with tip speed. Amplitude and frequency scaling methods are used to collapse broadband spectra at various tip speeds towards a unified curve. These findings contribute to the understanding of small rotor aeroacoustics and provide valuable datasets for computational model validation in urban air mobility applications.

eVTOL↗
NASA NTRS1973

Pitting of titanium. I - Titanium-foil experiments. II - One-dimensional pit experiments.

Pitting experiments were conducted with strips of titanium foil in beakers containing chloride, bromide, or iodide solutions. The potentials were determined in reference to the saturated calomel electrode. Corrosion occurred at the edge of a foil specimen when it was maintained at a potential between the steady-state pitting potential of about 0.9 V and a potential of about 1.4 V in neutral bromide solution. A model is discussed to account for the complex relationships observed in the experiments. Conclusions based on experiments conducted with one-dimensional pits at the ends of insulated titanium pencils in the anode-facing-up position are also presented.

Beck, T. R.↗
NASA NTRS1981

Infrared sources in dense molecular clouds

Recent accomplishments in the infrared study of dense molecular clouds are reviewed, and the outstanding problems in the area are discussed. Such questions as whether clouds are collapsing, how they can be classified, and whether star formation is occurring on the edges of clouds are analyzed. Problems of determining size, energy distribution and luminosity, spectral features, evolutionary state, and energetics of infrared sources are discussed.

Evans, N. J., II↗
NASA NTRS1984

In Situ Composite Fastener

Fasteners installed prior to curing. In situ composite fastener polymeric, graphite, glass, or metallic thread, pin, or staple. Selected fastener pressed through thickness of composite component while composite is in prepreg or B-stage state. Parts not removed from mold to install fastener. Technique used around cutouts to prevent free edges from delaminating.

Freeman, W. T., Jr.↗