Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Modification of eutectic Mg2Si in AlMg5Si2Mn alloy by pre-homogenization deformation treatment with different reduction conditions

Highlights: • PHD treatment was proposed to modify Mg{sub 2}Si morphology of extruded AlMg5Si2Mn alloy. • PHD treatment accelerated spheroidization of eutectic Mg{sub 2}Si in AlMg5Si2Mn alloy. • Tensile properties of AlMg5Si2Mn extrudates were improved by introduction of PHD. - Abstract: The effect of a novel pre-homogenization deformation (PHD) treatment on the microstructure and mechanical properties of extruded AlMg5Si2Mn alloy was investigated. By introducing the cold compression prior to homogenization treatment, the brittle and interconnected eutectic Mg{sub 2}Si phase in the as-cast AlMg5Si2Mn alloy transformed into fine and spherical particles uniformly dispersed in the aluminum matrix. As the amount of PHD increased, up to 10%, the size of the Mg{sub 2}Si particles decreased and their sphericity increased in the extruded samples, resulting in a gradual increase in both strength and elongation after heat treatment. The mechanical properties of the PHD-treated AlMg5Si2Mn extrudates were compared with those of materials prepared using various casting and deformation processes, and the potential application to wrought products was discussed.

36 MATERIALS SCIENCE↗

Advanced detector signal acquisition and electron beam scanning for high resolution SEM imaging

We report the advancement of materials science at the mesoscale requires improvements in both sampling volumes/areas and spatial resolution in order to make statistically significant measurements of microstructures that influence higher-order material properties, such as fatigue and fracture. Therefore, SEM-based techniques have become desirable due to improvements in imaging resolution, large sample handling capability, and flexibility for in-situ instrumentation. By using fast sampling of SEM electron detector signals, intrinsic beam scanning defects have been identified that are related to the response time of the SEM electron beam deflectors and electron detectors. Mitigation of these beam scanning defects using detector sampling approaches and an adaptive model for settling time is shown to produce higher resolution SEM images, at faster image acquisition times, with a means to quantify the different response functions for various beam deflectors and detectors including those for electrons and ions.

47 OTHER INSTRUMENTATION↗

Spacer-less, decoupled granular L1{sub 0} FePt magnetic media using Ar-He sputtering gas

Spacer materials are often used to fabricate granular L1{sub 0} FePt media and reduce the grain size, however, at the expense of reduced out-of-plane coercivity. Here, we demonstrate a spacer-less method in which adding 1% helium to argon sputtering gas leads to a substantial improvement in the chemical ordering, as well as the magnetic and microstructural properties of FePt. This change is attributed to the modification in the ion current density of the plasma caused by the excited metastable helium species. Helium plays a pivotal role in providing the Fe and Pt atoms optimal adatom mobility, thereby, producing well-ordered L1{sub 0} FePt media. This leads to an enhancement of the out-of-plane coercivity from 15 to 22 kOe. Furthermore, exchange decoupled grains with a twofold reduction in their diameter to {approx}24 nm are also achieved. These properties are crucial for magnetic media of the future for data storage recording densities beyond 1 Tb/in{sup 2}.

36 MATERIALS SCIENCE↗

Creep behavior of tungsten/niobium and tungsten/niobium-1 percent zirconium composites

The creep behavior and microstructural stability of tungsten fiber reinforced niobium and niobium 1 percent zirconium was determined at 1400 and 1500 K in order to assess the potential of this material for use in advanced space power systems. The creep behavior of the composite materials could be described by a power law creep equation. A linear relationship was found to exist between the minimum creep rate of the composite and the inverse of the composite creep rupture life. The composite materials had an order of magnitude increase in stress to achieve 1 percent creep strain and in rupture strength at test temperatures of 1400 and 1500 K compared to unreinforced material. The composite materials were also stronger than the unreinforced materials by an order of magnitude when density was taken into consideration. Results obtained on the creep behavior and microstructural stability of the composites show significant potential improvement in high temperature properties and mass reduction for space power system components.

Petrasek, Donald W.↗

Overcoming mechanical fragility in Sm-Co permanent magnet materials

Samarium-cobalt alloys are used in some of the strongest permanent magnets, particularly for applications between about 200 and 550°C, but the utilization of these materials is restricted by their brittleness. Improving their mechanical resilience would allow them to be used more widely and, in some cases, substitute for neodymium-based magnet alloys which are subject to supply-chain risks. In this work, we have engineered a series of novel microstructures with bi-modal grain size distributions to achieve unprecedented combinations of mechanical and magnetic properties. Improvements up to 73% are obtained in the flexural strength of Sm 2 (CoFeCuZr) 17 sintered magnets, with negligible impact on the magnetic properties. Our mechanically-robust, high-performance Sm-Co magnets are made without changing the chemical compositions of the materials or their heat treatment procedures, making them highly compatible with existing manufacturing processes.

36 MATERIALS SCIENCE↗

Microstructure Evolution and Mechanical Properties of Large-Scale AZ80 Magnesium Alloy Billets Produced by Multitemperature Multidirectional Forging

Grain refinement is an effective method to improve the mechanical properties of magnesium (Mg) alloys. In the present research, the combination of multidirectional forging (MDF) and forward extrusion for sizing with decreasing temperature pass by pass was employed to deform as-cast AZ80 magnesium alloy billet with large size to obtain fine grains and homogeneous microstructure. It was found that with the increasing number of MDF passes, the average grain size decreases; the homogeneity of microstructures and the percentages of dynamic recrystallised grains increase simultaneously. After six-pass MDF, fine and homogeneous microstructure with an average grain size of 15 μm was achieved; however, grain refinement became very difficult with a further increase in the MDF pass number. After eight-pass MDF plus forward extrusion for sizing, excellent mechanical properties of large-scale AZ80 magnesium alloy billet were obtained. The tensile strength, the yield strength and the elongation of billet are 410 MPa, 292 MPa and 14%, respectively. Furthermore, during multitemperature MDF, the inverse of the square root of grain size and tensile yield strength fit well with the Hall–Petch relationship.

36 MATERIALS SCIENCE↗

High entropy alloys: A focused review of mechanical properties and deformation mechanisms

The high-entropy alloy (HEA) concept was based on the idea that high mixing entropy can promote formation of stable single-phase microstructures. During the past 15 years, various alloy systems have been explored to identify HEA systems with improved property combinations, leading to an extraordinary growth of this field. In the large pool of alloys with varying characteristics, the first single-phase HEA with good tensile properties, the equiatomic CrMnFeCoNi alloy has become the benchmark material, and it forms the basis of much of our current fundamental understanding of HEA mechanical behavior. As the field is evolving to the more broadly defined complex concentrated alloys (CCAs) and the available data in the literature increase exponentially, a fundamental question remains unchanged: how special are these new materials? In the first part of this review, select mechanical properties of HEAs and CCAs are compared with those of conventional engineering alloys. This task is difficult because of the limited tensile data available for HEAs and CCAs. Additionally, the wider suite of mechanical properties needed to assess structural materials is woefully lacking. Nonetheless, our evaluations have not revealed many HEAs or CCAs with properties far exceeding those of conventional engineering alloys, although specific alloys can show notable enhancements in specific properties. Consequently, it is reasonable to first approach the understanding of HEAs and CCAs through the assessment of how the well-established deformation mechanisms in conventional alloys operate or are modified in the presence of the high local complexity of the HEAs and CCAs. The second part of the paper provides a detailed review of the deformation mechanisms of HEAs with the FCC and BCC structures. For the former, we chose the CrMnFeCoNi (Cantor) alloy because it is the alloy on which the most rigorous and thorough investigations have been performed and, for the latter, we chose the TiZrHfNbTa (Senkov) alloy because this is one of the few refractory HEAs that exhibits any tensile ductility at room temperature. As expected, our review shows that the fundamental deformation mechanisms in these systems, and their dependence on basic physical properties, are broadly similar to those of conventional FCC and BCC metals. The third part of this review examines the theoretical and modeling efforts to date that seek to provide either qualitative or quantitative understanding of the mechanical performance of FCC and BCC HEAs. Since experiments reveal no fundamentally new mechanisms of deformation, this section starts with an overview of modeling perspectives and fundamental considerations. Next, the review turns to the evolution of modeling and predictions as compared to recent experiments, highlighting both successes and limitations. Finally, in spite of some significant successes, important directions for further theory development are discussed. Overall, while the individual deformation mechanisms or properties of the HEAs and CCAs are not, by and large, “special” relative to conventional alloys, the present HEA rush remains valuable because the compositional freedom that comes from the multi-element space will allow exploration of whether multiple mechanisms can operate sequentially or simultaneously, which may yet lead to the creation of new alloys with a spectrum of mechanical properties that are significantly superior to those of current engineering alloys.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Copper Billets Fabricated by the Repetitive Extrusion and Free Forging Process

In the present study, with the aim of obtaining a weakened texture, grain refinement and improved mechanical properties, copper billets were successfully fabricated using the severe plastic deformation method of repetitive extrusion and free forging (REFF) without using any additional tools or devices. The evolution of the microstructure, texture and mechanical behavior of the ultrafine grain copper billets over an increasing number of REEF cycles was also systematically studied. Our results show that the effective strain per REFF process was ε = 2.35. After two cycles of REFF process, the sum effective strain became ε = 4.7, leading to high efficiency of grain refinement. The grain size was refined from 50 to 0.8 μm; the yield strength was increased to 462 MPa, and we obtained a weakened texture in the pure copper billets. By increasing the number of cycles, the grain refinement ability was decreased, and the texture was thus strengthened further. Therefore, two cycles of REFF were a reasonable process for producing ultrafine-grained copper billets.

36 MATERIALS SCIENCE↗

The Effect of Process History on Grain Boundaries and Dislocation Substructures on Functional Properties of Nb for SRF Cavities: Plastic Formability and Microstructural Evolution. Final report

While much progress has been made in improving the performance of cavities in the past decade, reproducible performance remains elusive. This renewal of “The cost of grain boundaries on the performance of superconducting cavities” examines in further depth the interactions between forming and annealing processes and functional performance at the scale of dislocation substructure and grain boundaries. There are five tasks identified in the renewal, which are: Characterization / analysis of current cavity technology: Effect of deformation, heat treatment, surface treatments, and residual damage on cavity function (Lee and Bieler) Characterization of dislocation mechanisms in single and bicrystals (Bieler) Quantifying effects of impurities and deformation mechanisms in Nb using density functional theory calculations (Solanki) Crystal plasticity constitutive model development (Pourboghrat and Eisenlohr) Modeling and measuring thermal conductivity in thin layers (Wright)

36 MATERIALS SCIENCE↗

Microstructure and Properties of AlCoCrFeNiTi High-Entropy Alloy Coating on AISI1045 Steel Fabricated by Laser Cladding

AISI1045 steel is widely used in mechanical engineering. In spite of the favorable toughness and strength, the surface properties of AISI1045 steel, such as hardness, wear resistance and corrosion resistance, are not ideal. Therefore, surface modification of AISI1045 is necessary, especially for the parts suffering severe work condition. Laser cladding is a promising surface modification technology. In this work, the AlCoCrFeNiTi high-entropy alloy (HEA) coatings were prepared on the AISI1045 steel to improve its surface properties. Metallurgical bonding is obtained between the coating and the substrate. The microstructure and surface properties of the coating were characterized by scanning electron microscope, energy-dispersive spectrometry, x-ray diffraction, electrochemical workstation, microhardness tester and pin-on-ring wear tester. The microstructure of the coating produced by laser cladding is dendritic. The AlCoCrFeNiTi HEA coating is mainly composed of disordered body-centered cubic phase (Fe-Cr), ordered B2 phase (AlNi) and intermetallic phase (Ti-rich). The coating shows excellent abrasion resistance and corrosion resistance in comparison with the substrate. The maximum microhardness of the coating reaches approximately 865 HV, which is 4.5 times of AISI1045 steel.

36 MATERIALS SCIENCE↗

Prediction of crack propagation paths in the unit cell of SOFC stacks

Planar Solid Oxide Fuel Cells (SOFC) stacks are multi-material layered systems with different thermo-mechanical properties. Due to their severe thermal loading, these layers have to meet high demands to preserve their mechanical integrity without initiation and propagation of fracture. Here, we focus on a typical unit cell of the stack which consists of positive electrode-electrolyte-negative electrode (PEN). Based on the mechanical properties of each layer and their interfaces, an energy criterion as a function of crack length is used for the prediction of possible crack extensions in the PEN. This criterion is a pure local criterion, independent of applied loads and geometry of the specimen. An analysis of the competition between crack deflections in the interfaces and crack penetration in layers is presented.

30 DIRECT ENERGY CONVERSION↗

Drawing Direction Effect on Microstructure and Mechanical Properties of Twinning-Induced Plasticity Steel During Wire Drawing

The effect of drawing direction on microstructure and mechanical properties in twinning-induced plasticity (TWIP) steel during wire drawing has been investigated to improve drawability for wire rod applications. The steel wires subjected to unidirectional (UD) and reverse-directional (RD) wire drawing were analyzed. The yield and tensile strength processed by the RD were slightly higher than those by the UD, whereas the ductility and drawability have inverse features, which is totally different from the results of plain carbon steel and Al wire. Although final shear strain of wires deformed by the RD is lower than that by the UD, the RD wires had a more complex stress history and a higher <111> texture component at the surface area, which encouraged twinning rate, resulting in fast exhaustion of ductility, finally earlier fracture of wires. In contrast to the materials deformed by mainly slip mechanism, the RD process cannot improve the ductility and drawability in TWIP steel due to the stress state dependency of twinning mechanism. Also, based on the different strengthening behaviors between pearlitic and TWIP steels during UD and RD, it is induced that microstructure and applied stress state simultaneously control the mechanical properties.

36 MATERIALS SCIENCE↗

Sintering dense NiZn ferrite by two-step sintering process

A two-step sintering process has been adopted to produce NiZn ferrite with composition of (NiO){sub 0.35}(ZnO){sub 0.57}(CuO){sub 0.08}(Fe{sub 2}O{sub 3}). The densification, microstructure, and magnetic properties of the ferrite have been investigated and compared with those of ferrites produced by the traditional final-stage sintering process. It was found that the sample produced by a two-step sintering process with a high temperature of 1200 deg. C and a lower temperature of 1100 deg. C attained more than 96% of the theoretical density and had a uniform microstructure with a small average grain size. It also exhibited good performances in terms of permeability and Q-factor. Hence, this would seem to be an effective method for producing dense ferrites with a microstructure composed of small and even grains, which is a very effective strategy for improving the magnetic properties of ferrites.

36 MATERIALS SCIENCE↗

Influence of Powder Characteristics and Processing Methods on Creep Performance of Powder Metallurgy Hot Isostatic Pressed SS316

The U.S. nuclear energy expansion goals are driving the demand for manufacturing routes that can rapidly produce large, complex, near net shape components. Powder metallurgy hot isostatic pressing (PM HIP) is an advanced manufacturing technique that can be economically scaled-up, while alleviating the supply chain challenges that forging and casting face in terms of cost and lead time constraints. This makes PM-HIP a viable technology to aid and accelerate large-scale part manufacturing for nuclear applications. However, large-scale qualification and deployment of this technology require a thorough understanding of the influence of powder feedstock quality, powder handling history, hot isostatic pressing (HIP) parameters, and subsequent heat treatment on microstructural evolution and elevated temperature mechanical performance. The present work focusses on 316 austenitic stainless steel (SS316) which is most commonly used in high temperature environments for nuclear applications Results from this study show that PM HIPed SS316 meets ASME tensile requirements at room temperature and at elevated temperature. However, creep performance of PM-HIPed SS316 remains inferior to its wrought counterpart, demonstrating that tensile performance alone is not a reliable metric for long duration high temperature integrity. Further, this report delineates powder derived microstructural features that govern creep damage, with key evidences pointing to “microstructural inheritance” from gas atomized powder feedstocks. Commercial SS316 powders of varying chemical compositions and recycling histories were studies, and the results showed large differences in elemental segregation, oxide surface layers and secondary phase distributions. Multi-scale characterization revealed segregation of chromium, molybdenum, manganese and silicon at the boundaries and the precipitation of manganese-, silicon-, and molybdenum-oxides. During HIP consolidation, these surface oxides transform into decorated prior particle boundaries (PPBs) and grain boundary inclusions that persist through conventional post-HIP solution annealing treatment. The retained oxides in post-HIP microstructures were found to influence grain growth, precipitation behavior, and ultimately creep cavitation and fracture. Such post-HIP heat treatments are therefore limited by a complex trade-off between grain growth, and oxide coarsening which aggravate creep damage by acting as nucleation sites for cavities. The objective of this work is to establish an integrated processing–structure–property framework for PM-HIP 316 stainless steel by investigating the influence of powder feedstock characteristics in pre- and post-HIP processing as well as to understand the significance of post-HIP heat treatment on microstructural evolution and creep properties. The results from this report emphasize the significance of powder feedstock integrity in improving creep performance of PM-HIPed SS316, by highlight the effect of rapid solidification, elemental segregation, oxide formation and powder recycling on microstructural defect inheritance following HIP consolidation. Rather than considering HIP processing, solution annealing, and mechanical performance independently, this report treats powder production, HIP consolidation, post-HIP thermal processing, and creep deformation as interconnected stages within a continuous metallurgical process. The resulting framework will provide a scientific basis for developing feedstock engineering strategies capable of improving long-term reliability of PM-HIP stainless steels and accelerating their qualification for advanced nuclear applications.

Ajjarapu, Pavan [Oak Ridge National Laboratory (OR↗

Enhancing microsegregation during rapid directional solidification through ternary microalloying

The nano-cellular dendritic microstructure formed during rapid directional solidification in powder bed fusion additive manufacturing creates unique properties such as simultaneous improvement in strength and ductility. However, process control of microsegregation features remains challenging due to low sensitivity of critical solidification mechanisms to process parameters. This study leverages microalloying to achieve large changes in dendrite composition, microstructure, and interdendritic zone width during laser powder bed fusion without modifying process parameters. CALPHAD simulations predict that the addition of Zr significantly steepens the solidus line of the dilute Cu-Cr alloy system, leading to enhanced Cr rejection into the melt and greater than 95% reduction in solubility of Cr in the solidified Cu matrix. Experimental validation using time-of-flight secondary ion mass spectrometry and Kelvin probe force microscopy reveals that the ternary alloy containing 0.01 wt% Zr exhibited wider interdendritic regions compared to the binary, a significantly higher number of Cr-rich particles within interdendritic regions, near-complete ejection of oxygen impurities from the matrix, and greater nanoscale work function contrast. These features indicate more aggressive Cr segregation in the presence of Zr and a purer Cu matrix and provide a potentially robust method for engineering the nano-cellular dendritic solidification microstructure.

CALPHAD↗

Analyzing the Effect of CeB{sub 6} on Microstructure and Mechanical Properties of High-Speed Steel Consolidated by Powder Metallurgy

By adding various amounts of CeB{sub 6}, high-speed steel (M3:2) was consolidated by powder metallurgy in the form of sintering. The addition of CeB{sub 6} improved the density of the sintered steel and the formation of M{sub 6}C phase in microstructure. It is speculated that CeB{sub 6} was decomposed into boron and cerium. Boron atoms were enriched in M{sub 6}C carbide phases, but cerium atoms were mainly clustered on grain boundary while they were converted to oxides, whereby the mechanical properties were improved. For example, upon the sintering at 1210 °C, relative density ~ 98.5% and average grain size ~ 18 μm were obtained with CeB{sub 6} content at 0.3 wt.%. Excellent mechanical properties, e.g., the Rockwell hardness ~ 52 HRC, flexural strength ~ 3.05 GPa, and fracture toughness ~ 40.92 MPa m{sup 1/2}, were achieved in the sample containing 0.3 wt.% CeB{sub 6}, which implies accordingly remarkable increases by 23.5, 38.1, and 23.7%, of the properties compared with those in the sample free of CeB{sub 6}.

36 MATERIALS SCIENCE↗

Use of High Magnetic Fields to Improve Material Properties for Hydraulics, Automotive and Truck Components

In this CRADA, research and development activities were successfully conducted on magnetic processing effects for the purpose of manipulating microstructure and the application specific performance of three alloys provided by Eaton (alloys provided were: carburized steel, plain low carbon steel and medium carbon spring steel). Three specific industrial/commercial application areas were considered where HMFP can be used to provide significant energy savings and improve materials performance include using HMFP to: 1.) Produce higher material strengths enabling higher torque bearing capability for drive shafts and other motor components; 2.) Increase the magnetic response in an iron-based material, thereby improving its magnetic permeability resulting in improved magnetic coupling and power density, and 3.) Improve wear resistance. The very promising results achieved in this endeavor include: 1.) a significant increase in tensile strength and a major reduction in volume percent retained austenite for the carburized alloy, and 2.) a substantial improvement in magnetic perm respect to a no-field processed sample (which also represents a significant improvement over the nominal conventional automotive condition of no heat treatment). The successful completion of these activities has resulted in the current 3-year CRADA No. NFE-09-02522 Prototyping Energy Efficient ThermoMagnetic and Induction Hardening for Heat Treat and Net Shape Forming Applications .

Eaton Innovation Center↗

Microstructure and Mechanical Behavior of Heat-Treated and Thermomechanically Processed TA15 Ti Alloy Composites

For TA15 Ti alloy, which has been widely used to form key load-bearing components in aeronautic and space fields, particular performances and corresponding microstructures are demanded due to various service environments. By applying single-phase field heat treatment, single-phase + two-phase field heat treatments, forging (α + β phase zone) combined with high-temperature aging and dual heat treatment, four types of microstructures, namely the fully lamellar microstructure, basket weave microstructure, two-phase composite microstructure and tri-modal microstructure, were obtained, respectively. And after conducting mechanical property tests for these microstructures, it was found that enhancing the lamellar thickness in the fully lamellar microstructures, reducing the content of equiaxed α phase to about 20% or increasing the content of lamellar phase in the two-phase composite microstructures and controlling the content of equiaxed α phase within 20% in the tri-modal microstructure were beneficial for performance improving. In addition, two-phase and three-phase composite microstructures possessed excellent comprehensive mechanical properties, and fully lamellar microstructures had the highest fracture toughness.

36 MATERIALS SCIENCE↗