SEARCH · Search NASA

Results for “flat models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Linear and nonlinear aspects of snow albedo feedbacks in atmospheric models

Namias' hypothesis, that anomalous snowcover on the eastern side of the North American continent can generate an anomalous east coast low pressure system and an anomalous inland high pressure system, is consistent with the time-averaged anomalous response from a nonlinear, primitive equation channel model with an idealized, flat land-sea arrangement. An attempt to understand and describe this anomalous response in the nonlinear model as a linear response to anomalous diabatic heating was largely unsuccessful, primarily because the anomalous eddy fluxes were also important. This unsuccessful attempt to describe the nonlinear model's time averages by linear theory then motivated several comparisons between linear and nonlinear severely truncated quasi-geostrophic models. It was also found in these models that the eddy fluxes were extremely important for forcing or dissipating the stationary eddies.

Roads, J. O.↗

NASA NTRS1959

The Effect of Beam Loading on Water Impact Loads and Motions

An investigation of the effect of beam loading on impact loads and motions has been conducted in the Langley impact basin. Water impact tests of flat-bottom 5-inch-and 8-inch-beam models having beam-loading coefficients C(sub Delta) from 62.5 to 544 and a 30 deg dead-rise 5-inch-beam model A having beam-loading coefficients from 208 to 530 are described and the results analyzed to show trends of these heavy-beam-loading data with initial flight-path angle, trim angle, dead-rise angle, and time through- out the impact. Data from flat-bottom model tests, C(sub Delta) = 4.4 to 36.5, and from 30 deg dead-rise model tests, C(sub Delta) = 0.58 and 18.8, are included, along with the heavy-beam-loading data; and variations of these data with beam-loading coefficients are shown. Each of the load and motion coefficients is found to be directly proportional to a power factor of C(sub Delta). For instance, the maximum impact lift coefficient is found C(sub L,max) to be directly proportional to C(sub Delta, exp 0,33) for the flat-bottom model and C(sub Delta, exp 0,45) for the 30 deg dead-rise model. These variations of C(sub L, max) with C(sub Delta) are found to be in agreement with theoretical variations. Finally, an empirical equation for the prediction of C(sub L,max) is presented and is shown to give good agreement with experimental C(sub L, max) for about 500 fixed-trim smooth-water impacts. The range of variables included dead-rise angles from 0 deg to deg, beam-loading coefficients from o.48 to 544, trim angles from 3 deg to deg, and initial flight-path angles from about 2 deg to about deg.

Mixson, John S.↗

NASA NTRS1974

Wind tunnel investigation of a large-scale semispan model with an unswept wing and an upper-surface blown jet flat

An investigation of the static longitudinal aerodynamic characteristics of a large-scale semispan model with an unswept wing and an upper-surface blown jet flap for lift augmentation was conducted in the Langley full-scale tunnel. The wing had an aspect ratio of 7.8 (3.9 for the semispan) and a simulated turbofan engine mounted ahead of and above the wing in a nacelle with a rectangular-exit nozzle. The flap system had three spanwise flap segments: (1) an inboard plain flap located behind the engine and having a large radius of curvature to provide a smooth upper surface to enhance the turning of the jet sheet, (2) a double-slotted midspan flap, and (3) a drooped aileron equipped with blowing boundary-layer control. The wing was also equipped with a full-span leading-edge Krueger flap with blowing boundary-layer control. In addition to the aerodynamic measurements, noise measurements were also included in the investigation for positions above and below the wing.

Smith, C. C., Jr.↗

NASA NTRS1992

Anisotropies of the cosmic microwave background in nonstandard cold dark matter models

Small angular scale cosmic microwave anisotropies in flat, vacuum-dominated, cold dark matter cosmological models which fit large-scale structure observations and are consistent with a high value for the Hubble constant are reexamined. New predictions for CDM models in which the large-scale power is boosted via a high baryon content and low H(0) are presented. Both classes of models are consistent with current limits: an improvement in sensitivity by a factor of about 3 for experiments which probe angular scales between 7 arcmin and 1 deg is required, in the absence of very early reionization, to test boosted CDM models for large-scale structure formation.

Vittorio, Nicola↗

NASA NTRS1976

Space shuttle prototype check valve development

Contaminant-resistant seal designs and a dynamically stable prototype check valve for the orbital maneuvering and reaction control helium pressurization systems of the space shuttle were developed. Polymer and carbide seal models were designed and tested. Perfluoroelastomers compatible with N2O4 and N2H4 types were evaluated and compared with Teflon in flat and captive seal models. Low load sealing and contamination resistance tests demonstrated cutter seal superiority over polymer seals. Ceramic and carbide materials were evaluated for N2O4 service using exposure to RFNA as a worst case screen; chemically vapor deposited tungsten carbide was shown to be impervious to the acid after 6 months immersion. A unique carbide shell poppet/cutter seat check valve was designed and tested to demonstrate low cracking pressure ( 2.0 psid), dynamic stability under all test bench flow conditions, contamination resistance (0.001 inch CRES wires cut with 1.5 pound seat load) and long life of 100,000 cycles (leakage 1.0 scc/hr helium from 0.1 to 400 psig).

Tellier, G. F.↗

NASA NTRS1983

Metallic alloy stability studies

The dimensional stability of candidate cryogenic wind tunnel model materials was investigated. Flat specimens of candidate materials were fabricated and cryo-cycled to assess relative dimensional stability. Existing 2-dimensional airfoil models as well as models in various stages of manufacture were also cryo-cycled. The tests indicate that 18 Ni maraging steel offers the greatest dimensional stability and that PH 13-8 Mo stainless steel is the most stable of the stainless steels. Dimensional stability is influenced primarily by metallurgical transformations (austenitic to martensitic) and manufacturing-induced stresses. These factors can be minimized by utilization of stable alloys, refinement of existing manufacturing techniques, and incorporation of new manufacturing technologies.

Firth, G. C.↗

NASA NTRS2026

Impact Testing of 410 Stainless Steel for Material Impact Model Development

A project is underway to develop a consistent set of material properties, impact test data, and failure analysis for a variety of metallic aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the Federal Aviation Administration William J. Hughes Technical Center. Particular features of this set of data are that all material property and impact test data are obtained using traceable material, the test methods and procedures are extensively documented, and all the raw data are available. Four parallel efforts are currently underway: measurement of material deformation and failure response over a wide range of strain rates and temperatures, failure analysis of material property specimens and impact test articles, development of improved numerical modeling techniques for deformation and failure, and impact testing of flat panels and substructures for model validation. This report describes impact testing performed on 410 stainless steel sheet and plate samples of different thicknesses with two different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

410 Stainless Steel↗

NASA NTRS1982

On the cause of the flat-spot phenomenon observed in silicon solar cells at low temperatures and low intensities

A model that explains the flat-spot power loss phenomenon is presented. Evidence suggests that the effect is due to localized metallurgical interactions between the silicon substrate and the contact metallization. These reactions are shown to result in localized regions in which the P-N junction is destroyed and replaced with a metal semiconductor-like interface. The effects of thermal treatment, crystallographic orientation, junction depth, and metallization are shown along with a method of preventing the effect through the suppression of vacancy formation at the free surface of the contact metallization. Data indicating the effectiveness of a TiN diffusion barrier in preventing the effect are also given.

Weizer, V. G.↗

NASA NTRS2021

The Asymmetric Inner Disk of the Herbig Ae Star HD 163296 in the Eyes of VLTI/MATISSE: Evidence for a Vortex?

Context.A complex environment exists in the inner few astronomical units of planet-forming disks. High-angular-resolution observa-tions play a key role in our understanding of the disk structure and the dynamical processes at work.Aims.In this study we aim to characterize the mid-infrared brightness distribution of the inner disk of the young intermediate-massstar HD 163296 from early VLTI/MATISSE observations taken in theL- andN-bands. We put special emphasis on the detection ofpotential disk asymmetries.Methods.We use simple geometric models to fit the interferometric visibilities and closure phases. Our models include a smoothedring, a flat disk with an inner cavity, and a 2D Gaussian. The models can account for disk inclination and for azimuthal asymmetriesas well. We also perform numerical hydrodynamical simulations of the inner edge of the disk.Results.Our modeling reveals a significant brightness asymmetry in theL-band disk emission. The brightness maximum of the asym-metry is located at the NW part of the disk image, nearly at the position angle of the semimajor axis. The surface brightness ratio inthe azimuthal variation is3.5±0.2. Comparing our result on the location of the asymmetry with other interferometric measurements,we confirm that the morphology of ther<0.3au disk region is time-variable. We propose that this asymmetric structure, located in ornear the inner rim of the dusty disk, orbits the star. To find the physical origin of the asymmetry, we tested a hypothesis where a vortexis created by Rossby wave instability, and we find that a unique large-scale vortex may be compatible with our data. The half-lightradius of theL-band-emitting region is0.33±0.01au, the inclination is52◦+5◦−7◦, and the position angle is143◦±3◦. Our models predictthat a non-negligible fraction of theL-band disk emission originates inside the dust sublimation radius forμm-sized grains. Refractorygrains or large (&10μm-sized) grains could be the origin of this emission.N-band observations may also support a lack of smallsilicate grains in the innermost disk (r.0.6au), in agreement with our findings fromL-band data.

J Varga↗

NASA NTRS1947

Free-Spinning and Tumbling Tests of a 1/16-Scale Model of the McDonnell XP-85 Airplane

The teat results showed that with either of the three tail arrangements, the model usually spun in flat attitudes with oscillations about the lateral and longitudinal axes. In general, full reversal of the rudder pedals did not stop the spinning rotation. To make the model satisfactorily meet-the spin-recovery requirements it was found that installation of either a very large ventral fin (l7.9 square feet, full scale) below the tail or a somewhat smaller ventral fin and rudder (12.4 square feet, total . full-scale area) with a rudder throw of at least +/-22deg was required. Either a 21.3-foot tail parachute or a 6.4-foot wing-tip parachute (drag coefficient approximately 0.70) appears necessary as an emergency spin-recovery device during demonstration spins.

Klinar, Walter J.↗

NASA NTRS1987

Flight investigation of the effect of tail configuration on stall, spin, and recovery characteristics of a low-wing general aviation research airplane

Flight tests were performed to investigate the stall, spin, and recovery characteristics of a low-wing, single-engine, light airplane with four interchangeable tail configurations. The four tail configurations were evaluated for effects of varying mass distribution, center-of-gravity position, and control inputs. The airplane tended to roll-off at the stall. Variations in tail configuration produced spins ranging from 40 deg to 60 deg angle of attack and turn rates of about 145 to 208 deg/sec. Some unrecoverable flat spins were encountered which required use of the airplane spin chute for recovery. For recoverable spins, antispin rudder followed by forward wheel with ailerons centered provided the quickest spin recovery. The moderate spin modes agreed very well with those predicted from spin-tunnel model tests, however, the flat spin was at a lower angle of attack and a slower rotation rate than indicated by the model tests.

Stough, H. Paul, III↗

NASA NTRS1982

Reliability and performance experience with flat-plate photovoltaic modules

Statistical models developed to define the most likely sources of photovoltaic (PV) array failures and the optimum method of allowing for the defects in order to achieve a 20 yr lifetime with acceptable performance degradation are summarized. Significant parameters were the cost of energy, annual power output, initial cost, replacement cost, rate of module replacement, the discount rate, and the plant lifetime. Acceptable degradation allocations were calculated to be 0.0001 cell failures/yr, 0.005 module failures/yr, 0.05 power loss/yr, a 0.01 rate of power loss/yr, and a 25 yr module wear-out length. Circuit redundancy techniques were determined to offset cell failures using fault tolerant designs such as series/parallel and bypass diode arrangements. Screening processes have been devised to eliminate cells that will crack in operation, and multiple electrical contacts at each cell compensate for the cells which escape the screening test and then crack when installed. The 20 yr array lifetime is expected to be achieved in the near-term.

Ross, R. G., Jr.↗

NASA NTRSDate not supplied

Simulation of Dynamic Crushing Behavior of Simulated Carbon/Epoxy Stanchions Using MAT58 and MAT213 in LS-DYNA

Carbon fiber-reinforced polymer (CFRP) composites have shown promise as a material for structures designed to absorb energy in crush-style impact loading. In complementing the lightweight and tailorable characteristics of CFRP structures, the benefits of impact energy absorption are particularly interesting in aerospace vehicles that require excellent crashworthiness performance. However, simulating the behavior of CFRP structures in dynamic, crushing-style impact loading is challenging because of the many damage and failure modes that are essential to capture in the model. For the present investigation, CFRP stanchions were tested using a crash sled experimental test rig. The stanchions were designed by the Composite Materials Handbook-17 (CMH-17) Crashworthiness Working Group for the purpose of comparing experimental crash sled tests to corresponding simulations of the tests. The stanchions are C-channel shaped and represent a geometry common in the interior of aerospace vehicle structures. Explicit simulations in LSDYNA were performed using a well-established composite material model (MAT58) and a next-generation material model (MAT213). Fully integrated shell elements were utilized instead of 3D solid elements to limit computation time. In all models, each of the sixteen plies were represented with individual layers of shell elements with tiebreak contact between each adjacent ply pair to simulate interlaminar fracture. Simulating the crushing of the stanchions occurred in two phases. First, the material models were calibrated using flat specimens that were manufactured with the same layup as the stanchions. While the original goal was calibration of material-related properties, meshdependent behavior was observed in simulations with either material model, and an unstructured mesh was selected to remediate undesirable mesh-dependent failure modes. Additionally, for both the MAT58 and MAT213 models, it was found that either the crush force or the failure mode could be modeled accurately, but no set of parameters could be identified to attain both results in the same model. Once satisfactory calibration was achieved, the same material parameters were applied to the stanchion crush simulations. The stanchion simulations showed that MAT213 more accurately predicted the experimentally determined crush force, and both material models predicted key aspects of the experimentally observed failure modes.

Composite Materials↗

NASA NTRS1972

Exploratory investigation of sound pressure level in the wake of an oscillating airfoil in the vicinity of stall

Wind tunnel tests were performed on two oscillating two-dimensional lifting surfaces. The first of these models had an NACA 0012 airfoil section while the second simulated the classical flat plate. Both of these models had a mean angle of attack of 12 degrees while being oscillated in pitch about their midchord with a double amplitude of 6 degrees. Wake surveys of sound pressure level were made over a frequency range from 16 to 32 Hz and at various free stream velocities up to 100 ft/sec. The sound pressure level spectrum indicated significant peaks in sound intensity at the oscillation frequency and its first harmonic near the wake of both models. From a comparison of these data with that of a sound level meter, it is concluded that most of the sound intensity is contained within these peaks and no appreciable peaks occur at higher harmonics. It is concluded that within the wake the sound intensity is largely pseudosound while at one chord length outside the wake, it is largely true vortex sound. For both the airfoil and flat plate the peaks appear to be more strongly dependent upon the airspeed than on the oscillation frequency. Therefore reduced frequency does not appear to be a significant parameter in the generation of wake sound intensity.

Gray, R. B.↗

NASA NTRS2017

Growth Angle: A Microscopic View

A microscopic continuum mechanical model of the growth angle is proposed. It is based on the van der Waals type framework that is used for surface force phenomena. The obtained augmented Laplace type integro-differential equations are, in general, difficult to analyze. Here we focused primarily on the particular case of equal melt and crystal surface energies. We derived an approximate equation for the meniscus shape, and obtained an analytical relationship between the contact and the growth angle. Interestingly, the same result can be obtained using the macroscopic model of Herring. The case of a macroscopically sharp corner is also considered. For this case, the macroscopic angle is not defined and it can be any angle between the contact angles of both flat surfaces. The microscopic model yields the smooth shape for the meniscus that also is not unique, but depends on the initial position of the meniscus.

Mazuruk, Konstantin↗

NASA NTRS2015

L'CO/LFIR Relations with CO Rotational Ladders of Galaxies Across the Herschel SPIRE Archive

We present a catalog of all CO (carbon monoxide) (J (total angular momentum quantum number) equals 1-0 through J equals 13-12), [CI], and [NII] lines available from extragalactic spectra from the Herschel SPIRE (Spectral and Photometric Imaging Receiver) Fourier Transform Spectrometer (FTS) archive combined with observations of the low-J CO lines from the literature and from the Arizona Radio Observatory. This work examines the relationships between L (sub FIR (Far Infra Red)), L prime (sub CO), and L (sub CO) / L (sub CO, 1-0). We also present a new method for estimating probability distribution functions (PDFs) from marginal signal-to-noise ratio Herschel FTS spectra, which takes into account the instrumental "ringing" and the resulting highly correlated nature of the spectra. The slopes of Log (L (sub FIR)) versus Log (L prime (sub CO)) are linear for all mid- to high-J CO lines. The mid- to high-J CO luminosity relative to CO J equals 1-0 increases with increasing L (sub FIR), indicating higher excitement of the molecular gas, though these ratios do not exceed approximately 100. The luminosities relative to CO J equals 1-0 remain relatively at from J equals 6-5 through J equals13-2, across many orders of magnitude of L (sub FIR). Qualitative comparisons to current theoretical models do not match these flat SLED (spectral line energy distributions) shapes, indicating the need for more comprehensive modeling of the excitation processes of warm molecular gas in nearby galaxies.

Submillimeter Data↗

NASA NTRS2020

Simulation and Modeling of Cold-Wall Hypersonic Turbulent Boundary Layers on Flat Plate

Direct numerical simulations (DNS) of flat-plate, zero-pressure-gradient turbulent boundary layers are presented for nominal freestream Mach numbers of 11 and 14 and a highly cooled wall (wall-to-recovery temperature of approximately 0.2). The flow conditions of the DNS are representative of the experimental data for a Mach 11.1 turbulent boundary layer on a flat plate that was tested at Calspan–University of Buffalo Research Center (CUBRC) and the operational conditions of the AEDC Hypervelocity Tunnel No. 9 at Mach 14. The wall shear stress and turbulent heat flux predicted by DNS show good comparisons with those measured at CUBRC and those modeled with a Baldwin-Lomax model. The generated DNS database extends the range of Reynolds numbers from those typical of previous DNS studies for hypersonic boundary-layer flows and confirms the validity of Morkovin’s hypothesis within the relatively broader range of Reynolds numbers considered in this study. A priori assessment of turbulent heat flux models with DNS data shows that the algebraic energy flux (AEF) formulation gives better predictions of the streamwise turbulent heat flux than the commonly used constant turbulent Prandtl number model while both models give similarly good predictions of the wall-normal turbulent heat flux. A posteriori assessment shows that the AEF model improves the prediction of the temperature profiles while keeping a good prediction of the velocity field.

Junji Huang↗

NASA NTRS2013

Nine-Year Wilkinson Microwave Anisotropy Probe (WMAP) Observations: Final Maps and Results

We present the final nine-year maps and basic results from the Wilkinson Microwave Anisotropy Probe (WMAP) mission. The full nine-year analysis of the time-ordered data provides updated characterizations and calibrations of the experiment. We also provide new nine-year full sky temperature maps that were processed to reduce the asymmetry of the effective beams. Temperature and polarization sky maps are examined to separate cosmic microwave background (CMB) anisotropy from foreground emission, and both types of signals are analyzed in detail.We provide new point source catalogs as well as new diffuse and point source foreground masks. An updated template-removal process is used for cosmological analysis; new foreground fits are performed, and new foreground reduced are presented.We nowimplement an optimal C(exp -1)1 weighting to compute the temperature angular power spectrum. The WMAP mission has resulted in a highly constrained Lambda-CDM cosmological model with precise and accurate parameters in agreement with a host of other cosmological measurements. When WMAP data are combined with finer scale CMB, baryon acoustic oscillation, and Hubble constant measurements, we find that big bang nucleosynthesis is well supported and there is no compelling evidence for a non-standard number of neutrino species (N(sub eff) = 3.84 +/- 0.40). The model fit also implies that the age of the universe is (sub 0) = 13.772 +/- 0.059 Gyr, and the fit Hubble constant is H(sub 0) = 69.32 +/- 0.80 km/s/ Mpc. Inflation is also supported: the fluctuations are adiabatic, with Gaussian random phases; the detection of a deviation of the scalar spectral index from unity, reported earlier by the WMAP team, now has high statistical significance (n(sub s) = 0.9608+/-0.0080); and the universe is close to flat/Euclidean (Omega = −0.0027+0.0039/−0.0038). Overall, the WMAP mission has resulted in a reduction of the cosmological parameter volume by a factor of 68,000 for the standard six-parameter Lambda-CDM model, based on CMB data alone. For a model including tensors, the allowed seven-parameter volume has been reduced by a factor 117,000. Other cosmological observations are in accord with the CMB predictions, and the combined data reduces the cosmological parameter volume even further.With no significant anomalies and an adequate goodness of fit, the inflationary flat Lambda-CDM model and its precise and accurate parameters rooted in WMAP data stands as the standard model of cosmology.

dark matter↗