Search NASA⌕ Search

SEARCH · Search NASA

Results for “natural laminar flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Comparison of predicted and measured drag for a single-engine airplane

Renewed interest in natural laminar flow (NLF) has rekindled designers' concerns that manufacturing deviations, (loss of surface contours or other surface imperfections) may destroy the effectiveness of NLF for an operational airplane. This paper reports on experimental research that compares predicted and measured boundary layer transition, total drag, and two-dimensional drag coefficients for three different wing surface conditions on an airplane typical of general aviation manufacturing technology. The three flight test phases included: (1) assessment of an unpainted airframe, (2) flight tests of the same airplane after painstakingly filling and sanding the wings to design contours, and (3) similar measurements after this airplane was painted. In each flight phase, transition locations were monitored using either sublimating chemicals or pigmented oil. As expected, total drag changes were difficult to measure. Two-dimensional drag coefficients were estimated using the Eppler-Somers code and measured with a wake rake in a method very similar to Jones' pitot traverse method. The net change in two-dimensional drag was approximately 20 counts between the unpainted airplane and the 'hand-smoothed' airplane for typical cruise flight conditions.

Ward, D. T.↗
NASA NTRS1985

Computational wing design in support of an NLF variable sweep transition flight experiment

A natural laminar flow outer panel wing glove has been designed for a variable sweep fighter aircraft using state-of-the-art computational techniques. Testing of the design will yield wing pressure and boundary-layer data under actual flight conditions and environment. These data will be used to enhance the understanding of the interaction between crossflow and Tollmien-Schlichting disturbances on boundary-layer transition. The outer wing panel was contoured such that a wide range of favorable pressure gradients could be obtained on the wing upper surface. Extensive computations were performed to support the design effort which relied on two- and three-dimensional transonic design and analysis techniques. A detailed description of the design procedure that evolved during this study is presented. Results on intermediate designs at various stages in the design process demonstrate how the various physical and aerodynamic constraints were integrated into the design. Final results of the glove design analyzed as part of the complete aircraft configuration with a full-potential wing/body analysis code indicate that the aerodynamic design objectives were met.

Waggoner, E. G.↗
NASA NTRS1986

Shaping of airplane fuselages for minimum drag

The VSAERO surface panel method is employed to investigate fuselage shapes which can enhance the natural laminar flow (NLF) characteristics. The study is performed at cruise Re which are relevant to commuter, transport, and business aircraft. The technique is based on piecewise constant doublet and source singularities and takes into account the effects of compressibility. Inviscid pressure distributions were generated for five configurations to aid in the search for an optimized NLF body shape as a function of the transition locations and the drag coefficients. Granville's transition criteria are incorporated into the calculations to yield shapes with longer runs of laminar flow and reduced drag. In comparison with other transition prediction methods, the method described is shown to have significantly higher valicity for making three-dimensional transition predictions.

Dodbele, S. S.↗
NASA NTRS1985

Swept wing-tip shapes for low-speed airplanes

Preliminary results are presented of a study conducted to analyze the effects of several plan-form modifications on the aerodynamic characteristics of a high-aspect-ratio, natural laminar flow (NLW) wing. The study addresses the potential aerodynamic improvements available at both cruise and high angles of attack by use os swept wing-tip shapes. The swept wing tip appears to offer a viable addition to the lift of wing-tip designs which provide improvements in aerodynamic efficiency, with the added safety benefit of providing high angle-of-attack departure resistance.

Van Dam, C. P.↗
NASA NTRS1985

Leading-edge design for improved spin resistance of wings incorporating conventional and advanced airfoils

Discontinuous wing leading-edge droop designs have been evaluated as a means of modifying wing autorotative characteristics and thus improving airplane spin resistance. Addition of a discontinuous outboard wing leading-edge droop to three typical light airplanes having NACA 6-series wing sections produced significant improvements in stall characteristics and spin resistance. Wind tunnel tests of two wings having advanced natural laminar flow airfoil sections indicated that a discontinuous leading-edge droop can delay the onset of autorotation at high angles of attack without adversely affecting the development of laminar flow at cruise angles of attack.

Stough, H. P., III↗
NASA NTRS1986

Boundary-layer stability and airfoil design

Several different natural laminar flow (NLF) airfoils have been analyzed for stability of the laminar boundary layer using linear stability codes. The NLF airfoils analyzed come from three different design conditions: incompressible; compressible with no sweep; and compressible with sweep. Some of the design problems are discussed, concentrating on those problems associated with keeping the boundary layer laminar. Also, there is a discussion on how a linear stability analysis was effectively used to improve the design for some of the airfoils.

Viken, Jeffrey K.↗
NASA NTRS1986

Manufacturing requirements

In recent years, natural laminar flow (NLF) has been proven to be achievable on modern smooth airframe surfaces over a range of cruise flight conditions representative of most current business and commuter aircraft. Published waviness and boundary layer transition measurements on several modern metal and composite airframes have demonstrated the fact that achievable surface waviness is readily compatible with laminar flow requirements. Currently, the principal challenge to the manufacture of NLF-compatible surfaces is two-dimensional roughness in the form of steps and gaps at structural joints. Results of recent NASA investigations on manufacturing tolerances for NLF surfaces, including results of a flight experiment are given. Based on recent research, recommendations are given for conservative manufacturing tolerances for waviness and shaped steps.

Holmes, Bruce J.↗
NASA NTRS1988

NLF technology is ready to go

Natural laminar flow (NLF) can reduce drag on aircraft developed using modern structural design methods. Modern metal and composite construction methods can meet NLF requirements for subsonic commuter and business airframes. NLF research at NASA concentrates on expanding the practical application of NLF drag reduction technology; payoffs include progress with liquid-crystal flow visualization, NLF on three-dimensional bodies, and the effects of acoustics on laminar stability. Fuel savings from 2 to 4 percent are expected if laminar flow could be achieved over the forward 50 percent of engine nacelles on large transports depending on the configuration. It is concluded that the skill required to use NLF for drag reduction depends on understanding the conservative design corridors within which laminar flow is durable and reliable.

Holmes, Bruce J.↗
NASA NTRS1987

Boundary-layer stability analysis of NLF and LFC experimental data at subsonic and transonic speeds

NASA-Lewis has conducted wind tunnel experiments to ascertain the effectiveness of state-of-the-art in natural laminar flow (NLF) and LFC airfoils for subsonic and transonic speeds, such as the NLF(1)-0414F and the SCLFC(1)-0513F. Attention is given to the effects of Tollmien-Schlichting (TS) and/or crossflow linear mechanisms amplifying small disturbances to generate turbulence. It is found that the incompressible TS transitional n-factors were generally in the 9-12 range, in agreement with earlier correlation studies; the TS instability was the dominant instability mode on a swept-planform LFC airfoil over the entire range of test conditions.

Berry, Scott A.↗
NASA NTRS1987

Theoretical investigations, and correlative studies for NLF, HLFC, and LFC swept wings at subsonic, transonic and supersonic speeds

Attention is given to the results of theory/experiment-correlation studies for natural laminar flow, LFC, and hybrid-LFC airfoils at subsonic and supersonic Mach numbers. The method of characteristics, integral compressible boundary layer methods for infinitely swept wings, and a method for prediction of separating turbulent boundary layer characteristics. The integral boundary layer methods are found to be successful at predicting both transonic and supersonic transition phenomena. Computations for wings with 0-50 deg sweep angle, Reynolds number range of 1-30 million, and with and without LFC, are in good agreement with experimental data.

Goradia, S. H.↗
NASA NTRS1987

Theoretical methods and design studies for NLF and HLFC swept wings at subsonic and supersonic speeds

Laminarization of the boundary layer on the surface of aircraft wings can be accomplished by the use of concepts such as Natural Laminar Flow (NLF), Laminar-Flow Control (LFC), and Hybrid Laminar-Flow Control (HLFC). Several integral boundary-layer methods were developed for the prediction of laminar, transition, and separating turbulent boundary layers. These methods were developed for use at either subsonic or supersonic speeds, have small computer execution times, and are simple to use. The theoretical equations and assumptions which form the basis of the boundary-layer method, are briefly outlined and the results of several correlation cases with exciting experimental data are presented.

Goradia, Suresh H.↗
NASA NTRS1987

Design of the low-speed NLF(1)-0414F and the high-speed HSNLF(1)-0213 airfoils with high-lift systems

The design and testing of Natural Laminar Flow (NLF) airfoils is examined. The NLF airfoil was designed for low speed, having a low profile drag at high chord Reynolds numbers. The success of the low speed NLF airfoil sparked interest in a high speed NLF airfoil applied to a single engine business jet with an unswept wing. Work was also conducted on the two dimensional flap design. The airfoil was decambered by removing the aft loading, however, high design Mach numbers are possible by increasing the aft loading and reducing the camber overall on the airfoil. This approach would also allow for flatter acceleration regions which are more stabilizing for cross flow disturbances. Sweep could then be used to increase the design Mach number to a higher value also. There would be some degradation of high lift by decambering the airfoil overall, and this aspect would have to be considered in a final design.

Viken, Jeffrey K.↗
NASA NTRS1990

Effects of forebody geometry on subsonic boundary-layer stability

As part of an effort to develop computational techniques for design of natural laminar flow fuselages, a computational study was made of the effect of forebody geometry on laminar boundary layer stability on axisymmetric body shapes. The effects of nose radius on the stability of the incompressible laminar boundary layer was computationally investigated using linear stability theory for body length Reynolds numbers representative of small and medium-sized airplanes. The steepness of the pressure gradient and the value of the minimum pressure (both functions of fineness ratio) govern the stability of laminar flow possible on an axisymmetric body at a given Reynolds number. It was found that to keep the laminar boundary layer stable for extended lengths, it is important to have a small nose radius. However, nose shapes with extremely small nose radii produce large pressure peaks at off-design angles of attack and can produce vortices which would adversely affect transition.

Dodbele, Simha S.↗
NASA NTRS1991

Laminar-Separation Sensor

Reduction of viscous drag on airplanes explores limits of practical applications of natural laminar flow. Wind-tunnel and flight tests conducted to explore abilities of hot-film sensors to identify separation of laminar flow as principal mode of amplification of instability leading to transition from laminar to turbulent flow. Two different laminar-separation-sensor configurations developed and used to detect boundary-layer transitions. Results show hot-film laminar-separation-sensor technique viable means for detecting existence of transition as well as for indicating reversed flow in laminar-separation bubble. Refinement of sensor configurations provides tools necessary to explore, in all speed regimes, practical limits of laminar-flow applications and viscous-drag-reduction technology.

Manuel, G. S.↗
NASA NTRS1991

Future regional/commuter challenges

Technological advances in the next ten years will represent a continuum of the steady improving state-of-the-art in all the major disciplines. In the past there was a number of step changes in technology, but no known really large quantum jumps are envisioned at present which could be readily applied to short haul aircraft. The one exception in the field of aerodynamics might be the application of natural laminar flow on short haul and laminar flow control on long haul aircraft. The aim in the 1990's will be to single out the major areas where advances will contribute to overcome important constraints such as fuel conservation, noise, airspace and airport saturation, and surface transportation competition.

Harvey, W. Don↗
NASA NTRS1991

Design limits of compressible NLF airfoils

There has been considerable success in the design of practical low-speed natural laminar flow (NLF) airfoils, with significant profile drag reduction from conventional turbulent flow airfoils. The favorable lowspeed results give an incentive to explore the possibilities of high-subsonic speed NLF airfoil design. The design problem at higher freestream Mach numbers is more severe than for low-speed designs because these high-speed airplanes typically fly at higher chord Reynolds numbers than low-speed NLF airplanes. As the Mach number increases, the main priority changes from the use of sufficient acceleration to achieve NLF for low-drag, to the delay of separation in the far aft pressure recovery region. In this effort, NLF airfoils have been designed for Mach numbers ranging from 0.60 to 0.80 and chord Reynolds numbers of 30 x 10 to the 6th and 40 x 10 to the 6th.

Viken, Jeff↗
NASA NTRS1991

Preliminary design studies of an advanced general aviation aircraft

The preliminary design results are presented of the advanced aircraft design project. The goal was to take a revolutionary look into the design of a general aviation aircraft. Phase 1 of the project included the preliminary design of two configurations, a pusher, and a tractor. Phase 2 included the selection of only one configuration for further study. The pusher configuration was selected on the basis of performance characteristics, cabin noise, natural laminar flow, and system layouts. The design was then iterated to achieve higher levels of performance.

Barrett, Ron↗
NASA NTRS1993

Numerical prediction of transition of the F-16 wing at supersonic speeds

A parametric study is being conducted as an effort to numerically predict the extent of natural laminar flow (NLF) on finite swept wings at supersonic speeds. This study is one aspect of a High Speed Research Program (HSRP) to gain an understanding of the technical requirements for high-speed aircraft flight. The parameters that are being addressed in this study are Reynolds number, angle of attack, and leading-edge wing sweep. These parameters were analyzed through the use of an advanced Computational Fluid Dynamics (CFD) flow solver, specifically the ARC 3-D Compressible Navier-Stokes (CNS) flow solver. From the CNS code, pressure coefficients (Cp) are obtained for the various cases. These Cp's are then used to compute the boundary-layer profiles through the use of the 'Kaups and Cebeci' compressible 2-D boundary layer code. Finally, the boundary-layer parameters are processed into a 3-D compressible boundary layer stability code (COSAL) to predict transition. The parametric study then consisted of four geometries which addressed the effects of sweep, and three angles of attack from zero to ten degrees to yield a total of 12 cases. The above process was substantially automated through a procedure that was developed by the work conducted under this study. This automation procedure then yields a 3-D graphical measure of the extent of laminar flow by predicting the transition location of laminar to turbulent flow.

Cummings, Russell M.↗