Search NASA⌕ Search

SEARCH · Search NASA

Results for “heating and current drive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Pathways towards break even for low convergence ratio direct-drive inertial confinement fusion

Following indirect-drive experiments which demonstrated promising performance for low convergence ratios (below 17), previous direct-drive simulations identified a fusion-relevant regime which is expected to be robust to hydrodynamic instability growth. This paper expands these results with simulated implosions at lower energies of 100 and 270 kJ, and ‘hydrodynamic equivalent’ capsules which demonstrate comparable convergence ratio, implosion velocity and in-flight aspect ratio without the need for cryogenic cooling, which would allow the assumptions of one-dimensional-like performance to be tested on current facilities. A range of techniques to improve performance within this regime are then investigated, including the use of two-colour and deep ultraviolet laser pulses. Finally, further simulations demonstrate that the deposition of electron energy into the hotspot of a low convergence ratio implosion through auxiliary heating also leads to significant increases in yield. Results include break even for 1.1 MJ of total energy input (including an estimated 370 kJ of short-pulse laser energy to produce electron beams for the auxiliary heating), but are found to be highly dependent upon the efficiency with which electron beams can be created and transported to the hotspot to drive the heating mechanism.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2011

Preparation and Testing of Ice-Enriched Lunar Regolith Simulant for RESOLVE OVEN

The RESOLVE (Regolith and Environment Science and Oxygen and Lunar Volatile Extraction) project seeks to deploy a robotic ISRU lander at the lunar south pole to determine the accessibility of frozen ice and the resource potential at various locations. The OVEN (Oxygen and Volatiles Extraction Node) component will be used to heat samples to 150 C or higher in order to drive off ice and other volatiles, which will then be identified and measured. An ice volatilization system has been developed to specifically collect data on the extraction of water vapor from a sample. Testing of the system was begun in April of this year. This report addresses our current work to test the system in a relevant environment in this case, using simulants with up to 10wt% water ice at 76K, in reduced atmosphere.

Cooper, Bonnie↗
NASA NTRS2012

Optimal Force Control of Vibro-Impact Systems for Autonomous Drilling Applications

The need to maintain optimal energy efficiency is critical during the drilling operations performed on future and current planetary rover missions (see figure). Specifically, this innovation seeks to solve the following problem. Given a spring-loaded percussive drill driven by a voice-coil motor, one needs to determine the optimal input voltage waveform (periodic function) and the optimal hammering period that minimizes the dissipated energy, while ensuring that the hammer-to-rock impacts are made with sufficient (user-defined) impact velocity (or impact energy). To solve this problem, it was first observed that when voice-coil-actuated percussive drills are driven at high power, it is of paramount importance to ensure that the electrical current of the device remains in phase with the velocity of the hammer. Otherwise, negative work is performed and the drill experiences a loss of performance (i.e., reduced impact energy) and an increase in Joule heating (i.e., reduction in energy efficiency). This observation has motivated many drilling products to incorporate the standard bang-bang control approach for driving their percussive drills. However, the bang-bang control approach is significantly less efficient than the optimal energy-efficient control approach solved herein. To obtain this solution, the standard tools of classical optimal control theory were applied. It is worth noting that these tools inherently require the solution of a two-point boundary value problem (TPBVP), i.e., a system of differential equations where half the equations have unknown boundary conditions. Typically, the TPBVP is impossible to solve analytically for high-dimensional dynamic systems. However, for the case of the spring-loaded vibro-impactor, this approach yields the exact optimal control solution as the sum of four analytic functions whose coefficients are determined using a simple, easy-to-implement algorithm. Once the optimal control waveform is determined, it can be used optimally in the context of both open-loop and closed-loop control modes (using standard realtime control hardware).

Aldrich, Jack B.↗
DOE OSTI2025

Effect of self-generated magnetic fields on x-ray emission in Kr-filled targets at the National Ignition Facility

We examine the effects of self-generated magnetic fields in a Kr gas pipe x-ray source platform. X-ray emission from Kr plasma is dependent on the plasma conditions, as the ionization state is largely a function of temperature. Magnetic fields are known to limit heat conduction, which increases temperature. We show that the emission in simulations of the gas pipe x-ray source is dependent on how self-generated magnetic fields are modeled. The inclusion of self-generated magnetic fields in simulations more accurately captures the emission of lower energy x-ray emission (L-shell), bringing results closer to experiments. The modeled x-ray emission and self-generated magnetic fields are shown to be particularly sensitive to the inclusion of the Nernst effect in simulations. Severely limiting the Nernst effect leads to a hotter Kr plasma, which can account for the discrepancy seen in earlier studies. By modifying the Nernst effect multiplier, we can achieve better experimental agreement in x-ray emission from gas pipes; the value of the multiplier that leads to the best agreement is dependent on the laser power of the drive. Currently, the suppression factor of the Nernst effect needed for high power drives (PL>200 TW) is more restrictive than what is currently put forward by non-local models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Geomechanical in situ testing of fault reactivation in argillite repositories

Abstract. Pressurization of natural faults as a result of repository-induced effects can lead to their reactivation and permeability generation in case such features are present near disposal tunnels. Potential driving forces for such pressurization are the temperature increase caused by heat-producing high-level radioactive waste and the generation of hydrogen and other gases due to corrosion of engineered materials. We are primarily concerned about pressurization and fault activation in host rocks and faults that have very low natural permeability for pore pressure increases to dissipate, such as the argillite rocks currently investigated in Switzerland, France and other countries. This presentation discusses a series of in situ experiments of fault activation by fluid injection conducted in the argillite rock (Opalinus clay) at the Mont Terri underground research laboratory in Switzerland. A multi-model monitoring test bed was installed at Mont Terri that includes distributed fiber optics for strain, temperature, and acoustics; local fault pore pressure and three-dimensional displacement sensors; active seismic imaging; and passive seismic monitoring. The fault experiments (and their subsequent analysis via hydromechanical modeling) provide a new fundamental understanding of the coupling between pore pressure, fault deformation and permeability generation as a function of time and allow exploring how seismic and aseismic events may impact the integrity of faulted argillite host rock. Our experimental observations demonstrate that significant flow (and transport) can occur along the initially impermeable argillite fault when rupture is activated. However, the fault permeability decreases to almost its pre-activation value when fluid injection ceases and fluid pressure drops. Dilatant slip on the fault plane alone does not explain the observed increase in fault permeability; pressure-induced fault opening also plays a role, favored by the softness of the shale along with the fact that the structure of the fault zone prevents fluids from diffusing into the adjacent damage zone. Rupture initiation and permeability generation is initially aseismic, associated only with an increase in noise level and emerging tremors. Micro-earthquakes are initiated later in the experiments and typically occur away from the fluid-pressurized area. Hydromechanical models show that stress transferred from the initial aseismic deformation can build up to stress criticality and later induce seismic rupture. After presenting the experimental results, we will close the presentation with an outlook to future experimental campaigns using the fault test bed at Mont Terri. We are currently planning a controlled thermal stimulation of the fault, where instead of fluid injection as a trigger mechanism we will heat up the nearby rock volume and measure potential effects on fault stability. Lessons learned from our past and future experiments will help inform the safety assessment of geologic disposal in argillite host rock.

Birkholzer, Jens T.↗
DOE OSTI2023

A novel Doppler backscattering (DBS) system to simultaneously measure radio frequency plasma fluctuations and low frequency turbulence

A novel quadrature Doppler Backscattering (DBS) system has been developed and optimized for the E-band (60–90 GHz) frequency range using either O-mode or X-mode polarization in DIII-D plasmas. In general, DBS measures the amplitude of density fluctuations and their velocity in the lab frame. The system can simultaneously monitor both low-frequency turbulence (f < 10 MHz) and radiofrequency plasma density fluctuations over a selectable frequency range (20–500 MHz). Detection of high-frequency fluctuations has been demonstrated for low harmonics of the ion cyclotron frequency (e.g., 2f ci ~ 23 MHz) and externally driven high-frequency helicon waves (f = 476 MHz) using an adjustable frequency down conversion system. Importantly, this extends the application of DBS to a high-frequency spectral domain while maintaining important turbulence and flow measurement capabilities. This unique system has low phase noise, good temporal resolution (sub-millisecond), and excellent wavenumber coverage (k θ ~ 1–20 cm –1 and kr ≲ 30 cm –1 ). As a demonstration, localized internal DIII-D plasma measurements are presented from turbulence (f ≤ 5 MHz), Alfvenic waves (f ~ 6.5 MHz), ion cyclotron waves (f ≥ 20 MHz), as well as fluctuations around 476 MHz driven by an external high-power 476 MHz helicon wave antenna. In the future, helicon measurements will be used to validate GENRAY and AORSA modeling tools for prediction of helicon wave propagation, absorption, and current drive location for the newly installed helicon current drive system on DIII-D.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Near-edge beta induced Alfven eigenmode in DIII-D high bootstrap current fraction plasmas

In DIII-D high bootstrap current fraction plasmas heated solely by neutral beam injection, a fast ion-driven Beta-Induced Alfven Eigenmode (BAE) is frequently observed. The BAE peaks near the edge, suggesting the possibility of enhanced fast ion transport there and raising a potential concern for the first wall. Theoretical analysis and simulations show that the mode location is not fully determined by the fast-ion drive intensity, i.e. fast ion pressure gradient but is strongly related to the background unfavorable magnetic curvature drive near the edge, which is an intrinsic property of advanced scenarios that rely on a large radius internal transport barrier that exists for all the kinetic channels for performance improvement.

beta induced Alfven eigenmode↗
DOE OSTI2024

A Hybrid Heavy Duty Diesel Power System for Off-Road Applications—Concept Validation

A multiyear power system R&D program was completed with the objective of developing an off-road hybrid heavy duty diesel engine with front end accessory drive-integrated energy storage. This system was validated to deliver 10.5–25.6% reduction in fuel consumption over current Tier 4 Final-based 18L diesel engines, over various off-road machine application cycles. The power system consisted of a downsized heavy-duty diesel 13L engine containing advanced combustion technologies, capable of elevated peak cylinder pressures and thermal efficiencies, thermal barrier coatings, exhaust waste heat recovery via SuperTurbo™ turbocompounding, and hybrid energy assisting and recovery through both mechanical and electrical systems. Following the concept definition, design, and analysis phases of the program, the final phase focused on building and validating the performance and efficiency in laboratory tests. While aspects of the system such as start/stop and reduced off-road cooling package energy losses were only analytically evaluated, the main 13L concept engine with full hybrid system was successfully built and tested in steady-state and in transient certification and real-world application cycles. Extensive simulations in Caterpillar's DYNASTY™ software environment utilized the validation test data to assess performance more fully and confidently over varied cycles and strategies. An average fuel consumption reduction of 17.9% was realized, and the majority (~13%) of the benefit stemmed from the core concept 13L engine. In conclusion, a total cost of ownership analysis provides context to commercial viability and where adoption focus should be placed.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Ion-temperature- and density-gradient-driven instabilities and turbulence in Wendelstein 7-X close to the stability threshold

Electrostatic gyrokinetic instabilities and turbulence in the Wendelstein 7-X stellarator are studied. Particular attention is paid to the ion-temperature-gradient (ITG) instability and its character close to marginal stability [Floquet-type turbulence (Zocco et al., Phys. Rev. E, vol. 106, 2022, p. L013202) with no electron temperature gradient]. The flux tube version of the δƒ code stella (Barnes et al., J. Comput. Phys., vol. 391, 2019, pp. 365–380) is used to run linear and nonlinear gyrokinetic simulations with kinetic electrons. The nature of the dominant instability depends on the wavelength perpendicular to the magnetic field, and the results are conveniently displayed in stability diagrams that take this dependence into account. This approach highlights the presence of universal instabilities, which are less unstable but have longer wavelengths than other modes. A quasi-linear estimate of the heat flux suggests they are relevant for transport. Close to the stability threshold, the linear eigenmodes and turbulence form highly extended structures along the computational domain if the magnetic shear is small. Numerical experiments and diagnostics are undertaken to assess the resulting radial localisation of the turbulence, which affects the interaction of the latter with zonal flows. Increasing the amplitude of the magnetic shear (e.g.through current drive) has a stabilising effect on the turbulence and, thus, reduces the nonlinear energy transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Demonstration of low-density, high-performance operation of sustained spheromaks and favorable scalability toward compact, low-cost fusion power plants (Final Scientific/Technical Report)

This project worked to advance the technical viability of a novel method for efficiently sustaining stable, high-performance spheromak plasma configurations to serve as the basis of compact, low-cost fusion power plants. In particular, our group worked to improve the method of Steady Inductive Helicity Injection (SIHI) with Imposed-Dynamo Current Drive (IDCD) for spheromak plasma sustainment. Prior to this project demonstrations of this plasma sustainment technology have achieved plasma performance consistent with entry milestone 3 of the BETHE FOA. Research and development (R&D) activities for this project were focused on increasing plasma performance toward a level consistent with exit milestone 4. To do this the PI and his group worked to increase the performance of sustained spheromaks produced in an existing experimental prototype (HIT-SIU) while improving confidence in projections to and design of future, higher performance devices through three primary R&D activities: 1) Improved control over the density of plasma in the device throughout a discharge to provide a pathway for demonstration of spheromaks Ohmically heating to the Mercier beta limit via: a. Fueling the device directly with plasma through the installation of pre-ionized source on the injectors b. Optimization of electrical current waveforms in the driver circuits to enable low-density plasma formation with a lower fueling rate 2) Computational demonstration of a validated, realistic injector circuit coupled to a dynamic plasma model capable of use as a design tool for SIHI drivers and associated circuits for new experimental design points on the pathway to commercial reactors. The improvements in plasma performance achieved during research activity 1), and the computational projections performed in research activity 2) increased the technological readiness level (TRL) of this fusion energy concept toward a level sufficient to attract early-stage private investment and/or other forms of follow-on investment to pursue required R&D activities required for the eventual fusion power plants based on this novel technical approach.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Materials Design Directions for Solar Thermochemical Water Splitting

The sustainable, economical production of molecular hydrogen is a crucial component of a net zero-greenhouse-gas-emissions future. Solar thermochemical water splitting (STWS) offers a renewable route to hydrogen with the potential to help decarbonize several industries, including transportation, manufacturing, mining, metals processing, and electricity generation, as well as provide sustainable hydrogen as a chemical feedstock. STWS uses high temperatures generated from concentrated sunlight or other sustainable means for high-temperature heat to produce hydrogen and oxygen from steam. For example, in its simplest form of a two-step thermochemical cycle, a redox-active metal oxide is heated to ≈1700-2000 K, driving off molecular oxygen while producing oxygen vacancies in the material. The reduced metal oxide then cools (ideally with the extracted heat recuperated for re-use) and, in a separate step, comes into contact with steam, which reacts with oxygen vacancies to produce molecular hydrogen while recovering the original state of the metal oxide. Despite its promising use of the entire solar spectrum to split water thermochemically, the current estimated cost of hydrogen produced via STWS is ≈4-6× the U.S. Department of Energy (DOE) Hydrogen Shot target value of $1/kg. One contributing approach to bridging this cost gap is the design of new materials with improved thermodynamic properties to enable higher efficiencies. The state-of-the-art (SOA) redox-active metal oxide for STWS is ceria (CeO 2 ), due to its close to optimal, although too high, oxygen vacancy formation enthalpy and large configurational and electronic entropy of reduction. However, ceria requires high operating temperatures and its efficiency is insufficient. Therefore, efforts to increase the efficiency of STWS cycles have focused on further optimizing oxygen vacancy formation enthalpies and augmenting the reduction entropy via substitution or doping and materials discovery schemes. Examples of the latter include the perovskites BaCe 0.25 Mn 0.75 O 3 and (Ca,Ce)(Ti,Mn)O 3 . These efforts and others have revealed intuitive chemical principles for the efficient and systematic design of more effective materials, such as the strong correlation between the enthalpies of crystal bond dissociation and solid-state cation reduction with the enthalpy of oxygen vacancy formation, as well as configurational entropy augmentation via the coexistence of two or more redox-active cation sublattices. The purpose of this chapter is to prepare the reader with an up-to-date account of STWS redox-active materials, both the SOA and promising newcomers, as well as to provide chemically intuitive strategies for improving their cycle efficiencies through materials design – in conjunction with ongoing efforts in reactor engineering and gas separations – to reach the cost points for commercial viability. First, we will introduce the thermodynamics of STWS using a two-step, metal-oxide, thermochemical cycle with economics in mind. We also will compare the pros and cons of processes that do or do not involve phase changes. Second, we will describe the qualities that make ceria the SOA STWS redox-active material, as well as its limitations. Third, we will survey some of the most promising candidates to date in the search for materials to supplant ceria, emphasizing the post-ternary, metal-oxide-perovskite alloys. Lastly, we will enumerate and discuss the following materials design directions for STWS redox-active materials: crystal reduction potentials as a proxy for oxygen vacancy formation enthalpies, engineering the electronic and configurational entropy of reduction via f-shells and simultaneous redox, and vetting materials stability via temperature-dependent phase diagrams and melting-point prediction.

08 HYDROGEN↗
DOE OSTI2025

UNR Grant Proposal Contribution

The work of Carrier et. al. (citation needed for Matt’s effect of surface roughness on phase transitions/ETI paper) demonstrates that 1D and 2D resistive magnetohydrodynamic (MHD) simulations can reliably model exploding aluminum rods driven by megaampere currents. Close agreement between simulation results and photonic Doppler velocimetry data from the Mykonos electrothermal instability (METI-II) campaign builds confidence in predictive modelling capabilities for pulsed-power HED experiments. Furthermore, 2D MHD simulations show how machined features and micro-scale surface roughness can seed the electrothermal instability (ETI). Surface roughness was observed to reduce the time of melt by 19%, with ETI growth driving the enhanced heating of the rod surface.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Core-Pedestal Plasma Configurations in Advanced Tokamaks

Here, several configurations for the core and pedestal plasma are examined for a predefined tokamak design by implementing multiple heating/current drive (H/CD) sources to achieve an optimum configuration of high fusion power in a noninductive operation while maintaining an ideally magnetohydrodynamic (MHD) stable core plasma using the IPS-FASTRAN framework. IPS-FASTRAN is a component-based lightweight coupled simulation framework that is used to simulate magnetically confined plasma by integrating a set of high-fidelity codes to construct the plasma equilibrium (EFIT, TOQ, and CHEASE), calculate the turbulent heat and particle transport fluxes (TGLF), model various H/CD systems (TORIC, TORAY, GENRAY, and NUBEAM), model the pedestal pressure and width (EPED), and estimate the ideal MHD stability (DCON). The TGLF core transport model and EPED pedestal model are used to self-consistently predict plasma profiles consistent with ideal MHD stability and H/CD (and bootstrap) current sources. In order to evaluate the achievable and sustainable plasma beta, varying configurations are produced ranging from the no-wall stability to with-wall stability regimes, simultaneously subject to the self-consistent TGLF, EPED, and H/CD source profile predictions that optimize configuration performance. The pedestal density, plasma current, and total injected power are scanned to explore their impact on the target plasma configuration, fusion power, and confinement quality. A set of fully noninductive scenarios are achieved by employing ion-cyclotron, neutral beam injection, helicon, and lower-hybrid H/CDs to provide a broad profile for the total current drive in the core region for a predefined tokamak design. These noninductive scenarios are characterized by high fusion gain (Q ~ 4) and power (P fus ~ 600 MW), optimum confinement quality (H 98 ~ 1.1), and high bootstrap current fraction (f BS ~ 0.7) for Greenwald fraction below unity. The broad current profile configurations identified are stable to low-n kink modes either because the normalized pressure β N is below the no-wall limit or a wall is present.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Thermoelectric heating and cooling–integrated dishwasher with thermal energy storage

Household dishwashers must address several performance goals: maximize washing and drying performance, while minimizing cycle duration, energy consumption, and water consumption. This study develops and examines a novel thermoelectric heating and cooling (TEHC) system with thermal energy storage applied to a household dishwasher (DW), aiming to improve the energy and drying performance of a commercially-available dishwasher while maintaining its washing performance, water consumption, and cycle duration. Experimental testing conducted on the novel TEHC-DW system demonstrates an 8.7% reduction in total energy consumption, lowering the per-cycle usage to 0.952 kWh, and a 40% reduction in energy consumption for internal water heating. The novel TEHC-DW system also demonstrates better drying performance, shortening the drying time by 42% to reach the same remaining moisture content as a commercially-available system. In addition, a resistance-capacitance network model is developed that predicts total drying time, total energy consumption, and the highest temperature reached in the tub (53.4 °C). The model accuracy is validated with experimental data (within ±1 K), and the model functions as a design tool via a parametric study to evaluate the next-generation design and the effect of the number of thermoelectric modules and thermoelectric driving force (i.e., current). Overall, this study demonstrates the potential for TEHC technology to improve energy efficiency and drying performance in household dishwashers.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Resolving ECRH deposition broadening due to edge turbulence in DIII-D

Microwave heat pulse propagation experiments have demonstrated a correlation between millimeter-scale turbulence and deposition profile broadening of electron cyclotron (EC) waves on the DIII-D tokamak. In a set of discharges in DIII-D, a variation in edge density fluctuations on the mm-scale is associated with 40%–150% broader deposition profiles, expressed in terms of normalized minor radius, as compared with equilibrium ray tracing. The 1D power profile is determined from transport analysis of the electron temperature response to EC power modulation using perturbative analysis with a square wave power modulation at 20–70 Hz, producing a series of Fourier harmonics that are fit collectively to resolve transport. Fitting an integrated heat flux expressed in the Fourier basis of the modulation to diffusive, convective, and coupled transport terms in a linear model can resolve the broadened EC deposition width from the power perturbation to resolve a broadening in each case. The best fit degree of beam broadening observed scales approximately linearly with the Doppler backscattering measured fluctuation level in the steep gradient region. Quantifying the effect of edge fluctuation broadening on EC current drive power needs of future devices will require 3D full-wave codes that can be validated on the current generation of machines. These DIII-D experiments provide a quantitative measure of fluctuation effects and a dataset to benchmark full-wave simulations that can model and eventually predict nonlinear effects neglected by 1D equilibrium beam and ray tracing.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Flow Assisted Evaporative Cooling for Electric Motor

This paper examines a novel concept of flow assisted latent heat driven two-phase evaporative cooling (EC) confined in-between slot liner and active-winding of electric motor. Wicking micro-structure enhanced PDMS liner axially sucks coolant in the form of thin film between the PDMS liner and active-winding and eventually enables thin film evaporation on the outer surface of the active-winding. Therefore, EC based thermal management eliminates contact resistance between the winding and slot-liner and, enhances the heat extraction from the winding without compromising the electro-magnetic performance. Two-way coupled electro-magnetic (EM) – computational fluid dynamics/heat transfer (CFD/HT) and EM - lumped parameter thermal network (LPTN) models have been developed to assess the electro-thermal performance of the EC under steady and transient conditions. Taking a case study of a 125 kW jacket cooled BMW i3 motor and dielectric coolant FC-84, EC is shown to be capable of handling a maximum steady state rms current density of 26 A/mm2 at a evaporative heat transfer coefficient of 5,000 W/m2.K, which is about 78.7% higher compared to the traditional jacket cooling (JC). In case of EC, a maximum steady state and transient rms current density of 30 A/mm2 (106.2% higher compared to the JC), and 40.8 A/mm2 have been realized by using high thermal conductivity epoxy (1.9 W/m.K) impregnation material. Thermal performance of the EC is also assessed and compared with JC over a dynamic drive cycle. Lastly, a motorette testing has been performed to demonstrate the applicability of the proposed EC method and to validate the developed modeling framework.

42 ENGINEERING↗
NASA NTRS2003

Numerical Simulation of Waves Driven by Plasma Currents Generated by Low-Frequency Alfven Waves in a Multi-Ion Plasma

When multi-ion plasma consisting of heavy and light ions is permeated by a lowfrequency Alfien (LFA) wave, the EXB and the polarization drifts of the different ion species and the electrons could be quite different. The relative drifts between the charged-particle species drive waves, which energize the plasma. Using 2.5-D particle-in-cell simulations, we study this process of wave generation and its nonlinear consequences in terms of acceleration and heating plasma. Specifically we study the situation for LFA wave frequency being lower than the heavyion cyclotron frequency in a multi-ion plasma. We impose such a wave to the plasma assuming that its wavelength is much larger than that of the waves generated by the relative drifts. For better understanding, the LFA-wave driven simulations are augmented by those driven by initialized ion beams.

Singh, Nagendra↗
DOE OSTI2021

Graphene overcoats for ultra-high storage density magnetic media

Hard disk drives (HDDs) are used as secondary storage in digital electronic devices owing to low cost and large data storage capacity. Due to the exponentially increasing amount of data, there is a need to increase areal storage densities beyond ~1 Tb/in 2 . This requires the thickness of carbon overcoats (COCs) to be <2 nm. However, friction, wear, corrosion, and thermal stability are critical concerns below 2 nm, limiting current technology, and restricting COC integration with heat assisted magnetic recording technology (HAMR). Here we show that graphene-based overcoats can overcome all these limitations, and achieve two-fold reduction in friction and provide better corrosion and wear resistance than state-of-the-art COCs, while withstanding HAMR conditions. Thus, we expect that graphene overcoats may enable the development of 4–10 Tb/in 2 areal density HDDs when employing suitable recording technologies, such as HAMR and HAMR+bit patterned media.

36 MATERIALS SCIENCE↗