Search NASA⌕ Search

SEARCH · Search NASA

Results for “new battery cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Asymmetric ether solvents for high-rate lithium metal batteries

Recent electrolyte solvent design based on weakening lithium-ion solvation have shown promise in enhancing cycling performance of Li-metal batteries. However, they often face slow redox kinetics and poor cycling reversibility at high rate. Here we report using asymmetric solvent molecules substantially accelerates Li redox kinetics. Asymmetric ethers (1-ethoxy-2-methoxyethane, 1-methoxy-2-propoxyethane) showed higher exchange current densities and enhanced high-rate Li 0 plating/stripping reversibility compared to symmetric ethers. Adjusting fluorination levels further improved oxidative stability and Li 0 reversibility. The asymmetric 1-(2,2,2-trifluoro)-ethoxy-2-methoxyethane, with 2 M lithium bis(fluorosulfonyl)imide, exhibited high exchange current density, oxidative stability, compact solid–electrolyte interphase (~10 nm). This electrolyte exhibited superior performance among state-of-the-art electrolytes, enabling over 220 cycles in high-rate Li (50 μm)||LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811, 4.9 mAh cm −2 ) cells and for the first time over 600 cycles in anode-free Cu | |Ni95 pouch cells (200 mAh) under electric vertical take-off and landing cycling protocols. Our findings on asymmetric molecular design strategy points to a new pathway towards achieving fast redox kinetics for high-power Li-metal batteries.

batteries↗
DOE OSTI2020

HPC4Mfg with Sepion

We employed ab-initio simulations and quantum chemical calculations to develop a computational framework for simulating the microscopic structure and mechanical properties of novel polymer membranes used in lithium sulfur batteries. To meet industry targets, next generation batteries with high specific energy (Wh/kg) are essential. Efforts to commercialize light-weight, energy-dense lithium-sulfur secondary batteries (2510 Wh/kg) have been stalled by ongoing problems with the battery’s separator membrane, which should prevent cross-over of active material from cathode to anode that, if unchecked, limits cycle-life. However, Sepion Technologies’ polymer membranes yield long-lasting lithium-sulfur cells. Advancing to 10 Ah battery prototypes, Sepion faces challenges in membrane manufacturing related to polymer processing and the molecular basis for membrane performance and durability. High performance computing offers critical new insight into these phenomena, which in turn will accelerate product entry into the market.

25 ENERGY STORAGE↗
DOE OSTI2021

Lithium Cyano Tris(2,2,2-trifluoroethyl) Borate as a Multifunctional Electrolyte Additive for High-Performance Lithium Metal Batteries

Lithium cyano tris(2,2,2-trifluoroethyl) borate (LCTFEB) has been synthesized and investigated as a new electrolyte additive for high performance of lithium metal batteries. LCTFEB is prepared by the reaction of tris(2,2,2-trifluoroethyl) borate with lithium cyanide. Incorporation of LCTFEB into carbonate-based electrolyte has been investigated. The electrochemical performance of NCM523/Li cells as well as symmetric Li/Li cells are significantly improved upon incorporation of LCTFEB (5 wt.%) into the electrolyte. Various characterizations of lithium metal morphology and the solid electrolyte interphase (SEI) on the lithium metal anode have been conducted using by FE-SEM, cryo-TEM and XPS suggesting the generation of a thin (≈ 10 nm) LiF rich SEI with low concentrations of B and N-compounds. The different SEI structure is formed by the preferential reductive decomposition of LCTFEB resulting in improved electrochemical performance. As a result, the new electrolyte additive provides insight into innovative approaches for multi-functional electrolyte additive design.

25 ENERGY STORAGE↗
DOE OSTI2021

I.6.C Battery Safety Testing

Abuse tests are designed to determine the safe operating limits of HEV\PHEV energy storage devices. Testing is intended to achieve certain worst-case scenarios to yield quantitative data on cell\module\pack response, allowing for failure mode determination and guiding developers toward improved materials and designs. Standard abuse tests with defined start and end conditions are performed on all devices to provide comparison between technologies. New tests and protocols are developed and evaluated to more closely simulate real world failure conditions. While robust mechanical models for vehicles and vehicle components exist, there is a gap for mechanical modeling of EV batteries. The challenge with developing a mechanical model for a battery is the heterogeneous nature of the materials and components (polymers, metals, metal oxides, liquids).

25 ENERGY STORAGE↗
DOE OSTI2022

Solvent-Free Manufacturing of Lithium-Ion Battery Electrodes via Cold Plasma

Slurry casting has been used to fabricate lithium-ion battery electrodes for decades, which involves toxic and expensive organic solvents followed by high-cost vacuum drying and electrode calendering. This work presents a new manufacturing method using a nonthermal plasma to create inter-particle binding without using any polymeric binding materials, enabling solvent-free manufacturing electrodes with any electrochemistry of choice. The cold-plasma-coating technique enables fabricating electrodes with thickness (>200 μm), high mass loading (>30 mg cm -2 ), high peel strength, and the ability to print lithium-ion batteries in an arbitrary geometry. This crosscutting, chemistry agnostic, platform technology would increase energy density, eliminate the use of solvents, vacuum drying, and calendering processes during production, and reduce manufacturing cost for current and future cell designs. Here, lithium iron phosphate and lithium cobalt oxide were used as examples to demonstrate the efficacy of the cold-plasma-coating technique. It is found that the mechanical peel strength of cold-plasma-coating-manufactured lithium iron phosphate is over an order of magnitude higher than that of slurry-casted lithium iron phosphate electrodes. Full cells assembled with a graphite anode and the cold-plasma-coating-lithium iron phosphate cathode offer highly reversible cycling performance with a capacity retention of 81.6% over 500 cycles. For the highly conductive cathode material lithium cobalt oxide, an areal capacity of 4.2 mAh cm -2 at 0.2 C is attained. We anticipate that this new, highly scalable manufacturing technique will redefine global lithium-ion battery manufacturing providing significantly reduced plant footprints and material costs.

25 ENERGY STORAGE↗
DOE OSTI2024

CRADA Final Report: Ultralong Cycle Life and Ultrafast Charging Batteries to Electrify High Duty-Cycle, Mobile Platforms

As part of the Cyclotron Road program, Tyfast Energy Corp. aimed to investigate the Li 3 V 2 O 5 (LVO) anode material for next generation lithium batteries. State of the art and fast charging lithium-ion batteries are based on the lithium titanate or Li 4 Ti 5 O 12 (LTO) anode chemistry. LTO cells demonstrate fast charging times (<6 mins), long cycle life (>20,000 cycles), but at the expense of very low energy density (<200Wh/L, <80Wh/kg). Silicon anodes have the promise of achieving fast charging times, however, issues with cycling stability in combination with fast charging is unknown. LVO has unique properties that enable new performance window for lithium batteries. First, LVO operates at an average potential of 0.6V vs. Li/Li + , well above the Li-metal plating region allowing ultrafast charge capability without sacrificing safety. Second, the LVO has a high specific capacity of 250 mAh/g making battery pack energy density equivalent with current high-energy Li-ion chemistries.

25 ENERGY STORAGE↗
DOE OSTI2026

Roadmap on advanced and / real-time characterisation of solid state materials and devices for energy applications

A strong societal and political drive is motivating the development and optimization of novel energy conversion and storage systems for decarbonization. The successful implementation of solid state devices such as fuel cells and secondary batteries depends, however, on achieving ambitious targets in terms of performance, reliability and cost competitiveness. Research and technology are addressing these needs through a holistic approach including exploration of new materials and nanoarchitectures, as well as system engineering. These significant efforts require the support of appropriate characterization tools capable of assessing nanometer-scale phenomena such as concentration profiles of ionic and electronic charges, local chemical compositions and their evolution over time across interfaces. This roadmap provides an overview of selected advanced characterization techniques for energy materials and devices. Specific focus is put on in situ/operando methods for probing electrochemical phenomena in real-time under realistic working conditions. Experts in the field provide an extensive review of the current state of the art in 2025 and the current and future challenges for the characterization of local chemistry and kinetics in the bulk of the material, in nanoarchitectures (e.g. thin films) and at the interfaces (e.g. grain boundaries, phase contacts, solid/liquid and solid/gas interfaces) . The aim is to provide a detailed guide to the techniques, describing opportunities and bottlenecks for their practical deployment and examples of successful applications.

25 ENERGY STORAGE↗
DOE OSTI2024

Leveraging Temperature-Dependent (Electro)Chemical Kinetics for High-Throughput Flow Battery Characterization

The library of redox-active organics that are potential candidates for electrochemical energy storage in flow batteries is exceedingly vast, necessitating high-throughput characterization of molecular lifetimes. Demonstrated extremely stable chemistries require accurate yet rapid cell cycling tests, a demand often frustrated by time-denominated capacity fade mechanisms. We have developed a high-throughput setup for elevated temperature cycling of redox flow batteries, providing a new dimension in characterization parameter space to explore. We utilize it to evaluate capacity fade rates of aqueous redox-active organic molecules, as functions of temperature. We demonstrate Arrhenius-like behavior in the temporal capacity fade rates of multiple flow battery electrolytes, permitting extrapolation to lower operating temperatures. Collectively, these results highlight the importance of accelerated decomposition protocols to expedite the screening process of candidate molecules for long lifetime flow batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Shorting at Long Duration: Impact of Extended Discharge Capacity on Battery Solid Electrolytes

Long-duration energy storage (LDES) is critical to a stable, resilient, and decarbonized electric grid. While batteries are emerging as important LDES devices, extended, high-power discharges necessary for cost-competitive LDES present new materials challenges. Here, focusing on a new generation of low-temperature molten sodium batteries, we explore here unique phenomena related to long-duration discharge through a well-known solid electrolyte, NaSICON. Specifically, molten sodium symmetric cells at 110°C were cycled at 0.1 A cm -2 for 1-23 h discharges. Longer discharges led to unstable overpotentials, reduced resistances, and decreased electrolyte strength, caused by massive sodium penetration not observed in shorter duration discharges. Scanning electron microscopy informed mechanisms of sodium penetration and even “healing” during shorter-duration cycling. Importantly, these findings show that traditional, low-capacity, shorter-duration tests may not sufficiently inform fundamental materials phenomena that will impact LDES battery performance. This case highlights the importance that candidate LDES batteries be tested under pertinent long-duration conditions.

25 ENERGY STORAGE↗
NASA NTRS1977

The standard 20 AH battery

The modular power system, which is the first intended use for the NASA standard battery, is basically a four foot by four foot by eighteen inch box which can handle a complement of three 20 ampere hour batteries or later on the intended use is for three 50 ampere hour batteries to be the full complement. The system is designed to be used as a plug on component on a multi mission modular spacecraft. It has as a design point a basically 1250 watt orbital average load. The way it breaks up in a near earth orbit it would be somewhere around 1,000 watts for everything except 10 minutes, and during any 10 minute period it may go up to a peak of 3,000 watt load. Features of the battery reviewed include criteria to store electrical energy, the battery package, the covers and cases, and electrolytes. The capacities expected are 90 percent, the average cell capacity for 24 C, 90 percent of the actual battery capacity of 19 C, and 85 percent of the actual 25 degree battery capacity at zero discharge voltage for 50 percent DOD new battery is in the vicinity expected or predicted of 26.4 volts.

Zollner, M. T.↗
NASA NTRS1995

Space Electrochemical Research and Technology. Abstracts

This document contains abstracts of the proceedings of NASA's fifth Space Electrochemical Research and Technology (SERT) Conference, held at the NASA Lewis Research Center on May 1-3, 1995. The objective of the conference was to assess the present status and general thrust of research and development in those areas of electrochemical technology required to enable NASA missions into the next century. The conference provided a forum for the exchange of ideas and opinions of those actively involved in the field, in order to define new opportunities for the application of electrochemical processes in future NASA missions. Papers were presented in three technical areas: (1) the electrochemical interface, (2) the next generation in aerospace batteries and fuel cells, and (3) electrochemistry for non-energy storage applications. This document contains the abstracts of the papers presented.

Source record↗
DOE OSTI2020

Battery Abuse Testing

Abuse tests are designed to determine the safe operating limits of HEV\PHEV energy storage devices. Testing is intended to achieve certain worst-case scenarios to yield quantitative data on cell\module\pack response, allowing for failure mode determination and guiding developers toward improved materials and designs. Standard abuse tests with defined start and end conditions are performed on all devices to provide comparison between technologies. New tests and protocols are developed and evaluated to more closely simulate real-world failure conditions. While robust mechanical models for vehicles and vehicle components exist, there is a gap for mechanical modeling of EV batteries. The challenge with developing a mechanical model for a battery is the heterogeneous nature of the materials and components (polymers, metals, metal oxides, liquids). This year saw the stand up of a new drop tower tester capable of providing dynamic mechanical test results.

25 ENERGY STORAGE↗
NASA NTRS2003

Structure of Thin-Film Lithium Microbatteries

A process for making thin-film batteries including the steps of cleaning a glass or silicon substrate having an amorphous oxide layer several microns thick; defining with a mask the layer shape when depositing cobalt as an adhesion layer and platinum as a current collector; using the same mask as the preceding step to sputter a layer of LiC(0)O2, on the structure while rocking it back and forth; heating the substrate to 300 C. for 30 minutes; sputtering with a new mask that defines the necessary electrolyte area; evaporating lithium metal anodes using an appropriate shadow mask; and, packaging the cell in a dry-room environment by applying a continuous bead of epoxy around the active cell areas and resting a glass slide over the top thereof. The batteries produced by the above process are disclosed.

Jay F Whitacre↗
DOE OSTI2025

Fast-charging lithium-ion batteries: Synergy of carbon nanotubes and laser ablation

Advancing lithium-ion battery (LiB) technology to achieve 10–15-min extreme fast charging (XFC) while maintaining high energy density and longevity poses a significant challenge. Addressing Li-plating is crucial, as it depletes useable Li, causing deterioration and safety issues. Here, this study explores a holistic approach incorporating Single-Wall Carbon Nanotubes (SWCNTs) and Laser Ablation (LA) to mitigate Li-plating while maintaining high charge acceptance under 10–15-min XFC. SWCNTs enhance the electrical conductivity and mechanical integrity of the positive electrode (PE), reducing overall cell overpotential at high charging rates. Concurrently, LA is applied to negative electrodes (NE) to reduce tortuosity of ion-diffusion pathways and increase surface wettability, improving Li-ion transport. Combining SWCNTs in the PE and LA on the NE, our experimental findings demonstrate a significant reduction in Li-plating and maintained high charge acceptance of ~84.33 % after 800 5C (12 min) charge cycles for cells having PE with ~3.3 mAh cm –2 and NE with 3.9 mAh cm –2 loadings. This study highlights the potential of combining SWCNTs and LA to address Li-plating in LiBs and opens new avenues for designing battery systems capable of achieving 10–15-min XFC.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Unlocking High Capacity and Reversible Alkaline Iron Redox Using Silicate-Sodium Hydroxide Hybrid Electrolytes

Alkaline iron (Fe) batteries are attractive due to the high abundance, low cost, and multiple valent states of Fe but show limited columbic efficiency and storage capacity when forming electrochemically inert Fe 3 O 4 on discharging and parasitic H 2 on charging. Herein, sodium silicate is found to promote Fe(OH) 2 /FeOOH against Fe(OH) 2 /Fe 3 O 4 conversions. Electrochemical experiments, operando X-ray characterization, and atomistic simulations reveal that improved Fe(OH) 2 /FeOOH conversion originates from (i) strong interaction between sodium silicate and iron oxide and (ii) silicate-induced strengthening of hydrogen-bond networks in electrolytes that inhibits water transport. Furthermore, the silicate additive suppresses hydrogen evolution by impairing energetics of water dissociation and hydroxyl de-sorption on iron surfaces. In conclusion, this new silicate-assisted redox chemistry mitigates H 2 and Fe 3 O 4 formation, improving storage capacity (199 mAh g -1 in half-cells) and coulombic efficiency (94 % after 400 full-cell cycles), paving a path to realizing green battery systems built from earth-abundant materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Unraveling the convoluted and dynamic interphasial mechanisms on Li metal anode

Accurate understanding of the chemistry of solid-electrolyte interphase (SEI) is key to developing new electrolytes for high-energy batteries using lithium metal (Li-0) anodes(1). SEI is generally believed to be formed by the reactions between Li-0 and electrolyte(2,3). However, our new study shows this is not the whole story. Through synchrotron-based X-ray diffraction and pair distribution function analysis, we reveal a much more convoluted formation mechanism of SEI, which receives considerable contributions from electrolyte, cathode, moisture and native surface species on Li-0, with highly dynamic nature during cycling. Using isotope labelling, we traced the origin of LiH to electrolyte solvent, moisture and a new source: the native surface species (LiOH) on pristine Li-0. When lithium accessibility is very limited as in the case of anode-free cells, LiOH develops into plate-shaped large crystals during cycling. Alternatively, when the lithium source is abundant, as in the case of Li||NMC811 cells, LiOH reacts with Li-0 to form LiH and Li2O. While the desired anion-derived LiF-rich SEI is typically found in the concentrated electrolytes or their derivatives, we found it can also be formed in low-concentration electrolyte via the crosstalk effect, emphasizing the importance of formation cycle protocol and opening up opportunities for low-cost electrolyte development.

Polzin, Bryant J.↗
DOE OSTI2021

New High-Energy & Safe Battery Technology with Extreme Fast Charging Capability for Automotive Applications (Final Technical Report)

Being able to refill a cars gas tank when low on fuel is incredibly convenient and is a lacking feature for battery elective vehicles. New High-Energy & Safe Battery Technology with Extreme Fast Charging Capability for Automotive Applications was a research project designed to help correct this lacking feature by developing automotive sized Li-ion battery cells and demonstrating their ability to charge in under 10-minutes. To address the technical challenges Microvast, a cell manufacturer, was joined by Argonne National Labs, battery technology innovator, and BMW, a renown OEM, worked together to define and validate materials and cells for this project. By projects end, Microvast had successfully built and demonstrated a 240 Wh/kg, 35 Ah pouch cell that was capable of over 800 10-minute charge, full discharge cycles. From the outset of the project the plan was to use large amp-hour cells (ie automotive relevant sizes) to ensure the project findings and outcomes were most relevant for electric vehicle applications. The manufacture of cells was done using test manufacturing lines at Microvast and BMW that closely resemble the procedures of a Li-ion battery cell factory.

25 ENERGY STORAGE↗
DOE OSTI2023

Aerosol Manufacturing Technology to Produce Low-Cobalt Li-ion Battery Cathodes

Although considerable progress has been made with battery materials over the last 10 years, the cathode remains a major performance-limiting material in Li-ion battery (LIB) technology. New materials and battery chemistries will overcome some of the remaining challenges, but cathode materials must also be manufactured at a lower cost and with a smaller environmental footprint using new processes that can also enable improved control over stoichiometry, morphology, and compositional homogeneity. Cabot, Argonne National Laboratory and SAFT research teams are combining their extensive expertise in particle synthesis, battery materials and cell design to develop a low-cost, flexible aerosol manufacturing technology for production of high-performance cathode active materials (CAM). This project will develop low-Co CAMs via Reactive Spray Technology (RST) and Flame Spray Pyrolysis (FSP) to reach performance targets of < 50 mg Cobalt/Wh.

25 ENERGY STORAGE↗