Results for “feedstock design” — Page 12

DOE OSTI2022

Design of an additively manufactured functionally graded material of 316 stainless steel and Ti-6Al-4V with Ni-20Cr, Cr, and V intermediate compositions

This study presents a method for designing a computationally informed gradient pathway to fabricate a functionally graded material (FGM) with terminal alloys of 316 stainless steel (SS316) and Ti-6Al-4V via directed energy deposition additive manufacturing with powder feedstock. In this work, the grading is accomplished through the introduction of intermediate elements and alloys (Ni-20Cr, Cr, and V) to avoid the brittle Fe-Ti intermetallic phases that form in the direct liquid phase joining of Ti-alloys and stainless steels. Using a combination of equilibrium calculations and Scheil-Gulliver simulations, a compositional pathway was designed to avoid deleterious phases. FGM samples were fabricated and experimentally characterized to determine the viability of the pathway. A change in phases from fcc to bcc was predicted to occur within the Ni-20Cr/Cr gradient region, and this was validated through experimental characterization. No detrimental phases (intermetallic, Laves, or σ phases) formed along the gradient path, demonstrating a successful computationally-informed design and fabrication of an FGM from SS316 to Ti-6Al-4V.

36 MATERIALS SCIENCE↗

DOE OSTI2019

Flow Characterization of Compressed Woody Biomass

Global interest for using terrestrial biomass as an energy source has been increasing recently due to potentially significant socio-economic and environmental benefits relative to fossil energy. Thermochemical biomass processes converting biomass to fuels are relatively well developed, e.g. for direct combustion, gasification, and pyrolysis. However, critical problems often arise when attempting to feed biomass into commercial-scale reactors continuously and without interruption. Biomass particles, whether derived from woody or agricultural feedstock, vary greatly in size, shape, density, and moisture content. High cohesiveness, low bulk density, and poor material flow characteristics often prevent continuous feeding due to bridging, rat-hole formation, blockage, and seal failures. Among all different types of feeders utilized to feed biomass into reactors, screw feeding has received significant attention in recent years. Screw feeders are fuel-specific and require careful design to be reliable, efficient, and economical, especially for reactors operating at elevated pressures. In order to mimic the flow properties of compressed biomass inside a compression-screw feeder, rheological properties of three types of compressed lignocellulosic biomass were investigated using a co-rotating twin screw microcompounder. Experiments were conducted to find the impact of moisture content, particle size and type, and screw speed on rheological properties of forest residual particles as well as sawdust. Increasing moisture from 10 to 50% reduced the apparent viscosity of the compressed biomass. Also, higher screw speeds (10 to 90 rpm) led to a lower relative viscosity. At elevated screw speeds, significant temperature differences were measured between the initial and final states, which should be accounted for in equipment design and operation.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2020

Communication of industry knowledge, best practices, and lessons learned in the space of cellulosic biofuels plant design, project development and execution and operations. Task 1 report

ExxonMobil Research and Engineering Company, via a technical services agreement, engages Idaho National Laboratory (INL) to provide general industry knowledge, best practices, and lessons learned in cellulosic ethanol plant design, project execution, and operations. INL will also assess publicly proposed cellulosic plant designs. The scope of work will be accomplished in three tasks: Task 1, Communicate industry knowledge; Task 2, Present high-level lessons learned; Task 3, Provide an engineering assessment of publicly proposed ethanol plant designs. This Task 1 report provides a high-level summary of general industry knowledge, best practice, and lessons learned in biomass feedstock logistics and integration with bioconversion processes.

09 BIOMASS FUELS↗

DOE OSTI2020

Development of a Genome-Scale Metabolic Model of Clostridium thermocellum and Its Applications for Integration of Multi-Omics Datasets and Computational Strain Design

Solving environmental and social challenges such as climate change requires a shift from our current non-renewable manufacturing model to a sustainable bioeconomy. To lower carbon emissions in the production of fuels and chemicals, plant biomass feedstocks can replace petroleum using microorganisms as biocatalysts. The anaerobic thermophile Clostridium thermocellum is a promising bacterium for bioconversion due to its capability to efficiently degrade lignocellulosic biomass. However, the complex metabolism of C. thermocellum is not fully understood, hindering metabolic engineering to achieve high titers, rates, and yields of targeted molecules. In this study, we developed an updated genome-scale metabolic model of C. thermocellum that accounts for recent metabolic findings, has improved prediction accuracy, and is standard-conformant to ensure easy reproducibility. We illustrated two applications of the developed model. We first formulated a multi-omics integration protocol and used it to understand redox metabolism and potential bottlenecks in biofuel (e.g., ethanol) production in C. thermocellum. Second, we used the metabolic model to design modular cells for efficient production of alcohols and esters with broad applications as flavors, fragrances, solvents, and fuels. The proposed designs not only feature intuitive push-and-pull metabolic engineering strategies, but also present novel manipulations around important central metabolic branch-points. We anticipate the developed genome-scale metabolic model will provide a useful tool for system analysis of C. thermocellum metabolism to fundamentally understand its physiology and guide metabolic engineering strategies to rapidly generate modular production strains for effective biosynthesis of biofuels and biochemicals from lignocellulosic biomass.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2026

Environmental Trade-Offs for a Process Utilizing Aerobic Respiration for Biological Conversion of Cellulosic Biomass-Derived Sugars to Hydrocarbons (Renewable Diesel Blendstock): Cooperative Research and Development Final Report, CRADA Number CRD-18-00765, Project 1

Phase II work is meant to develop an advanced understanding of how production of a renewable diesel blendstock from lignocellulosic biomass feedstocks via aerobic respiration at different production scales affects emissions of criteria pollutants and greenhouse gases (GHGs), local and regional air quality. The results could inform decisions by stakeholders (e.g., industry, community, air quality planners, investors) regarding relationships and tradeoffs between multiple environmental impacts and the challenges and opportunities for the design and deployment of a sustainable biofuel supply chain.

09 BIOMASS FUELS↗

DOE OSTI2025

Mechanical separations of corn stover anatomical fractions in an integrated feedstock preprocessing system: An experimental and data-driven modeling study

High variabilities of material attributes in lignocellulosic biomass present risks for biofuel and biochemical productions and must be mitigated via preprocessing. Since almost no mechanical device is originally designed for processing biomass, how to operate existing apparatuses with efficient performance has not been investigated extensively. This work presents a study on an integrated screening and air classification to separate cobs and stalks from husks and leaves in corn stover. Prototype machine learning models were developed to assess the feasibility of predicting the process outcome based on the measurable parameters. The models trained upon limited experimental data rendered decent predictive accuracy of yield and purity. The experimental data and modeling results collectively suggest decreasing throughput leads to a higher purity. To the contrary, if throughput increases, a lower purity is likely. A possible trade-off between yield and purity of the separated streams indicates the need for optimal combinations of feedstock size, moisture, and throughput to achieve optimized separations. The results of this study also suggest the need to further improve model predictability by developing more accurate formulations for physics governing the integrated unit operations. To accomplish this, additional experimental data needs to be generated for model training.

09 - BIOMASS FUELS↗

DOE OSTI2024

Deploying Purpose-Grown Energy Crops for Sustainable Aviation Fuel (Workshop Summary Report)

From June 6–7, 2023, the U.S. Department of Energy (DOE) Bioenergy Technologies Office (BETO) hosted the workshop “Deploying Purpose-Grown Energy Crops for Sustainable Aviation Fuel” in Kansas City, Missouri. The purpose of the workshop was to examine topics related to large-scale cultivation of purpose-grown energy crops—including algae—that can contribute feedstocks for the production of biofuels and bioproducts. This workshop was a means to gather a variety of stakeholders with the intent to identify elements for a potential future research strategy designed to overcome challenges and delve into the barriers related to the large-scale cultivation of purpose-grown crops. This document provides an overview and summary of the workshop’s presentations, breakout session discussions, and outcomes.

09 BIOMASS FUELS↗

DOE OSTI2023

Disruptive Supplies of Affordable Biomass Feedstock Grown in the Open Ocean

Marine BioEnergy was founded to commercialize a patented invention to enable open ocean kelp farms to produce feedstock by depth-cycling the farms. The concept is to surface the kelp during the day to absorb sunlight and CO 2 , and submerge the kelp at night to the nutrient-rich waters below the thermocline (~60-300 m deep). In an experiment, the kelp thrived in the depth-cycling environment. ARPA-E provided additional funds for Marine BioEnergy to develop a design of a full-scale farm system. Marine BioEnergy is preparing to deploy these farms, towed by unmanned drone submarines, to depth-cycle the kelp and produce disruptive supplies of affordable biomass feedstock that can be used to make carbon-neutral, drop-in fuels to enable the transition to net-zero carbon.

09 BIOMASS FUELS↗

DOE OSTI2022

Design of a Combined Proportional Integral Derivative Controller to Regulate the Temperature Inside a High-Temperature Tubular Solar Reactor

Solar fuels are proven to be promising candidates for thermochemical energy storage. However, the transient nature of solar radiation is an obstacle to maintaining a stable operational temperature inside a solar reactor. To overcome this challenge, the temperature of a solar reactor can be regulated by controlling the incoming solar radiation or the feedstock flowrate inside the reactor. In this work, a combined proportional integral derivative (PID) controller is implemented to regulate the temperature inside a high-temperature tubular solar reactor with counter-current flowing gas/particles. The control model incorporates two control systems to regulate incoming solar radiation and gas flow simultaneously. The design of the controller is based on a reduced-order numerical model of a high-temperature tubular solar reactor that is vertically oriented with an upward gas flow and downward particle flow. The reactor receives heat circumferentially through its wall over a finite segment of its length. Formulation of the heat transfer model is presented by applying the energy balance for the reactor tube and considering heat and mass transfer inside. A set of governing differential equations are solved numerically by using the finite volume method to obtain reactor wall, particles, and gas temperatures along the reactor length with various boundary conditions. Simulation results are used to tune the PID controller parameters by utilizing the Ziegler–Nichols tuning method. Both the simulation results and the controller performance are visualized on the LABVIEW platform. The controller is challenged to track different temperature setpoints with different scenarios of transient solar radiation. Here, the performance of the PID controller was compared to experimental results obtained from an industrial PID controller embedded in a 7 kW electric furnace. Results show that the combined PID controller is successful in maintaining a stable temperature inside the reactor by regulating the incoming solar radiation and the flowrate via small steady-state error and reasonable settling time and overshoot.

14 SOLAR ENERGY↗

DOE OSTI2023

Rheology of a Wet Waste Feedstock

The current study provides rheological characterization of a representative HTL feedstock, Wet Waste Feedstock # 22 (WW22), as a function of HTL-prototypic temperature and shear rates. Feed WW22 is derived from a regionally representative blend of food, waste water sludges, and FOG (fats, oils, and greases). Rheological characterization of WW22 as a function of temperature provides, in part, key information for development and economic assessment of HTL wet waste slurry handling and heating operations, which may facilitate improved design rigor and optimization of HTL unit operations.

09 BIOMASS FUELS↗

DOE OSTI2022

Impact of Nozzle Condition on Powder Catchment Efficiency for Coaxial Powder Direct Energy Deposition

Blown powder directed energy deposition is well-designed for fine resolution additive manufacturing processing. Coaxial powder deposition heads use an outer layer of shielding gas directed by an outer nozzle to prevent oxidation occurring during the powder melting process. Powder blown feedstock catchment efficiency can be as low as 50-80% whereas wire deposition systems are closer to 98% efficient. The present study evaluates the impact of directed energy deposition nozzle condition on catchment efficiency. Changes in the overall outer shielding gas nozzle length has been found to increase material usage efficiency by 10% through convergence of the powder flow. The results of this experiment show that for coaxial powder deposition head design, if the standoff distance can safely be decreased, powder catchment efficiency can be increased as the outer shielding gas nozzle is increased in length, or the standoff distance is decreased.

Heinrich, Lauren↗

DOE OSTI2022

Impact of Nozzle Condition on Powder Catchment Efficiency for Coaxial Powder Direct Energy Deposition

Blown powder directed energy deposition is well-designed for fine resolution additive manufacturing processing. Coaxial powder deposition heads use an outer layer of shielding gas directed by an outer nozzle to prevent oxidation occurring during the powder melting process. Powder blown feedstock catchment efficiency can be as low as 50-80% whereas wire deposition systems are closer to 98% efficient. The present study evaluates the impact of directed energy deposition nozzle condition on catchment efficiency. Changes in the overall outer shielding gas nozzle length has been found to increase material usage efficiency by 10% through convergence of the powder flow. The results of this experiment show that for coaxial powder deposition head design, if the standoff distance can safely be decreased, powder catchment efficiency can be increased as the outer shielding gas nozzle is increased in length, or the standoff distance is decreased.

Heinrich, Lauren↗

DOE OSTI2025

Optimization of overhang printing in ceramic binder jetting additive manufacturing

Cylindrical-shaped horizontally-hanging overhangs with different heights on a solid cubic body were printed via binder jetting additive manufacturing with sililcon carbide powder feedstock. Cracking on the overhang neck and sagging on the overhang body were observed both pre- and post-curing, especially on printed design with a smaller particle size of 10 μm. Here, it was found that the width of cracking and depth of sagging were dependent on the height relative to the solid body in the powder bed, and elevated position of overhang with large volume of underneath loose powder led to increased extend of cracking and sagging. Overhang diameter and weight were varied, which were found with no apparent effects on its deformation extend. To mitigate cracking and sagging, contactless support was designed and tested, which could significantly improve the overhang stability and avoid any overhang deformations. Support gap and support distance were studied for their effects on support capability. The printing processes with and without contactless support were simulated by a finite element modeling approach to understand the stress distribution and evolution of the overhang structures, which revealed stress concentrations on the upper neck point of the designed overhang.

Binder jetting↗

DOE OSTI2024

Additive manufacturing of LiCoO 2 electrodes via vat photopolymerization for lithium ion batteries

Additive manufacturing has the potential to revolutionize the fabrication of lithium-ion batteries for a diversity of applications including in portable, biomedical, aerospace, and the transportation fields. Standard commercial batteries consist of stacked layers of various components (current collectors, cathode, anode, separator and electrolyte) in a two-dimensional manner. By leveraging the latest advances in additive manufacturing and computer-aided design, an improved geometric and electrochemical configuration of these batteries can maximize energy efficiency while allowing design optimization to reduce dead space for a given application. In this work, a composite UV photosensitive resin was prepared and used as feedstock in a vat photopolymerization system. The resin was loaded with LiCoO 2 acting as electrochemically active material for the cathode of a lithium-ion battery, and was further improved with the addition of conductivity-enhancing carbonaceous additives. Challenges to additive manufacturing arise from the opacity and high viscosity of the composite nature of these electrochemically-active resins, which cause light refraction during selective UV curing. Subsequently, items were printed and subjected to a thermal post-processing step to obtain an adequate compromise between electrochemical performance and mechanical integrity. Both sintered and green state 3D printed cathodes were assembled into half-cell lithium-ion batteries using lithium metal as a reference and counter electrode. Electrochemical cycling of these batteries yielded satisfactory results approaching commercial LiCoO 2 cathodes’ performance, with the potential advantages of additive manufacturing – high surface area anode–cathode configurations for power performance as well as shape conformability.

25 ENERGY STORAGE↗

DOE OSTI2021

A Comparative Techno-Economic Analysis of Sustainable Methanol Synthesis Pathways from Biomass and CO2

The call to reduce global CO2 emissions is at the forefront of research and development in the transportation and petrochemical industries. A potential solution which intersects both sectors is the adoption and commercialization of more sustainable technologies for methanol production. Currently, methanol is gaining popularity as a possible fuel additive, and as a polymer precursor via established methanol-to-olefins routes which are increasing in capacity and utilization, putting methanol in the spotlight and global methanol production on the rise. At the same time, experimental and computational studies have surged, illuminating a wide array of novel process designs to introduce sustainable methanol into the market. However, with numerous competing pathways identified across a variety of fossil and non-fossil feedstocks, there is a need to harmonize the analyses of these pathways using a consistent techno-economic approach and compare them to current commercial pathways to better understand the benefits or limitations inherent to each technology. In this work we conduct a consistent comparative analysis of three sustainable methanol synthesis pathways versus a commercial baseline, with biomass, CO2, and natural gas as the carbon sources. The three sustainable pathways of interest are biomass gasification to syngas with subsequent catalytic conversion of syngas to methanol, indirect conversion of CO2 to syngas via electrolysis with subsequent catalytic conversion of syngas to methanol, and direct conversion of CO2 to methanol via electrolysis. To elucidate the challenges and opportunities in the path to commercialization of each sustainable pathway, we investigate five key process metrics: production cost, carbon efficiency, carbon intensity, energy efficiency, and technology readiness level (TRL).

biomass↗

DOE OSTI2024

Site-specific Design Case Study for Wet Waste Hydrothermal Liquefaction and Biocrude Upgrading to Hydrocarbon Fuels

Hydrothermal liquefaction (HTL) is a thermal process that converts wet biomass to renewable hydrocarbon fuel blendstocks (i.e., renewable naphtha, renewable diesel, and sustainable aviation fuel (SAF)). It can utilize a wide range of pure and blended wet feedstocks, including sewage sludge from water resource recovery facilities (WRRF), food and agriculture wastes, algae, fats, oils and greases (FOG) and blends of dry and wet wastes/feedstocks. Historically, techno-economic analysis (TEA) and annual state of technology (SOT) assessments with standard economic assumptions used by the Bioenergy Technologies Office (BETO) were conducted for the wet waste HTL pathway leveraging experimental data collected from Pacific Northwest National Laboratory’s (PNNL) continuous flow reactor systems. The objective of the SOT assessment has been to guide and track progress of BETO’s HTL research and development (R&D) toward reduced cost and greenhouse gas (GHG) emissions for the pathway. However, gaps exist between BETO’s traditional SOT updates and the needs of key external stakeholders that – if addressed – will accelerate technology adoption. This Business Case Study aims to bridge this gap by providing an updated design, TEA, and LCA based on PNNL’s FY23 R&D with added analyses and information that provide enhanced relevance for stakeholders of the HTL technology. This includes specific siting, regional wet waste resource inventory and transportation cost analyses, fuel market information, sustainable fuel policy impacts, economic metrics of net present value (NPV) and internal rate of return (IRR), greenhouse gas (GHG) emissions analysis, and statistical analysis of cost and technical uncertainties of the HTL plant design. The study focuses on the “Detroit combined statistical area (CSA)” region for siting of a wet waste HTL plant adjacent to the Great Lakes Water Authority (GLWA) facility with guidance from industry participants. Regional resource and siting analyses were conducted to identify feedstock availability, scale, and cost, as well as a beneficial site location. TEA with detailed rigorous capital cost estimation for the specific site application was conducted to evaluate the key economic metrics of most value to industrial partners. These include total capital investment, operating costs, minimum fuel selling price (MFSP) of the biocrude and fuel blendstock, and NPV and internal rate of return IRR with sustainable fuel credits. Life cycle analysis was conducted to evaluate the supply chain greenhouse gas (GHG) emissions for the wet waste HTL process as compared with petroleum derived diesel. This study is also informed by years of R&D and process de-risking learnings and was conducted with a basic engineering HTL plant design and costing that akin to a “first-of-a-kind” plant economics. This differs from our conventional “nth plant ” SOT assessments. Specifically, the HTL process model has been updated with more operationally reliable methods for feed heating and phase separations. Further, we have implemented additional spare equipment for redundancy, a more rigorous installed equipment cost estimation approach, and additional costs associated with feed formatting and delivery, building, piping and site development. An Excel-based cost sheet based on the basic engineering design is also released alongside the report that allows users to conduct customized TEA with their own feed composition and financial assumptions.

09 BIOMASS FUELS↗

DOE OSTI2024

Supporting data for Site-specific Design Case Study for Wet Waste Hydrothermal Liquefaction and Biocrude Upgrading to Hydrocarbon Fuels

Hydrothermal liquefaction (HTL) is a thermal process that converts wet biomass to renewable hydrocarbon fuel blendstocks (i.e., renewable naphtha, renewable diesel, and sustainable aviation fuel (SAF)). It can utilize a wide range of pure and blended wet feedstocks, including sewage sludge from water resource recovery facilities (WRRF), food and agriculture wastes, algae, fats, oils and greases (FOG) and blends of dry and wet wastes/feedstocks. Historically, techno-economic analysis (TEA) and annual state of technology (SOT) assessments with standard economic assumptions used by the Bioenergy Technologies Office (BETO) were conducted for the wet waste HTL pathway leveraging experimental data collected from Pacific Northwest National Laboratory’s (PNNL) continuous flow reactor systems. The objective of the SOT assessment has been to guide and track progress of BETO’s HTL research and development (R&D) toward reduced cost and greenhouse gas (GHG) emissions for the pathway. However, gaps exist between BETO’s traditional SOT updates and the needs of key external stakeholders that – if addressed – will accelerate technology adoption. This Business Case Study aims to bridge this gap by providing an updated design, TEA, and LCA based on PNNL’s FY23 R&D with added analyses and information that provide enhanced relevance for stakeholders of the HTL technology. This includes specific siting, regional wet waste resource inventory and transportation cost analyses, fuel market information, sustainable fuel policy impacts, economic metrics of net present value (NPV) and internal rate of return (IRR), greenhouse gas (GHG) emissions analysis, and statistical analysis of cost and technical uncertainties of the HTL plant design. The study focuses on the “Detroit combined statistical area (CSA)” region for siting of a wet waste HTL plant adjacent to the Great Lakes Water Authority (GLWA) facility with guidance from industry participants. Regional resource and siting analyses were conducted to identify feedstock availability, scale, and cost, as well as a beneficial site location. TEA with detailed rigorous capital cost estimation for the specific site application was conducted to evaluate the key economic metrics of most value to industrial partners. These include total capital investment, operating costs, minimum fuel selling price (MFSP) of the biocrude and fuel blendstock, and NPV and internal rate of return IRR with sustainable fuel credits. Life cycle analysis was conducted to evaluate the supply chain greenhouse gas (GHG) emissions for the wet waste HTL process as compared with petroleum derived diesel. This study is also informed by years of R&D and process de-risking learnings and was conducted with a basic engineering HTL plant design and costing that akin to a “first-of-a-kind” plant economics. This differs from our conventional “nth plant ” SOT assessments. Specifically, the HTL process model has been updated with more operationally reliable methods for feed heating and phase separations. Further, we have implemented additional spare equipment for redundancy, a more rigorous installed equipment cost estimation approach, and additional costs associated with feed formatting and delivery, building, piping and site development. An Excel-based cost sheet based on the basic engineering design is also released alongside the report that allows users to conduct customized TEA with their own feed composition and financial assumptions.

Li, Shuyun↗

DOE OSTI2020

Printing polymer blends through in situ active mixing during fused filament fabrication

Fused filament fabrication (FFF) enables production of 3D objects over a range of material compositions at low-cost relative to traditional manufacturing approaches. To date, a limited but growing number of materials are able to be used with FFF, however many applications exist where specific mechanical, thermal, or chemical properties are needed that cannot currently be met with the available feedstock selection. Therefore, a need exists to tune these materials for specific chemical or mechanical properties. One common formulation strategy to address these demanding design parameters is to develop composites or polymer blend filaments. Typically, this is a time-consuming and costly optimization process. Here, we have developed hardware for reproducibly mixing two filaments of similar or dissimilar compositions at the time of printing within individual printed layers. This mixing occurs via software-controlled rotating hardware in the chamber of an extruder’s hot-end. The efficiency of mixing within the printed layers has been characterized in detail as a function of the rotational speed and geometry of the blending hardware. These parameters were exploited to program the ratio and distribution of thermoplastic-based filaments blended within printed extrudate. Example printed specimens were produced with thermoplastic polyurethane (TPU) elastomer blended with rigid polylactic acid (PLA) and Nylon blended with PLA. In addition, a conductive carbon nanotube (CNT)-PLA composite was blended as a function of mixer geometry and input feed ratios with non-conductive PLA and resistance values were measured across the resulting printed specimens.

36 MATERIALS SCIENCE↗