Search NASA⌕ Search

SEARCH · Search NASA

Results for “interface reinforcement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Thermomechanical Fatigue Damage/Failure Mechanisms in SCS-6/Timetal 21S [0/90](Sub S) Composite

The thermomechanical fatigue (TMF) deformation, damage, and life behaviors of SCS6/Timetal 21S (0/90)s were investigated under zero-tension conditions. In-phase (IP) and out-of-phase (OP) loadings were investigated with a temperature cycle from 150 to 650 deg C. An advanced TMF test technique was used to quantify mechanically damage progression. The technique incorporated explicit measurements of the macroscopic (1) isothermal static moduli at the temperature extremes of the TMF cycle and (2) coefficient of thermal expansion (CTE) as functions of the TMF cycles. The importance of thermal property degradation and its relevance to accurate post-test data analysis and interpretation is briefly addressed. Extensive fractography and metallography were conducted on specimens from failed and interrupted tests to characterize the extent of damage at the microstructure level. Fatigue life results indicated trends analogous to those established for similar unidirectional(0) reinforced titanium matrix composite systems. High stress IP and mid to low stress OP loading conditions were life-limiting in comparison to maximum temperature isothermal conditions. Dominant damage mechanisms changed with cycle type. Damage resulting from IP TMF conditions produced measurable decreases in static moduli but only minimal changes in the CTE. Metallography on interrupted and failed specimens revealed extensive (0) fiber cracking with sparse matrix damage. No surface initiated matrix cracks were present. Comparable OP TMF conditions initiated environment enhanced surface cracking and matrix cracking initiated at (90) fiber/matrix (F/M) interfaces. Notable static moduli and CTE degradations were measured. Fractography and metallography revealed that the transverse cracks originating from the surface and (90) F/M interfaces tended to converge and coalesce at the (0) fibers.

Castelli, Michael G.↗
NASA NTRS1995

CVD silicon carbide monofilament reinforced SrO-Al2O3-2SiO2 (SAS) glass-ceramic composites

Unidirectional CVD SiC fiber-reinforced SrO.Al2O3.2SiO2 (SAS) glass-ceramic matrix composites have been fabricated by hot pressing at various combinations of temperature, pressure and time. Both carbon-rich surface coated SCS-6 and uncoated SCS-0 fibers were used as reinforcements. Almost fully dense composites have been obtained. Monoclinic celsian, SrAl2Si2O8, was the only crystalline phase observed in the matrix from x-ray diffraction. During three point flexure testing of composites, a test span to thickness ratio of approximately 25 or greater was necessary to avoid sample delamination. Strong and tough SCS-6/SAS composites having a first matrix crack stress of approximately 300 MPa and an ultimate bend strength of approximately 825 MPa were fabricated. No chemical reaction between the SCS-6 fibers and the SAS matrix was observed after high temperature processing. The uncoated SCS-0 fiber-reinforced SAS composites showed only limited improvement in strength over SAS monolithic. The SCS-0/SAS composite having a fiber volume fraction of 0.24 and hot pressed at 1400 deg C exhibited a first matrix cracking stress of approximately 231 +/- 20 MPa and ultimate strength of 265 +/- 17 MPa. From fiber push-out tests, the fiber/matrix interfacial debonding strength (tau(sub debond)) and frictional sliding stress (tau(sub friction)) in the SCS-6/SAS system were evaluated to be approximately 6.7 +/- 2.3 MPa and 4.3 +/- 0.6 MPa, respectively, indicating a weak interface. However, for the SCS-0/SAS composite, much higher values of approximately 17.5 +/- 2.7 MPa for tau(sub debond) and 11.3 +/- 1.6 MPa for tau(sub friction) respectively, were observed; some of the fibers were so strongly bonded to the matrix that they could not be pushed out. Examination of fracture surfaces revealed limited short pull-out length of SCS-0 fibers. The applicability of various micromechanical models for predicting the values of first matrix cracking stress and ultimate strength of these composites were examined.

Bansal, Narottam P.↗
NASA NTRS2005

Mechanical Properties of Nanostructured Materials Determined Through Molecular Modeling Techniques

The potential for gains in material properties over conventional materials has motivated an effort to develop novel nanostructured materials for aerospace applications. These novel materials typically consist of a polymer matrix reinforced with particles on the nanometer length scale. In this study, molecular modeling is used to construct fully atomistic models of a carbon nanotube embedded in an epoxy polymer matrix. Functionalization of the nanotube which consists of the introduction of direct chemical bonding between the polymer matrix and the nanotube, hence providing a load transfer mechanism, is systematically varied. The relative effectiveness of functionalization in a nanostructured material may depend on a variety of factors related to the details of the chemical bonding and the polymer structure at the nanotube-polymer interface. The objective of this modeling is to determine what influence the details of functionalization of the carbon nanotube with the polymer matrix has on the resulting mechanical properties. By considering a range of degree of functionalization, the structure-property relationships of these materials is examined and mechanical properties of these models are calculated using standard techniques.

Clancy, Thomas C.↗
NASA NTRS1990

Effect of interleaves on fracture of laminated composites. I - Analysis. II - Solution and results

The effect of interleaves placed between the fiber-reinforced plies of multilayered composite laminates is investigated analytically, with the composite approximated by linearly elastic isotropic media consisting of half-planes separated from a finite-width layer by thin interleaves of low extensional and shear moduli. Integral equations are derived which describe the effect of interleaves on damage growth. Numerical solutions are then developed which are based on Gaussian integration techniques and Hadamard's concept of differentiation of Cauchy integrals. Critical stresses and displacements are calculated to investigate the influence of relative elastic properties and geometry of the interleafed composite on interface debonding, extent and suppression and delamination, and stress relieving in the undamaged plies.

Kaw, A. K.↗
NASA NTRS1992

Stress-strain analysis of a (0/90)sub 2 symmetric titanium matrix laminate subjected to a generic hypersonic flight profile

Cross ply laminate behavior of Ti-15V-3Cr-3Al-3Sn (Ti-15-3) matrix reinforced with continuous silicon carbide fibers (SCS-6) subjected to a generic hypersonic flight profile was evaluated experimentally and analytically. Thermomechanical fatigue test techniques were developed to conduct a simulation of a generic hypersonic flight profile. A micromechanical analysis was used. The analysis predicts the stress-strain response of the laminate and of the constituents in each ply during thermal and mechanical cycling by using only constituent properties as input. The fiber was modeled using a thermo-viscoplastic constitutive relation. The fiber transverse modulus was reduced in the analysis to simulate the fiber matrix interface failure. Excellent correlation was found between measured and predicted laminate stress-strain response due to generic hypersonic flight profile when fiber debonding was modeled.

Mirdamadi, Massoud↗
NASA NTRS2006

Oxidation Microstructure Studies of Reinforced Carbon/Carbon

Laboratory oxidation studies of reinforced carbon/carbon (RCC) are discussed with particular emphasis on the resulting microstructures. This study involves laboratory furnace (500-1500 C deg) and arc-jet exposures (1538 C deg) on various forms of RCC. RCC without oxidation protection oxidized at 800 and 1100 C deg exhibits pointed and reduced diameter fibers, due to preferential attack along the fiber edges. RCC with a SiC conversion coating exhibits limited attack of the carbon substrate at 500, 700 and 1500 C deg. However samples oxidized at 900, 1100, and 1300 C deg show small oxidation cavities at the SiC/carbon interface below through-thickness cracks in the SiC coating. These cavities have rough edges with denuded fibers and can be easily distinguished from cavities created in processing. Arc-jet tests at 1538 C deg show limited oxidation attack when the SiC coating and glass sealants are intact. When the SiC/sealant protection system is damaged, attack is extensive and proceeds through matrix cracks, creating denuded fibers on the edges of the cracks. Even at 1538 C deg, where diffusion control dominates, attack is non-uniform with fiber edges oxidizing in preference to the bulk fiber and matrix.

Jacobson, Nathan S.↗
NASA NTRS1992

Thermal conductance of two interface materials and their applications in space systems

The temperature control of spacecraft and instrument systems and subsystems requires heat transfer interface materials that possess good thermal and structural characteristics, among other properties, to respond to the vacuum environment of space. These materials must be easy to apply to, and remove from, the surfaces where they are applied, and must be able to withstand power dissipation extremes, and be used for different clamping configurations and pressures. Silicone based greases, used in the past, tend to migrate and to contaminate nearby surfaces. Bare metal to metal contact offers low thermal conductance and difficulties in estimating the actual heat transfer. Several polymeric materials containing different thermal conductive compounds and structural reinforcements were prepared to overcome grease and metal problems. Two polymeric materials were evaluated: Cho-Therm 1671 elastomer; and the CV-2946, a conductive RTV silicone. Tests were done to learn more about these products. Results indicate that the tightly bolted, torqued fixtures did not buckle or distort, and provided optimum thermal conductance. Fixtures simulating actual spacecraft configuration suffered bowing and separating.

Scialdone, J. J.↗
NASA NTRS2014

TPSAS-NF1676L-18913-DND

Composite materials and structures are enabling technology for modern aerospace vehicles. Numerical-control manufacturing, including automated fiber placement (AFP), is widely used to fabricate these components. However, weight and performance requirements for the next generation of aerospace vehicles will push the state-of-art even further, and require development of more advanced materials, manufacturing, and structures technologies that are both affordable and efficient. The Integrated Structural Assembly of Advanced Composites (ISAAC) system is intended to address much of NASA?s critical research needs in advanced composites. The baseline ISAAC system, combining a commercial robot with multiple redundant degrees of freedom, a tool changer interface, and a special-purpose AFP end effector, enables precise and accurate additive manufacturing of composite structures, as well as development of advanced tow-steered structures with tailored load paths. The highly capable baseline system can quickly change end effectors, thus enabling further research for composites manufacturing. This extended system is similar to a high-speed machining center, where interchangeable cutters are used for different operations during metal structures fabrication. This capability enables future development, integration and assessment of new advanced manufacturing technologies, such as in-situ curing and NDE, and through-thickness reinforcements to reduce delaminations. End effectors with these advanced capabilities may be purchased, developed internally or with industry or academia, and then integrated onto the existing robotic platform to perform advanced manufacturing operations and develop new techniques and processes. Technologies, techniques and processes developed using this research-oriented system could then be transitioned to the broader composites industry.

Rob Martin↗
NASA NTRS2002

Thermal Cyclic Behavior of Thermal and Environmental Barrier Coatings Investigated Under High-Heat-Flux Conditions

Environmental barrier coatings (EBC's) have been developed to protect silicon-carbide- (SiC) based ceramic components in gas turbine engines from high-temperature environmental attack. With continuously increasing demands for significantly higher engine operating temperature, future EBC systems must be designed for both thermal and environmental protection of the engine components in combustion gases. In particular, the thermal barrier functions of EBC's become a necessity for reducing the engine-component thermal loads and chemical reaction rates, thus maintaining the required mechanical properties and durability of these components. Advances in the development of thermal and environmental barrier coatings (TBC's and EBC's, respectively) will directly impact the successful use of ceramic components in advanced engines. To develop high-performance coating systems, researchers must establish advanced test approaches. In this study, a laser high-heat-flux technique was employed to investigate the thermal cyclic behavior of TBC's and EBC's on SiC-reinforced SiC ceramic matrix composite substrates (SiC/SiC) under high thermal gradient and thermal cycling conditions. Because the laser heat flux test approach can monitor the coating's real-time thermal conductivity variations at high temperature, the coating thermal insulation performance, sintering, and delamination can all be obtained during thermal cycling tests. Plasma-sprayed yttria-stabilized zirconia (ZrO2-8 wt% Y2O3) thermal barrier and barium strontium aluminosilicate-based environmental barrier coatings (BSAS/BSAS+mullite/Si) on SiC/SiC ceramic matrix composites were investigated in this study. These coatings were laser tested in air under thermal gradients (the surface and interface temperatures were approximately 1482 and 1300 C, respectively). Some coating specimens were also subject to alternating furnace cycling (in a 90-percent water vapor environment at 1300 C) and laser thermal gradient cycling tests (in air), to investigate the water vapor effect. All cyclic tests were conducted using a 60-min hot-time temperature.

Zhu, Dongming↗
NASA NTRS1997

Response of Composite Panels with Stiffness Gradients Due to Stiffener Terminations and Cutouts

The results of an analytical and experimental study of stiffened graphite-epoxy compression panels with terminated stiffeners are presented. The local stress gradients at the stiffener termination location are determined by finite element analysis. Three stiffener termination concepts are evaluated by analysis to determine the stiffener and skin laminate parameters that affect the panel response and failure. The effects of changing local skin laminate definitions, skin reinforcement details, and stiffener termination details on local stress gradients and load-path eccentricities are discussed. Analytical and test results are presented for panels with one terminated stiffener and for panels with one terminated stiffener and two unterminated stiffeners. The effects of a cutout in the skin of a panel with a terminated stiffener is also evaluated to determine the interaction between the stress gradients in the panel due to the cutout and those due to the terminated stiffener. The results of the study indicate that the critical failure modes of the panels initiate at the skin-stiffener interface near the end of the terminated stiffener.

Ambur, Damodar R.↗
NASA NTRS1992

Creep behavior of tungsten fiber reinforced niobium metal matrix composites

Tungsten fiber reinforced niobium metal matrix composites were evaluated for use in space nuclear power conversion systems. The composite panels were fabricated using the arc-spray monotape technique at the NASA Lewis Research Center. The creep behavior of W/Nb composite material was determined at 1400 and 1500 K in vacuum over a wide range of applied loads. The time to reach 1 percent strain, the time to rupture, and the minimum creep rate were measured. The W/Nb composites exceeded the properties of monolithic niobium alloys significantly even when compared creep strength also was evaluated. Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending the fiber orientation relative to the stress axis. A relationship was found between the fiber orientation and the creep strength.

Grobstein, Toni L.↗
NASA NTRS1977

Continuous and cyclic thermal exposure induced degradation in boron reinforced 6061 aluminum composites

Boron reinforced 6061 aluminum (B/Al) composite was continuously exposed at 728 K for up to 240 hours and cyclically exposed between 293 K and 728 K for up to 6000 three-minute cycles. Room temperature tensile strengths were measured and the specimens were metallographically examined. The data suggest that, in addition to AlB2 formation, magnesium in the matrix diffused to the reaction layer and formed (Al,Mg)B2. This formation could weaken the matrix and embrittle the reaction layer. Continuous exposure degraded the strength of the B/Al specimens about 28% in 240 hours. However, the fracture mode, one indicative of high strength interfaces, did not change. The strength degradation was attributed to crack initiation in the brittle reaction layer causing stress concentrations in the fibers. Cyclic exposure degraded the strength of the B/Al about 34% in 6000 cycles. The fracture mode of the cyclic exposure specimens showed transition toward a mode characteristic of low interfacial strength. The lower interfacial strengths were attributed to stress fields induced by differential thermal expansion. Cyclic exposure degraded the strength of the B/Al specimens more than continuous exposure for similar cumulative exposure times.

Olsen, G. C.↗
NASA NTRSDate not supplied

Realistic Thermographic Simulation of Impact Damage with Quadrupole Method

Flash thermography has been shown to be an effective method for detection of delaminations in carbon fiber reinforced polymer (CFRP) composite structures. Improved understanding of thelimitations of the technique can be obtained by simulating the inspection process. Time domainfinite difference and finite element methods are well suited for such simulations but can be computationally intensive. An alternate method is to solve the Laplace transform of the heat equation, then invert the Laplace transform to produce a time domain response. Often this is referred to as the thermal quadrupole method and is well suited for simulating flash thermography. The quadrupole method has been used extensively for simulating one-dimensional heat flow in multilayer systems with contact resistances at the interfaces. It is also applicable for three dimensional configurations, in particular for simulation of changes in thermographic response due to delaminations in composites. This presentation discusses three-dimensional simulations with realistic shapes and contact resistances at the interfaces between layers. The results of these simulations are compared to thermography measurements on composites specimens with impact induced delaminations.

Thermography↗
NASA NTRS1989

Effects of aging condition on the fracture toughness of 2XXX and 7XXX series aluminum alloy composites

Results are presented on the effects of matrix aging condition (i.e., matrix temper) on the fracture toughness of 2XXX and 7XXX Al matrix alloys reinforced with SiC particulates, and the results are compared with the mechanical behavior. Fracture toughness testing was conducted on fatigue precracked bend specimens, and fracture surfaces were examined using SEM. Results revealed dramatic differences in the effect of matrix microstructure on the fracture properties of the two composite series. In the 7XXX material, the toughness values decreased from the underaged (UA) condition to the overaged (OA) condition by approximately 40 percent, while in the 2XXX series composite, the effect of matrix microstructure was marginal. In the 7XXX series composites, a transition in fracture mode from particle cracking (in UA) to matrix and linear-interface failure (in OA) was observed, while the 2XXX series composite failed predominantly by particle cracking.

Manoharan, M.↗
NASA NTRS1990

Characterization of unnotched SCS-6/Ti-15-3 metal matrix composites at 650 C

Ti-15-3 reinforced with SCS-6 silicon carbide fibers, in five different layups, was tested at 650 C to determine monotonic and fatigue strengths, basic mechanical properties, and damage initiation and progression. The elevated temperature results were compared to those obtained at room temperature. Analytical predictions were made of the monotonic stress-strain response as well as cyclic stress-strain hysteresis. The fiber reinforcement was found to significantly increase the static and fatigue strengths of the laminates over that of the matrix material at elevated temperature while the increase was insignificant at room temperature. Initial damage, in either the fibers or the matrix, was partitioned as a function of the life and applied strain range in the constituents. High strains and short lives resulted in multiple fiber failure with no signs of matrix fatigue cracking. Low strains and long lives resulted in extensive matrix cracking and no fiber breaks away from the fracture surface. At 650 C the matrix was too weak to cause fiber-matrix interface failure prior to matrix yielding. Laminate fatigue lives were hypothesized to be a function of the 0 deg fiber stress. More scatter was found in the 0 deg fiber stress vs. high temperature fatigue life data than for the room temperature data. An initial unloading modulus that was greater than the initial loading modulus was observed in the elevated temperature fatigue tests.

Pollock, W. D.↗
NASA NTRS1992

Pressure vessel flex joint

An airtight, flexible joint is disclosed for the interfacing of two pressure vessels such as between the Space Station docking tunnel and the Space Shuttle Orbiter bulkhead adapter. The joint provides for flexibility while still retaining a structural link between the two vessels required due to the loading created by the internal/external pressure differential. The joint design provides for limiting the axial load carried across the joint to a specific value, a function returned in the Orbiter/Station tunnel interface. The flex joint comprises a floating structural segment which is permanently attached to one of the pressure vessels through the use of an inflatable seal. The geometric configuration of the joint causes the tension between the vessels created by the internal gas pressure to compress the inflatable seal. The inflation pressure of the seal is kept at a value above the internal/external pressure differential of the vessels in order to maintain a controlled distance between the floating segment and pressure vessel. The inflatable seal consists of either a hollow torus-shaped flexible bladder or two rolling convoluted diaphragm seals which may be reinforced by a system of straps or fabric anchored to the hard structures. The joint acts as a flexible link to allow both angular motion and lateral displacement while it still contains the internal pressure and holds the axial tension between the vessels.

Kahn, Jon B.↗
NASA NTRS1992

Characterization of unnotched SCS-6/Ti-15-3 metal matrix composites at 650 C

Ti-15-3 reinforced with SCS-6 silicon carbide fibers, in five different layups, was tested at 650 C to determine monotonic and fatigue strengths, basic mechanical properties, and damage initiation and progression. The elevated temperature results were compared to those obtained at room temperature. Analytical predictions were made of the monotonic stress-strain response as well as cyclic stress-strain hysteresis. The fiber reinforcement was found to significantly increase the static and fatigue strengths of the laminates over that of the matrix material at elevated temperature while the increase was insignificant at room temperature. Initial damage, in either the fibers or the matrix, was partitioned as a function of the life and applied strain range in the constituents. High strains and short lives resulted in multiple fiber failure with no signs of matrix fatigue cracking. Low strains and long lives resulted in extensive matrix cracking and no fiber breaks away from the fracture surface. At 650 C the matrix was too weak to cause fiber-matrix interface failure prior to matrix yielding. Laminate fatigue lives were hypothesized to be a function of the 0 deg fiber stress. More scatter was found in the 0 deg fiber stress vs. high temperature fatigue life data than for the room temperature data. An initial unloading modulus that was greater than the initial loading modulus was observed in the elevated temperature fatigue tests.

Pollock, William D.↗
NASA NTRS2012

Design, Analysis and Fabrication of Secondary Structural Components for the Habitat Demonstration Unit-Deep Space Habitat

In support of NASA s Habitat Demonstration Unit - Deep Space Habitat Prototype, a number of evolved structural sections were designed, fabricated, analyzed and installed in the 5 meter diameter prototype. The hardware consisted of three principal structural sections, and included the development of novel fastener insert concepts. The articles developed consisted of: 1) 1/8th of the primary flooring section, 2) an inner radius floor beam support which interfaced with, and supported (1), 3) two upper hatch section prototypes, and 4) novel insert designs for mechanical fastener attachments. Advanced manufacturing approaches were utilized in the fabrication of the components. The structural components were developed using current commercial aircraft constructions as a baseline (for both the flooring components and their associated mechanical fastener inserts). The structural sections utilized honeycomb sandwich panels. The core section consisted of 1/8th inch cell size Nomex, at 9 lbs/cu ft, and which was 0.66 inches thick. The facesheets had 3 plys each, with a thickness of 0.010 inches per ply, made from woven E-glass with epoxy reinforcement. Analysis activities consisted of both analytical models, as well as initial closed form calculations. Testing was conducted to help verify analysis model inputs, as well as to facilitate correlation between testing and analysis. Test activities consisted of both 4 point bending tests as well as compressive core crush sequences. This paper presents an overview of this activity, and discusses issues encountered during the various phases of the applied research effort, and its relevance to future space based habitats.

Smith, Russell W.↗