Search NASA⌕ Search

SEARCH · Search NASA

Results for “evaporative cooling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

209 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Analysis of Electro-static Assisted Air Dehumidification

The removal of water vapor from the air to reduce relative humidity is a well-known indoor environmental comfort requirement. Common dehumidification approaches require a substantial amount of energy and usually involve the cooling of atmospheric humid air below its dew point or the use of absorbent/adsorbent materials to extract water vapor out of the air. More recently, researchers investigated the effect of electrostatic forces for enhancing water vapor condensation. However, the studies are limited, and there is a lack of correlations that can predict the dehumidification rate. Also, the findings from the literature focused mainly on small flow rates on the order of one to two cfm. Electrically-enhanced condensation consists of the use of highly charged particles, preferably highly charged water droplets, that attract polar water vapor molecules to their surfaces and promote condensation, a phenomenon known as dielectrophoresis. An effect of the electric charge is the reduction of the vapor pressure on the droplets' surface with respect to the saturated pressure predicted by the Kelvin equation. Consequently, the equilibrium between evaporation and condensation is shifted towards condensation. Following the application of the modified Kelvin-Thomson theory, we developed a preliminary physics-based model to predict an effective size range of the charged droplets for optimal dehumidification. The range resulted in about 2 to 4 μm in diameter, under few simplifying assumptions. The effect of the size and the charge of the electrosprayed droplets on the overall dehumidification rate was briefly discussed. The use of electrosprays to produce small but highly charged droplets was broadly discussed in this paper. The cone-jet mode was identified as the most suitable electrospray operational mode, and it generated droplets of small size and high electrical charge. The cone-jet stability was also analyzed in detail. The preliminary data of the present work and the model results indicated that several electrospray heads were required to achieve a 5% dehumidification rate for airflow rates of about 5 cfm.

Morcelli, Stefano↗
DOE OSTI2021

Analysis of New Data of Electro-static Assisted Air Dehumidification Processes

The removal of water vapor from the air to reduce relative humidity is a well-known indoor environmental comfort requirement. Common dehumidification approaches require a substantial amount of energy and usually involve the cooling of atmospheric humid air below its dew point or the use of absorbent/adsorbent materials to extract water vapor out of the air. More recently, researchers investigated the effect of electrostatic forces for enhancing water vapor condensation. However, the studies are limited, and there is a lack of correlations that can predict the dehumidification rate. Also, the findings from the literature focused mainly on small flow rates on the order of one to two cfm. Electrically-enhanced condensation consists of the use of highly charged particles, preferably highly charged water droplets, that attract polar water vapor molecules to their surfaces and promote condensation, a phenomenon known as dielectrophoresis. An effect of the electric charge is the reduction of the vapor pressure on the droplets' surface with respect to the saturated pressure predicted by the Kelvin equation. Consequently, the equilibrium between evaporation and condensation is shifted towards condensation. Following the application of the modified Kelvin-Thomson theory, we developed a preliminary physics-based model to predict an effective size range of the charged droplets for optimal dehumidification. The range resulted in about 2 to 4 m in diameter, under few simplifying assumptions. The effect of the size and the charge of the electrosprayed droplets on the overall dehumidification rate was briefly discussed. The use of electrosprays to produce small but highly charged droplets was broadly discussed in this paper. The cone-jet mode was identified as the most suitable electrospray operational mode, and it generated droplets of small size and high electrical charge. The cone-jet stability was also analyzed in detail. The preliminary data of the present work and the model results indicated that several electrospray heads were required to achieve a 5% dehumidification rate for airflow rates of about 5 cfm.

Morcelli, Stefano↗
DOE OSTI2021

Boron nitride nanotube precursor formation during high-temperature synthesis: kinetic and thermodynamic modelling

In this work, we performed integrated modelling of the chemical pathways of formation for boron nitride nanotube (BNNT) precursors during high-temperature synthesis in a B/N 2 mixture. Integrated modelling includes quantum chemistry, Quantum–classical molecular dynamics, thermodynamic modelling, and kinetic approaches. We demonstrate that BN compounds are formed via the interaction of molecular nitrogen with small boron clusters, rather than through interactions with less reactive liquid boron. (This process can also be described as N 2 molecule fixation.) Liquid boron evaporates to produce these boron clusters (B m with m ≤ 5), which are subsequently converted into B m N n chains. The production of such chains is crucial to the growth of BNNTs because these chains form the building blocks of bigger and longer BN chains and rings, which are in turn the building blocks of fullborenes and BNNTs. Additionally, kinetic modelling revealed that B 4 N 4 and B 5 N 4 species in particular play a major role in the N 2 molecule fixation process. Furthermore, the formation of these species via reactions with B 4 and B 5 clusters is not adequately described under the assumption of thermodynamic equilibrium, as is demonstrated in our kinetic modelling. Thus, the accumulation of both B 4 N 4 and B 5 N 4 depends on the background gas pressure and the gas cooling rate. Long BN chains and rings, which are precursors of the fullborene and BNNT growth, form via self-assembly of components B 4 N 4 and B 5 N 4 . Our modelling results—particularly the increased densities of B 4 N 4 and B 5 N 4 species at higher gas pressures—explain the experimentally observed effect of gas pressure on the yield of high-quality BNNTs. The catalytic role of hydrogen was also studied; it is shown that HBNH molecules can be the main precursor of BNNT synthesis in the presence of hydrogen.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Developments on two lithium vapor-box linear test-stand experiments

The lithium vapor-box divertor is a possible fusion power exhaust solution.It uses condensation pumping to create a gradient of vapor density in a divertor slot; this should allow a stable detachment front without active feedback.As initial explorations of the concept, two test stands which take the form of three connected cylindrical stainless steel boxes are being developed: one without plasma at PPPL, to test models of lithium evaporation and flow; and one for the linear plasma device Magnum-PSI (at DIFFER in Eindhoven, The Netherlands) to test the ability of a lithium vapor cloud to induce volumetric detachment and redistribute the plasma power.The first experiment uses boxes with diameters of 6 cm, joined by apertures with diameters of 2.2 cm. Up to 1 g of Li is placed in one box, which is heated to up to 600 degrees C. The Li evaporates, then flows to and condenses in the two other, cooler boxes over several minutes. The quantity of Li transported is assessed by weighing the boxes before and after the heating cycle, and is compared to the quantity predicted to flow for the box at its measured temperature using a Direct Simulation Monte Carlo code, SPARTA. With good experimental conditions, the two values agree to within 15%.The experiment on Magnum-PSI is in the conceptual design stage.The design is assessed by simulations using the code B2.5-Eunomia.They show that when the hydrogen-ion plasma beam, with n_e = 4e20 per cubic meter, T_e = 1.5 eV, and r = 1 cm, is passed through a 16 cm long, 12 Pa, 625 degree C Li vapor cloud, the plasma heat flux and pressure on the target are significantly reduced compared to the case without Li.With the Li present, the plasma is cooled by excitation of Li neutrals followed by radiation until it volumetrically recombines, lowering the heat flux from 3.7 MW/m^2 to 0.13 MW/m^2, and the pressure is reduced by 93%, largely by collisions of hydrogen ions with neutral Li.

divertor↗
DOE OSTI2021

Synthesis and characterization of amorphous Fe2.75Dy-oxide thin films demonstrating room-temperature semiconductor, magnetism, and optical transparency

Recently, amorphous/disordered oxide thin films made from Fe and lanthanides like Dy and Tb have been reported to have a rich set of magnetic, optical, and electronic properties, as well as room-temperature magneto-electric coupling with multiferroics [A. Malasi et al., Sci. Rep. 5, 18157 (2015); H. Taz et al., Sci. Rep. 6, 27869 (2016); and H. Taz et al., Sci. Rep. 10, 1–10 (2020)]. Here, we report the synthesis and detailed characterization of Fe2.75Dy-oxide thin films prepared on various substrates using electron beam co-evaporation. The structure, chemistry, electric, magnetic, and optical properties were studied for the as-prepared and annealed (373 K, in air, 1 h) films of thickness 40 nm. High resolution transmission electron microscopy and electron diffraction study showed that the films were amorphous in both the as-prepared and annealed states. The electron energy-loss spectroscopy studies quantified that metal oxygen stoichiometry changed from Fe2.75Dy-O1.5 to Fe2.75Dy-O1.7 upon annealing. Synchrotron-based x-ray absorption spectroscopy investigation confirmed that the as-prepared films were highly disordered with predominantly metallic Fe and Dy states that became slightly oxidized with annealing in air. The as-prepared amorphous films demonstrated significantly high value of ordinary (∼10 cm2/V s) and anomalous (∼102 cm2/V s) Hall mobility and high electrical conductivity of ∼103 S/cm at room temperature. The cryogenic magnetic property measurement shows two-step magnetization below 200 K, suggesting exchange-spring magnetic interaction. The nature of the field cooled and zero-field cooled curves suggested a spin-glass like transition between 78 K and 80 K, with a characteristic broad peak. The Tauc plot analysis from optical transmission spectra confirms the existence of an optical bandgap of ∼2.42 eV that increased slightly to ∼2.48 eV upon annealing. This rich set of transport, optical, and magnetic properties in these thin films is very exciting and points to potential applicability in low-cost multifunctional devices requiring a combination of transparent, semiconducting, and magnetic responses, such as in spintronics.

Prasad Koirala, Krishna (ORCID:000000029137917X)↗
DOE OSTI2023

Experimental performance of ejector heat pump operating in the sub-critical mode

Ejector heat pump (EHP) is an efficient-energy technology with a promising potential to replace the vapor compression cycle in heating and cooling applications. It can be powered by low-grade waste heat and uses environmentally friendly working fluids. EHP has also become a viable solution in research seeking cooling applications. However, little attention has been paid to using EHP for heating purposes. In order to investigate this, a steam EHP for domestic water heating was designed and built. The coefficient of performance (COP) is evaluated at various operating and design conditions in sub-critical operational modes to achieve higher condensation temperatures. Two primary nozzles with a throat diameter of 1.5 mm and 2.0 mm were investigated. The primary nozzle is movable along the ejector’s axis, allowing investigation of its positional effects on the EHP’s COP. Further, experimental measurements revealed that using a smaller throat diameter results in a high COP and low back pressure. The EHP COP and back pressure increase when the LTE temperature increases. Using a throat diameter of 1.5 mm, the EHP COP increases as the nozzle exit position (NXP) becomes closer to the constant area section. A COP of 2.42 and a back pressure of 4.28 kPa are achieved at a high-temperature evaporator (HTE) temperature of 130 °C and a low-temperature evaporator (LTE) temperature of 30 °C using a primary nozzle with 1.5 mm.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Rapid evolution of aerosol particles and their optical properties downwind of wildfires in the western US

Abstract. During the first phase of the Biomass Burn Operational Project (BBOP) field campaign, conducted in the Pacific Northwest, the DOE G-1 aircraft was used to follow the time evolution of wildfire smoke from near the point of emission to locations 2–3.5 h downwind. In nine flights we made repeated transects of wildfire plumes at varying downwind distances and could thereby follow the plume's time evolution. On average there was little change in dilution-normalized aerosol mass concentration as a function of downwind distance. This consistency hides a dynamic system in which primary aerosol particles are evaporating and secondary ones condensing. Organic aerosol is oxidized as a result. On all transects more than 90 % of aerosol is organic. In freshly emitted smoke aerosol, NH4+ is approximately equivalent to NO3. After 2 h of daytime aging, NH4+ increased and is approximately equivalent to the sum of Cl, SO42, and NO3. Particle size increased with downwind distance, causing particles to be more efficient scatters. Averaged over nine flights, mass scattering efficiency (MSE) increased in ∼ 2 h by 56 % and doubled in one flight. Mechanisms for redistributing mass from small to large particles are discussed. Coagulation is effective at moving aerosol from the Aitken to accumulation modes but yields only a minor increase in MSE. As absorption remained nearly constant with age, the time evolution of single scatter albedo was controlled by age-dependent scattering. Near-fire aerosol had a single scatter albedo (SSA) of 0.8–0.9. After 1 to 2 h of aging SSAs were typically 0.9 and greater. Assuming global-average surface and atmospheric conditions, the observed age dependence in SSA would change the direct radiative effect of a wildfire plume from near zero near the fire to a cooling effect downwind.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Downward jetting of a dynamic Leidenfrost drop

Jetting is a universal phenomenon frequently observed in nature and industries, for instance in rain drop impact, inkjet printing, spray cooling, fuel atomization, etc. In drop impact on a superheated surface, we observe the formation of a vapor cavity beneath the dynamic Leidenfrost drop and a consecutive downward ejection of a jet into the cavity, using ultrafast x-ray phase contrast imaging. We reveal that the cavity is induced mostly by the retraction of the drop and the jetting is caused by the convergence of capillary waves along the liquid-cavity interface. We find a jetting criterion based on the viscous damping of capillary waves: [OhWe 2 ] ≤ 66 ± 10. These results can provide important insight that leads to understanding and modeling of jets in nature.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

High-accuracy method for modeling nucleation and growth of particles

State-of-the-art numerical models describing the kinetics of aerosol particle nucleation and growth from a cooling vapor primarily use a nodal method, in which particles that are smaller than the critical size are omitted from consideration because they are thermodynamically unfavorable. This omission is based on the assumption that most newly formed particles are above the critical size, so that subcritical-size particles are not important to take into account. Due to the nature of the nodal method, it suffers from numerical diffusion, which can cause an artificial broadening of the cluster size distribution leading to a significant overestimation of the number of large-size particles. To address these issues, we propose a more accurate numerical method that explicitly models particles of all sizes, and uses a special numerical scheme that substantially reduces the numerical diffusion and provides high solution accuracy and numerical stability. We extensively compare this novel method to the commonly used nodal solver of the general dynamic equation (GDE) for particle growth and demonstrate that it offers GDE solutions with higher accuracy with low numerical diffusion. Incorporating small subcritical clusters into the solution is crucial for: 1) more precise determination of the entire particle size distribution function and 2) wider applicability of the model to experimental studies with non-monotonic temperature variations leading to particle evaporation. The computational code implementing this numerical method in Python is available upon request.

42 ENGINEERING↗
DOE OSTI2022

Experimental Investigation of the Effect of Atomizing Electrospray Nozzles on the Cooling and Reduced Humidification of Air

Separating sensible and latent cooling have shown the potential to reduce energy consumption in A/C systems for building HVAC applications. Several technologies exist based on vapor-compression refrigeration, enthalpy wheels, chemical adsorption and absorption materials, and mechanical cooling. However, their thermodynamics limits and high energy consumption hinder their deployment in hot and humid climatic regions. This paper focuses on separating sensible and latent cooling by using a new thermodynamics process and in-kind (i.e., non-vapor compression-based) technology. Highly electrically charged water droplets were sprayed in the airflow. These droplets attracted water vapor molecules to their surfaces and promoted condensation. The phenomenon was the result of simultaneous dielectrophoresis and electro-diffusion interactions. Studies in the literature have shown that using multiple capillary electrodes reduced air moisture by up to 5% when using nanometer-size droplets in the spray. Unfortunately, these studies were limited to low airflow rates, and the objective of this paper was to investigate how to scale up this in-kind approach to airflows typical of buildings. In the present paper, droplets of micrometer size were utilized to control the humidity for a 5-cfm flow rate. While this airflow was still low for building applications, it was 100 times fold the airflows in the literature studies. The air was tested at 20°C and at 50 and 80% relative humidity. A two-fluid atomizing nozzle produced the droplets in the spray, and high DC electric potential, up to 25 kV, was used to charge the fine droplets electrically. The air atomizing nozzle with high voltage potential resembled an evaporative cooler process. However, a measurable reduction of the absolute humidity of up to 2% was observed compared to the case of the nozzle with no high voltage potential. The entire device had one small nozzle selected from off-the-shelf components and had less than a 9 cm2 footprint area.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

n-Propylbenzene Droplet Combustion: Experiments and Numerical Modeling

n-Propylbenzene (PB, C9H12, 432K boiling point) is important as a constituent in surrogates for some transportation fuels but little is understood about its droplet burning characteristics. We present an experimental and numerical study of a fuel droplet burning under conditions where the sole means of gas transport is fuel evaporation at the droplet surface thereby creating a one-dimensional gas transport that is amenable to detailed numerical modeling. The one-dimensional gas transport that results is amenable to detailed numerical modeling. Initial droplet diameters (Do) ranged from 0.3 mm to about 5 mm to better understand the mechanisms that control burning over such a wide range of Do. For Do < 1 mm droplets were burned while anchored to 14 m SiC fibers within a sealed container in free-fall during which time the droplets were ignited by spark discharge and the burning process recorded by video cameras. Larger and free-floating droplets were studied in the spaced-based platform of the orbiting International Space Station for Do > 1.0 mm which provided unlimited times for experimental observation. Measurements of droplet, flame and soot shell diameters were made and are discussed in the presentation. The experimental results showed formation of optically thick soot clouds developing during burning that required a robust image analysis algorithm to enable measurement of droplet diameter. The measured droplet diameters were well predicted by a numerical model that included soot formation, a PB kinetic mechanism comprising 576 species and 27369 reactions, unsteady gas and liquid transport, variable properties and radiative transport. Flame diameters showed more variability compared to the simulations, depending on how the flame was defined (peak gas temperature and OH concentration). Droplets burned slower as Do was increased and the PB sooting propensity increased with Do. Flame extinction was observed for Do > 3.3 mm indicating a strong effect of radiation as Do was increased compared to the smaller droplet diameters examined where extinction was not experimentally observed. For the largest droplets examined the possibility that the observed extinction is indicative of a transition to cool flame burning is still under investigation.

Guo, Songtao↗