Search NASA⌕ Search

SEARCH · Search NASA

Results for “float zone”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Laser-assisted solar cell metallization processing

The status of the laser-assisted solar cell metallization processing is described. Metallo-organic silver films were spun-on by argon ion laser beam pyrolysis. The metallo-organic decomposition (MOD) film was spun-on an evaporated Ti/Pd film to produce tood adhesion. In a maskless process, the argon ion laser writes the contact pattern. The film is then built up to obtain the required conductivity using conventional silverplating process. The Ti/Pd film in the field is chemically etched using the plated silver film as the mask. The width of the contact pattern is determined by the power of the laser. Widths as thin as 20 microns were obtained using 0.66 W of laser power. Cells fabricated with the 50 micron line widths of 4 ohm-cm floating zone (Fz) silicon-produced efficiencies of 16.6% (no passivation) which were equivalent to the best cells using conventional metallization/lithography and no passivation.

Meier, D. L.↗
NASA NTRS1986

Use of low-energy hydrogen ion implants in high-efficiency crystalline-silicon solar cells

The use of low-energy hydrogen implants in the fabrication of high-efficiency crystalline silicon solar cells was investigated. Low-energy hydrogen implants result in hydrogen-caused effects in all three regions of a solar cell: emitter, space charge region, and base. In web, Czochralski (Cz), and floating zone (Fz) material, low-energy hydrogen implants reduced surface recombination velocity. In all three, the implants passivated the space charge region recombination centers. It was established that hydrogen implants can alter the diffusion properties of ion-implanted boron in silicon, but not ion-implated arsenic.

Fonash, S. J.↗
NASA NTRS1987

Processing and characterization of high-efficiency

Silicon solar cells with efficiencies ranging from 17 to 17.7 percent are described. These cells were processed on low-resistivity FZ substrates using techniques recently developed for high efficiency terrestrial solar cells. Preliminary results indicate that the high efficiency cell is more susceptible to radiation damage in that it retains a smaller proportion of its original power output when compared to conventional space cells after exposure to 5 times 10 to the 14th power 1 MeV electrons. However, the cell does maintain a greater overall power output than the conventional cells to which it was compared. Furthermore, this cell does not demonstrate post-electron irradiation photon decay as has been described for cells processed on 1-10 ohm-cm float zone silicon.

Crotty, G. T.↗
NASA NTRS1986

High-efficiency silicon solar cells - Development, current issues and future directions

This paper provides a review of material, process, and design considerations that are essential for achieving high-efficiency silicon solar cells. It describes an approach that resulted in 18.0-18.5-percent-efficient cells on low-resistivity float-zone silicon material. It is shown experimentally that a combination of surface passivation and double-layer antireflection coating can provide 2-3 percent (absolute) improvement in cell efficiency provided the material, process and cell design are carefully selected.

Rohatgi, A.↗
NASA NTRS1986

Materials processing in space - Review of the early experiments

Basic research performed to study various aspects of fluid behavior in a microgravity environment during the first two decades of spaceflight is described. The uniqueness of space was recognized in the 1950s as a place where buoyancy-driven convective flows and sedimentation would effectively be absent. The conditions were favorable for experiments in crystal growth, alloy solidification, combustion, thermocapillary flows, electroosmotic flows, Stefan flows, Soret diffusion, and solidification processes. Pre-Skylab NASA drop tower experiments and Apollo 14 and 17 experiments made in preparation for Skylab are described. Skylab welding and brazing, crystal growth, metallurgy and liquid float zone trials and Apollo-Soyuz crystal growth, electrophoresis and metallurgical experiments are summarized. SPAR rocket trials along similar lines are also outlined.

Naumann, Robert J.↗
NASA NTRS1987

Performance improvements in silicon flat-plate cells and modules

This paper reports the development of a flat-plate module based on highly efficient ion-implanted silicon solar cells. The cells developed in this work are 53 sq cm in area and have exhibited AM 1.5 efficiencies of over 18 percent. The use of back surface reflectors to reduce module operating temperature is discussed. A comparison of various approaches to cell design is made, and module test data for these designs are presented. A comparison of float zone and Czochralski silicon is made. Module efficiency of over 15 percent (at 25 C) is reported.

Spitzer, M. B.↗
NASA NTRS1987

Development of a new generation of high-temperature composite materials

There are ever-increasing demands to develop low-density materials that maintain high strength and stiffness properties at elevated temperatures. Such materials are essential if the requirements for advanced aircraft, space power generation, and space station plans are to be realized. Metal matrix composites and intermetallic matrix composites are currently being investigated at NASA Lewis for such applications because they offer potential increases in strength, stiffness, and use temperature at a lower density than the most advanced single-crystal superalloys presently available. Today's discussion centers around the intermetallic matrix composites proposed by Lewis for meeting advanced aeropropulsion requirements. The fabrication process currently being used at Lewis to produce intermetallic matrix composites will be reviewed, and the properties of one such composite, SiC/Ti3Al+Nb, will be presented. In addition, the direction of future research will be outlined, including plans for enhanced fabrication of aluminide composites by the arc spray technique and fiber development by the floating-zone process.

Brindley, Pamela K.↗
NASA NTRS1987

The economic payoff for a state-of-the-art high-efficiency flat-plate crystalline silicon solar cell technology

In 1986 during the flat-plate solar array project, silicon solar cells 4.0 sq cm in area were fabricated at the Jet Propulsion Laboratory (JPL) with a conversion efficiency of 20.1 percent (AM1.5-global). Sixteen cells were processed with efficiencies measuring 19.5 percent (AM1.5 global) or better. These cells were produced using refined versions of conventional processing methods, aside from certain advanced techniques that bring about a significant reduction in a major mechanism (surface recombination) that limits cell efficiency. Wacker Siltronic p-type float-zone 0.18-ohm-cm wafers were used. Conversion efficiencies in this range have previously been reported by other researchers, but generally on much smaller (0.5 vs. 4.0 cm) devices which have undergone sophisticated and costly processing steps. An economic analysis is presented of the potential payoffs for this approach, using the Solar Array Manufacturing Industry Costing Standards (SAMICS) methodology. The process sequence used and the assumptions made for capturing the economies of scale are presented.

Bickler, Donald B.↗
NASA NTRS1990

Sensitivity of liquid bridges subject to axial residual acceleration

It has become evident that the float zone crystal growth method and isothermal liquid bridges may be very sensitive to the residual acceleration environment of a spacelab. Using a slender-body approximation, the problem of determining the axisymmetric response of the shape of the free surface of a cylindrical liquid column bounded by two solid regions is modeled by a one-dimensional system of nonlinear equations. It is found that the sensitivity of the zone shape depends on the static Bond number, BO, aspect ratio, and viscosity, as well as the amplitude and frequency of the disturbance. The general trend is an increase in tolerable residual gravity with increasing frequency. At the eigenfrequencies of the zone, however, there are dramatic deviations from this trend. At these frequencies the tolerable residual gravity level can be two orders of magnitude lower at this frequency.

Zhang, Yiqiang↗
NASA NTRS1990

CO2 lasers and applications II; Proceedings of the Third European Congress on Optics, The Hague, Netherlands, Mar. 12-14, 1990

Recent advances in CO2 laser technology and its applications are examined. Topics discussed include the excitation of CO2 lasers by microwave discharge, a compact RF-excited 12-kW CO2 laser, a robotic laser for three-dimensional cutting and welding, three-dimensional CO2-laser material processing with gantry machine systems, and a comparison of hollow metallic waveguides and optical fibers for transmitting CO2-laser radiation. Consideration is given to an aerodynamic window with a pump cavity and a supersonic jet, cutting and welding Al using a high-repetition-rate pulsed CO2 laser, speckle reduction in CO2 heterodyne laser radar systems, high-power-laser float-zone crystal growth, melt dynamics in surface processing with laser radiation, laser hardfacing, surface melting of AlSi10Mg with CO2 laser radiation, material processing with Cu-vapor lasers, light-induced flow at a metal surface, and absorption measurements in high-power CW CO2-laser processing of materials.

Opower, Hans↗
NASA NTRS1991

Axial forcing of an inviscid finite length fluid cylinder

Current interest in microgravity materials processing has focused attention upon the finite fluid column. This configuration is used in the modeling of float zones. In this paper the incompressible inviscid finite length fluid column is subjected to an axial, time-dependent disturbance. The response of the fluid system and the resulting interface location are determined via Laplace transform methods.

Lyell, M. J.↗
NASA NTRS1990

Development of a new generation of high-temperature composite materials

Intermetallic matrix composites proposed to meet advanced aeropropulsion requirements are discussed. The powder metallurgy fabrication process currently being used to produce these intermetallic matrix composites will be presented, as will properties of one such composite, SiC/Ti3Al+Nb. In addition, the direction of future research will be outlined, including plans for enhanced fabrication of intermetallic composites by the arc-spray technique and fiber development by the floating-zone process.

Brindley, P. K.↗
NASA NTRS1992

An examination of anticipated g-jitter on Space Station and its effects on materials processes

Information on anticipated g-jitter on Space Station Freedom and the effect of the jitter on materials processes is given in viewgraph form. It was concluded that g-jitter will dominate the acceleration environment; that it is a 3D multifrequency phenomenon; and that it varies dramatically in orientation. Information is given on calculated or measured sources of residual acceleration, aerodynamic drag, Shuttle acceleration measurements, the Space Station environment, tolerable g-levels as a function of frequency, directional solidification, vapor crystal growth, protein crystal growth, float zones, and liquid bridges.

Nelson, Emily↗
NASA NTRS1992

High temperature aircraft research furnace facilities

Focus is on the design, fabrication, and development of the High Temperature Aircraft Research Furnace Facilities (HTARFF). The HTARFF was developed to process electrically conductive materials with high melting points in a low gravity environment. The basic principle of operation is to accurately translate a high temperature arc-plasma gas front as it orbits around a cylindrical sample, thereby making it possible to precisely traverse the entire surface of a sample. The furnace utilizes the gas-tungsten-arc-welding (GTAW) process, also commonly referred to as Tungsten-Inert-Gas (TIG). The HTARFF was developed to further research efforts in the areas of directional solidification, float-zone processing, welding in a low-gravity environment, and segregation effects in metals. The furnace is intended for use aboard the NASA-JSC Reduced Gravity Program KC-135A Aircraft.

Smith, James E., Jr.↗
NASA NTRS1992

Canadian Space Agency Space Station Freedom utilization plans

Under the terms of the NASA/CSA Memorandum of Understanding, Canada will contribute the Mobile Servicing System and be entitled to use 3 percent of all Space Station utilization resources and user accommodations over the 30 year life of the Station. Equally importantly Canada, like NASA, can begin to exploit these benefits as soon as the Man-Tended Capability (MTC) phase begins, in early 1997. Canada has been preparing its scientific community to fully utilize the Space Station for the past five years; most specifically by encouraging, and providing funding, in the area of Materials Science and Applications, and in the area of Space Life Sciences. The goal has been to develop potential applications and an experienced and proficient Canadian community able to effectively utilize microgravity environment facilities such as Space Station Freedom. In addition, CSA is currently supporting four facilities; a Laser Test System, a Large Motion Isolation Mount, a Canadian Float Zone Furnace, and a Canadian Protein Crystallization Apparatus. In late April of this year CSA sent out a Solicitation of Interest (SOI) to potential Canadian user from universities, industry, and government. The intent of the SOI was to determine who was interested, and the type of payloads which the community at large intended to propose. The SOI will be followed by the release of an Announcement of Opportunity (AO) following governmental approval of the Long Term Space plan later this year, or early next year. Responses to the AO will be evaluated and prioritized in a fair and impartial payload selection process, within the guidelines set by our international partners and the Canadian Government. Payload selection is relatively simple compared to the development and qualification process. An end-to-end user support program is therefore also being defined. Much of this support will be provided at the new headquarters currently being built in St. Hubert, Quebec. It is recognized that utilizing the Space Station could be expensive for users; costing in many cases millions of dollars to get a payload from conception to retrieval. It is also recognized that some of the potential users cannot or will not invest a lot of money or effort into Space Station utilization, unless there is a perceived significant commercial potential. How best to fund Space Station payloads is under study. Space Station Freedom will provide the first opportunity for Canada to conduct experiments in a long-duration microgravity environment. CSA have been developing and funding potential users for some time, and considerable interest has been shown by the response to our SOI earlier this year. Canada can be one of the two earliest users for the Space Station, along with NASA. We hope to take full advantage of this opportunity.

Faulkner, James↗
NASA NTRS1993

On the shear stabilization of capillary break-up of finite liquid bridges

In this paper we consider an isothermal finite liquid bridge under zero-gravity. A sinusoidal interfacial shear stress drives a nonparallel flow in the bridge. The linear stability of this flow to three-dimensional disturbances (which may deform the cylindrical gas-liquid interface) is determined numerically by solving an elliptic eigenvalue problem. Previous results on shear stabilization of capillary break-up of axially unbounded cylindrical interfaces containing a parallel flow are hereby extended to a nonparallel flow. The turning flow regions influence the stability significantly. However, for the particular cases considered, a small area in parameter space remains where the capillary instability is suppressed through interfacial shear. Second, non-axisymmetric oscillatory instabilities are found which originate from an interaction of the interface deformation and the basic flow. These instabilities may be the isothermal limit of the oscillatory instabilities observed in float-zone crystal growth.

Dijkstra, Henk A.↗
NASA NTRS1993

Detailed analysis of Honeywell In-Space Accelerometer data - STS-32

The Honeywell In-Space Accelerometer (HISA) system collected data in the mid-deck area of the Shuttle Columbia during the flight of STS-32, January 1990. The resulting data were to be used to investigate the response of crystal microstructure to different types of residual acceleration. The HISA is designed to detect and record transient and oscillatory accelerations. The sampling and electronics package stored averaged accelerations over two sampling periods; two sampling rates were available: 1 Hz and 50 Hz. Analysis of the HISA data followed the CMMR Acceleration Data Processing Guide, considering in-house computer modelling of a float-zone indium crystal growth experiment. Characteristic examples of HISA data showing the response to the primary reaction control system, Orbiter Maneuvering System operations, and crew treadmill activity are presented. Various orbiter structural modes are excited by these and other activities.

Rogers, Melissa J. B.↗