Results for “generative flow model” — Page 12

NASA NTRS1993

Computational analysis of hypersonic shock wave/wall jet interaction

The purpose of this study is to investigate the CFD code General Aerodynamic Simulation Program (GASP) for application to a specific scramjet combustor phenomenon, that of an adverse pressure gradient caused by an oblique shock wave impinging upon a wall cooling film. The basis of this investigation is data available from an existing experimental study, which includes wall pressure, wall heat transfer, and schlieren photographs. This experimental study was conducted at a nominal Mach number of 6.0 in the Calspan 48-inch shock tunnel. The particular case of interest generates flow separation at the shock impingement point. Two algebraic turbulence models, the Baldwin-Lomax model and the Goldberg model, are considered for this computational study. Resultant computational wall pressure and heat transfer for both turbulence models are compared with experimental data. The Goldberg turbulence model provides a more accurate prediction of the recirculation region, and as a result, a better comparison with the experimental data.

Mekkes, Gregory L.↗

NASA NTRS1996

Task 7: ADPAC User's Manual

The overall objective of this study was to develop a 3-D numerical analysis for compressor casing treatment flowfields. The current version of the computer code resulting from this study is referred to as ADPAC (Advanced Ducted Propfan Analysis Codes-Version 7). This report is intended to serve as a computer program user's manual for the ADPAC code developed under Tasks 6 and 7 of the NASA Contract. The ADPAC program is based on a flexible multiple- block grid discretization scheme permitting coupled 2-D/3-D mesh block solutions with application to a wide variety of geometries. Aerodynamic calculations are based on a four-stage Runge-Kutta time-marching finite volume solution technique with added numerical dissipation. Steady flow predictions are accelerated by a multigrid procedure. An iterative implicit algorithm is available for rapid time-dependent flow calculations, and an advanced two equation turbulence model is incorporated to predict complex turbulent flows. The consolidated code generated during this study is capable of executing in either a serial or parallel computing mode from a single source code. Numerous examples are given in the form of test cases to demonstrate the utility of this approach for predicting the aerodynamics of modem turbomachinery configurations.

Hall, E. J.↗

NASA NTRS2000

Validation and Development of the GPCP Experimental One-Degree Daily (1DD) Global Precipitation Product

The One-Degree Daily (1DD) precipitation dataset has been developed for the Global Precipitation Climatology Project (GPCP) and is currently in beta test preparatory to release as an official GPCP product. The 1DD provides a globally-complete, observation-only estimate of precipitation on a daily 1 deg. x 1 deg. grid for the period 1997 through early 2000 (by the time of the conference). In the latitude band 40N-40S the 1DD uses the Threshold-Matched Precipitation Index (TMPI), a GPI-like IR product with the pixel-level T(sub b) threshold and (single) conditional rain rate determined locally for each month by the frequency of precipitation in the GPROF SSM/I product and by, the precipitation amount in the GPCP monthly satellite-gauge (SG) combination. Outside 40N-40S the 1DD uses a scaled TOVS precipitation estimate that has month-by-month adjustments based on the TMPI and the SG. Early validation results are encouraging. The 1DD shows relatively large scatter about the daily validation values in individual grid boxes, as expected for a technique that depends on cloud-sensing schemes such as the TMPI and TOVS. On the other hand, the time series of 1DD shows good correlation with validation in individual boxes. For example, the 1997-1998 time series of 1DD and Oklahoma Mesonet values in a grid box in northeastern Oklahoma have the correlation coefficient = 0.73. Looking more carefully at these two time series, the number of raining days for the 1DD is within 7% of the Mesonet value, while the distribution of daily rain values is very similar. Other tests indicate that area- or time-averaging improve the error characteristics, making the data set highly attractive to users interested in stream flow, short-term regional climatology, and model comparisons. The second generation of the 1DD product is currently under development; it is designed to directly incorporate TRMM and other high-quality precipitation estimates. These data are generally sparse because they are observed by low-orbit satellites, so a fair amount of work must be devoted to analyzing the effect of data boundaries. This work is laying, the groundwork for effective use of the NASA Global Precipitation Mission, which will have full Global coverage by low-orbit passive microwave satellites every three hours.

Huffman, George J.↗

NASA NTRS2010

Space Borne and Ground-Based Observations of Transient Processes Occurring Around Substorm Onset

The combined THEMIS five spacecraft in-situ and ground magnetic and visible camera arrays have advanced considerably our understanding of the causal relationship between midtail plasma flows, transient ionospheric features, and ground magnetic signatures. In particular recent work has shown a connection between equatorward moving visible ionospheric transients and substorm onset, in both white-light and 6300 nm emissions. These observations, together with THEMIS in-situ measurements of bulk flows, provides strict constraints on the sequence of events leading to substorm auroral onset.We first provide a brief summary of these observations, highlighting in particular areas where the two observations differ, and suggest reasons for the differences. Next, by combining the observed correlation of flow and Pi2 waveform with a unified model of global Pi2 generation and substorm current wedge initiation we present a self-consistent description of the dynamical processes and communicative pathways that occur just prior to and during substorm expansion onset.

Kepko, L.↗

NASA NTRSDate not supplied

Assessment of HAB Particulate Tracing in EMU Helmet in Support of Eva 80

After water was reported in the EMU helmet during ISS US EVA-80, mitigation strategies were created to attempt to arrest the motion of any droplets that enter the helmet for future Extravehicular Activities (EVAs). This included adding absorbent materials into the interior of the helmet. But before a mitigation strategy can be implemented, it must first be proven to be safe. Towards this aim, a computational fluid dynamics (CFD) analysis was done tracing the paths of particulates potentially generated by the absorbent material. The objective was to characterize the risk these particulates pose for inspiration and eye irritation by tracking what percentage of particulates contact the suit-wearer’s face, eyes, or mouth. The model consisted of a human mannikin head and torso inside the EMU suit and helmet. The software used was ANSYS Fluent, with discrete phase modeling enabled to generate and track the particulates within the ventilation flow of the helmet.

Abigail Rose Baukus↗

NASA NTRSDate not supplied

Assessment of HAB Particulate Tracing in EMU Helmet in Support of Eva 80

After water was reported in the EMU helmet during ISS US EVA-80, mitigation strategies were created to attempt to arrest the motion of any droplets that enter the helmet for future Extravehicular Activities (EVAs). This included adding absorbent materials into the interior of the helmet. But before a mitigation strategy can be implemented, it must first be proven to be safe. Towards this aim, a computational fluid dynamics (CFD) analysis was done tracing the paths of particulates potentially generated by the absorbent material. The objective was to characterize the risk these particulates pose for inspiration and eye irritation by tracking what percentage of particulates contact the suit-wearer’s face, eyes, or mouth. The model consisted of a human mannikin head and torso inside the EMU suit and helmet. The software used was ANSYS Fluent, with discrete phase modeling enabled to generate and track the particulates within the ventilation flow of the helmet.

Abigail Baukus↗

NASA NTRSDate not supplied

Assessment of HAB Particulate Tracing in EMU Helmet in Support of Eva 80

After water was reported in the EMU helmet during ISS US EVA-80, mitigation strategies were created to attempt to arrest the motion of any droplets that enter the helmet for future Extravehicular Activities (EVAs). This included adding absorbent materials into the interior of the helmet. But before a mitigation strategy can be implemented, it must first be proven to be safe. Towards this aim, a computational fluid dynamics (CFD) analysis was done tracing the paths of particulates potentially generated by the absorbent material. The objective was to characterize the risk these particulates pose for inspiration and eye irritation by tracking what percentage of particulates contact the suit-wearer’s face, eyes, or mouth. The model consisted of a human mannikin head and torso inside the EMU suit and helmet. The software used was ANSYS Fluent, with discrete phase modeling enabled to generate and track the particulates within the ventilation flow of the helmet.

Abigail Baukus↗

NASA NTRSDate not supplied

Comparing Unstructured Adaptive Mesh Solutions for the High Lift Common Research Model Airfoil

Discretization error is a common source of uncertainty in Computational Fluid Dynamics (CFD) analyses. Traditional means of controlling discretization error through fixed-mesh refinement studies has proven to be difficult particularly when modeling complex geometries and flow fields. One reason for this is that mesh generation in today’s production CFD workflow is often a labor intensive process that is heavily dependent on user judgment. Unstructured mesh adaptation is known to be an efficient way to control discretization errors in CFD. Adaptive methods replace user based decision making with automated processes that optimize a mesh to reduce discretization error. This paper compares the application of multiple solution adaptive techniques in combination with multiple flow solvers to solve for the flow field about a 2D airfoil section of the NASA High-Lift Common Research Model (HL-CRM). By driving the adaptive mesh processes to a similar level of mesh convergence, the ability to achieve consistent results between multiple adaptive techniques and flow solvers is demonstrated. Mesh convergence for the various adaptive mesh approaches is compared identifying potential areas for improvement and providing mesh generation guidance for future workshops.

mesh adaptation high-lift 2D airfoil↗

NASA NTRSDate not supplied

Comparing Unstructured Adaptive Mesh Solutions for the High Lift Common Research Model Airfoil

Discretization error is a common source of uncertainty in Computational Fluid Dynamics (CFD) analyses. Traditional means of controlling discretization error through fixed-mesh refinement studies has proven to be difficult particularly when modeling complex geometries and flow fields. One reason for this is that mesh generation in today’s production CFD workflow is often a labor intensive process that is heavily dependent on user judgment. Unstructured mesh adaptation is known to be an efficient way to control discretization errors in CFD. Adaptive methods replace user based decision making with automated processes that optimize a mesh to reduce discretization error. This paper compares the application of multiple solution adaptive techniques in combination with multiple flow solvers to solve for the flow field about a 2D airfoil section of the NASA High-Lift Common Research Model (HL-CRM). By driving the adaptive mesh processes to a similar level of mesh convergence, the ability to achieve consistent results between multiple adaptive techniques and flow solvers is demonstrated. Mesh convergence for the various adaptive mesh approaches is compared identifying potential areas for improvement and providing mesh generation guidance for future workshops.

mesh adaptation↗

NASA NTRS2001

Augmentation of Stagnation Region Heat Transfer Due to Turbulence from a DLN Can Combustor

Heat transfer measurements have been made in the stagnation region of a flat plate with a circular leading edge. Electrically heated aluminum strips placed symmetrically about the leading edge stagnation region were used to measure spanwise-averaged heat transfer coefficients. The maximum Reynolds number obtained, based on leading edge diameter, was about 100,000. The model was immersed in the flow field downstream of an approximately half-scale model of a can-type combustor from a low NO(x), ground-based power-generating turbine. The tests were conducted with room temperature air; no fuel was added. Room air flowed into the combustor through six vane-type fuel/air swirlers. The combustor can contained no dilution holes. The fuel/air swirlers all swirled the incoming airflow in a counterclockwise direction (facing downstream). A five-hole probe flow field survey in the plane of the model stagnation point showed the flow was one big vortex with flow angles up to 36 deg at the outer edges of the rectangular test section. Hot-wire measurements showed test section flow had very high levels of turbulence, around 28.5%, and had a relatively large axial-length scale-to-leading edge diameter ratio of 0.5. X-wire measurements showed the turbulence to be nearly isotropic. Stagnation heat transfer augmentation over laminar levels was around 77% and was about 14% higher than predicted by a previously developed correlation for isotropic grid-generated turbulence.

VanFossen, G. James↗

NASA NTRS1975

A study of sound generation in subsonic rotors, volume 2

Computer programs were developed for use in the analysis of sound generation by subsonic rotors. Program AIRFOIL computes the spectrum of radiated sound from a single airfoil immersed in a laminar flow field. Program ROTOR extends this to a rotating frame, and provides a model for sound generation in subsonic rotors. The program also computes tone sound generation due to steady state forces on the blades. Program TONE uses a moving source analysis to generate a time series for an array of forces moving in a circular path. The resultant time series are than Fourier transformed to render the results in spectral form. Program SDATA is a standard time series analysis package. It reads in two discrete time series and forms auto and cross covariances and normalizes these to form correlations. The program then transforms the covariances to yield auto and cross power spectra by means of a Fourier transformation.

Chalupnik, J. D.↗

NASA NTRS1994

Differential rotation and turbulent convection: A new Reynolds stress model and comparison with solar data

In most hydrodynamic cases, the existence of a turbulent flow superimposed on a mean flow is caused by a shear instability in the latter. Boussinesq suggested the first model for the turbulent Reynolds stresses bar-(u(sub i)u(sub j)) in which the mean shear S(sub ij) is the cause (or source) of turbulence represented by the stress bar-(u(sub i)u(sub j)). In the case of solar differential rotation, exactly the reverse physical process occurs: turbulence (which must pre-exist) generates a mean flow which manifests itself in the form of differential rotation. Thus, the Boussinesq model is wholly inadequate because in the solar case, cause and effect are reversed. Since the Boussinesq model is inadequate, one needs an alternative model for the Reynolds stresses. We present a new dynamical model for the Reynolds stresses, convective fluxes, turbulent kinetic energy, and temperature fluctuations. The complete model requires the solution of 11 differential equations. We then introduce a set of simplifying assumptions which reduce the full dynamical model to a set of algebraic Reynolds stress models. We explicitly solve one of these models that entails only one differential equation. The overall agreement with the data is obtained with a model that is neither phenomenological nor one that requires a full numerical simulation, since it is algebraic in nature. The new model can play an important role in understanding the complex physics underlying the interplay between solar differential rotation and convection, as many physical processes can naturally be incorporated into the model.

Canuto, V. M.↗

NASA NTRS2023

Turbulence Model Validation Through Joint Experimental /Computational Studies of Separated Flow Over A Three-Dimensional Tapered Bump: Part I - Experimental Investigation

The results of a three-year experimental campaign aimed at comprehensively documenting the separated flow over a three-dimensional bump are presented with the purpose of generating a benchmark experimental database useful in validating computational fluid dynamics (CFD) flow simulations. The bump model geometry was designed to provide well-defined and repeatable smooth-body flow separation conditions that were suitable for both experiments and simulations. The bump had a Gaussian streamwise profile with a constant height equal to 8.5% of its width over the central 60% of the test section width. The remaining 40% were outboard spanwise portions that gradually taper to zero using an error function profile to minimize side-wall boundary layer effects. The model was immersed in a turbulent boundary layer that was developed on a suspended flat plate in the Notre Dame Mach 0.6 Wind Tunnel. In order to document the effect of the incoming boundary layer thickness on the flow separation, the bump model could be located at two streamwise positions. The mean velocity and turbulence intensity of the wind tunnel freestream flow field and approaching turbulent boundary layer were fully documented. The measurements of the flow separation region included surface visualization, wall shear stress using oil-film interferometry, mean and dynamic surface pressure, and planar and stereoscopic particle image velocimetry. The experiments were conducted over a range of Mach numbers from 0.05 to 0.2 corresponding to a range of Reynolds numbers based on the test section spanwise dimension (0.914m) of 1.0 × 10 6 ≤ Re L = U ∞ L/ν ≤ 4.0 × 10 6 . The bulk of the results are presented for the higher Mach number conditions of 0.1 and 0.2 with Re L = 2.0 × 10 6 and 4.0 × 10 6 , respectively. Extensive uncertainty analysis of the data was performed. The data is archived in the NASA Langley Turbulence Modeling Resource website at https://turbmodels.larc.nasa.gov/Other_exp_Data/speedbump_sep_exp.html. In addition to the experiments, a computational effort was made in parallel by the CFD group at Boeing Research & Technology highlighting the usefulness of the data set, which is outlined in the accompanying CFD report.

Flow separation↗

NASA NTRS1981

Crossflow effects on steady and fluctuating pressures on an ogive-cylinder cone-frustum model in supersonic separated flow

Wind-tunnel tests were conducted on an ogive-cylinder model with two axisymmetric protuberances having cone frustum angles of cone = 23 deg and 45 deg that were used to generate detached shock waves and the resulting separated flow areas downstream of the shock. The tests were conducted in a 9 by 7 foot supersonic wind tunnel at a free-stream Mach number of 2.0 and at Reynolds numbers of 1.5 x 1 million and 3.9 x 1 million, based on body diameter. The model had an afterbody fineness ratio of 8.3, and the ogive nose had a fineness ratio of 3.0. Two characteristics of the fluctuating pressures in surface vortex flows that result from the crossflow component, (velocity along the tunnel longitudinal axis free stream angle of attack), in combination with changes in the longitudinal pressure gradient were measured: (1) the broadband, rms-pressure coefficients and (2) the power spectral densities. Measurements are presented for various flow regions on the model such as the attached turbulent boundary layer, the detached frustum shock wave, and separated flow areas. The results indicate that the pressure fluctuations around or in the neighborhood of the foci of the vortex flows had broadband intensities and power spectral densities nearly identical to the levels previously measured in separated-flow regions at angles of attack of 0 deg.

Dods, J. B., Jr.↗

NASA NTRS1994

Numerical Generation of Asymmetric Flows about Slender Bodies of Revolution at Extreme Incidence

It is well known that slender bodies of revolution will develop an asymmetric, unsteady flow pattern in experimental tests, if the angle of incidence to the oncoming stream is above a critical value. It has been suggested that the origin of these asymmetric flows may stem from geometric imperfections of the model being tested, or from disturbances in the oncoming stream. In numerical simulations, it is possible to generate bodies of revolution which are perfectly symmetric about their longitudinal axis, and to impose uniform flow conditions which are free from disturbances. The current work presents numerical simulations of the flow about an ogive-cylinder configuration at 40 and 60 degree angle of incidence. These simulations. were performed using numerical algorithms which are also symmetric about the lateral plane of the cylinder body. The flowfields at 40 degree angle of attack were seen to remain symmetric to the round-off accuracy of the computer. At 60 degree angle of attack, a lateral force coefficient developed of O(1) which progressed to an alternate vortex shedding in time. The nature of this lateral force generation and vortex shedding was dependent on the choice of numerical algorithm. The origin of the asymmetries observed in the 60 degree angle of attack computations were traced to round-off errors in the implicit block-matrix inverter. A means of inverting the implicit operator matrices, which maintains the symmetry of the overall numerical algorithm was implemented.

Murman, Scott M.↗

NASA NTRS1988

Incompressible and anelastic flow simulations on numerically generated grids

In the numerical simulation of incompressible and anelastic flows, it is necessary to solve an elliptic equation at each time step. When the boundaries of such flows are nonrectangular, it may be advantageous to solve the equations on a new, numerically generated coordinate grid, in which the property of orthogonality has been preserved. Flow equations in general curvilinear coordinates maintaining the conservative form are given for both anelastic models using the momentum equations, and for incompressible models, using the vorticity equation. The general problem of grid-generation in two dimensions is presented, and a quasi-conformal transformation technique is discussed in detail. Some examples of grids generated by this technique are exhibited. Three examples of the flow of a stratified fluid over obstacles are presented, in which the grid-generation permits some new results to be obtained.

Sharman, R. D.↗

NASA NTRS2016

Feasibility of Varying Geo-Fence Around an Unmanned Aircraft Operation Based on Vehicle Performance and Wind

Managing trajectory separation is critical to ensuring accessibility, efficiency, and safety in the unmanned airspace. The notion of geo-fences is an emerging concept, where distance buffers enclose individual trajectories and areas of operation in order to manage the airspace. Currently, the Air Traffic Management system for commercial travel defines static distance buffers around the aircraft; however, commercial UASs are envisioned to operate in significantly closer proximity to other UAS requiring a geo-fence for spacing operations. The geo-fence size can be determined based on vehicle performance characteristics, state of the airspace, weather, and other unforeseen events such as emergency or disaster response. Calculation of the geo-fence size could be determined as part of pre-flight planning and during real-time operations. A largely non-homogeneous fleet of UASs will be operating in low altitude and will likely be commercially developed. Due to intellectual property concerns, the operators may not provide detailed specifications of the control system to UTM. In addition, the huge variety of UAS makes modeling each control system prohibitive and flight data for these vehicles may not exist. Therefore, a generalized, simple geo-fence sizing algorithm must be developed such that it does not rely on detailed knowledge of the vehicle control system, accounts for the presence of urban winds, and is sufficiently accurate. In this work, two simple models are investigated to determine its feasibility as an adequate means for calculating the geo-fence size. The vehicle data used in this work are provided by UAS manufactures who have partnered with NASA's UTM project and some publicly available websites. The first model utilizes wind data processed from the NOAA HRRR (Hourly Rapid Refresh) product and Sonar Annemometer data provided by San Jose State. The second model utilizes OpenFOAM which is a CFD code used to generate a wind field for flow around a single building. The key vehicle performance parameters can include UAS response time to disturbances, command to actuation latency, control system rate limits, time to recovery to desired path, and aerodynamics. It was found that the first model provides an initial understanding of geo-fence sizing, but does not provide enough accuracy to provide UTM with an efficient means of scheduling vehicles. The results of the second model reveal that modeling UAS controls systems with a linearized plant and gain scheduled PID controller does not allow capture the UAS flight dynamics within a significant envelope of the wind disturbances.

uncertainty↗

NASA NTRSDate not supplied

Modeling Shock-Separated Flow with the Active Model Split

The predictive accuracy of typical hybrid RANS/LES models is limited by several shortcomings, such as modeled-stress depletion and a dependence on scalar grid measures. The "active model-split" (AMS) hybrid RANS/LES model was developed by Haering, Oliver, and Moser to address these shortcomings. In this model, the mean and fluctuating portions of the stress are modeled separately; this allows for a consistent treatment of the mean flow even in the presence of resolved fluctuations. Part of this hybrid model is an active forcing, which generates turbulent fluctuations in regions that support LES-type fluctuations. In this presentation, some recent results are shown using the active model-split for shock-separated flows. The effects of the active forcing are examined, including the effects on anisotropy and acoustics. Superior predictive accuracy over RANS is shown for some quantities of interest, such as the shock location.

RANS↗