Search NASA⌕ Search

SEARCH · Search NASA

Results for “irradiation damage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

BOILER Experiment Material Characterization and HFIR Irradiation Status

Pre-oxidized alumina-forming austenitic (AFA) steels have been previously identified as candidate alloys for structural components in lead-cooled fast reactors (LFRs). They offer compatibility with liquid Pb, high-temperature strength, formability, and cost advantages. However, variations in Ni content can affect the formation and stability of the Al 2 O 3 layer, influencing compatibility with liquid Pb. The effect of fast neutron irradiation on Al 2 O 3 stability in liquid Pb also requires evaluation. Therefore, understanding how Ni concentrations impacts pre-oxidized AFAs under combined extremes of irradiation and liquid metal corrosion is essential before safe deployment. The Behavior Of In-situ Lead Environments & Radiation (BOILER) experiment was developed under the Nuclear Science User Facilities (NSUF) program to integrate alloy development, irradiation experiment design, and irradiated materials characterization. In this effort, two pre-oxidized AFA steels with 20 wt% and 25 wt% Ni, hereinafter referred to as GA05-20Ni and GA05-25Ni, were produced. An irradiation experiment was then planned for the High Flux Isotope Reactor (HFIR), designed for passive heating of irradiation rabbit capsules from gamma heating in the HFIR flux trap (1 × 10 15 n/cm 2 ·s, >0.1 MeV). This heating melts Pb and exposes the pre-oxidized AFA steel specimens to nominal temperatures of 400 and 650°C. Detailed neutronics and thermal analyses were performed, though based on nominal design rather than as-built, as-irradiated conditions. This report documents further characterization of the pre-oxidized AFAs in the unirradiated condition. It also includes as-built thermal analysis using measured component dimensions, updated fill gas concentrations, and actual HFIR irradiation positions. Finally, the report summarizes capsule fabrication, current irradiation status, projected completion, estimated damage accumulation, and initial plans for post-irradiation examination plans.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Size-dependent radiation damage mechanisms in nanowires and nanoporous structures

Nanostructures with a high density of interfaces, such as in nanoporous materials and nanowires, resist radiation damage by promoting the annihilation and migration of defects. This study details the size effect and origins of the radiation damage mechanisms in nanowires and nanoporous structures in model face-centered (gold) and body-centered (niobium) cubic nanostructures using accelerated multi-cascade atomistic simulations and in-situ ion irradiation experiments. Our results reveal three different size-dependent mechanisms of damage accumulation in irradiated nanowires and nanoporous structures: sputtering for very small nanowires and ligaments, the formation and accumulation of point defects and dislocation loops in larger nanowires, and a face-centered-cubic to hexagonal-close-packed phase transformation for a narrow range of wire diameters in the case of gold nanowires. Smaller nanowires and ligaments have a net effect of lowering the radiation damage as compared to larger wires that can be traced back to the fact that smaller nanowires transition from a rapid accumulation of defects to a saturation and annihilation mechanism at a lower dose than larger nanowires. These irradiation damage mechanisms are accompanied with radiation-induced surface roughening resulting from defect-surface interactions. Comparisons between nanowires and nanoporous structures show that the various mechanisms seen in nanowires provide adequate bounds for the defect accumulation mechanisms in nanoporous structures with the difference attributed to the role of nodes connecting ligaments in nanoporous structures. Altogether, our results shed light on the compounded, size-dependent mechanisms leading to the radiation resistance of nanowires and nanoporous structures.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Irradiation Driven Restructuring of Nanocrystalline ThO 2 and Th 1–x U x O 2 Thin Films

Irradiation induced structural changes of actinide oxide materials is a key consideration in their development and use as nuclear fuels. This study reported on the synthesis of ThO 2 and Th 1–x U x O 2 (x = 0.15, 0.50) thin films, fabricated using electrospray-assisted solution combustion synthesis, and their responses to ion irradiation. Krypton ion irradiations, up to a fluence of 1 × 10 16 ions/cm 2 , were carried out to simulate radiation damage induced by fission products in a reactor environment. Structural and chemical changes induced by irradiation were analyzed using high-resolution scanning transmission electron microscopy (STEM), energy-dispersive X-ray spectroscopy (EDS), and electron energy-loss spectroscopy (EELS). It was determined that the extent and nature of irradiation-induced damage are strongly correlated with the uranium content. ThO 2 films were most susceptible to radiation-induced damage, with significant cavity formation and delamination from the substrate at high fluence. Of the compositions studied, Th 0.85 U 0.15 O 2 films showed the highest stability, characterized by moderate grain growth and the absence of voids or severe defect structures. In contrast, Th 0.5 U 0.5 O 2 films accumulated extensive damage, including the formation of a nanocrystalline central region. EELS analysis indicated that oxygen displacement is the primary driver of structural degradation in Th 0.5 U 0.5 O 2 films. α-particle spectroscopy confirmed minimal actinide loss across all compositions, underscoring the mechanical robustness of the films. These findings provide insight into the irradiation-induced damage mechanisms in Th O2 and Th 1–x U x O 2 systems, supporting their development as potential materials for nuclear fuels and irradiation-tolerant thin film targets in nuclear physics measurements.

Th1−xUxO2↗
DOE OSTI2023

Effect of local chemical order on the irradiation-induced defect evolution in CrCoNi medium-entropy alloy

High- (and medium-) entropy alloys have emerged as potentially suitable structural materials for nuclear applications, particularly as they appear to show promising irradiation resistance. Recent studies have provided evidence of the presence of local chemical order (LCO) as a salient feature of these complex concentrated solid-solution alloys. However, the influence of such LCO on their irradiation response has remained uncertain thus far. Here, in this work, we combine ion irradiation experiments with large-scale atomistic simulations to reveal that the presence of chemical short-range order, developed as an early stage of LCO, slows down the formation and evolution of point defects in the equiatomic medium-entropy alloy CrCoNi during irradiation. In particular, the irradiation-induced vacancies and interstitials exhibit a smaller difference in their mobility, arising from a stronger effect of LCO in localizing interstitial diffusion. This effect promotes their recombination as the LCO serves to tune the migration energy barriers of these point defects, thereby delaying the initiation of damage. These findings imply that local chemical ordering may provide a variable in the design space to enhance the resistance of multi-principal element alloys to irradiation damage.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Large-Scale Image Analysis for Investigating Spatio-Temporal Changes in Nuclear DNA Damage Caused by Nitrogen Atmospheric Pressure Plasma Jets

The effective clinical application of atmospheric pressure plasma jet (APPJ) treatments requires a well-founded methodology that can describe the interactions between the plasma jet and a treated sample and the temporal and spatial changes that result from the treatment. In this study, we developed a large-scale image analysis method to identify the cell-cycle stage and quantify damage to nuclear DNA in single cells. The method was then tested and used to examine spatio-temporal distributions of nuclear DNA damage in two cell lines from the same anatomic location, namely the oral cavity, after treatment with a nitrogen APPJ. One cell line was malignant, and the other, nonmalignant. The results showed that DNA damage in cancer cells was maximized at the plasma jet treatment region, where the APPJ directly contacted the sample, and declined radially outward. As incubation continued, DNA damage in cancer cells decreased slightly over the first 4 h before rapidly decreasing by approximately 60% at 8 h post-treatment. In nonmalignant cells, no damage was observed within 1 h after treatment, but damage was detected 2 h after treatment. Notably, the damage was 5-fold less than that detected in irradiated cancer cells. Moreover, examining damage with respect to the cell cycle showed that S phase cells were more susceptible to DNA damage than either G1 or G2 phase cells. The proposed methodology for large-scale image analysis is not limited to APPJ post-treatment applications and can be utilized to evaluate biological samples affected by any type of radiation, and, more so, the cell-cycle classification can be used on any cell type with any nuclear DNA staining.

cellular imaging↗
DOE OSTI2022

Calculating Radiation Damage (DPA) from Transmutation Products

This is a poster for an INL poster session. Accurate models for radiation damage are crucial for predicting material performance in radiation environments. The uncertainty of state-of-the-art radiation damage models is large, contributing to excessive safety margins. A major source of this uncertainty is neglecting the effect that transmutation products have on radiation damage. Transmutation products are new nuclides formed by neutron activation during irradiation; they can contribute to radiation damage by additional neutron capture or decay events. Ignoring the contribution of transmutation products leads to a significant underprediction of the radiation damage (e.g., >10% error in 316 stainless steel). This underprediction is accounted for in part by adding larger safety margins to designs. Currently, the state of the art explicitly accounts for only a single transmutation product, namely nickel-59, during the radiation damage calculation. All other transmutation products are assumed to not contribute to the radiation damage, because there is currently no established method to systematically track all or a selection of radiation damage contributions of transmutation products during activation. In the case of nickel-59, the current method is to apply a precalculated correlation that cannot be used for any other nuclide and is largely dependent on all nuclear engineers being experts in this niche topic. This project proposed to methodically find other transmutation products that cause significant radiation damage, and then to develop a general framework for systematically tracking the radiation damage from these nuclides. This was accomplished by combining the radiation damage calculation into the transmutation calculation already performed for irradiated structural materials. The key idea of our framework is to introduce radiation-damage "pseudo-nuclides" to the list of nuclides used in the transmutation analysis. This allows radiation damage to be tracked alongside the creation and destruction of transmutation products. The main deliverable of this project is a general framework for computing radiation damage while the damaged material undergoes transmutation; this capability allows a significantly more accurate estimation of radiation damage, and in turn reduce required safety margins thereby reducing the cost to construct reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Microstructural changes of proton irradiated Hastelloy-N and in situ micropillar compression testing of one single grain at different local damage levels

Here, in situ micropillar compression was used to study the deformation of proton-irradiated Hastelloy-N at different damage levels. Multiple pillars were prepared from a single domain along the cross-section of 2.5 MeV proton-irradiated Hastelloy-N. Depending on the location of micropillars, the critical resolved shear stress was obtained as a function of local damage levels. Such an approach eliminates the variation of yield stress due to the difference in the Schmid factor. Microstructural characterization showed that irradiation hardening is contributed by complicated defect structures, including (a) dislocation loops with many in corduroy-like alignments, (2) dislocations pile up, and (3) Cottrell atmosphere. Silicon atoms are found to segregate at dislocation lines and loops and form complicated Cottrell cloud patterns. The critical resolved shear stress, $t_{crss}$, and hardening exponents were both extracted as a function of displacements per atom values up to 2.3. There was a 60% increase in $t_{crss}$ at the highest damage level.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Nuclear reactor radiation and temperature effects on piezoelectric surface acoustic wave devices

Surface acoustic wave (SAW) resonators were characterized in-situ in a nuclear reactor environment at high temperature. Devices based on lithium niobate (LiNbO 3 ), aluminum nitride (sc-AlN), and thin-film aluminum nitride on sapphire substrate (AlN/sapphire) were tested up to 400 °C temperature and 1.9 × 10 12 n/cm 2 s neutron flux. Shifts in device resonant frequency were detected in response to temperature and neutron flux. Devices undergo a frequency change when exposed to neutron flux. At 300 °C, AlN/sapphire produced the strongest neutron flux response about 1.02 ppm at 1.27 × 10 12 n/cm 2 s neutron flux (5.7 × 10 4 rad-Si/hr neutron dose rate), compared to 0.30 ppm for LiNbO 3 and 0.17 ppm for sc-AlN. While the transient kinetics in response to step change in neutron flux support the defect-accumulation mechanism, the concurrent measurement of device temperature using resistive temperature sensor suggests additional heating caused by absorption of gamma rays can also play a role. These results make SAW devices attractive candidates for sensor applications in extreme environments.

Aluminum nitride↗
DOE OSTI2021

Deuterium retention in MeV ion-irradiated beryllium

Beryllium, as the material of choice for the ITER first wall, will be subject to high energy neutrons during the operation of the fusion device. Such irradiation will create displacement damage in the crystal lattice, which is known to influence hydrogen isotope retention, e.g. in iron and tungsten. Here in our study, we irradiated beryllium samples with high-energy oxygen ions up to various dpa levels (0.01 dpa, 0.1 dpa, and 1 dpa) and subsequently exposed the samples to deuterium plasma at 370 K and 573 K. The amount of retained deuterium was measured by thermal desorption spectroscopy and nuclear reaction analysis and was found to decrease by about 18% in the samples damaged up to 0.1 dpa compared to the undamaged ones. Further damaging up to 1 dpa did not show any additional effects on deuterium retention. Transmission electron microscopy was used to check for the existence of bubbles after plasma exposure.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Unveiling Swift Heavy Ion Track Morphology in Sr-Based High-Entropy Perovskites

The incorporation of multiple cations on a single lattice site in the high-entropy oxides is considered the key driving factor for modifying the known atomic-level response to energetic ion irradiation due to the presence of structural disorder; however, these effects are not well-understood yet. In this work, we present atomic-level insight into irradiation-induced nanoscale phase transformations in a perovskite-structured high-entropy oxide, Sr(Zr 0.2 Sn 0.2 Ti 0.2 Hf 0.2 Nb 0.2 )O 3 (Sr(HE)O 3 ), subjected to 774 MeV swift Xe heavy ions, where damage is dominated by inelastic ion−lattice interactions. While these ions generally are known to create nanoscale disordered channels, “ion tracks”, along the penetration direction in the material, this study shows the formation of discontinuous and partially recrystallized ion tracks in Sr(HE)O 3 . Compared to SrTiO 3 irradiated under identical energy loss conditions, the ion tracks in Sr(HE)O 3 exhibit significantly reduced diameters and a markedly different interfacial structure. Notably, the crystalline−amorphous interface in Sr(HE)O 3 shows minimal lattice distortion, confined to approximately 2−3 monolayers, in contrast to the extended disordered shell commonly observed in SrTiO 3 . Using in situ atomic-resolution electron microscopy, we further demonstrate that the amorphous/disordered regions within Sr(HE)O 3 ion tracks remain highly stable under electron irradiation, whereas tracks in SrTiO 3 readily recrystallize. This enhanced stability is attributed to the dominance of structural and chemical complexity arising from multiple B-site cations, which suppress defect migration and templated recrystallization driven by electronic excitations and local heating. Overall, this study highlights how high-entropy oxide chemistry fundamentally reshapes irradiation damage evolution, offering insights into defect formation and phase stability under extreme conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural Characterizations of Two High Fluence Baffle-Former Bolts Retrieved from a Westinghouse Two-loop Downflow Type PWR

As one of the pressurized water reactor (PWR) internal components, baffle-former bolts (BFBs) are subjected to significant mechanical stress and neutron irradiation from the reactor core during the plant operation. Over the long operation period, these conditions lead to potential degradation and reduced load-carrying capacity of the bolts. In support of evaluating long-term operational performance of materials used in core internal components, the Oak Ridge National Laboratory (ORNL), through the Department of Energy (DOE), Office of Nuclear Energy, Light Water Reactor Sustainability (LWRS) Program, Materials Research Pathway (MRP), has harvested two high fluence BFBs from a commercial Westinghouse two-loop downflow type PWR. The two bolts of interest, i.e. bolts # 4412 and 4416, were withdrawn from service in 2011 as part of a preventative replacement plan. No identification of cracking or potential damage was found for these bolts during their removal in 2011. However, the bolts required a lower torque for removal from the baffle structure than the original torque specified during installation. Irradiation damage levels in the bolts range from 15 to 41 displacements per atom. The goal of this project is to perform detailed microstructural and mechanical property characterization of BFBs following in-service exposures. The information from these bolts will be integral to the LWRS program initiatives in evaluating end of life microstructure and properties. Furthermore, valuable data will be obtained that can be incorporated into model predictions of long term irradiation behavior and compared to results obtained from experimental reactor conditions

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Vacancy-driven variations in the phonon density of states of fast neutron irradiated nuclear graphite

Research examining radiation damage and its effects in graphite began in the 1940’s during the development of moderated nuclear reactors. Interest in this topic is expanding because of emerging applications associated with fullerenes and carbon nanostructures as well as its long-standing use as a fission moderator. In this work, we report the measurements of the full phonon density of states of irradiated nuclear graphite using inelastic neutron scattering experiments at room temperature. The samples were previously exposed to different levels of neutron doses and irradiation temperatures. The phonon density of states of perfect and defected graphite supercells including different configurations of vacancies and interstitials were calculated using first-principles direct method. Despite high neutron irradiation doses, the scattering measurements show that the induced damage is localized, and the layered structure is preserved. In conclusion, a comparison of the measured phonon densities of states of irradiated samples with those calculated of defected supercells indicates that the main changes observed are mainly attributed to formation of vacancies.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of radiation damage on the yielding and fracture of nanowires

Irradiated nanowires' strength can change with their diameter. Though damaged by radiation, defects get cleaned during loading, returning the nanowires to their pristine state. This suggests that radiation has little impact on their fracture behavior.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Caffeic acid attenuates irradiation-induced hematopoietic stem cell apoptosis through inhibiting mitochondrial damage

Highlights: • IR-induced mitochondrial damage accelerates HSC apoptosis. • CA attenuates mitochondrial damage and apoptosis of HSCs induced by IR. • CA protects against BM hematopoietic failure in mice after IR exposure. Hematopoietic stem cells (HSCs) are sensitive to ionizing radiation (IR) damage, and its injury is the primary cause of bone marrow (BM) hematopoietic failure and even death after exposure to a certain dose of IR. However, the underlying mechanisms remain incompletely understood. Here we show that mitochondrial oxidative damage, which is characterized by mitochondrial reactive oxygen species overproduction, mitochondrial membrane potential reduction and mitochondrial permeability transition pore opening, is rapidly induced in both human and mouse HSCs and directly accelerates HSC apoptosis after IR exposure. Mechanistically, 5-lipoxygenase (5-LOX) is induced by IR exposure and contributes to IR-induced mitochondrial oxidative damage through inducing lipid peroxidation. Intriguingly, a natural antioxidant, caffeic acid (CA), can attenuate IR-induced HSC apoptosis through suppressing 5-LOX-mediated mitochondrial oxidative damage, thus protecting against BM hematopoietic failure after IR exposure. These findings uncover a critical role for mitochondria in IR-induced HSC injury and highlight the therapeutic potential of CA in BM hematopoietic failure induced by IR.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Atomistic Modeling of Irradiation-Induced Defects and Clusters in Additively-Manufactured Austenitic Stainless Steel

Understanding the progression of irradiation-induced defects in real materials and alloys requires insight into the interaction between point defects, defect clusters, and the existing microstructure. This is particularly true when it comes to additively manufactured (AM) materials with complicated microstructures and residual stresses. In this work, we employ molecular dynamics (MD) to simulate the creation of point defects via primary radiation damage modeling and point defect interactions with extended defects such as voids and dislocations using simplified but representative alloy compositions. We analyze the effect of alloying elements on the formation energies of the defect clusters and measure interactions such as sink strengths and binding energies. This study provides insight into the unique behaviors of irradiation damage in AM materials and information necessary to bridge the gap in length and time scales to connect the atomistic behavior of defects to longer length scale simulations such as cluster dynamics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Recent progress on understanding the temperature-dependent irradiation resistance ranking among NiFe, NiCoCr, and NiCoFeCr alloys: A review

Systematic temperature-effects investigations on damage evolution in ion-irradiated Ni-based concentrated solid-solution alloys (CSAs) are pivotal to provide reliance on their use in nuclear applications. Here, in search of the origin behind the temperature-dependent irradiation resistance ranking among equiatomic NiFe, NiCoCr and NiCoFeCr alloys, we have compared, previously experimental and theoretical published data involving ion irradiation experiments performed on these alloys with new ion channeling results from ion-irradiated NiCoFeCr at 500 K. Moreover, the current results are compared with independent theoretical calculations and relevant TEM results from literature, which allow us to suggest that the lower migration energy of vacancies in NiCoCr, as compared with those in NiFe and NiCoFeCr, is the reason behind why NiCoCr is no longer outperforming NiFe under ion irradiation above 300 K.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Radiation Damage Mitigation in FeCrAl Alloy at Sub-Recrystallization Temperatures

Traditional defect recovery methods rely on high-temperature annealing, often exceeding 750 °C for FeCrAl. In this study, we introduce electron wind force (EWF)-assisted annealing as an alternative approach to mitigate irradiation-induced defects at significantly lower temperatures. FeCrAl samples irradiated with 5 MeV Zr 2+ ions at a dose of 10 14 cm −2 were annealed using EWF at 250 °C for 60 s. We demonstrate a remarkable transformation in the irradiated microstructure, where significant increases in kernel average misorientation (KAM) and low-angle grain boundaries (LAGBs) typically indicate heightened defect density; the use of EWF annealing reversed these effects. X-ray diffraction (XRD) confirmed these findings, showing substantial reductions in full width at half maximum (FWHM) values and a realignment of peak positions toward their original states, indicative of stress and defect recovery. To compare the effectiveness of EWF, we also conducted traditional thermal annealing at 250 °C for 7 h, which proved less effective in defect recovery as evidenced by less pronounced improvements in XRD FWHM values.

FeCrAl alloys↗