Search NASA⌕ Search

SEARCH · Search NASA

Results for “interdiffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Layer dissolution in accumulative roll bonded bulk Zr/Nb multilayers under heavy-ion irradiation

In this work, the heavy-ion irradiation behavior of bulk zirconium-niobium multilayered composites was investigated up to large doses. Multilayers with an average individual layer thicknesses ranging between 15 and 80 nm were synthesized by accumulative roll bonding technique. The irradiation was performed with a defocused 7 MeV Zr 2+ ion beam at 500 °C. The maximum dose achieved was ~145 dpa at the depth of ~1.5 μm from the irradiated surface. Sub-surface microstructural damage and the chemical redistribution were characterized by transmission electron microscopy and energy dispersive spectroscopy, respectively. Irrespective of the layer thicknesses, the irradiation condition caused layer instability and the extent of damage varied with the dose levels. Doses lesser than ~60 dpa caused layer fragmentation and greater than ~60 dpa resulted in layer dissolution. The chemical mixing of layers occur to a depth of ~1 μm, consuming multiple bi-layer periods. Despite the elevated irradiation temperature (500 °C) and a slightly positive heat of mixing (+6 kJ/mol), no phase separation was observed and single-phase was retained in the mixed region. The results demonstrate that chemical mixing was facilitated by the liquid phase miscibility of Zr and Nb, which propelled the interdiffusion within the thermal spikes towards mixing.

36 MATERIALS SCIENCE↗

Evaluation of the interaction between SiC, pre-oxidized FeCrAlMo with aluminized and pre-oxidized Fe-8Cr-2W in flowing PbLi

We report dissimilar materials interactions are a major concern when liquid metals are used as a working fluid. To simulate a dual-coolant PbLi blanket, chemical vapor deposited (CVD) SiC, pre-oxidized FeCrAlMo (APMT) and pre-oxidized aluminized coating on Fe-8Cr-2 W (F82H) specimens were exposed to flowing commercial Pb-17at.%Li with a peak temperature of 650 °C in a pre-oxidized APMT thermal convection loop (TCL) for 1000 h. Similar to prior results in static PbLi, the coated F82H showed small mass changes and limited degradation of room-temperature tensile properties. After exposure, the α-Al 2 O 3 on the surface coated F82H reacted with the PbLi to form LiAlO 2 . However, no significant Al coating loss or interdiffusion was observed. Mass transfer was observed between the APMT, TCL and the SiC specimens. Fe, Cr and Ni were dissolved into the molten flowing PbLi and transported through the TCL to react with the SiC specimens. Compared to a prior experiment with a majority of bare FeCrAl specimens that were exposed in a TCL with a peak temperature of 700 °C for 1000 h, the SiC reaction was reduced to only a few microns of carbides and silicides. Oxygen dissolved in the molten PbLi sustained the formation of an Al 2 O 3 scale on the surface of the coating and induced the formation of a thin surface SiO 2 layer on the surface of the SiC.

36 MATERIALS SCIENCE↗

First-principles investigation of lanthanides diffusion in HCP zirconium via vacancy-mediated transport

The diffusion of lanthanide fission products plays an important role in the growth of the fuel-cladding chemical interaction (FCCI) region in metallic fuels. The use of a Zr interdiffusion barrier may mitigate the transport of lanthanides from the fuel to the cladding, but the efficacy of such a liner is not yet known. In this paper, the stability and vacancy-mediated diffusion of La, Ce, Pr, and Nd in hexagonal close-packed (HCP) Zr is investigated via density functional theory (DFT) calculations and self-consistent mean field (SCMF) analysis. DFT is used to calculate the formation, binding, and migration energies of vacancies and vacancy-solute pairs. The DFT energetics are used in the KineCluE code to calculate the Onsager transport coefficients. La is found to be the fastest diffusing species in HCP Zr and experiences an almost isotropic diffusion behavior. The other three species (Ce, Pr, and Nd) demonstrate anisotropic diffusion where the diffusion in the basal planes is significantly faster than that along the c-axis. Further, the calculated lanthanide diffusivities in HCP Zr are fitted to an Arrhenius relation and the activation energies and prefactors are reported for the first time. Furthermore, the vacancy drag and the segregation tendencies were analyzed using the calculated off-diagonal transport coefficients. According to our vacancy-mediated diffusion model, lanthanides are expected to be enriched at vacancy sinks at low temperatures, while at high temperatures, lanthanides are depleted at sinks and will preferably diffuse into the bulk. The enrichment/depletion transition temperature depends on the diffusion direction (basal or axial) and hence will be controlled by the grain texture and orientation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-temperature transport properties, thermal expansion and cathodic performance of Ni-substituted LaSr{sub 2}Mn{sub 2}O{sub 7-{delta}}

The substitution of manganese with nickel in LaSr{sub 2}Mn{sub 2}O{sub 7-{delta}}, where the solubility limit corresponds to approximately 25% Mn sites, enhances the Ruddlesden-Popper phase stability at elevated temperatures and atmospheric oxygen pressure. The total conductivity of LaSr{sub 2}Mn{sub 2-y}Ni{sub y}O{sub 7-{delta}} (y=0-0.4) decreases with nickel additions, whilst the average thermal expansion coefficients calculated from dilatometric data in the temperature range 300-1370 K increase from (11.4-13.7)x10{sup -6} K{sup -1} at y=0 up to (12.5-14.4)x10{sup -6} K{sup -1} at y=0.4. The conductivity and Seebeck coefficient of LaSr{sub 2}Mn{sub 1.6}Ni{sub 0.4}O{sub 7-{delta}}, analyzed in the oxygen partial pressure range 10{sup -15}-0.3 atm at 600-1270 K, display that the electronic transport is n-type and occurs via a small polaron mechanism. Reductive decomposition is observed at the oxygen pressures close to Ni/NiO boundary, namely {approx}2.3x10{sup -11} atm at 1223 K. Within the phase stability domain, the electronic transport properties are essentially p(O{sub 2})-independent. The steady-state oxygen permeability of dense LaSr{sub 2}Mn{sub 1.6}Ni{sub 0.4}O{sub 7-{delta}} membranes is higher than that of (La,Sr)MnO{sub 3-{delta}}, but lower if compared to perovskite-like (Sr,Ce)MnO{sub 3-{delta}}. Porous LaSr{sub 2}Mn{sub 1.6}Ni{sub 0.4}O{sub 7-{delta}} cathodes in contact with apatite-type La{sub 10}Si{sub 5}AlO{sub 26.5} solid electrolyte exhibit, however, a relatively poor electrochemical performance, partly associated with strong cation interdiffusion between the materials. - Graphical abstract: The substitution of manganese with nickel in Ruddlesden-Popper-type LaSr{sub 2}Mn{sub 2}O{sub 7-{delta}}, where the solubility limit corresponds to approximately 25% Mn sites, increases phase stability at elevated temperatures and thermal expansion, and decreases unit cell volume and total conductivity. The Seebeck coefficient and conductivity of LaSr{sub 2}Mn{sub 1.6}Ni{sub 0.4}O{sub 7-{delta}}, analyzed in the oxygen partial pressure range 10{sup -15}-0.3 atm at 600-1270 K, display that the electronic transport is n-type and occurs via a small polaron mechanism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structures, spectroscopic studies and solid-state thermal transformations of coordination polymers from P{sub 4}Se{sub 3} and CuX (X=Cl, Br, I)

The formation of coordination polymers (CuCl)P{sub 4}Se{sub 3} (1), (CuBr){sub 3}(P{sub 4}Se{sub 3}){sub 2} (2), (CuI){sub 3}(P{sub 4}Se{sub 3}){sub 2} (3) and (CuI)P{sub 4}Se{sub 3} (4), from solutions of copper(I) halides and P{sub 4}Se{sub 3} by diffusion methods has been studied. The new compounds were characterized by X-ray crystallography, solid-state {sup 31}P MAS NMR and Raman spectroscopy. Theoretical studies on the DFT level in the crystalline phase allowed the unequivocal assignment of the recorded Raman shifts between 200 and 480 cm{sup -1}. The structure of 1 consists of a 2D network of castellated [CuCl]{sub n} chains and bidentate P{sub 4}Se{sub 3} molecules. The 3D network of 2 comprises [CuBr]{sub n} chains, which are linked by tridentate P{sub 4}Se{sub 3} molecules. Compound 3 is a three-dimensional polymer composed of four-membered (CuI){sub 2} rings and castellated [CuI]{sub n} chains, which are linked by tridentate P{sub 4}Se{sub 3} molecules involving two basal and the apical P atoms. Thermal conversion of 1 at 230 deg. C gives (CuCl){sub 3}(P{sub 4}Se{sub 3}){sub 2} (5), which is isostructural with 2. The thermal conversion of (CuI){sub 3}P{sub 4}S{sub 3}, which was studied for comparison gave at 371 deg. C (CuI){sub 3}P{sub 4}S{sub 4}, Cu{sub 3}PS{sub 4} and small amounts of Cu{sub 6}PS{sub 5}I. - Graphical Abstract: New coordination polymers have been prepared and characterized by the reaction of P{sub 4}Se{sub 3} and copper(I) halides solutions under diffusion conditions. Highlights: > Coordination polymers from P{sub 4}Se{sub 3} and copper(I) halide are described. > Solid-state phases are prepared from solution by interdiffusion techniques. > One-, two- and three-dimensional polymers are formed. > Up to three P atoms are involved in coordination to copper. > Application of {sup 31}P MAS NMR spectroscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Self-assembly of designed precursors: A route to crystallographically aligned new materials with controlled nanoarchitecture

Modulated elemental reactants is a method by which new and complex intergrowth compounds can be synthesized by the self-assembly of designed precursors prepared by physical vapor deposition. Careful calibration of the composition and thickness of the precursors ensures the formation of the desired product by precise control of local composition and diffusion lengths. Superstructures of increasing complexity can be realized using binary and ternary systems as starting points. The synthesis of systems based on three different binary compounds, either alloyed together or separated into distinct layers, expands the number of possible superstructures that can be formed using this technique, but provides analytical challenges. The synthesis of [(SnSe){sub 1.15}]{sub 1}([Ta{sub x}V{sub 1−x}]Se{sub 2}){sub 1}[(SnSe){sub 1.15}]{sub 1}([V{sub y}Ta{sub 1−y}]Se{sub 2}){sub 1} compound is used to illustrate the preparation of precursors and the challenges in both measuring and limiting the interdiffusion of layers during self-assembly. Systematic changes in the electrical properties of (SnSe){sub 1+δ}(Ta{sub x}V{sub 1−x})Se{sub 2} alloys are observed as x is varied. The electrical resistivity of [(SnSe){sub 1.15}]{sub 1}([Ta{sub x}V{sub 1−x}]Se{sub 2}){sub 1}[(SnSe){sub 1.15}]{sub 1}([V{sub y}Ta{sub 1−y}]Se{sub 2}){sub 1} can be modeled as the two constituent layers in parallel.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electron microscopy characterization of an as-fabricated research reactor fuel plate comprised of U-7Mo particles dispersed in an Al-2Si alloy matrix

To understand the microstructural development of nuclear fuel plates during irradiation, it is imperative to know the microstructure of a fuel plate after all the fabrication steps have been completed and before it is inserted into the reactor. To this end, a U-7 wt.% Mo alloy research reactor dispersion fuel plate with Al-2 wt.% Si matrix was destructively examined using scanning and transmission electron microscopy to characterize the developed microstructure after fabrication. Of particular interest for this study was how the Si that was added to the fuel matrix partitioned between the various fuel plate phases during fabrication. Si was added to the matrix so that the microstructure that developed during fuel fabrication would exhibit good irradiation behavior. SEM analysis was used to identify the representative microstructure, the compositions of the various phases, and the partitioning behavior of the fuel and matrix constituents. TEM analysis was employed to definitively identify the phases in the U-7Mo alloy and the phases that formed due to diffusional interactions between the fuel particles and matrix during fuel plate fabrication. The TEM results are the first reported for an as-fabricated U-7 wt.% Mo dispersion fuel plate with an Al alloy matrix. SEM results showed that a significant portion of the original {gamma}-(U-Mo) fuel particles had transformed to a lamellar microstructure, comprised of {alpha}-U and either {gamma} or {gamma}' phases, and the fuel/matrix interaction layers were enriched in Si. TEM analysis identified an ordered fcc (U-Mo)(Al-Si){sub 3} type of phase, which formed at the decomposed U-7Mo/matrix interface and extended into the lamellar microstructure. Some regions of the U-7Mo particles retained the single-phase {gamma}-(U-Mo). Small precipitate phases were observed in the fuel meat matrix that contained Fe, Al, and Si. The Si that is added to the matrix of a U-Mo dispersion fuel plate to improve irradiation performance appears to result in the creation of a Si-rich (U-Mo)(Al-Si){sub 3} type of fuel/matrix interaction layer during fabrication that appears to exhibit favorable behavior during irradiation compared to the behavior of the layers that form in U-Mo dispersion fuel plates without Si in the matrix. - Research Highlights: {yields}Si seems to positively affect the microstructure of an as-fabricated fuel plate. {yields}Si modifications to the fuel plate exhibit favorable performance during irradiation. {yields}Si interdiffuses faster than Al.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Investigation of Cu coatings deposited by kinetic metallization

Interfacial characterisation of Kinetic Metallization (KM) sprayed Cu coatings applied on metal substrates was performed using optical and electron microscopy, as well as microindentation hardness testing and microchemical analysis. The interfacial characterisation of KM coatings remains scarce to date. Cross sectional observations of KM coatings on light metal substrates revealed an undulating, patelliform profile with thin-lipped cusps at the interface. Pure Al and Mg substrates exhibited a mechanically impinged zone <{approx}5 {mu}m on the substrate material, approximately the size of deformed Cu powder particles. Examination of the Cu side of the interface indicated there was no long range interaction in the coating. On the substrate side of the interface, the KM process induced phase transformations (i.e. recrystallisation and an alloyed zone) in thin layers contiguous to the interface on pure Al and Mg substrates. Zones of elemental interdiffusion were identified at the interface upon Al and Mg substrates using scanning TEM. The width of intermixing zones was in the vicinity of < 1 {mu}m. This metallurgical interaction at the interface occurred on the length scales involving the initial single layer of Cu particles bonded on the substrate.

36 MATERIALS SCIENCE↗

Microstructural study of transient liquid phase bonded DD98 and K465 superalloys at high temperature

Microstructure of a transient liquid phase (TLP) bonded joint between single crystal DD98 and polycrystalline K465 superalloys was investigated by scanning electron microscopy, transmission electron microscopy and X-ray diffraction techniques. After bonding at 1190 deg. C for 2 h, many phases formed in the centerline of the bonding zone due to an incompletely solidified liquid interlayer. There are script-like, tree-like and blocky compounds besides solid solution {gamma} phase in this region. The script-like phase is CrB boride that is rich in Cr, the tree-like compound rich in Ni is M{sub 23}B{sub 6} with FCC structure, and the blocky phase enriched in Ti, Ta, and Nb, is MC carbide that resulted from the interdiffusion of C atoms between dissimilar base metals. After TLP bonding, many blocky and fine M{sub 6}C particles rich in Cr and W appeared in the diffusion zone of the K465 side. A number of blocky and platelet M{sub 3}B{sub 2} borides rich in W, Cr and Mo precipitated in the diffusion zone of the DD98 side. - Research Highlights: {yields} DD98 and K465 alloy was TLP bonded. {yields} The microstructure changes of different parts were studied. {yields} CrB, M{sub 23}B{sub 6} and MC formed in the bonding zone. {yields} M{sub 6}C appeared in diffusion zone of K465 side and M{sub 3}B{sub 2} existed in diffusion zone of DD98 side.

36 MATERIALS SCIENCE↗

Influence of annealing conditions on the formation of hollow Al{sub 2}O{sub 3} microspheres studied by in situ ESEM

The transformation of Al microparticles into hollow and broken Al{sub 2}O{sub 3} microspheres was investigated by in situ environmental scanning electron microscopy (ESEM) up to 1150 °C under different heating rates and 120 Pa of gas atmospheres. Slow heating rates (2 °C min{sup −1}) resulted in a better coverage of the particles shell than with fast heating rates (20 °C min{sup −1}) that delayed the threshold temperature at which the particles opened. Above this threshold, the amount of opened spheres increased with heating rate, with the coarser particles opening more than the small ones. It appeared that inert atmospheres (He–4%H{sub 2}) increased the temperature at which the particles transformed, while air and pure oxygen tended to lower it. In contrast, the temperature interval was larger and was size-dependent when using water vapour. Irrespective of the gas atmosphere, opening of the spheres allowed molten Al to flow out from the core and aluminise the substrate while leaving behind a top coat of hollow alumina spheres. - Graphical abstract: (a) Effect of the increasing of oxidizing power of the gas atmosphere and of the heating rate. The former provokes in a better surface coverage of the Al microparticles while the latter results in thinner alumina shells. (b) The supply of Al to the substrate and the interdiffusion mechanisms result in an aluminised layer underneath the top coat of Al microparticles. - Highlights: • Transformations of Al microparticles with temperature demonstrated by in-situ SEM • The gas atmospheres changed the temperature of transformation of the Al microparticles. • The Al supply from the microparticles aluminized the superalloy substrate. • A potential thermal barrier coating was thus obtained in a single step process.

36 MATERIALS SCIENCE↗

New insights on the formation of supersaturated Cu-Nb solid solution prepared by mechanical alloying

The deformation-driven alloying mechanisms in the immiscible Cu-Nb system during mechanical alloying (MA) process have been studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high-resolution TEM (HRTEM) observations. It is found that the dominating alloying mechanism changes at the different stages of milling. Initially, the alloying process is mainly governed by interfaces and dislocations, which supply fast diffusion channels between phases. In the intermediate stage, Nb particles with sizes below 8 nm undergo a bcc to fcc allotropic transformation, and the interdiffusion between fcc-Nb and fcc-Cu is promoted due to the similarity of lattice structures. Further milling generates disclination defects, which contribute to the formation of fragments or subgrains with sizes below 5 nm. The introduction of such defects and fragments benefits the formation of a complete Cu-Nb solid solution. The formation kinetics of solid solution is analyzed by Johnson-Mehl-Avrami equation, which suggests that the speed of the diffusion of Nb atoms into Cu is very slow. - Highlights: •The bcc to fcc transformation in Nb nanoparticles promotes diffusion process. •The formation of fragments with sizes below 5 nm is attributed to the disclination defects. •Defect-assisted diffusion is responsible for the alloying process.

36 MATERIALS SCIENCE↗

Effects of carbon content and size on Ti-C reaction behavior and resultant properties of Cu-Ti-C alloy system

Highlights: • TiC-strengthened Cu alloys were synthesized by an in situ powder metallurgy route. • Effect of C/Ti ratio on electrical and mechanical properties was studied. • Ti-C reaction behavior during powder metallurgy process was discussed. • Microstructure evolution during present process was analyzed. - Abstract: TiC-strengthened Cu alloys with various nominal compositions were prepared by a high-energy ball-milling process, followed by consolidation using spark plasma sintering (SPS), and a subsequent heat treatment. The results indicated that the lower atomic ratio of C/Ti, the more residual Ti in copper matrix, resulting in a lower electrical conductivity but higher microhardness of alloy. The optimal atomic ratio was found to be close to1.0. The reaction behavior of Ti-C in the Cu-Ti-C system during this process was investigated. Microstructural results suggested that TiC formation is through a diffusion-controlled mechanism. A thin TiC layer was formed at the surface of C particles, and the growth of TiC layer was controlled by interdiffusion of C and Ti atoms across the TiC layer. An incomplete chemical reaction between Ti and C, characterized by a core-shell structure, was observed when the initial C particles were large, and the TiC particle size was found to strongly depending on the C particle size.

36 MATERIALS SCIENCE↗

Synthesis of porous Ti–50Ta alloy by powder metallurgy

Highlights: • The proposed preview milling with the next sintering enables the homogeneous porous Ti50Ta (wt).% alloy to be obtained • The α and β nanocrystalline phases were prepared by ball milling. • For the longest sintering time there is complete diffusion of preview milled initial powders • The press and sinter route is proved to be a promising alternative for melted Ti-based biomaterials. - Abstract: The aim of the present study was to assess the possibility of producing porous Ti50Ta (wt%) alloys using powder metallurgy by characterizing the material properties. The influence of the sintering time on the microstructure, mechanical properties, and corrosion behaviour of the produced alloy was investigated. The samples were examined using scanning electron microscopy (SEM), transmission electron microscopy (TEM), optic microscopy, X-ray diffraction (XRD) and nanoindentation methods. The XRD results confirmed that nanocrystalline α and β phases were formed during high-energy ball milling. A longer sintering time of 72 h allowed complete interdiffusion of the elements in the pre-milled initial powders. The sintering time significantly influenced the microstructure and porosity. Additionally, the corrosion resistance of the Ti-Ta samples in Ringer's solution was characterized and differences were observed between the samples sintered at different temperatures. The open-circuit potential (E{sub OCP}) and the corrosion potential (E{sub CORR}) of all samples were similar. The sintered Ti50Ta (wt%) alloy showed better corrosion resistance than equivalent Ti or Ta reference samples. We concluded that these alloys had suitable properties for medical implant applications in the future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Interface characteristics of Ti6Al4V-TiAl metal-intermetallic laminate (MIL) composites prepared by a novel hot-pack rolling

Highlights: • The Ti6Al4V/high Nb-TiAl metal-intermetallic (MIL) composite was fabricated. • The formation of γ and α{sub 2} phase at interface is diffusion controlled. • The formation of O phase at interface is due to the segregation of Nb atoms. • The Vickers hardness from Ti6Al4V to TiAl alloy shows a trend of a decrease then an increase and finally a decrease. - Abstract: Ti6Al4V (wt%)/Ti-44Al-8Nb-0.2W-0.2B-0.03Y (at.%) (high Nb-TiAl) metal–intermetallic laminate (MIL) composite with a defect-free interface was successfully prepared by hot-pack rolling and the interface microstructure was characterized by XRD, SEM, EBSD, and TEM techniques. The results showed that the interface was about 260 μm thick and consisted of four different microstructure regions. The thickness of each region was about 60–80 μm and the microstructure of the four regions consisted of acicular O, α{sub 2}, and β/B2 phases; acicular α{sub 2} phase; acicular α{sub 2} and β/B2 phases; and acicular γ, α{sub 2}, and β/B2 phases respectively. The resulting microstructure of the interface region was attributed to the interdiffusion of Ti atoms from the starting Ti6Al4V alloy layer to the high Nb-TiAl alloy layer and Al and Nb atoms from the high Nb-TiAl alloy layer to the Ti6Al4V alloy layer. The formation of acicular α{sub 2} and γ phases was diffusion-controlled and the Nb segregation at the interface caused the formation of O phase which had specific relationships with α{sub 2} and β/B2 phases. The detailed interface microstructural evolution of the Ti6Al4V/high Nb-TiAl MIL composite and the Vickers hardness of the composite are also discussed in this paper.

36 MATERIALS SCIENCE↗

Direct diffusion bonding of Ti{sub 3}SiC{sub 2} and Ti{sub 3}AlC{sub 2}

Two typical layered ternary compounds, Ti{sub 3}SiC{sub 2} and Ti{sub 3}AlC{sub 2}, were joined directly by solid-state diffusion bonding method. By various bonding tests at 1100-1300 deg. C for 30-120 min under 10-30 MPa, and characterizing the microstructure and diffusion reactive phases of the joints by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDS), transmission electron microscopy (TEM) and X-ray diffraction (XRD), the optimal condition for direct joining of Ti{sub 3}SiC{sub 2} and Ti{sub 3}AlC{sub 2} was obtained. Strong joints of Ti{sub 3}SiC{sub 2}/Ti{sub 3}AlC{sub 2} can be achieved via diffusion bonding, which is attributed to remarkable interdiffusion of Si and Al at the joint interface. The shear strength of the Ti{sub 3}SiC{sub 2}/Ti{sub 3}AlC{sub 2} joints was determined.

36 MATERIALS SCIENCE↗

Structure and microwave dielectric properties of Ba{sub 3}(VO{sub 4}){sub 2}–Zn{sub 2−x}SiO{sub 4−x} ceramic composites

Highlights: ► New Ba{sub 3}(VO{sub 4}){sub 2}–Zn{sub 1.87}SiO{sub 3.87} microwave dielectric composite ceramic was reported. ► The single-phase willemite was obtained by controlling of ZnO deficiency. ► The composite with 40 wt% Zn{sub 1.87}SiO{sub 3.87} exhibited excellent τ{sub f} value of 0.4 ppm/°C. - Abstract: Microwave dielectric ceramic composites with compositions of (1 − y)Ba{sub 3}(VO{sub 4}){sub 2}–yZn{sub 2−x}SiO{sub 4−x} (y = 0.4–0.6, x = 0.13) have been prepared by firing mixtures of Ba{sub 3}(VO{sub 4}){sub 2} and Zn{sub 1.87}SiO{sub 3.87}. The X-ray diffraction (XRD) analysis revealed that Zn{sub 2}SiO{sub 4} with a willemite phase can be obtained by appropriately controlling the ZnO deficiency. The starting Zn{sub 1.87}SiO{sub 3.87} powder should be thus composed of the ZnSiO{sub 4} crystal phase and redundant SiO{sub 2} amorphous phase at room temperature. The scanning electron microscopy studies demonstrated the coexistence of Zn{sub 2}SiO{sub 4} and Ba{sub 3}(VO{sub 4}){sub 2} phases in the sintered bodies, as further confirmed by the XRD and Raman results. The near-zero temperature coefficients of the resonant frequency (τ{sub f}) could be achieved by adjusting the relative content of the two phases owing to their opposite τ{sub f} values. The existence of a slight amount of secondary phases, element interdiffusion and non-stoichiometry such as Zn deficiency altogether made the predicted property values deviate from the experimentally measured ones. The composite ceramics with 40 wt% Zn{sub 1.87}SiO{sub 3.87} sintered at 1100 °C exhibited desirable microwave dielectric properties of the quality factor Q × f ∼ 23,000 GHz, dielectric constant ε{sub r} ∼ 9.3, and τ{sub f} ∼ 0.4 ppm/°C.

36 MATERIALS SCIENCE↗

Ti{sub 2}AlN thin films synthesized by annealing of (Ti+Al)/AlN multilayers

Highlights: • Epitaxial thin films of the MAX phase Ti{sub 2}AlN are obtained by thermal annealing. • A new metastable (Ti,Al,N) solid solution with the structure of α-T is evidenced. • The formation of the MAX phase occurs at low temperature (600 °C). - Abstract: Single-phase Ti{sub 2}AlN thin films were obtained by annealing in vacuum of (Ti + Al)/AlN multilayers deposited at room temperature by magnetron sputtering onto single-crystalline (0001) 4H-SiC and (0001) Al{sub 2}O{sub 3} substrates. In-situ X-ray diffraction experiments combined with ex-situ cross-sectional transmission electron microscopy observations reveal that interdiffusion processes occur in the multilayer at a temperature of ∼400 °C leading to the formation of a (Ti, Al, N) solid solution, having the hexagonal structure of α-Ti, whereas the formation of Ti{sub 2}AlN occurs at 550–600 °C. Highly oriented (0002) Ti{sub 2}AlN thin films can be obtained after an annealing at 750 °C.

36 MATERIALS SCIENCE↗