Search NASA⌕ Search

SEARCH · Search NASA

Results for “flexible structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Projection filters for modal parameter estimate for flexible structures

Single-mode projection filters are developed for eigensystem parameter estimates from both analytical results and test data. Explicit formulations of these projection filters are derived using the pseudoinverse matrices of the controllability and observability matrices in general use. A global minimum optimization algorithm is developed to update the filter parameters by using interval analysis method. Modal parameters can be attracted and updated in the global sense within a specific region by passing the experimental data through the projection filters. For illustration of this method, a numerical example is shown by using a one-dimensional global optimization algorithm to estimate model frequencies and dampings.

Huang, Jen-Kuang↗
NASA NTRS1987

On the control of flexible structures by applied thermal gradients

Thermal, elastic, and feedback analyses are applied to the case of a beam with a distributed thermal actuator. The actuator is capable of producing a thermal gradient across the section of the beam. One candidate for such an actuator uses the Peltier effect, which appears in certain semiconductors. These devices act as heat pumps when a voltage is applied, causing a temperature gradient. It is shown that the thermal gradients can induce deflection in the beam. If the thermal gradients are applied in the proper sense to a vibrating beam, it is possible to increase the vibration damping exhibited by the structure. Experimental results are given for a cantilever beam, whose first vibrational mode damping ratio was increased from 0.81 to 7.4 percent with a simple lead compensation.

Edberg, D. L.↗
NASA NTRS1987

Control of flexible structures by applied thermal gradients

Thermal, elastic, and feedback analyses are applied to the case of a beam with a distributed thermal actuator. The actuator is capable of producing a thermal gradient across the section of the beam. One candidate for such an actuator uses the Peltier effect, which appears in certain semiconductors. These devices act as heat pumps when a voltage is applied, causing a temperature gradient. It is shown that the thermal gradients can induce deflection in the beam. If the thermal gradients are applied in the proper sense to a vibrating beam, it is possible to increase the vibration damping exhibited by the structure. Experimental results are given for a cantilever beam, whose first vibrational mode damping ratio was increased from 0.81 to 7.4 percent with simple lead compensation.

Edberg, Donald L.↗
NASA NTRS1987

Robust eigensystem assignment for flexible structures

An improved method is developed for eigenvalues and eigenvectors placement of a closed-loop control system using either state or output feedback. The method basically consists of three steps. First, the singular value of QR decomposition is used to generate an orthonormal basis that spans admissible eigenvector space corresponding to each assigned eigenvalue. Secondly, given a unitary matrix, the eigenvector set which best approximates the given matrix in the least-square sense and still satisfy eigenvalue cosntraints is determined. Thirdly, a unitary matrix is sought to minimize the error between the unitary matrix and the assignable eigenvector matrix. For use as the desired eigenvector set, two matrices, namely, the open-loop eigenvector matrix and its closest unitary matrix are proposed. The latter matrix generally encourages both minimum conditioning and control gains. In addition, the algorithm is formulated in real arithmetic for efficient implementation. To illustrate the basic concepts, numerical examples are included.

Juang, Jer-Nan↗
NASA NTRS1987

Single-mode projection filters for identification and state estimation of flexible structures

Single-mode projection filters are developed for eigensystem parameter identification and state estimation from both analytical results and test data. Explicit formulations of these projection filters are derived using the pseudoinverse matrices of the controllabilty and observability matrices in the general sense. A global minimum optimization algorithm is developed to update the filter parameters by using the interval analysis method. Modal parameters can be identified and updated in the global sense within a specified region of parameters by passing the experimental data through the projection filters. For illustration of this new approach, a numerical example is shown by using a one-dimensional global optimization algorithm to estimate modal frequencies and damping.

Huang, Jen-Kuang↗
NASA NTRS1988

Single-Mode Projection Filters for Modal Parameter Identification for Flexible Structures

Single-mode projection filters are developed for eigensystem parameter identification from both analytical results and test data. Explicit formulations of these projection filters are derived using the orthogonal matrices of the controllability and observability matrices in the general sense. A global minimum optimization algorithm is applied to update the filter parameters by using the interval analysis method. The updated modal parameters represent the characteristics of the test data. For illustration of this new approach, a numerical simulation for the MAST beam structure is shown by using a one-dimensional global optimization algorithm to identify modal frequencies and damping. Another numerical simulation of a ten-mode structure is also presented by using a two-dimensional global optimization algorithm to illustrate the feasibility of the new method. The projection filters are practical for parallel processing implementation.

Huang, Jen-Kuang↗
NASA NTRS1987

Robustness issues in boundary feedback of flexible structures

Transfer function models for basic structural elements with boundary control reveal certain inherent properties relevant to questions of control system realization, design, and analysis of robustness. The transfer functions involved are not strictly proper, may be nonminimum phase (except for the special case of colocated actuation and sensing), and often have large number of poles on the imaginary axis. In this paper these basic questions are considered in terms of modeling and control system design for robustness. The application of algebraic methods for computing stabilizing control, based on certain exact, irrational transfer functions is investigated. Boundary control of the wave equation is considered and extension of the method to more general problems is suggested. Special attention is given to implementation issues associated with a class of infinite dimensional control laws.

Bennett, W. H.↗
NASA NTRS1987

SHAPES - Spatial, High-Accuracy, Position-Encoding Sensor for multi-point, 3-D position measurement of large flexible structures

An electro-optical position sensor for precise simultaneous measurement of the 3-D positions of multiple points on large space structures is described. The sensor data rate is sufficient for most control purposes. Range is determined by time-of-flight correlation of short laser pulses returned from retroreflector targets using a streak tube/CCD detector. Angular position is determined from target image locations on a second CCD. Experimental verification of dynamic ranging to multiple targets is discussed.

Nerheim, N. M↗
NASA NTRS1988

Adaptive control experiment with a large flexible structure

A large space antenna-like ground experiment structure has been developed for conducting research and validation of advanced control technology. A set of proof-of-concept adaptive control experiments for transient and initial deflection regulation with a small set of sensors and actuators were conducted. Very limited knowledge of the plant dynamics and its environment was used in the design of the adaptive controller so that performance could be demonstrated under conditions of gross underlying uncertainties. High performance has been observed under such stringent conditions. These experiments have established a baseline for future studies involving more complex hardware and environmental conditions, and utilizing additional sets of sensors and actuators.

Ih, Che-Hang Charles↗
NASA NTRS1987

Sensitivity, optimal scaling and minimum roundoff errors in flexible structure models

Traditional modeling notions presume the existence of a truth model that relates the input to the output, without advanced knowledge of the input. This has led to the evolution of education and research approaches (including the available control and robustness theories) that treat the modeling and control design as separate problems. The paper explores the subtleties of this presumption that the modeling and control problems are separable. A detailed study of the nature of modeling errors is useful to gain insight into the limitations of traditional control and identification points of view. Modeling errors need not be small but simply appropriate for control design. Furthermore, the modeling and control design processes are inevitably iterative in nature.

Skelton, Robert E.↗
NASA NTRS1988

Experiences in applying optimization techniques to configurations for the Control Of Flexible Structures (COFS) Program

Optimization procedures are developed to systematically provide closely-spaced vibration frequencies. A general-purpose finite-element program for eigenvalue and sensitivity analyses is combined with formal mathematical programming techniques. Results are presented for three studies. The first study uses a simple model to obtain a design with two pairs of closely-spaced frequencies. Two formulations are developed: an objective function-based formulation and constraint-based formulation for the frequency spacing. It is found that conflicting goals are handled better by a constraint-based formulation. The second study uses a detailed model to obtain a design with one pair of closely-spaced frequencies while satisfying requirements on local member frequencies and manufacturing tolerances. Two formulations are developed. Both the constraint-based and the objective function-based formulations perform reasonably well and converge to the same results. However, no feasible design solution exists which satisfies all design requirements for the choices of design variables and the upper and lower design variable values used. More design freedom is needed to achieve a fully satisfactory design. The third study is part of a redesign activity in which a detailed model is used. The use of optimization in this activity allows investigation of numerous options (such as number of bays, material, minimum diagonal wall thicknesses) in a relatively short time. The procedure provides data for judgments on the effects of different options on the design.

Walsh, Joanne L.↗
NASA NTRS1989

Experiences in applying optimization techniques to configurations for the Control of Flexible Structures (COFS) program

Optimization procedures are developed to systematically provide closely-spaced vibration frequencies. A general purpose finite-element program for eigenvalue and sensitivity analyses is combined with formal mathematical programming techniques. Results are presented for three studies. The first study uses a simple model to obtain a design with two pairs of closely-spaced frequencies. Two formulations are developed: an objective function-based formulation and constraint-based formulation for the frequency spacing. It is found that conflicting goals are handled better by a constraint-based formulation. The second study uses a detailed model to obtain a design with one pair of closely-spaced frequencies while satisfying requirements on local member frequencies and manufacturing tolerances. Two formulations are developed. Both the constraint-based and the objective function-based formulations perform reasonably well and converge to the same results. However, no feasible design solution exists which satisfies all design requirements for the choices of design variables and the upper and lower design variable values used. More design freedom is needed to achieve a fully satisfactory design. The third study is part of a redesign activity in which a detailed model is used.

Walsh, Joanne L.↗
NASA NTRS1989

Sensor failure detection using generalized parity relations for flexible structures

Analytical redundancy may be preferable to hardware redundancy in failure detection/isolation tasks for such large-scale systems as space structures. Generalized single-sensor parity relations are presently applied to this problem; they are noted to yield a very simple isolation logic, and their generation is found to be extremely rapid, even in the case of extremely complex systems, provided only that the eigenstructure of the system be known. Their implementation is, however, extremely sensitive to modeling errors and noise.

Mercadal, Mathieu↗
NASA NTRS1989

A planar comparison of actuators for vibration control of flexible structures

The methods and results of an analytical study comparing the effectiveness of four actuators in damping the vibrations of a planar clamped-free beam are presented. The actuators studied are two inertia-type actuators, the proof mass and reaction wheel, and two variable geometry trusses, the planar truss and the planar truss proof mass (a combination variable geometry truss/inertia-type actuator). Actuator parameters used in the models were chosen based on the results of a parametric study. A full-state, LQR optimal feedback control law was used for control in each system. Numerical simulations of each beam/actuator system were performed in response to initial condition inputs. These simulations provided information such as time response of the closed-loop system and damping provided to the beam. This information can be used to determine the 'best' actuator for a given purpose.

Clark, William W.↗