Search NASA⌕ Search

SEARCH · Search NASA

Results for “operating system interference”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Performance of traffic-alert collision avoidance (TCAS) antennas in the presence of scatterers

The performance of two TCAS systems is studied in the presence of electromagnetic scatterers. TCAS is an aircraft mounted angle of arrival (AOA) system, which estimates the bearing of a signal transmitted from a mode-S transponder on another nearby aircraft (intruder). Two systems are studied: (1) Comparison of Relative Amplitude system (CRA), and (2) Spiral Phase Antenna (SPA). The CRA antenna receives the reply via four switched beams. The bearing is estimated by comparing the amplitudes of the received signal. The SPA is based on the phase interferometer, which utilizes the received phase via sum and difference beams. The AOA is computed by comparing the reply with similar values on a calibration table, which is generated by modeling the TCAS antenna on the bare fuselage of a Boeing 727-200. The antenna patterns for the TCAS are found via high frequency methods based on the Uniform Geometric theory of Diffraction (UTD). By minimizing the standard deviation of the bearing error in a specified angular sector, optimal locations for top and bottom mounted TCAS antennas are found on the Boeing 727-200, 737-300 and 747-200 airframes. It will be shown that the overall bearing errors of the amplitude system are consistently smaller than the spiral phase TCAS. The effect of two types of nearby scatterers--antennas, and engine inlets--is studied. The AT741 L-band blade, DMC60-1 VHF Communication antenna were chosen as being representative antenna interference examples. Models are derived for the blades via a moment method analysis followed by a least squares procedure to synthesize the scattering patterns. Studies were conducted to estimate the minimum separation between the two antennas for acceptable operation. It will be shown that the spiral phase TCAS is adversely affected by the presence of a blade antenna. The amplitude system does not suffer from this limitation, especially for the forward look angles which are of most interest here. A model to represent the inlet scattering is based on the multiple scattering method and UTD. The engine on top of the B727-200 fuselage is modeled by a terminated circular waveguide. Then, the effect of moving the antenna forward on the fuselage is studied. It is again shown that the performance of the amplitude system is superior.

Sampath, K. S.↗

Laser angle measurement system

The design and fabrication of a laser angle measurement system is described. The instrument is a fringe counting interferometer that monitors the pitch attitude of a model in a wind tunnel. A laser source and detector are mounted above the mode. Interference fringes are generated by a small passive element on the model. The fringe count is accumulated and displayed by a processor in the wind tunnel control room. Optical and electrical schematics, system maintenance and operation procedures are included, and the results of a demonstration test are given.

Pond, C. R.↗

Mitigation of Laser Beam Scintillation in Free-Space Optical Communication Systems Through Coherence-Reducing Optical Materials

Free-space optical communication systems (also known as lasercom systems) offer several performance advantages over traditional radio frequency communication systems. These advantages include increased data rates and reduced operating power and system weight. One serious limiting factor in a lasercom system is Optical turbulence in Earth's atmosphere. This turbulence breaks up the laser beam used to transmit the information into multiple segments that interfere with each other when the beam is focused onto the receiver. This interference pattern at the receiver changes with time causing fluctuations in the received optical intensity (scintillation). Scintillation leads to intermittent losses of the signal and an overall reduction in the lasercom system's performance. Since scintillation is a coherent effect, reducing the spatial and temporal coherence of the laser beam will reduce the scintillation. Transmitting a laser beam through certain materials is thought to reduce its coherence. Materials that were tested included: sapphire, BK7 glass, fused silica and others. The spatial and temporal coherence of the laser beam was determined by examining the interference patterns (fringes) it formed when interacting with various interferometers and etalons.

Renner, Christoffer J.↗

The Behavior of PCM/PM Receivers in Non-Ideal Channels

This paper presents a performance evaluation of residual carrier commuication systems that employ a PCM/PM modulation technique operating over non-ideal channels. The non-ideal channels under investigation include data asymmetry, an unbalanced data stream (i.e., transition density deviates from 0.5) and InterSymbol Interference (ISI).

InterSymbol Interference↗

Development and Operations of the Astrophysics Data System

SAO TASKS ACCOMPLISHED: Abstract Service: (1) Continued regular updates of abstracts in the databases, both at SAO and at all mirror sites; (2) Established a new naming convention of QB books in preparation for adding physics books from Hollis or Library of Congress; (3) Modified handling of object tag so as not to interfere with XHTML definition; (4) Worked on moving 'what's new' announcements to a majordomo email list so as not to interfere with divisional mail handling; (5) Implemented and tested new first author feature following suggestions from users at the AAS meeting; (6) Added SSRv entries back to volume 1 in preparation for scanning of the journal; (7) Assisted in the re-configuration of the ADS mirror site at the CDS and sent a new set of tapes containing article data to allow re-creation of the ADS article data lost during the move; (8) Created scripts to automatically download Astrobiology.

Murray, Stephen S.↗

Challenges of Space Mission Interoperability

This viewgraph presentation reviews some of the international challenges to space mission interoperability. Interoperability is the technical capability of two or more systems or components to exchange information and to use the information that has been exchanged. One of the challenges that is addressed is the problem of spectrum bandwidth, and interference. The key to interoperability is the standardization of space communications services and protocols. Various levels of international cross support are reviewed: harmony, cooperation cross support and confederation cross support. The various international bodies charged with implementing cross support are reviewed. The goal of the Interagency Operations Advisory Group (IOAG) is to achieve plug-and-play operations where all that is required is for each of the systems to use an agreed communications medium, after which the systems configure each other for the purpose of exchanging information and subsequently effect such exchange automatically.

interoperability↗

Control Synthesis for a Class of Hybrid Systems Subject to Configuration-Based Safety Constraints

We examine a class of hybrid systems which we call Composite Hybrid Machines (CHM's) that consists of the concurrent (and partially synchronized) operation of Elementary Hybrid Machines (EHM's). Legal behavior, specified by a set of illegal configurations that the CHM may not enter, is to be achieved by the concurrent operation of the CHM with a suitably designed legal controller. In the present paper we focus on the problem of synthesizing a legal controller, whenever such a controller exists. More specifically, we address the problem of synthesizing the minimally restrictive legal controller. A controller is minimally restrictive if, when composed to operate concurrently with another legal controller, it will never interfere with the operation of the other controller and, therefore, can be composed to operate concurrently with any other controller that may be designed to achieve liveness specifications or optimality requirements without the need to reinvestigate or reverify legality of the composite controller. We confine our attention to a special class of CHM's where system dynamics is rate-limited and legal guards are conjunctions or disjunctions of atomic formulas in the dynamic variables (of the type x less than or equal to x(sub 0), or x greater than or equal to x(sub 0)). We present an algorithm for synthesis of the minimally restrictive legal controller. We demonstrate our approach by synthesizing a minimally restrictive controller for a steam boiler (the verification of which recently received a great deal of attention).

Heymann, Michael↗

Causes and control of solar electric propulsion interactive effects

Contaminant effects and questions of thrust system operation status are discussed together with the sources of contaminant effects and the areas of contaminant impact. Contaminant reduction techniques are considered, giving attention to magnetic contamination, dc electric contamination, ac electric contamination, conducted EM interference, radio frequency interference, and material transport and deposition. Design goals for the reduction of contaminant levels are examined along with some areas of uncertainty.

Sellen, J. M., Jr.↗

Research on self-correcting wind tunnels

The Calspan self-correcting wind tunnel is a two-dimensional facility in which the flow field in the vicinity of the walls is actively controlled, and a theoretical evaluation is used in conjunction with flow field measurements to confirm that wall interference was minimized. The facility is described, and the results of experiments with a 6 percent-blockage model are presented to show that iterative application of wall control effectively eliminates the interference. Experiments were performed at conditions where the flow at the walls was supercritical, and a new operating procedure is described for these conditions. The results of an analysis of the flow in the auxiliary suction system and test ion illustrate the tradeoffs available in the design of self-correcting wind tunnel test sections and in model sizing for such tunnels.

Vidal, R. J.↗

An expert system for scheduling requests for communications Links between TDRSS and ERBS

An ERBS-TDRSS Contact Planning System (ERBS-TDRSS CPS) is described which uses a graphics interface and the NASA Transportable Interference Engine. The procedure involves transfer of the ERBS-TDRSS Ground Track Orbit Prediction data to the ERBS flight operations area, where the ERBS-TDRSS CPS automatically generates requests for TDRSS service. As requested events are rejected, alternative context sensitive strategies are employed to generate new requested events until a schedule is completed. A report generator builds schedule requests for separate ERBS-TDRSS contacts.

Mclean, David R.↗

Status of the NASA SETI Sky Survey microwave observing project

The Sky Survey observing program is one of two complementary strategies that NASA plans to use in its microwave Search for Extraterrestrial Intelligence (SETI). The primary objective of the Sky Survey is to search the entire sky over the frequency range 1000-10,000 MHz for evidence of narrow band signals of extraterrestrial, intelligent origin. Spectrum analyzers with upwards of 10 million channels and data rates in excess of 10 gigabits per second are required to complete the survey in less than 7 years. To lay the foundation for the operational SETI Sky Survey, a prototype system has been built to test and refine real time signal detection algorithms, to test scan strategies and observatory control functions, and to test algorithms designed to reject radio frequency interference. This paper presents a high level description of the prototype hardware and reports on the preparations to deploy the system to the 34-m antenna at the research and development station of NASA's Deep Space Communication Complex, Goldstone, California.

Klein, M. J.↗

Power connect safety and connection interlock

A power connect safety and connection interlock system is shown for use with inverters and other DC loads (16) which include capacitor filter banks (14) at their DC inputs. A safety circuit (20) operates a spring (26) biased, solenoid (22) driven mechanical connection interference (24) which prevents mating and therefore electrical connection between the power contactor halves (11, 13) of the main power contacts (12) until the capacitor bank is safely precharged through auxiliary contacts (18). When the DC load (16) is shut down, the capacitor bank (14) is automatically discharged through a discharging power resistor (66) by a MOSFET transistor (60) through a discharging power resistor (66) only when both the main power contacts and auxiliary contacts are disconnected.

Rippel, Wally E.↗

The effect of interference on delta modulation encoded video signals

An adaptive delta modulator which encodes composite color video signals was shown to provide a good response when operating at 16 Mb/s and near-commercial quality at 23Mb/s. The ADM was relatively immune to channel errors. The system design is discussed and circuit diagrams are included.

Schilling, D. L.↗

Space Station Technology Summary

The completion of the Space Station Propulsion Advanced Technology Programs established an in-depth data base for the baseline gaseous oxygen/gaseous hydrogen thruster, the waste gas resistojet, and the associated system operations. These efforts included testing of a full end-to-end system at National Aeronautics and Space Administration (NASA)-Marshall Space Flight Center (MSFC) in which oxygen and hydrogen were generated from water by electrolysis at 6.89 MPa (1,000 psia), stored and fired through the prototype thruster. Recent end-to-end system tests which generate the oxygen/hydrogen propellants by electrolysis of water at 20.67 MPa (3,000 psia) were completed on the Integrated Propulsion Test Article (IPTA) at NASA-Johnson Space Center (JSC). Resistojet testing has included 10,000 hours of life testing, plume characterization, and electromagnetic interference (EMI) testing. Extensive 25-lbf thruster testing was performed defining operating performance characteristics across the required mixture ratio and thrust level ranges. Life testing has accumulated 27 hours of operation on the prototype thruster. A total of seven injectors and five thrust chambers were fabricated to the same basic design. Five injectors and three thrust chambers designed to incorporate improved life, performance, and producibility characteristics are ready for testing. Five resistojets were fabricated and tested, with modifications made to improve producibility. The lessons learned in the area of producibility for both the O2/H2 thrusters and for the resistojet have resolved critical fabrication issues. The test results indicate that all major technology issues for long life and reliability for space station application were resolved.

Iacabucci, R.↗

Penetration of High Intensity Radiated Fields (HIRF) Into General Aviation Aircraft

The ability to design and achieve electromagnetic compatibility is becoming more challenging with the rapid development of new electronic products and technologies. The importance of electromagnetic interference (EMI) and electromagnetic compatibility (EMC) issues stems from the fact that the ambient electromagnetic environment has become very hostile; that is, it increases both in density and intensity, while the current trend in technology suggests the number of electronic devices increases in homes, businesses, factories, and transportation vehicles. Furthermore, the operating frequency of products coming into the market continuously increases. While cell phone technology has exceeded 1 GHz and Bluetooth operates at 2.4 GHz, products involving satellite communications operate near 10 GHz and automobile radar systems involve frequencies above 40 GHz. The concern about higher frequencies is that they correspond to smaller wavelengths, therefore electromagnetic waves are able to penetrate equipment enclosure through apertures or even small cracks more easily. In addition, electronic circuits have become small in size, and they are usually placed on motherboards or housed in boxes in very close proximity. Cosite interference and coupling in all electrical and electronic circuit assemblies are two essential issues that have to be examined in every design.

Balanis, Constantine A.↗

Laser angle sensor

A laser angle measurement system was designed and fabricated for NASA Langley Research Center. The instrument is a fringe counting interferometer that monitors the pitch attitude of a model in a wind tunnel. A laser source and detector are mounted above the model. Interference fringes are generated by a small passive element on the model. The fringe count is accumulated and displayed by a processor in the wind tunnel control room. This report includes optical and electrical schematics, system maintenance and operation procedures.

Pond, C. R.↗

Manufacturing and testing of a magnetically suspended composite flywheel energy storage system

This paper presents the work performed to develop a multiring composite material flywheel and improvements of a magnetically suspended energy storage system. The flywheel is constructed of filament would graphite/epoxy and is interference assembled for better stress distribution to obtain higher speeds. The stationary stack in the center of the disk supports the flywheel with two magnetic bearings and provides power transfer to the flywheel with a motor/generator. The system operates under a 10(exp -4) torr environment and has been demonstrated to 20,000 rpm with a total stored energy of 15.9 Wh. When this flywheel cycles between its design speeds (45,000 to 90,000 rpm), it will deliver 242 Wh and have a usable specific energy density of 42.6 Wh/kg.

Wells, Stephen↗

Shuttle orbiter S-band communications equipment design evaluation

An assessment of S-band communication equipment includes: (1) the review and analysis of the ability of the various subsystem avionic equipment designs to interface with, and operate on signals from/to adjoining equipment; (2) the performance peculiarities of the hardware against the overall specified system requirements; and (3) the evaluation of EMC EMI test results of the various equipment with respect to the possibility of mutual interferences.

Springett, J. C.↗