Search NASA⌕ Search

SEARCH · Search NASA

Results for “high dimensional data analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Thermographic Phosphor Measurements of Shock-Shock Interactions on a Swept Cylinder

The effects of fin leading-edge radius and sweep angle on peak heating rates due to shock-shock interactions were investigated in the NASA Langley Research Center 20-inch Mach 6 Air Tunnel. The fin model leading edges, which represent cylindrical leading edges or struts on hypersonic vehicles, were varied from 0.25 inches to 0.75 inches in radius. A 9deg wedge generated a planar oblique shock at 16.7deg to the flow that intersected the fin bow shock, producing a shock-shock interaction that impinged on the fin leading edge. The fin angle of attack was varied from 0deg (normal to the free-stream) to 15deg and 25deg swept forward. Global temperature data was obtained from the surface of the fused silica fins using phosphor thermography. Metal oil flow models with the same geometries as the fused silica models were used to visualize the streamline patterns for each angle of attack. High-speed zoom-schlieren videos were recorded to show the features and temporal unsteadiness of the shock-shock interactions. The temperature data were analyzed using one-dimensional semi-infinite as well as one- and two-dimensional finite-volume methods to determine the proper heat transfer analysis approach to minimize errors from lateral heat conduction due to the presence of strong surface temperature gradients induced by the shock interactions. The general trends in the leading-edge heat transfer behavior were similar for the three shock-shock interactions, respectively, between the test articles with varying leading-edge radius. The dimensional peak heat transfer coefficient augmentation increased with decreasing leading-edge radius. The dimensional peak heat transfer output from the two-dimensional code was about 20% higher than the value from a standard, semi-infinite onedimensional method.

Jones, Michelle L.↗
NASA NTRS2020

Experimental Investigation of Shock-Shock Interactions Over a 2D Wedge at M = 6

The effects of fin-leading-edge radius and sweep angle on peak heating rates due to shock-shock interactions were investigated in the NASA Langley Research Center 20-Inch Mach 6 Air Tunnel. The fin model leading edges, which represent cylindrical leading edges or struts on hypersonic vehicles, were varied from 0.25 inches to 0.75 inches in radius. A 9° wedge generated a planar oblique shock at 16.7° to the flow that intersected the fin bow shock, producing a shock-shock interaction that impinged on the fin leading edge. The fin angle of attack was varied from 0° (normal to the free-stream) to 15° and 25° swept forward. Global temperature data were obtained from the surface of the fused silica fins through phosphor thermography. Metal oil flow models with the same geometries as the fused silica models were used to visualize the streamline patterns for each angle of attack. High-speed zoom-schlieren videos were recorded to show the features and temporal unsteadiness of the shock-shock interactions. The temperature data were analyzed using one-dimensional semi-infinite as well as one- and two-dimensional finite-volume methods to determine the proper heat transfer analysis approach to minimize errors from lateral heat conduction due to the presence of strong surface temperature gradients induced by the shock interactions. The general trends in the leading-edge heat transfer behavior were similar for the three shock-shock interactions, respectively, between the test articles with varying leading-edge radius. The dimensional peak heat transfer coefficient augmentation increased with decreasing leading-edge radius. The dimensional peak heat transfer output from the two-dimensional code was about 20% higher than the value from a standard, semi-infinite one-dimensional method.

shock-shock interaction↗
NASA NTRS2023

Understanding the Deflection of the “Cartwheel CME”: Data Analysis and Modeling

We study the low corona evolution of the “Cartwheel” coronal mass ejection (CME; 2008 April 9) by- reconstructing its three-dimensional path and modeling it with magnetohydrodynamic simulations. This event exhibited a double deflection that has been reported and analyzed in previous works but whose underlying cause remained unclear. The Cartwheel CME traveled toward a coronal hole (CH) and against the magnetic gradients. Using a high-cadence, full-trajectory reconstruction, we accurately determine the location of the magnetic flux rope (MFR) and, consequently, the magnetic environment in which it is immersed. We find a pseudostreamer (PS) structure whose null point may be responsible for the complex evolution of the MFR at the initial phase. From the preeruptive magnetic field reconstruction, we estimate the dynamic forces acting on the MFR and provide a new physical insight into the motion exhibited by the 2008 April 9 event. By setting up a similar magnetic configuration in a 2.5D numerical simulation we are able to reproduce the observed behavior, confirming the importance of the PS null point. We find that the magnetic forces directed toward the null point cause the first deflection, directing the MFR toward the CH. Later, the magnetic pressure gradient of the CH produces the reversal motion of the MFR.

Solar prominences↗
NASA NTRSDate not supplied

SWIPE: Spectral Water Inversion Processor and Emulator

Degradation of Earth’s inland water resources due to anthropogenic perturbations and climate anomalies at both local and global scales continues to place human health at substantial risk. There is now a growing necessity to develop pragmatic approaches that allow timely and effective extrapolation of local processes, to spatially resolved global products, and to promote operational and sustainable resource policy management. This presentation will be discussing the progress made developing SWIPE: Spectral Water Inversion Processor and Emulator. SWIPE is a platform for advanced modeling of coastal and inland aquatic habitats. The goal is create a comprehensive and cohesive system to leverage recent advancements in computation and machine learning to develop a synthetic training ground for sensitivity studies and algorithm development. The four principal facets of SWIPE include: 1. Advanced two-layer coated sphere bio-optical modeling and GPU radiative transfer modeling, 2. Big Data involving massive synthetic spectral libraries of optical properties of various global aquatic particles, surface reflectance, and top-of-atmosphere reflectance, all at hyperspectral resolution leveraging high-end computing systems at NASA Ames Research Center, 3. Deep Learning for algorithm development for water quality inversion of concentrations of common biogeophysical variables as well as optics, full uncertainty characterization by water type, and forward emulation, and lastly, 4. Image Processing for application of developed retrieval algorithms for both hyperspectral and multispectral sensors with experimental corrections for global adjacency, noise, sunglint, and benthic reflectance. This presentation will demonstrate the Equivalent Algal Populations (EAP) two-layer coated sphere scattering model which has been used develop spectral libraries of hyperspectral inherent optical properties of roughly 80 species of phytoplankton, covering 15 different classes and nine taxonomic functional types. The EAP model was also used to derive spectral properties of 10 different non-algal particle functional types. Examples of how the SMART-G (Speed-up Monte-carlo Advanced Radiative Transfer using GPU) radiative transfer code is used to model optically complex aquatic signals will be presented and discussed in the context of creating a massive synthetic database which can leverage the full power of next generation machine learning techniques and high end computing for water quality inversion. We will discuss our active investigation in things like appropriate model architectures, dimensionality reduction techniques such as PCA and autoencoders, uncertainty quantification and abstaining, and which variables actually benefit most from hyperspectral information versus multispectral resolution. We are also curious about questions relating to cost/benefit analysis in terms of computation resources, neural network complexity, and data volumes. Answers to these questions will hopefully elaborate on cost efficiency for potential future sensor design considerations.

SWIPE↗
NASA NTRS2013

Computational Fluid Dynamics Uncertainty Analysis for Payload Fairing Spacecraft Environmental Control Systems

Spacecraft thermal protection systems are at risk of being damaged due to airflow produced from Environmental Control Systems. There are inherent uncertainties and errors associated with using Computational Fluid Dynamics to predict the airflow field around a spacecraft from the Environmental Control System. This proposal describes an approach to validate the uncertainty in using Computational Fluid Dynamics to predict airflow speeds around an encapsulated spacecraft. The research described here is absolutely cutting edge. Quantifying the uncertainty in analytical predictions is imperative to the success of any simulation-based product. The method could provide an alternative to traditional"validation by test only'' mentality. This method could be extended to other disciplines and has potential to provide uncertainty for any numerical simulation, thus lowering the cost of performing these verifications while increasing the confidence in those predictions. Spacecraft requirements can include a maximum airflow speed to protect delicate instruments during ground processing. Computationaf Fluid Dynamics can be used to veritY these requirements; however, the model must be validated by test data. The proposed research project includes the following three objectives and methods. Objective one is develop, model, and perform a Computational Fluid Dynamics analysis of three (3) generic, non-proprietary, environmental control systems and spacecraft configurations. Several commercially available solvers have the capability to model the turbulent, highly three-dimensional, incompressible flow regime. The proposed method uses FLUENT and OPEN FOAM. Objective two is to perform an uncertainty analysis of the Computational Fluid . . . Dynamics model using the methodology found in "Comprehensive Approach to Verification and Validation of Computational Fluid Dynamics Simulations". This method requires three separate grids and solutions, which quantify the error bars around Computational Fluid Dynamics predictions. The method accounts for all uncertainty terms from both numerical and input variables. Objective three is to compile a table of uncertainty parameters that could be used to estimate the error in a Computational Fluid Dynamics model of the Environmental Control System /spacecraft system. Previous studies have looked at the uncertainty in a Computational Fluid Dynamics model for a single output variable at a single point, for example the re-attachment length of a backward facing step. To date, the author is the only person to look at the uncertainty in the entire computational domain. For the flow regime being analyzed (turbulent, threedimensional, incompressible), the error at a single point can propagate into the solution both via flow physics and numerical methods. Calculating the uncertainty in using Computational Fluid Dynamics to accurately predict airflow speeds around encapsulated spacecraft in is imperative to the success of future missions.

Groves, Curtis E.↗
DOE OSTI2024

A Typing Discipline for High-Assurance Control Systems

This poster describes a typing discipline for high-assurance industrial systems based on three novel type systems. The first type system, information flow control (IFC), controls the flow of data through the system. The second system, dependent session types, restricts messages exchanged during the execution of a communication protocol to avoid dangerous states. The third system uses dimensional analysis to avoid subtle bugs that adversaries can exploit to cause the system to enter a dangerous state. This poster describes how a combination of these approaches can prevent sophisticated cyber attacks, such as the infamous Stuxnet incident, from occurring. In addition, we provide experimental evidence to support the claim that these approaches can be applied in control systems that are resource-constrained.

42 - ENGINEERING↗
NASA NTRS2014

Dissertation Defense Computational Fluid Dynamics Uncertainty Analysis for Payload Fairing Spacecraft Environmental Control Systems

Spacecraft thermal protection systems are at risk of being damaged due to airflow produced from Environmental Control Systems. There are inherent uncertainties and errors associated with using Computational Fluid Dynamics to predict the airflow field around a spacecraft from the Environmental Control System. This paper describes an approach to quantify the uncertainty in using Computational Fluid Dynamics to predict airflow speeds around an encapsulated spacecraft without the use of test data. Quantifying the uncertainty in analytical predictions is imperative to the success of any simulation-based product. The method could provide an alternative to traditional "validation by test only" mentality. This method could be extended to other disciplines and has potential to provide uncertainty for any numerical simulation, thus lowering the cost of performing these verifications while increasing the confidence in those predictions. Spacecraft requirements can include a maximum airflow speed to protect delicate instruments during ground processing. Computational Fluid Dynamics can be used to verify these requirements; however, the model must be validated by test data. This research includes the following three objectives and methods. Objective one is develop, model, and perform a Computational Fluid Dynamics analysis of three (3) generic, non-proprietary, environmental control systems and spacecraft configurations. Several commercially available and open source solvers have the capability to model the turbulent, highly three-dimensional, incompressible flow regime. The proposed method uses FLUENT, STARCCM+, and OPENFOAM. Objective two is to perform an uncertainty analysis of the Computational Fluid Dynamics model using the methodology found in "Comprehensive Approach to Verification and Validation of Computational Fluid Dynamics Simulations". This method requires three separate grids and solutions, which quantify the error bars around Computational Fluid Dynamics predictions. The method accounts for all uncertainty terms from both numerical and input variables. Objective three is to compile a table of uncertainty parameters that could be used to estimate the error in a Computational Fluid Dynamics model of the Environmental Control System /spacecraft system. Previous studies have looked at the uncertainty in a Computational Fluid Dynamics model for a single output variable at a single point, for example the re-attachment length of a backward facing step. For the flow regime being analyzed (turbulent, three-dimensional, incompressible), the error at a single point can propagate into the solution both via flow physics and numerical methods. Calculating the uncertainty in using Computational Fluid Dynamics to accurately predict airflow speeds around encapsulated spacecraft in is imperative to the success of future missions.

CFD↗
NASA NTRS2014

Dissertation Defense: Computational Fluid Dynamics Uncertainty Analysis for Payload Fairing Spacecraft Environmental Control Systems

Spacecraft thermal protection systems are at risk of being damaged due to airflow produced from Environmental Control Systems. There are inherent uncertainties and errors associated with using Computational Fluid Dynamics to predict the airflow field around a spacecraft from the Environmental Control System. This paper describes an approach to quantify the uncertainty in using Computational Fluid Dynamics to predict airflow speeds around an encapsulated spacecraft without the use of test data. Quantifying the uncertainty in analytical predictions is imperative to the success of any simulation-based product. The method could provide an alternative to traditional validation by test only mentality. This method could be extended to other disciplines and has potential to provide uncertainty for any numerical simulation, thus lowering the cost of performing these verifications while increasing the confidence in those predictions.Spacecraft requirements can include a maximum airflow speed to protect delicate instruments during ground processing. Computational Fluid Dynamics can be used to verify these requirements; however, the model must be validated by test data. This research includes the following three objectives and methods. Objective one is develop, model, and perform a Computational Fluid Dynamics analysis of three (3) generic, non-proprietary, environmental control systems and spacecraft configurations. Several commercially available and open source solvers have the capability to model the turbulent, highly three-dimensional, incompressible flow regime. The proposed method uses FLUENT, STARCCM+, and OPENFOAM. Objective two is to perform an uncertainty analysis of the Computational Fluid Dynamics model using the methodology found in Comprehensive Approach to Verification and Validation of Computational Fluid Dynamics Simulations. This method requires three separate grids and solutions, which quantify the error bars around Computational Fluid Dynamics predictions. The method accounts for all uncertainty terms from both numerical and input variables. Objective three is to compile a table of uncertainty parameters that could be used to estimate the error in a Computational Fluid Dynamics model of the Environmental Control System spacecraft system.Previous studies have looked at the uncertainty in a Computational Fluid Dynamics model for a single output variable at a single point, for example the re-attachment length of a backward facing step. For the flow regime being analyzed (turbulent, three-dimensional, incompressible), the error at a single point can propagate into the solution both via flow physics and numerical methods. Calculating the uncertainty in using Computational Fluid Dynamics to accurately predict airflow speeds around encapsulated spacecraft in is imperative to the success of future missions.

Fluid Dynamics↗
NASA NTRS1994

Time scales of pattern evolution from cross-spectrum analysis of advanced very high resolution radiometer and coastal zone color scanner imagery

We have selected square subareas (110 km on a side) from coastal zone color scanner (CZCS) and advanced very high resolution radiometer (AVHRR) images for 1981 in the California Current region off northern California for which we could identify sequences of cloud-free data over periods of days to weeks. We applied a two-dimensional fast Fourier transformation to images after median filtering, (x, y) plane removal, and cosine tapering. We formed autospectra and coherence spectra as functions of a scalar wavenumber. Coherence estimates between pairs of images were plotted against time separation between images for several wide wavenumber bands to provide a temporal lagged coherence function. The temporal rate of loss of correlation (decorrelation time scale) in surface patterns provides a measure of the rate of pattern change or evolution as a function of spatial dimension. We found that patterns evolved (or lost correlation) approximately twice as rapidly in upwelling jets as in the 'quieter' regions between jets. The rapid evolution of pigment patterns (lifetime of about 1 week or less for scales of 50-100 km) ought to hinder biomass transfer to zooplankton predators compared with phytoplankton patches that persist for longer times. We found no significant differences between the statistics of CZCS and AVHRR images (spectral shape or rate of decorrelation). In addition, in two of the three areas studied, the peak correlation between AVHRR and CZCS images from the same area occurred at zero lag, indicating that the patterns evolved simutaneously. In the third area, maximum coherence between thermal and pigment patterns occurred when pigment images lagged thermal images by 1-2 days, mirroring the expected lag of high pigment behind low temperatures (and high nutrients) in recently upwelled water. We conclude that in dynamic areas such as coastal upwelling systems, the phytoplankton cells (identified by pigment color patterns) behave largely as passive scalars at the mesoscale and that growth, death, and sinking of phytoplankton collectively play at most a mariginal role in determining the spectral statistics of the pigment patterns.

Denman, Kenneth L.↗
NASA NTRS1995

An Analytic Approximation to Very High Specific Impulse and Specific Power Interplanetary Space Mission Analysis

A simple, analytic approximation is derived to calculate trip time and performance for propulsion systems of very high specific impulse (50,000 to 200,000 seconds) and very high specific power (10 to 1000 kW/kg) for human interplanetary space missions. The approach assumed field-free space, constant thrust/constant specific power, and near straight line (radial) trajectories between the planets. Closed form, one dimensional equations of motion for two-burn rendezvous and four-burn round trip missions are derived as a function of specific impulse, specific power, and propellant mass ratio. The equations are coupled to an optimizing parameter that maximizes performance and minimizes trip time. Data generated for hypothetical one-way and round trip human missions to Jupiter were found to be within 1% and 6% accuracy of integrated solutions respectively, verifying that for these systems, credible analysis does not require computationally intensive numerical techniques.

Williams, Craig Hamilton↗
NASA NTRS1994

Analytical investigation of the dynamics of tethered constellations in Earth orbit, phase 2

This final report covers nine years of research on future tether applications and on the actual flights of the Small Expendable Deployment System (SEDS). Topics covered include: (1) a description of numerical codes used to simulate the orbital and attitude dynamics of tethered systems during station keeping and deployment maneuvers; (2) a comparison of various tethered system simulators; (3) dynamics analysis, conceptual design, potential applications and propagation of disturbances and isolation from noise of a variable gravity/microgravity laboratory tethered to the Space Station; (4) stability of a tethered space centrifuge; (5) various proposed two-dimensional tethered structures for low Earth orbit for use as planar array antennas; (6) tethered high gain antennas; (7) numerical calculation of the electromagnetic wave field on the Earth's surface on an electrodynamically tethered satellite; (8) reentry of tethered capsules; (9) deployment dynamics of SEDS-1; (10) analysis of SEDS-1 flight data; and (11) dynamics and control of SEDS-2.

Lorenzini, Enrico C.↗
NASA NTRS1996

High-Performance Computing and Four-Dimensional Data Assimilation: The Impact on Future and Current Problems

This is the final technical report for the project entitled: "High-Performance Computing and Four-Dimensional Data Assimilation: The Impact on Future and Current Problems", funded at NPAC by the DAO at NASA/GSFC. First, the motivation for the project is given in the introductory section, followed by the executive summary of major accomplishments and the list of project-related publications. Detailed analysis and description of research results is given in subsequent chapters and in the Appendix.

Makivic, Miloje S.↗
NASA NTRS1978

Analysis of stability contributions of high dihedral V-tails

An investigation was undertaken to determine the effectiveness of four analytical methods (empirical, modified empirical, vortex-lattice, and an inviscid, three dimensional, potential flow, wing body program) to estimate the lateral and longitudinal static stability characteristics of an isolated V-tail wind tunnel model. The experimental tests were conducted in the V/STOL tunnel at a Mach number of 0.18. Angle-of-attack data were obtained from -12 deg to 8 deg at 0 deg sideslip. Sideslip sweeps from -5 deg to 10 deg were made at angles of attack of 4 deg, 0 deg and -4 deg. The V-tail dihedral angles were 45 deg, 50 deg, 55 deg, and 60 deg.

Freeman, C. E.↗
DOE OSTI2025

Dynamic Strength and Equation of State of Epon 828 and Diethanolamine (DEA) Polymer Epoxy Under Shock Loading

Polymers are increasingly utilized in engineering applications that can experience high loading rates, necessitating increased understanding of their response under such conditions. The tamped Richtmyer-Meshkov Instability (RMI) method was used to characterize the equation of state and dynamic strength of the polymer Epon 828 cured with Diethanolamine (DEA). Plate impact experiments that drove a uniaxial shock compression wave across a sinusoidally corrugated metal-polymer interface were performed to generate shock stresses from 4-12 GPa and strain rates of approximately 1/s in the polymer. X-ray phase contrast imaging recorded the shock motion in the polymer and subsequent interface evolution. Analysis of this data yielded the polymer equation of state and, in conjunction with numerical modeling, the dynamic strength. The equation of state was validated against one-dimensional plate impact experiments from existing literature. The dynamic strength was compared to prior data for Epon 828 and related polymers at lower strain rates and found to exhibit significant strain rate and pressure-hardening effects. The strength of the Epon 828 polymer at 10 6 1/s was found to be approximately 1.5 GPa, suggesting that it is comparable to the strength of high strength metals at these dynamic conditions.

Equation of state↗
DOE OSTI2024

Comprehensive characterization of the irradiation effects of glassy carbon

Carbon materials have become increasingly diverse, finding applications in high-temperature and high-radiation environments. Glassy carbon, an allotrope known for its exceptional chemical inertness and desirable mechanical properties. However, understanding neutron irradiation effects in glassy carbon has proven challenging, primarily because of its unique nanopore structure. Here, this study presents a highly detailed microstructural characterization investigation of neutron-induced changes in glassy carbon, revealing how changes in nanopore structure and crystallinity impact the irradiation-induced shrinkage. Aberration-corrected scanning transmission electron microscopy (STEM) reveals pore closure that leads to material densification in the irradiated samples. Dimensional analysis combined with comparison to historical data suggest significant length shrinkage to occur. Neutron and in situ electron irradiation experiments suggest that glassy carbon transforms into so-called carbon onions, supporting the concept of shrinkage saturation. Investigating irradiation temperature effects using STEM, electron energy loss spectroscopy, x-ray diffraction, and Raman spectroscopy revealed partial amorphization at 210 °C–230 °C and preserved order in glassy carbon at 860 °C, coinciding with pore closure. Thermal property measurements were also conducted to assess the effects of densification and other changes in the atomic structure of glassy carbon. The results of this study have broad implications in the deployment of glassy carbon to nuclear environments, based around the observed changes in the thermal properties, and demonstrates the operational window for the onset of densification.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multidimensional Rietveld refinement of high-pressure neutron diffraction data of PbNCN

High-pressure neutron powder diffraction data from PbNCN were collected on the high-pressure diffraction beamline SNAP located at the Spallation Neutron Source (SNS) of Oak Ridge National Laboratory (Tennessee, USA). The diffraction data were analyzed using the novel method of multidimensional (two dimensions for now, potentially more in the future) Rietveld refinement and, for comparison, employing the conventional Rietveld method. To achieve two-dimensional analysis, a detailed description of the SNAP instrument characteristics was created, serving as an instrument parameter file, and then yielding both cell and spatial parameters as refined under pressure for the first time for solid-state cyanamides/carbodiimides. The bulk modulus B 0 = 25.1 (15) GPa and its derivative B ′ 0 = 11.1 (8) were extracted for PbNCN following the Vinet equation of state. Surprisingly, an internal transition was observed beyond 2.0 (2) GPa, resulting from switching the bond multiplicities (and bending direction) of the NCN 2− complex anion. The results were corroborated using electronic structure calculation from first principles, highlighting both local structural and chemical bonding details.

Meinerzhagen, Yannick↗
NASA NTRS1989

Stellar occultation of polarized light from circumstellar electrons. I - Flat envelopes viewed edge on

The depolarizing and occultation effects of a finite spherical light source on the polarization of light Thomson-scattered from a flat circumstellar envelope seen edge-on are analyzed. The analysis shows that neglect of the finite size of the light source leads to a gross overestimate of the polarization for a given disk geometry. By including occultation and depolarization, it is found that B-star envelopes are necessarily highly flattened disk-type structures. For a disk viewed edge-on, the effect of occultation reduces the polarization more than the inclusion of the depolarization factor alone. Analysis of a one-dimensional plume leads to a powerful technique that permits the electron density distribution to be explicitly obtained from the polarimetric data.

Brown, John C.↗
NASA NTRS1993

Experimental investigation of nozzle/plume aerodynamics at hypersonic speeds

Work continued on the improvement of 16-Inch Shock Tunnel. This comprised studies of ways of improving driver gas ignition, an improved driver gas mixing system, an axial translation system for the driver tube, improved diaphragm materials (carbon steel vs. stainless steel), a copper liner for the part of the driven tube near the nozzle, the use of a buffer gas between the driver and driven gases, the use of N2O in the driven tube, the use of a converging driven tube, operation of the facility as a non-reflected shock tunnel and expansion tube, operation with heated hydrogen or helium driver gas, the use of detonations in the driver and the construction of an enlarged test section. Maintenance and developmental work continued on the scramjet combustor continued. New software which greatly speeds up data analysis has been written and brought on line. In particular, software which provides very rapid generation of model surface heat flux profiles has been brought on line. A considerable amount of theoretical work was performed in connection with upgrading the 16 Inch Shock Tunnel Facility. A one-dimensional Godunov code for very high velocities and any equation of state is intended to add viscous effects in studying the operation of the Shock Tunnel and also of two-stage light gas guns.

Bogdanoff, David W.↗