Search NASA⌕ Search

SEARCH · Search NASA

Results for “ionic current”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

A Study on the Synthesis and Proton Transport Behavior of Multilayered ZSM-5 Zeolite Nanosheet Membranes Laminated on Polymer Substrates

Single crystalline ZSM-5 ZNs with thicknesses around 6 nm were obtained by secondary growth of silicalite nanoparticles using diquaternary bis-1,5(tripropyl ammonium) pentamethylene diiodide (dC5) as a structure-directing agent (SDA). The dC5 could be effectively removed from the ZN pores by either high-temperature calcination or UV irradiation in air at room temperature but not by the piranha solution treatment. Ultrathin ZN-laminated membranes (ZNLMs) were fabricated by sandwiching a UV-activated multilayered ZN film between two recast Nafion® layers (ZNLM-Nafion) and by filtration coating from a suspension of thermally activated ZNs on a nonionic porous PVDF (ZNLM-PVDF). The ZNLMs on both supports demonstrated the ability of highly proton-selective ion conduction with low resistances in aqueous electrolyte solutions. The ZNLM-PVDF with PVDF binder was structurally stable, and it achieved a comparably low ASR but much higher proton selectivity compared with a Nafion membrane of same overall thickness. However, detachment between the ZNLM and Nafion layers occurred when the ZNLM-Nafion operated in aqueous electrolyte solutions. Results of this study show the potential for developing ZNLMs as efficient proton-conducting membranes without using expensive ionic polymer matrices. However, the development of polymer-supported ZNLMs is hindered by the current inefficiency in preparing well-dispersed suspensions of open-pore ZNs. Future development of efficient methods for synthesizing open-pore ZNs in dispersed states is key to realizing high-performance ZNLMs on polymers.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Measuring the spacecraft and environmental interactions of the 8-cm mercury ion thrusters on the P80-1 mission

The subject interface measurements are described for the Ion Auxiliary Propulsion System (IAPS) flight test of two 8-cm thrusters. The diagnostic devices and the effects to be measured include: 1) quartz crystal microbalances to detect nonvolatile deposition due to thruster operation; 2) warm and cold solar cell monitors for nonvolatile and volatile (mercury) deposition; 3) retarding potential ion collectors to characterize the low energy thruster ionic efflux; and 4) a probe to measure the spacecraft potential and thruster generated electron currents to biased spacecraft surfaces. The diagnostics will also assess space environmental interactions of the spacecraft and thrusters. The diagnostic data will characterize mercury thruster interfaces and provide data useful for future applications.

Power, J. L.↗
NASA NTRS2010

Process to Produce Iron Nanoparticle Lunar Dust Simulant Composite

A document discusses a method for producing nanophase iron lunar dust composite simulant by heating a mixture of carbon black and current lunar simulant types (mixed oxide including iron oxide) at a high temperature to reduce ionic iron into elemental iron. The product is a chemically modified lunar simulant that can be attracted by a magnet, and has a surface layer with an iron concentration that is increased during the reaction. The iron was found to be -iron and Fe3O4 nanoparticles. The simulant produced with this method contains iron nanoparticles not available previously, and they are stable in ambient air. These nanoparticles can be mass-produced simply.

Hung, Ching-cheh↗
NASA NTRS2014

Lithium-Based High Energy Density Flow Batteries

Systems and methods in accordance with embodiments of the invention implement a lithium-based high energy density flow battery. In one embodiment, a lithium-based high energy density flow battery includes a first anodic conductive solution that includes a lithium polyaromatic hydrocarbon complex dissolved in a solvent, a second cathodic conductive solution that includes a cathodic complex dissolved in a solvent, a solid lithium ion conductor disposed so as to separate the first solution from the second solution, such that the first conductive solution, the second conductive solution, and the solid lithium ionic conductor define a circuit, where when the circuit is closed, lithium from the lithium polyaromatic hydrocarbon complex in the first conductive solution dissociates from the lithium polyaromatic hydrocarbon complex, migrates through the solid lithium ionic conductor, and associates with the cathodic complex of the second conductive solution, and a current is generated.

Bugga, Ratnakumar V.↗
NASA NTRS2021

Investigation of Ionic Liquids Isolated Iron for Ductile Iron Castings

As research continues for missions beyond low-Earth orbit, in-situ resource utilization (ISRU) methods are critical. For Lunar and Martian colonization, the ability to manufacture mechanical and structural components with local resources is essential. Ionic liquids (IL) are being studied at NASA Marshall Space Flight Center (MSFC) to harvest elemental metals from meteorites and regolith oxides. In this investigation, the viability of casting ductile iron using ionic liquids sourced iron and nickel was explored given ductile iron’s range of applications and performance as an as-cast alloy. Ingots were produced using commercial elements to simulate the use of IL iron with carbon sourced from the by-products of a life support system currently tested at MSFC. Samples were cast and compared to commercial ductile iron with phase transformation diagrams,microstructures, and hardness. Results showed ionic liquids sourced elements are a viable source of elemental alloying materials for a range of ductile iron alloys.

Ionic Liquids↗
DOE OSTI2020

Understanding resistances in capacitive deionization devices

The desalination characteristics of capacitive deionization (CDI) are significantly impacted by the cell resistance. Here we apply electrochemical impedance spectroscopy (EIS) to analyze the resistive properties of a CDI device, which include EIS measurements on a complete assembled cell (in two wire mode) and EIS measurements with additional contacts to decouple electrode/electrolyte and contact impedances (four wire mode). These measurements shed light on the interface between current collector and electrode as well as the internal capacitive and resistive elements of the cell. With two-wire and four-wire EIS measurements, we find that the often observed high-frequency arc(s) in the impedance spectra can be due to contact effects and/or an internal ionic-transfer resistance that is locally in parallel with macropore wall capacitance. In some cases, the two associated arcs in the Nyquist plot are overlapping and present simultaneously, making their identification in the EIS spectra difficult unless both two-wire and four-wire measurements are made. Despite causing a large high-frequency arc in the Nyquist plot, we find that the apparent internal ionic-transfer resistance is negligible compared to the resistances of the electrode, separator, and external electronic components. Here, an investigation of the contact impedance between the electrode and current collector reveals a parallel RC arc that can grow over time if an improper material is used (e.g., titanium). In our system, the electrode ionic resistance dominates the total Ohmic power dissipation, which has implications for scale-up of CDI systems and future improvements of cell design.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Investigation of Ionic Liquids Isolated Iron for Ductile Iron Castings

As research continues for missions beyond low-Earth orbit, in-situ resource utilization (ISRU) methods are critical. To colonize the Lunar or Martian surface, the ability to manufacture mechanical and structural components with local resources is essential. Ionic liquids are being studied at NASA Marshall Space Flight Center (MSFC) to harvest elemental metals from meteorites and oxides in regolith. In this investigation, the viability of casting ductile iron using ionic liquids sourced iron and nickel was explored given ductile iron’s range of applications and performance as an as-cast alloy. Small ingots were produced using commercial silicon, manganese, and magnesium with carbon sourced from the by-products of a life support system currently being tested at MSFC. Samples were cast and compared to commercial ductile iron with phase transformation diagrams, microstructures, and hardness. Results showed ionic liquids sourced elements are a viable source of elemental alloying materials for a range of ductile iron alloys.

Blake Stewart↗
DOE OSTI2024

Computational Advances in Ionic Liquid Applications for Green Chemistry: A Critical Review of Lignin Processing and Machine Learning Approaches

The valorization and dissolution of lignin using ionic liquids (ILs) is critical for developing sustainable biorefineries and a circular bioeconomy. This review aims to critically assess the current state of computational and machine learning methods for understanding and optimizing IL-based lignin dissolution and valorization processes reported since 2022. The paper examines various computational approaches, from quantum chemistry to machine learning, highlighting their strengths, limitations, and recent advances in predicting and optimizing lignin-IL interactions. Key themes include the challenges in accurately modeling lignin’s complex structure, the development of efficient screening methodologies for ionic liquids to enhance lignin dissolution and valorization processes, and the integration of machine learning with quantum calculations. These computational advances will drive progress in IL-based lignin valorization by providing deeper molecular-level insights and facilitating the rapid screening of novel IL-lignin systems.

09 BIOMASS FUELS↗
DOE OSTI2024

Influence of misfit dislocations on ionic conductivity at oxide interfaces

Mismatched complex oxide thin films and heterostructures have gained significant traction for use as electrolytes in intermediate temperature solid oxide fuel cells, wherein interfaces exhibit variation in ionic conductivity as compared to the bulk. Although misfit dislocations present at interfaces in these structures impact ionic conductivity, the fundamental mechanisms responsible for this effect are not well understood. To this end, a kinetic lattice Monte Carlo (KLMC) model was developed to trace oxygen vacancy diffusion at misfit dislocations in SrTiO 3 /BaZrO 3 heterostructures and elucidate the atomistic mechanisms governing ionic diffusion at oxide interfaces. The KLMC model utilized oxygen vacancy migration energy barriers computed using molecular statics. While some interfaces promote oxygen vacancy diffusion, others impede their transport. Fundamental factors such as interface layer chemistry, misfit dislocation structure, and starting and ending sites of migrating ions play a crucial role in oxygen diffusivity. Molecular dynamics (MD) simulations were further performed to support qualitative trends for oxygen vacancy diffusion. Overall, the agreement between KLMC and MD is quite good, though MD tends to predict slightly higher conductivities, perhaps a reflection of nuanced structural relaxations that are not captured by KLMC. The current framework comprising KLMC modeling integrated with molecular statics offers a powerful tool to perform mechanistic studies focused on ionic transport in thin film oxide electrolytes and facilitate their rational design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A High‐Rate Li–CO 2 Battery Enabled by 2D Medium‐Entropy Catalyst

Abstract Lithium‐air batteries based on CO 2 reactant (Li–CO 2 ) have recently been of interest because it has been found that reversible Li/CO 2 electrochemistry is feasible. In this study, a new medium‐entropy cathode catalyst, (NbTa) 0.5 BiS 3 , that enables the reversible electrochemistry to operate at high rates is presented. This medium entropy cathode catalyst is combined with an ionic liquid‐based electrolyte blend to give a Li–CO 2 battery that operates at high current density of 5000 mA g −1 and capacity of 5000 mAh g −1 for up to 125 cycles, far exceeding reported values in the literature for this type of battery. The higher rate performance is believed to be due to the greater stability of the multi‐element (NbTa) 0.5 BiS 3 catalyst because of its higher entropy compared to previously used catalysts with a smaller number of elements with lower entropies. Evidence for this comes from computational studies giving very low surface energies (high surface stability) for (NbTa) 0.5 BiS 3 and transmission electron microscopystudies showing the structure being retained after cycling. In addition, the calculations indicate that Nb‐terminated surface promotes Li–CO 2 electrochemistry resulting in Li 2 CO 3 and carbon formation, consistent with the products found in the cell. These results open new direction to design and develop high‐performance Li–CO 2 batteries.

25 ENERGY STORAGE↗
NASA NTRS1975

An auroral F-region study using in situ measurements by the Atmosphere Explorer-C satellite

The ion densities observed as the Atmosphere Explorer-C satellite passed through an aurora at F-region altitudes are compared to those calculated from photochemical theory using in situ measurements of atmospheric parameters (ionic and neutral composition; electron flux; neutral temperature; ion temperature) along the satellite track together with current values for reaction rates. Good agreement is obtained for the ions O2(+), NO(+), and N2(+). The atomic nitrogen densities calculated from the observed NO(+)/O2(+) ratio are found to account for about 60% of the N(+) production through electron impact on N and the resonant charge exchange of O(+)(2P) with N(4S). The N density at about 280 km, the region of the most intense electron fluxes (20 erg/sq cm/sec), is between 20 and 70 million/cu cm.

Torr, M. R.↗
NASA NTRS2018

NASA 2018 Green Propulsion Roadmap

The Green Propulsion Working Group (GPWG) is a technical guidance working group formed April 2017 under the Agency's Capability Leadership Team The GPWG was tasked with recommending an agency road map and providing guidance to NASA on green propulsion technology development and infusion The GPWG's efforts focus on ionic liquid propellants and related technologies The GPWG was chartered with three representatives from NASA Centers currently exploring green propulsion technologies As other Centers may explore programs that utilize green propulsion, membership of the working group can be expanded to include more interested parties Working group also solicits and coordinates with other government agencies (e.g. AFRL, MDA) In 2015, JANNAF hosted a Technical Interchange Meeting (TIM) on Green Monopropellant Alternatives to Hydrazine (GMAH) Included both Government and non-Government contributions on the State-of-the-Art in Green Propulsion Technology Following the TIM, a Government-only session (USAF/AFRL/NASA/MDA/DLA) reviewed and identified remaining technical gaps in Green Propulsion In 2016, an inter-agency team (AFRL/NASA/MDA) worked together to develop an informal inter-agency "roadmap" based on the outcome of the TIM Approach consisted of near-term, mid-term, and long-term technology advancement areas, approaching incrementally larger thrust classes The NASA Green Propulsion Working Group reviewed the work of the 2016 Inter-Agency Working Group, and concurs that the identified technical gaps and technology development areas are still relevant and necessary to see green propulsion technology advanced The GPWG recommends the 2016 roadmap be adopted as baseline for NASA needs, with some additions The focus of the 2016 inter-agency roadmap was primarily on the thruster technology. The Agency must also invest in understanding the broader propulsion system-level technology gaps in parallel. Timeframes are considered suggested from a priority standpoint, but are also flexible as some efforts will need to occur in the nearer term or concurrently in order to meet specific mission requirements The GPWG developed 2018 roadmap breaks down the technology development goals into Technology Development Areas (TDA's), and identifies the near-, mid, and long-term sub-goals within those areas. Those TDA's are: Thruster Hardware Development Modeling & Tools Development Materials Properties and Compatibility Propellant Development.

Cavender, Dan↗
DOE OSTI2023

Anion modification for stable solid electrolyte interphase in anode-free lithium metal batteries

The durability of anode-free Li metal batteries is largely limited by the undesired Li plating/stripping irreversibility on the current collector due to the infinite volume change, uncontrollable Li dendrite growth, and continuous parasitic reactions between Li metal and the electrolyte. To address these challenges, the formation of a stable and robust solid electrolyte interphase (SEI) with high ionic conductivity and strong mechanical strength is critical. Here, we developed an advanced electrolyte by introducing LiNO 3 into the localized high concentration electrolyte (LHCE) with lithium bis(fluorosulfonyl)imide (LiFSI) salt, 1,2-dimethoxyethane (DME) solvent, and 1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropylether (TFTE) diluent to in situ construct a LiF and Li x N y O z co-enriched passivation layer on the Cu current collector. The synergetic effect of high mechanical strength of LiF and high ionic conductivity of Li x N y O z endows the Li metal anode with a high Coulombic efficiency (CE) of 99.35%. In conclusion, in anode-free Li metal pouch cell using LiFePO 4 (LFP) as a cathode holds an exceptionally improved capacity retention under the charging/discharging rate of 1/3 C, demonstrating great promise for developing dendrite-free and safe Li metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Highly Durable Fluorinated High Oxygen Permeability Ionomers for Proton Exchange Membrane Fuel Cells

For proton exchange membrane fuel cells to be cost-competitive in light- and heavy-duty vehicle applications, their Pt content in the catalyst layers needs to be lowered. However, lowering the Pt content results in voltage losses due to high local oxygen transport resistances at the ionomer–Pt interface. It is therefore crucial to use ionomers that have higher oxygen permeability than Nafion. In this paper, novel high oxygen permeability ionomers (HOPIs) are presented, with up to five times higher oxygen permeability than Nafion, synthesized by copolymerization of perfluoro-2,2-dimethyl-1,3-dioxole (PDD) with perfluoro(4-methyl-3,6-dioxaoct-7-ene) sulfonyl fluoride (PFSVE). PDD is the source of higher permeability due to its open ring structure, while PFSVE provides ionic conductivity. Optimization of PDD content and equivalent weight enables increased fuel cell performance, mainly at high current densities, where HOPIs can achieve power densities >1.25 W cm -2 and exceed the 0.8 A cm -2 U.S. Department of Energy durability target by losing only 4.5 mV, which is over six times less than 30 mV. Finally, the interactions between HOPI and SO 3 - groups with a PtCo/C catalyst are also elucidated here at a fundamental level.

25 ENERGY STORAGE↗
DOE OSTI2020

Highly Active Rhenium-, Ruthenium-, and Iridium-Based Dichalcogenide Electrocatalysts for Oxygen Reduction and Oxygen Evolution Reactions in Aprotic Media

Transition metal dichalcogenides (TMDCs) have garnered much attention recently due to their remarkable performance for different electrochemical systems. In this study, we report on the synthesis and catalysis of less studied TMDC nanoflakes (NFs) with a design space comprised of three transition metals (rhenium, ruthenium, and iridium) and three chalcogens (sulfur, selenium, and tellurium) for the oxygen reduction and evolution reactions (ORR and OER) in an aprotic hybrid electrolyte containing 0.1 M lithium bis(trifluoromethanesulfonypimide salt in 1-ethyl-3-methylimidazolium tetrafluoroborate ionic liquid and dimethyl sulfoxide. Our results indicate that among the tested catalysts, ReS2 exhibits the highest current density for both ORR and OER, beyond those of the state-of-the-art catalysts used in aprotic media with Li salts. We performed density functional calculations to provide a mechanistic understanding of the reactions in the ReS2 NFs/ionic liquid system. These novel bifunctional catalyst results could open a way for exploiting the unique properties of these materials in Li-O-2 batteries as well as other important electrochemical systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Molecular Insight into the Effects of Clustering on the Dynamics of Ionomers in Solutions

Ionizable groups tethered to polymers enable their many current and potential applications. However, these functionalities drive the formation of physical networks through clustering of the ionic groups, resulting in constrained dynamics of the macromolecules. Understanding the molecular origin of this hindrance remains a critical fundamental question, whose solution will directly impact the processing of ionizable polymers from molecules to viable materials. Here, in this work, using quasielastic neutron scattering accompanied by molecular dynamics simulations, segmental dynamics of slightly sulfonated polystyrene is studied in solutions as the cohesion of the ionic assemblies is tuned. We find that in cyclohexane the ionic assemblies act as centers of confinement, affecting dynamics both on macroscopic lengths and in the vicinity of the ionic assemblies. Addition of a small amount of ethanol affects the packing of the ionizable groups within the assemblies, which in turn enhances the chain dynamics.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Regenerative Solid Interfaces Enhance High-Performance All- Solid-State Lithium Batteries

All-solid-state Lithium batteries (ASSLBs) have gained widespread attention in recent years. However, their performance is still largely limited by the poor transport properties and stability of the solid-solid interfaces (SSIs). In this study, we report a new strategy for creating a reversible interface with good conductivity and self-adaptive mechanical properties for high-performance all-solid-state lithium batteries (ASSLBs). The interface is formed in situ from nanosized lithium iodide (LiI), a component of the solid-state electrolyte (SSE), which flows plastically along the SSE interfaces under high pressure due to its high ductility. Moreover, LiI segregates and enriches along the Li/SSE interfaces, reversibly enhancing Li plating/stripping due to its lithophilicity and high ionic conductivity. This dynamic LiI interface enables stable operation of metallic Li anode (>1000 h) at high current densities and elevated temperatures, and long-term cycling of all-solid-state Li-sulfur batteries (>250 cycles) with high sulfur utilization rate (>1400 mAh g-1) and areal capacity (>2 mAh cm-2). This study reveals a unique role of LiI in building robust SSIs and provides new insights into the design of novel SSEs and interfaces for high-performance ASSLBs.

Yu, Zhaoxin↗
DOE OSTI2025

On Rate-Limiting Mechanisms in NMC Cathodes: The Interplay of Low and High Current Constraints

In this study, we investigate the rate performance limits in LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathodes for lithium-ion batteries, focusing on how cathode thickness, porosity, and threshold voltage impact discharge capacity. By conducting galvanostatic discharge experiments across a wide range of current densities using cathodes of varying thicknesses and porosities, we identify two distinct rate-limiting mechanisms: ionic liquid-diffusion and Ohmic/charge-transfer limitations. Our findings show that thick, dense cathodes are primarily limited by lithium diffusion in the electrolyte, while thinner and more porous cathodes are dominated by Ohmic/charge-transfer limitations, particularly at higher lower cutoff voltages. Crucially, these results allow us to identify the rate-limiting mechanisms in different cathode configurations, offering clear insights into how cathode design can be optimized for improved performance. Understanding these mechanisms is essential for designing next-generation batteries with enhanced rate performance, which is critical for applications such as electric vehicles and renewable energy storage systems.

Brischetto, Martin (ORCID:0000000339865813)↗