Search NASA⌕ Search

SEARCH · Search NASA

Results for “force control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Position Control of Tendon-Driven Fingers

Conventionally, tendon-driven manipulators implement some force control scheme based on tension feedback. This feedback allows the system to ensure that the tendons are maintained taut with proper levels of tensioning at all times. Occasionally, whether it is due to the lack of tension feedback or the inability to implement sufficiently high stiffnesses, a position control scheme is needed. This work compares three position controllers for tendon-driven manipulators. A new controller is introduced that achieves the best overall performance with regards to speed, accuracy, and transient behavior. To compensate for the lack of tension feedback, the controller nominally maintains the internal tension on the tendons by implementing a two-tier architecture with a range-space constraint. These control laws are validated experimentally on the Robonaut-2 humanoid hand. I

Abdallah, Muhammad E.↗
NASA NTRS1990

Control of submersible vortex flows

Vortex flows produced by submersibles typically unfavorably influence key figures of merit such as acoustic and nonacoustic stealth, control effectiveness/maneuverability, and propulsor efficiency/body drag. Sources of such organized, primarily longitudinal, vorticity include the basic body (nose and sides) and appendages (both base/intersection and tip regions) such as the fairwater, dive planes, rear control surfaces, and propulsor stators/tips. Two fundamentally different vortex control approaches are available: (1) deintensification of the amplitude and/or organization of the vortex during its initiation process; and (2) downstream vortex disablement. Vortex control techniques applicable to the initiation region (deintensification approach) include transverse pressure gradient minimization via altered body cross section, appendage dillets, fillets, and sweep, and various appendage tip and spanload treatment along with the use of active controls to minimize control surface size and motions. Vortex disablement can be accomplished either via use of control vortices (which can also be used to steer the vortices off-board), direct unwinding, inducement of vortex bursting, or segmentation/tailoring for enhanced dissipation. Submersible-applicable vortex control technology is also included derived from various aeronautical applications such as mitigation of the wing wake vortex hazard and flight aircraft maneuverability at high angle of attack as well as the status of vortex effects upon, and mitigation of, nonlinear control forces on submersibles. Specific suggestions for submersible-applicable vortex control techniques are presented.

Bushnell, D. M.↗
NASA NTRS1976

Development of a fluidic rudder

Wind tunnel tests were performed to examine the concept of aircraft controls without moving parts, and aircraft stabilization by means of scoop-fed slots. Results of wind tunnel tests, in the framework of a NASA program, to determine the force-control characteristics of a symmetrical airfoil with scoop-fed slots are discussed. Further tests showed that a fluidic amplifier could be built into the airfoil and operate with ram air. A fluidic rudder was then developed, consisting of cascaded fluidic amplifiers necessary to couple low-level fluidic sensors with slot flow control of the aerodynamic force on the vertical tail.

Belsterling, C. A.↗
NASA NTRS1992

Dual-arm supervisory and shared control space servicing task experiments

A dual-arm task execution primitive has been implemented for cooperative dual-arm telerobotic task execution utilizing multiple sensors concurrently. The primitive has been integrated into a telerobot task execution system and can be called by a task planning system for execution of tasks requiring dual-arm sensor based motion, e.g., force control, teleoperation, and shared control. The primitive has a large input parameter set which is used to specify the desired behavior of the motion. Move-squeeze decomposition is utilized to decompose forces sensed at the wrists of the two manipulators into forces in the move subspace, which cause system motion, and forces in the squeeze subspaces, which cause internal forces. The move and squeeze forces are then separately controlled. Several space servicing tasks utilizing the cooperative dual-arm control capability are described, and experimental results from the tasks are given. The supervisory and shared control tasks include capture of a rotating satellite, orbital replacement unit changeout, fluid coupler seating and locking, and contour following.

Backes, Paul G.↗
NASA NTRS1991

Compact Force-Reflecting Hand Controller

Novel design keeps joints mechanically independent. Force-reflecting hand controller for remote manipulator offers two times work volume of any of its predecessors. Folded into volume half that of its immediate predecessor for storage. First six-degree-of-freedom, cable-driven controller designed with six revolute joints; contains no prismatic joints. Advantages of low friction, low inertia, and no backlash. Intended for use in telerobotic experiments during space flight, controller modified for such terrestrial applications as construction and handling of dangerous (e.g., hot, poisonous, radioactive, or infectious) materials.

Snow, Edward R.↗
NASA NTRS1990

Balancing Loads Among Robotic-Manipulator Arms

Paper presents rigorous mathematical approach to control of multiple robot arms simultaneously grasping one object. Mathematical development focuses on relationship between ability to control degrees of freedom of configuration and ability to control forces within grasped object and robot arms. Understanding of relationship leads to practical control schemes distributing load more equitably among all arms while grasping object with proper nondamaging forces.

Kreutz, Kenneth K.↗
NASA NTRS1974

Moonquake predetermination and tides

A pattern in moonquakes, which correlates with the monthly tidal cycle, also correlates with a phase-shifted pattern of a 7-month tidal cycle. The lead of approximately 2 months in moonquake occurrence can be explained if local tidal forces are combined with a moonquake-driving force. This force, assumed to result from the 6-yr physical libration in latitude, would cause N-S sliding of an outer layer across a solid layer within a decoupled core in a lunar model. During 1969-1971, the sliding would be southward with a progression of monthly maxima in the combined forces. Where these forces control moonquakes, the reversal in direction of the 6-year cyclic force in early 1972 should cause a minimum in moonquake activity. Decreases toward such a minimum did occur simultaneously in the similar progressions of monthly moonquakes and maxima in the combined forces at the most active hypocenter. Repetition of the 1966-1971 force pattern in 1975-1977 should produce a corresponding repetition of the moonquake pattern.

Chapman, W. B.↗
NASA NTRS1943

Effect of Fabric Deflection on Control Characteristics

In the past fabric-covered control surfaces have been widely used on airplanes without noticeable averse effects. On modern high-speed airplanes, however, several instances have been observed in which undesirable control force characteristics were attributed to deflection of the fabric on the control surfaces.

Phillips, W. H.↗
NASA NTRS1990

Feedback controlled electrostatic and electromagnetic sample positioners

Four different sample positioners are discussed. The four systems share a common operating principle in that the sample positioning is achieved by feedback controlled forces which can be electrostatic, dielectrophoretic, or electromagnetic. The first system is the electrostatic liquid drop positioner which operates at the near ambient position. The second system is the tetrahedral electrostatic positioner which is being developed for the high temperature materials processing in vacuum. The third system is essentially the the same tetrahedral system above except that the position control is achieved by dielectrophoretic forces in the pressurized gas environment. Finally, the feasibility of a feedback controlled electromagnetic positioner is discussed.

Rhim, Won-Kyu↗
NASA NTRS1960

Performance, Stability, and Control Investigation at Mach Numbers from 0.60 to 1.05 of a Model of the "Swallow" with Outer Wing Panels Swept 75 degree with and without Power Simulations

An investigation of the performance, stability, and control characteristics of a variable-sweep arrow-wing model with the outer wing panels swept 75 deg. has been conducted in the Langley 16-foot transonic tunnel. Four outboard engines located above and below the wing provided propulsive thrust, and, by deflecting in the pitch direction and rotating in the lateral plane, also produced control forces. The engine nacelles incorporated swept lateral and vertical fins for aerodynamic stability and control. Jet-off data were obtained with flow-through nacelles, simulating inlet flow; jet thrust and hot-jet interference effects were obtained with faired-nose nacelles housing hydrogen peroxide gas generators. Six-component force and moment data were obtained at Mach numbers from 0.60 to 1.05 through a range of angles of attack and angles of side-slip. Control characteristics were obtained by deflecting the nacelle-fin combinations as elevators, rudders, and ailerons at several fixed angles for each control. The results indicate that the basic wing-body configuration becomes neutrally stable or unstable at a lift coefficient of 0.15; addition of nacelles with fins delayed instability to a lift coefficient of 0.30. Addition of nacelles to the wing-body configuration increased minimum drag from 0.0058 to 0.0100 at a Mach number of 0.60 and from 0.0080 to 0.0190 at a Mach number of 1.05 with corresponding reductions in maximum lift-drag ratio of 12 percent and 33 percent, respectively. The nacelle-fin combinations were ineffective as longitudinal controls but were adequate as directional and lateral controls. The model with nacelles and fins was directionally and laterally stable; the stability generally increased with increasing lift. Jet interference effects on stability and control characteristics were small but the adverse effects on drag were greater than would be expected for isolated nacelles.

Schmeer, James W.↗
NASA NTRS1996

Minimum Surface-Effect Microgripper Design for Force-Reflective Telemanipulation of a Microscopic Environment

This paper describes the fundamental physical motivations for minimum surface effect design, and presents a microgripper that incorporates a piezoelectric ceramic actuator and a flexure-based structure and transmission. The microgripper serves effectively as a one degree-of-freedom prototype of minimum surface effect micromanipulator design. Data is presented that characterizes the microgripper performance under both pure position and pure force control, followed by a discussion of the attributes and limitations of flexure-based design. The microgripper is interfaced with a force-reflective macrogripper, and the pair controlled with a hybrid position/force scheme. Data is presented that illustrates the effective operation of the telerobotic pair.

Goldfarb, Michael↗
NASA NTRS1980

Active damping of modal vibrations by force apportioning

The theory and numerical simulation of active structural damping is described which requires few discrete control thrusters positioned on the structure. A particular apportioning of coherently phased control forces is applied for each vibration mode which is to be damped; this strongly affects the damped vibration mode, while minimally exciting all other modes. The force apportioning used is that which would tune a target mode if the structure was being shaken in a model vibration test. In contrast to model testing, the forces are varied temporally so as to dampen, rather than excite, the target mode(s).

Hallauer, W. L., Jr.↗
NASA NTRS1977

Analytical formulation of selected activities of the remote manipulator system

Existing analysis of Orbiter-RMS-Payload kinematics were surveyed, including equations dealing with the two body kinematics in the presence of a massless RMS and compares analytical explicit solutions with numerical solutions. For the following operational phases of the RMS numerical demonstration, problems are provided: (1) payload capture; (2) payload stowage and removal from cargo bay; and (3) payload deployment. The equation of motion provided accounted for RMS control forces and torque moments and could be extended to RMS flexibility and control loop simulation without increasing the degrees of freedom of the two body system.

K J Zimmerman↗
NASA NTRS1994

A genetic technique for planning a control sequence to navigate the state space with a quasi-minimum-cost output trajectory for a non-linear multi-dimnensional system

There are many multi-stage optimization problems that are not easily solved through any known direct method when the stages are coupled. For instance, we have investigated the problem of planning a vehicle's control sequence to negotiate obstacles and reach a goal in minimum time. The vehicle has a known mass, and the controlling forces have finite limits. We have developed a technique that finds admissible control trajectories which tend to minimize the vehicle's transit time through the obstacle field. The immediate applications is that of a space robot which must rapidly traverse around 2-or-3 dimensional structures via application of a rotating thruster or non-rotating on-off for such vehicles is located at the Marshall Space Flight Center in Huntsville Alabama. However, it appears that the development method is applicable to a general set of optimization problems in which the cost function and the multi-dimensional multi-state system can be any nonlinear functions, which are continuous in the operating regions. Other applications included the planning of optimal navigation pathways through a transversability graph; the planning of control input for under-water maneuvering vehicles which have complex control state-space relationships; the planning of control sequences for milling and manufacturing robots; the planning of control and trajectories for automated delivery vehicles; and the optimization and athletic training in slalom sports.

Hein, C.↗
NASA NTRS1996

Minimum surface-effect microgripper design for force-reflective telemanipulation of a microscopic environment

This paper describes the fundamental physical motivations for a minimum surface effect design, and presents a microgripper that incorporates a piezoelectric ceramic actuator and a flexure-based structure and transmission. The microgripper serves effectively as a one degree-of-freedom prototype of a minimum surface effect micromanipulator design. Data is presented that characterizes the microgripper performance under both pure position and pure force control, followed by a discussion of the attributes and limitations of flexure-based design. The microgripper is interfaced with a force reflective macrogripper, and the pair is controlled with a hybrid position/force scheme. Data is presented that illustrates the effective operation of the telerobotic pair.

Goldfarb, Michael↗
NASA NTRS1993

Remote Robot Control With High Force-Feedback Gain

Improved scheme for force-reflecting hand control of remote robotic manipulator provides unprecedently high force-reflection gain, even when dissimilar master and slave arms used. Three feedback loops contained in remote robot control system exerting position-error-based force feedback and compliance control. Outputs of force and torque sensors on robot not used directly for force reflection, but for compliance control, while errors in position used to generate reflected forces.

Kim, Won S.↗
NASA NTRS1993

A theoretical and experimental investigation of impact control for manipulators

This article describes a simple control strategy for stable hardon-hard contact of a manipulator with the environment. The strategy is motivated by recognition of the equivalence of proportional gain explicit force control and impedance control. It is shown that negative proportional force gains, or impedance mass ratios less than unity, can equivalently provide excellent impact response without bouncing. This result is indicated by an analysis performed with an experimentally determined arm/sensor/environment model. The results are corroborated by experimental data from implementation of the control algorithms on the CMU DD Arm II system. The results confirm that manipulator impact against a stiff environment without bouncing can be readily handled by this novel control strategy.

Volpe, Richard↗
NASA NTRS1981

Shape determination and control for large space structures

An integral operator approach is used to derive solutions to static shape determination and control problems associated with large space structures. Problem assumptions include a linear self-adjoint system model, observations and control forces at discrete points, and performance criteria for the comparison of estimates or control forms. Results are illustrated by simulations in the one dimensional case with a flexible beam model, and in the multidimensional case with a finite model of a large space antenna. Modal expansions for terms in the solution algorithms are presented, using modes from the static or associated dynamic mode. These expansions provide approximated solutions in the event that a used form analytical solution to the system boundary value problem is not available.

Weeks, C. J.↗