Search NASA⌕ Search

SEARCH · Search NASA

Results for “laser sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Optical measurements of soot in premixed flames

Two laser diagnostic techniques were used to measure soot volume fractions, number densities and soot particle radii in premixed propane/oxygen flat flames. The two techniques were two wavelength extinction, using 514.5 to 632.8 nm and 457.9 to 632.8 nm wavelength combinations, and extinction/scattering using 514.5 nm light. The flames were fuel rich and had cold gas velocities varying from 3.4 to 5.5 cm/s. Measurements were made at various heights above the sintered bronze, water colored flat flame burner with the equivalence ratio and cold gas velocity fixed. Also, measurements were made at a fixed height above the burner and fixed cold gas velocity while varying the equivalence ratio. Both laser techniques are based on the same underlying assumptions of particle size distribution and soot optical properties. Full Mie theory was used to determine the extinction coefficients and the scattering efficiencies. Temperature measurements in the flame were made using infrared radiometry and fine wire thermocouples. Good agreement between the two techniques in terms of soot particle radii, number density and volume fraction was found for intensity ratios between 0.1 and 0.8.

Lyons, Valerie J.↗
NASA NTRS1987

Application of scanning acoustic microscopy to advanced structural ceramics

A review is presentod of research investigations of several acoustic microscopy techniques for application to structural ceramics for advanced heat engines. Results obtained with scanning acoustic microscopy (SAM), scanning laser acoustic microscopy (SLAM), scanning electron acoustic microscopy (SEAM), and photoacoustic microscopy (PAM) are compared. The techniques were evaluated on research samples of green and sintered monolithic silicon nitrides and silicon carbides in the form of modulus-of-rupture bars containing deliberately introduced flaws. Strengths and limitations of the techniques are described with emphasis on statistics of detectability of flaws that constitute potential fracture origins.

Vary, Alex↗
NASA NTRS2019

Optimization of Aluminum-Tin Ink Composition and Sintering in Atmospheric Conditions

This study will focus on the basics of generating an aluminum-tin ink that can sinter in air and exhibits properties near that of a solid aluminum-tin alloy. Sintering temperatures will also be assessed in this study. Once the optimal aluminum ink composition is determined, the optimal ink thickness for homogeneous sintering must be determined by additional experimentation. Additive manufacturing is a rapidly developing and growing manufacturing process and has proven successful in many different ways. Processes, such as extrusion three-dimensional (3D) printing and selective laser melting (SLM), have proven to work but have limitations, such as material capabilities or density issues. SLM is a revolutionary process for additive manufacturing of metals but cannot be used in outer space due to the need for metallic powder which would diffuse into the atmosphere in a zero-gravity environment. For this reason, metallic ink additive manufacturing is a potential solution. Work is being done on metallic ink additive manufacturing in a vacuum for electrical applications. This project has focused on developing an aluminum-tin metallic ink that can sinter without the need of a vacuum or inert gas-purged atmosphere in order to prevent oxidation of the aluminum by adding flux. Once a potential ink composition has been determined through sintering of small disks and thin layers of ink, the ink may be studied with a multimaterial 3D printer at NASA Marshall Space Flight Center (MSFC) in future experiments. If successful, this aluminum-tin ink will be capable for use on the International Space Station to make replacement parts quickly. Along with its zero-gravity advantages, this ink may also have applications on Earth because it may be extruded on a substrate with precise ceramic tips in a 3D printing process. This would allow the fabrication of precise, complex shapes and may generate a much faster and more efficient printing process as compared with traditional powder bed additive manufacturing processes. The process would not be limited by a small building volume because the system would not require an enclosed chamber.

Courtright, Z. S.↗
DOE OSTI2020

U 3 Si 2 and UO 2 composites densified by spark plasma sintering for accident-tolerant fuels

This work reports the synthesis and characterization of the U 3 Si 2 and UO 2 composites sintered by spark plasma sintering (SPS) with controlled microstructures for accident-tolerant fuel application. The U 3 Si 2 and UO 2 composites with different silicide and oxide ratios were synthesized by SPS at temperatures from 1000 to 1300 °C for 5 minutes. The microstructure and phase composition of the SPS densified composite fuels were characterized with scanning electron microscopy, X-ray diffraction (XRD), and energy dispersed spectroscopy (EDS). A systematic study of the thermal and mechanical properties was conducted using microhardness testing and laser flash apparatus, along with oxidation resistance measurements using thermogravimetric analysis (TGA). The results show that the synthesis of composite fuels can be achieved with a 90% theoretical density (TD) at 1000 °C and over 95% TD when sintered at 1300 °C. XRD and EDS results confirmed that the dominant phases in the composites are U 3 Si 2 and UO 2 . Improved physical density generally leads to improved hardness, fracture toughness, thermal diffusivity, and onset temperature during the oxidation process. U 3 Si 2 was found to play a dominant role in determining the mechanical and oxidation properties of the composite fuels, whereas UO 2 had a more important impact on controlling the thermal diffusivity of the composites. The composite with 50 wt% UO 2 sintered at 1300 °C displayed the onset oxidation temperature of 500 °C by dynamic oxidation testing using TGA at a ramp degree of 10 °C/min. The composite also achieved a high fracture toughness of ~3.5 MPa m ½ . Finally, these results highlight the potential of composite fuel forms densified by SPS with simultaneously enhanced fissile element density, fracture toughness, thermal transport properties, and oxidation resistance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1998

Thermal High- and Low-Cycle Fatigue Behavior of Thick Thermal Barrier Coating Systems

Ceramic thermal barrier coatings have received increasing attention for advanced gas turbine and diesel engine applications because of their ability to provide thermal insulation to engine components. However, the durability of these coatings under the severe thermal cycling conditions encountered in a diesel engine (ref. 1) still remains a major issue. In this research at the NASA Lewis Research Center, a high-power laser was used to investigate the thermal fatigue behavior of a yttria-stabilized zirconia coating system under simulated diesel engine conditions. The mechanisms of fatigue crack initiation and propagation, and of coating failure under complex thermal low-cycle fatigue (LCF, representing stop/start cycles) and thermal high-cycle fatigue (HCF, representing operation at 1300 rpm) are described. Continuous wave and pulse laser modes were used to simulate pure LCF and combined LCF/HCF, respectively (ref. 2). The LCF mechanism was found to be closely related to the coating sintering and creep at high temperatures. These creep strains in the ceramic coating led to a tensile stress state during cooling, thus providing the major driving force for crack growth under LCF conditions. The combined LCF/HCF tests induced more severe coating surface cracking, microspallation, and accelerated crack growth than did the pure LCF test. HCF thermal loads also facilitated lateral crack branching and ceramic/bond coat interface delaminations. HCF is associated with the cyclic stresses originating from the high-frequency temperature fluctuation at the ceramic coating surface. The HCF thermal loads act on the crack by a wedging mechanism (ref. 1), resulting in continuous crack growth at temperature. The HCF stress intensity factor amplitude increases with the interaction depth and temperature swing, and decreases with the crack depth. HCF damage also increases with the thermal expansion coefficient and the Young's modulus of the ceramic coating (refs. 1 and 3).

Miller, Robert A.↗
DOE OSTI2020

3D printed transparent ceramic YAG laser rods: Matching the core-clad refractive index

Yttrium Aluminum Garnet (YAG) solid state laser gain media rods with an active Neodymium-doped core and an optically-clear cladding region were additively manufactured via direct-ink-writing (DIW), followed by sintering and hot isostatic pressing to form fully dense optical ceramics. Lutetium and Gadolinium were chosen as optically-inert co-doping ions in the clad to match the increase in refractive index caused by the Neodymium in the core. Additionally, either 11.6% Lutetium or 3.8% Gadolinium can be used to match the index change from 2% neodymium; however, differences in diffusion distances across the core-clad interface lead to large fluctuations in index in that region. These index fluctuations can be minimized either by matching dopants with similar diffusion distances, or by implementing a gradual gradient in the doping profile, possible through DIW, rather than a sharp compositional interface attainable via more standard fabrication methods. This improvement in index homogeneity resulted in a 40% improvement in lasing performance compared with that of a core-clad rod fabricated with a sharp interface between the doped and undoped regions.

36 MATERIALS SCIENCE↗
NASA NTRS1988

Optical measurements of soot and temperature profiles in premixed propane-oxygen flames

Two laser diagnostic techniques were used to measure soot volume fractions, number densities and soot particle radii in premixed propane/oxygen flat flames. The two techniques used were two wavelength extinction, using 514.5 nm to 632.8 nm and 457.9 nm to 632.8 nm wavelength combinations, and extinction/scattering using 514.5 nm light. The flames wre fuel-rich (equivalence ratios from 2.1 to 2.8) and had cold gas velocities varying from 3.4 to 5.5 cm/s. Measurements were made at various heights above the sintered-bronze, water-cooled flat flame burner with the equivalence ratio and cold gas velocity fixed. Also, measurements were made at a fixed height above the burner and fixed cold gas velocity while varying the equivalence ratio. Both laser techniques are based on the same underlying assumptions of particle size distribution and soot optical properties. Full Mie theory was used to determine the extinction coefficients K sub ext, and the scattering efficiencies, Q sub vv. Temperature measurements in the flames were made using infrared radiometry. Good agreement between the two techniques in terms of soot particle radii, number density and volume fraction was found for intensity ratios (I/I sub o) between 0.1 and 0.8. For intensity ratios higher or lower than this range, the differences in extinction coefficients at the wavelengths chosen for the two-wavelength method are too small to give accurate results for comparing particle radii and number densities. However, when comparing only soot volume fractions, the agreement between the two techniques continued to be good for intensity ratios up to 0.95.

Lyons, Valerie J.↗
NASA NTRS1988

Optical measurements of soot and temperature profiles in premixed propane-oxygen flames

Two laser diagnostic techniques were used to measure soot volume fractions, number densities and soot particle radii in premixed propane/oxygen flat flames. The two techniques used were two wavelength extinction, using 514.5 nm to 632.8 nm and 457.9 nm to 632.8 nm wavelength combinations, and extinction/scattering using 514.5 nm light. The flames were fuel-rich (equivalence ratios from 2.1 to 2.8) and had cold gas velocities varying from 3.4 to 5.5 cm/s. Measurements were made at various heights above the sintered-bronze, water-cooled flat flame burner with the equivalence ratio and cold gas velocity fixed. Also, measurements were made at a fixed height above the burner and fixed cold gas velocity while varying the equivalence ratio. Both laser techniques are based on the same underlying assumptions of particle size distribution and soot optical properties. Full Mie theory was used to determine the extinction coefficients K sub ext, and the scattering efficiencies, Q sub vv. Temperature measurements in the flames were made using infrared radiometry. Good agreement between the two techniques in terms of soot particle radii, number density and volume fraction was found for intensity ratios (I/I sub o) between 0.1 and 0.8. For intensity ratios higher or lower than this range, the differences in extinction coefficients at the wavelengths chosen for the two-wavelength method are too small to give accurate results for comparing particle radii and number densities. However, when comparing only soot volume fractions, the agreement between the two techniques continued to be good for intensity ratios up to 0.95.

Lyons, V. J.↗
DOE OSTI2020

Binderjet Additive Manufacturing for Complex Heat Exchanger Geometries

Concentrated Solar Power (CSP) systems play a role in the worlds development of renewable energy. Mirrors are used to concentrate sunlight that is converted into electricity or other forms of useful energy. CSP impact depends significantly on its overall economics. The U.S. Department of Energy’s (DOE’s) Solar Energy Technology Office (SETO) cost goals for 2030include $0.05/kWh levelized cost of electricity (LCOE) for a baseload plant [1]. The power cycle cost goal is $900/kWe [1]. The envisioned recompression supercritical carbondioxide (sCO2) power cycle includes four heat exchangers, which together are at least ¾ of the total power cycle cost. Meeting the cost target requires reducing the heat exchanger cost. The 260 bar and 588 °C heat exchanger requirements are challenging. Shell and tube heat exchangers can meet the requirements, but the size and cost are prohibitive. State-of-the-art diffusion bonded printed circuit heat exchanger designs are 3 m3 or larger and expensive to manufacture. Additive manufacturing enables novel heat exchanger geometries that can reduce heat exchanger size and mass [2]. Binderjet technology is an additive manufacturing modality. It selectively deposits binder material onto the powder bed to form a solid part one layer at a time. Once applied, the binder is cured, the remaining powder removed, and the part heat treated in steps to remove the binder, sinter the metal powder, and densify the part. The Binderjet printing process is more than 10x faster than the best-known metal additive modality, direct metal laser melting (DMLM), thus enabling 10x the part through-put rate [3]. The high throughput rate results in a low-cost manufacturing process capable of creating complex heat exchanger geometries. This paper introduces a complex heat exchanger geometry and methods of Binderjet processing to fabricate the geometry.

Barua, Ananda↗
DOE OSTI2020

Dissolution of Additively Manufactured Mo Disks and Structures for Accelerator Based Production of Mo-99

The press-and-sinter approach for production of Mo targets has been successfully tested and demonstrated. The main advantage of this process is that it uses readily available technology and tools that have been tuned for production of various metal and metal oxide targets. However, certain target design specifications, such as dimensional accuracy of the diameter and thickness of the disks, are required for proper fit into a target holder and therefore place strict tolerances on sintered Mo disks intended for accelerator production. Furthermore, having a target composed of multiple disks poses certain challenges for post-irradiation processing, where there is a potential for spillage of individual disks during the manipulation for dissolution inside a processing hot cell. Additive manufacturing (AM), also referred to as 3D printing, provides capabilities to design and build a single-piece Mo target that provides the opportunity for better geometry for optimized production of Mo-99, improved cooling capability, and safer post-irradiation handling. A drawback of AM Mo structures is roughness of finished surfaces, which could reduce the effectiveness of gas cooling systems. Process development for AM Mo structures using selective laser melting is described in work by Gibson and Lowden. For post-irradiation processing, it is important to look at the dissolution behavior of AM Mo structures in comparison to readily dissolved press-and-sinter Mo targets. The dissolution behavior of press-and-sinter targets has been well documented in our previous reports. In this report, we discuss results of dissolution experiments conducted with AM Mo disks and structures (provided by Oak Ridge National Laboratory [ORNL]) in 50% hydrogen peroxide (H 2 O 2 ).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure evolution of gadolinium doped cerium oxide under large thermal gradients

In this report the effects of large thermal gradient annealing on the microstructure of 10 mol% gadolinium doped ceria (GDC) were investigated. GDC powder was prepared by solvent deficient method and sintered at 1650 °C for 10 h to achieve dense ceramics with ~8 μm grain size. The densified GDC samples were subsequently annealed using a 60 W infrared laser at over 2100 °C for 1 h under a thermal gradient equivalent to ~0.3–0.5 °C/μm. The post-annealed samples at 2150 °C for 1 h exhibit grains with average length and width of 37 and 28 μm, respectively. Electron backscattered diffraction (EBSD) analysis revealed that the post-annealed sample at 2150 °C consists of grains oriented close to five principal directions (<4 3 10>, <0 0 1> and <13 1 14> on [0 0 1], and <7 6 20> and <7 2 7> on [0 1 0]) within a tolerance angle of ±10°, whereas the grains of the pre-annealed sample are randomly oriented. Gadolinium diffuses 20–30 μm away from the irradiated surface, with the measured composition of regions deeper than 30 μm, Ce 0.86 Gd 0.14 O 1.93 , is close to that of the pre-annealed sample, Ce 0.87 Gd 0.13 O 1.94 . Enhancement of total conductivity of the post-annealed GDC (1.1 × 10 -3 S cm -1 at 500 °C, and 2.1 × 10 -2 S cm -1 at 700 °C) is observed when compared to the pre-annealed GDC (3.1 × 10 -5 S cm -1 at 500 °C, and 1.7 × 10 -3 S cm -1 at 700 °C), and points to the decrease in the grain boundary (GB) resistivity. This could be attributed to both the change in GB area and grain alignment.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Development of Advanced Thermal and Environmental Barrier Coatings Using a High-Heat-Flux Testing Approach

The development of low conductivity, robust thermal and environmental barrier coatings requires advanced testing techniques that can accurately and effectively evaluate coating thermal conductivity and cyclic resistance at very high surface temperatures (up to 1700 C) under large thermal gradients. In this study, a laser high-heat-flux test approach is established for evaluating advanced low conductivity, high temperature capability thermal and environmental barrier coatings under the NASA Ultra Efficient Engine Technology (UEET) program. The test approach emphasizes the real-time monitoring and assessment of the coating thermal conductivity, which initially rises under the steady-state high temperature thermal gradient test due to coating sintering, and later drops under the cyclic thermal gradient test due to coating cracking/delamination. The coating system is then evaluated based on damage accumulation and failure after the combined steady-state and cyclic thermal gradient tests. The lattice and radiation thermal conductivity of advanced ceramic coatings can also be evaluated using laser heat-flux techniques. The external radiation resistance of the coating is assessed based on the measured specimen temperature response under a laser- heated intense radiation-flux source. The coating internal radiation contribution is investigated based on the measured apparent coating conductivity increases with the coating surface test temperature under large thermal gradient test conditions. Since an increased radiation contribution is observed at these very high surface test temperatures, by varying the laser heat-flux and coating average test temperature, the complex relation between the lattice and radiation conductivity as a function of surface and interface test temperature may be derived.

Zhu, Dongming↗
DOE OSTI2025

Orientation microscopy–assisted grain boundary analysis for protonic ceramic cell electrolytes

Abstract Grain boundaries in protonic ceramic cell (PCC) electrolytes hinder proton transport, reducing interfacial conductivity. In multicomponent PCC electrolytes, the inclusion of sintering aids further accentuates the complexity of grain boundaries. In this study, we synthesize nanocrystalline BaCe 0.4 Zr 0.4 Y 0.1 Yb 0.1 O 3− δ thin films via pulsed laser deposition and analyze their grain boundary character distributions using orientation data collected by precession electron diffraction technique. The results reveal an anisotropic distribution of grain boundary characters, with notably high populations of 180°‐tilt and twist grain boundaries. These findings provide critical insights into identifying the predominant grain boundaries in this PCC electrolyte material, assessing the vast five‐dimensional grain boundary space.

Patel, Sooraj [School of Aerospace and Mechanical ↗
NASA NTRS1987

Nondestructive evaluation of structural ceramics

A review is presented on research and development of techniques for nondestructive evaluation and characterization of advanced ceramics for heat engine applications. Highlighted in this review are Lewis Research Center efforts in microfocus radiography, scanning laser acoustic microscopy (SLAM), scanning acoustic microscopy (SAM), scanning electron acoustic microscopy (SEAM), and photoacoustic microscopy (PAM). The techniques were evaluated by applying them to research samples of green and sintered silicon nitride and silicon carbide in the form of modulus-of-rupture bars containing seeded voids. Probabilities of detection of voids were determined for diameters as small as 20 microns for microfucus radiography, SLAM, and SAM. Strengths and limitations of the techniques for ceramic applications are identified. Application of ultrasonics for characterizing ceramic microstructures is also discussed.

Klima, Stanley J.↗
NASA NTRS1990

Development of Low Conductivity and Ultra High Temperature Ceramic Coatings Using A High-Heat-Flux Testing Approach

The development of low conductivity, robust thermal and environmental barrier coatings requires advanced testing techniques that can accurately and effectively evaluate coating thermal conductivity and cyclic resistance at very high surface temperatures (up to 17OOOC) under large thermal gradients. In this study, a laser high-heat-flux test approach is established for evaluating advanced low conductivity, ultra-high temperature ceramic thermal and environmental barrier coatings under the NASA Ultra Efficient Engine Technology (UEET) program. The test approach emphasizes the real-time monitoring and assessment of the coating thermal conductivity: the initial conductivity rise under a steady-state high temperature thermal gradient test due to coating sintering, and the later coating conductivity reduction under a subsequent cyclic thermal gradient test due to coating cracking/delamination. The coating system is then evaluated based on the damage accumulations and failure after the combined steady-state and cyclic thermal gradient tests. The lattice and radiation thermal conductivity of advanced ceramic coatings can also be evaluated using laser heat-flux techniques. The coating external radiation resistance is assessed based on the measured specimen temperature response under a laser heated intense radiation flux source. The coating internal radiation contribution is investigated based on the measured apparent coating conductivity increases with the coating surface test temperature under large thermal gradient test conditions. Since an increased radiation contribution is observed at these very high surface test temperatures, by varying the laser heat-flux and coating average test temperature, the complex relation between the lattice and radiation conductivity as a function of surface and interface test temperature is derived.

Zhu, Dongming↗
DOE OSTI2025

NSUF RTE completion report for 23-4780: Microstructural Defect Induced Thermal Conductivity Reduction in Uranium Nitride and Thorium Nitride

Uranium nitride (UN) is known to have a higher thermal conductivity than traditional oxide fuels, which could lead to a more efficient energy transport and lower local temperature during its lifetime. But the thermal transport performance of UN in extreme environments has not been systematic studied. This study investigated the irradiation induced microstructural defects in UN and the impacts on thermal conductivity. The samples were produced by spark plasma sintering at University of Texas-San Antonio (UTSA), Los Alamos National Laboratory (LANL), and Idaho National Laboratory (INL). Thermal conductivity of UN before and after 2MeV proton irradiation were measured by using laser metrology at INL in a temperature range of 77-295K. Thermal conductivity measurements in this wide, cryogenic temperature range is critical to understand the phonon scattering mechanisms between the thermal energy carrier, phonons, and different types of irradiation-induced defects. In order to ensure the measurements were conducted in the same grains and minimize the impact of the local heterogeneities, the measurement locations were highlighted by fiducial marks using the focused ion beam (FIB) with grain orientation identified using the electron backscatter diffraction (EBSD) at the Center of Advanced Energy Studies (CAES). Irradiation experiment was conducted at the Ion Beam Laboratory at Texas A&M University (TAMU). A total of 6 samples were irradiated with different irradiation doses and temperatures. After irradiation, the microstructure was characterized by using Transmission Electron Microscope (TEM) at CAES (also in the FIB marks).

36 - MATERIALS SCIENCE↗
NASA NTRS1987

Uranium nitride fuel fabrication for SP-100 reactors

Fuel pins of uranium mononitride clad in Nb-1 percent Zr were fabricated for irradiation tests in EBR-II. Laboratory scale process parameters to synthesize UN powders and fabricate UN pellets were developed. Uranium mononitride was prepared by converting UO2 to UN. Fuel pellets were prepared by communition of UN briquettes, uniaxial pressing, and high temperature sintering. Techniques for machining, cleaning, and welding Nb-1 percent Zr cladding components were developed. End caps were electron beam welded to the tubing. Helium back-fill holes were sealed with a laser weld.

Mason, Richard E.↗
NASA NTRS2007

High Temperature Protonic Conductors

High Temperature Protonic Conductors (HTPC) with the perovskite structure are envisioned for electrochemical membrane applications such as H2 separation, H2 sensors and fuel cells. Successive membrane commercialization is dependent upon addressing issues with H2 permeation rate and environmental stability with CO2 and H2O. HTPC membranes are conventionally fabricated by solid-state sintering. Grain boundaries and the presence of intergranular second phases reduce the proton mobility by orders of magnitude than the bulk crystalline grain. To enhanced protonic mobility, alternative processing routes were evaluated. A laser melt modulation (LMM) process was utilized to fabricate bulk samples, while pulsed laser deposition (PLD) was utilized to fabricate thin film membranes . Sr3Ca(1+x)Nb(2-x)O9 and SrCe(1-x)Y(x)O3 bulk samples were fabricated by LMM. Thin film BaCe(0.85)Y(0.15)O3 membranes were fabricated by PLD on porous substrates. Electron microscopy with chemical mapping was done to characterize the resultant microstructures. High temperature protonic conduction was measured by impedance spectroscopy in wet air or H2 environments. The results demonstrate the advantage of thin film membranes to thick membranes but also reveal the negative impact of defects or nanoscale domains on protonic conductivity.

Dynys, Fred↗