Search NASA⌕ Search

SEARCH · Search NASA

Results for “optical absorption spectroscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

The Gaussian nature of the band-edge of ZnO microcrystalline thin films

A straightforward analytical approach based on the derivative of the absorption coefficient is presented, which enables probing the nature of the band edge (BE) of ZnO microcrystalline films. The study was conducted via transmission experiments at temperatures of 77–532 K and repeated for samples annealed up to 1073 K. It was found that the derivative of the natural log of the BE absorption coefficient resulted in a Gaussian function. The Gaussian linewidth is used in the electron–phonon (e–p) interaction model to characterize the defect-state of the films. The BE of the as-grown film was found to exhibit no thermal dependence and no e–p coupling, indicative of a disordered crystal. Upon annealing and improvement of the film quality, the thermal phonons became more activated, but only above room temperature with a phonon energy of ~75 meV, while up to room temperature, the impact of phonons on the BE is insignificant. A disorder–order transition was determined to take place at an annealing temperature of ~673 K. X-ray diffraction concurs with these results. The study indicates that the prevalent defects are of structural nature due to the inherent granular morphology of the films. This defect was found to dominate the behavior of the BE even at the elevated temperature regime rather than thermal phonons.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Optimizing the sensitivity of high repetition rate broadband transient optical spectroscopy with modified shot-to-shot detection

A major limitation of transient optical spectroscopy is that relatively high laser fluences are required to enable broadband, multichannel detection with acceptable signal-to-noise levels. Under typical experimental conditions, many condensed phase and nanoscale materials exhibit fluence-dependent dynamics, including higher order effects such as carrier–carrier annihilation. With the proliferation of commercial laser systems, offering both high repetition rates and high pulse energies, have come new opportunities for high sensitivity pump-probe measurements at low pump fluences. However, experimental considerations needed to fully leverage the statistical advantage of these laser systems have not been fully described. Here, we demonstrate a high repetition rate, broadband transient spectrometer capable of multichannel shot-to-shot detection at 90 kHz. Importantly, we find that several high-speed cameras exhibit a time-domain fixed pattern noise resulting from interleaved analog-to-digital converters, which is particularly detrimental to the conventional “ON/OFF” modulation scheme used in pump-probe spectroscopy. Using a modified modulation and data processing scheme, we achieve a noise level of 10−5 in 4 s for differential transmission, an order of magnitude lower than for commercial 1 kHz transient spectrometers for the same acquisition time. We leverage the high sensitivity of this system to measure the differential transmission of monolayer graphene at low pump fluence. We show that signals on the order of 10−6 OD can be measured, enabling a new data acquisition regime for low-dimensional materials.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Ground state rotational and kinetic temperatures of C 2 molecules in a laser-produced plasma

This study presents an experimental comparison between rotational and kinetic temperatures of molecular species in a laser-produced plasma, utilizing tunable laser absorption spectroscopy. We analyzed high-resolution and time-resolved absorption spectra of 31 rotational transitions within the Phillips A 1 II u –X 1 Σ g 3-0 band of the C 2 molecule, measured from a laser-produced graphite plasma in ~2 Torr argon, within the 771–781 nm spectral range. Spectral fitting provided quantitative state column densities of C 2 rotational energy levels in the ground electronic and vibrational states. Boltzmann analysis revealed thermalized rotational distributions showing rotational temperatures decreasing from 3000 to 600 K within 5–500 μs following the onset of the laser plasma. The measured kinetic and rotational temperatures of C 2 molecules are comparable, suggesting that collisional processes in the laser-produced plasma are sufficient to maintain thermal equilibrium between the C 2 molecules and the Ar background gas.

Absorption spectroscopy↗
DOE OSTI2020

Lidar-based remote infrared gas sensor for monitoring anthropogenic pollution: a proof of concept

We propose using wavelength-modulation laser absorption spectroscopy in combination with quadrature detection of scattered light for remote industrial pollution monitoring in the atmosphere with a compact lidar-based gas sensor, which can be mounted on board an unmanned aerial vehicle. The instrument can be used for detecting leaks in product pipe lines; monitoring toxic gases near landfill sites, waste incineration plants, and other hazardous man-made facilities; analysing the gas atmosphere in industrial buildings and structures; and monitoring engineering processes at a sensitivity level of tens of ppm m in gas concentration measurements at characteristic distances of tens of metres. (laser applications and other issues in quantum electronics)

42 ENGINEERING↗
DOE OSTI2020

Extracting Optical Bandgaps from Luminescence Images of Perovskite Solar Cells

We report a camera-based method to capture optical bandgap images of perovskite solar cells (PSCs). It is fast and non-destructive. It can also provide micron-scale spatial resolution. This imaging technique utilizes well-defined and relatively symmetrical band-to-band luminescence spectra emitted from perovskite materials. Their spectra can be fitted with Gaussian functions whose peak locations are similar to absorption thresholds and thus represent the material optical bandgaps. We apply the technique to resolve relative variations in optical bandgaps across various PSCs, and to show optical bandgap inhomogeneity within the same device due to material degradation and impurities. Degradation and impurities were found to both cause optical bandgap shifts inside the materials. Our results are independently confirmed with photoluminescence and absorption spectroscopy.

14 SOLAR ENERGY↗
DOE OSTI2021

Local Structural Disorder in Metavanadates MV 2 O 6 (M = Zn and Cu) Synthesized by the Deep Eutectic Solvent Route: Photoactive Oxides with Oxygen Vacancies

Metavanadates MV 2 O 6–δ (M = Zn and Cu) are synthesized by using a deep eutectic solvent (DES), a mixture of hydrogen bond donor and acceptor, as a reaction medium. Dissolution of stable binary metal oxides in a DES followed by a heat treatment yields phase-pure vanadates. According to in situ powder X-ray diffraction, ternary phases (α-Zn 2 V 2 O 7 and β-Cu 2–x V 2 O 7 , x ~ 0.27) are intermediates in the reaction pathway taken. Identifying a polymorphic phase transformation temperature for CuV 2 O 6 as well as the narrow temperature range between formation and decomposition for both metavanadates allows for tackling the challenge of the synthesis of these materials. The oxygen vacancy introduced by the DES route is accompanied by the formation of reduced V 4+ and Cu + in the oxide matrix, based on X-ray photoelectron spectroscopy. These oxygen vacancies modify the vibrational modes in the corresponding Raman spectra and are also responsible for broad optical absorptions in the 1.8–1.1 eV range. The optical band gaps of the materials are found at 1.8 eV (CuV 2 O 6 ) and 2.2 eV (ZnV 2 O 6 ), approximately 0.1–0.3 eV below the values reported in the literature. The reduced band gaps and sub-band gap photon absorption are key features of the oxygen-deficient metavanadates. Surface photovoltage spectroscopy reveals that all the synthesized vanadates are n-type materials with electrons as the majority charge carriers, and photoelectrochemical measurements confirm photoanodic currents for methanol oxidation. Furthermore, these results provide insight into the synthesis and structure–property relationship of the metavanadates for their potential use as photoanodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Spectral Signatures of Ultrafast Excited-State Intramolecular Proton Transfer from Computational Multi-edge Transient X-ray Absorption Spectroscopy

Excited state intramolecular proton transfer (ESIPT) is a fundamental chemical process with several applications. Ultrafast ESIPT involves coupled electronic and atomic motions and has been primarily studied using femtosecond optical spectroscopy. X-ray spectroscopy is particularly useful because it is element-specic and enables direct, individual probes of the proton donating and accepting atoms. Here, we report a computational study to resolve the ESIPT in 10-Hydroxybenzo[h]quinoline (HBQ), an intramolecularly hydrogen bonded compound, using time-dependent density functional theory combined with ab initio molecular dynamics (AIMD) and time-resolved X-ray absorption spectroscopy (XAS) computations to track the ultrafast excited-state dynamics. Overall, our results reveal clear X-ray spectral signatures of coupled electronic and atomic motions during and following ESIPT at the oxygen and nitrogen K-edge paving the way for future experiments at X-ray free electron lasers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Carrier-specific dynamics in 2H-MoTe2 observed by femtosecond soft x-ray absorption spectroscopy using an x-ray free-electron laser

Femtosecond carrier dynamics in layered 2H-MoTe2 semiconductor crystals have been investigated using soft x-ray transient absorption spectroscopy at the x-ray free-electron laser (XFEL) of the Pohang Accelerator Laboratory. Following above-bandgap optical excitation of 2H-MoTe2, the photoexcited hole distribution is directly probed via short-lived transitions from the Te 3d5/2 core level (M5-edge, 572–577 eV) to transiently unoccupied states in the valence band. The optically excited electrons are separately probed via the reduced absorption probability at the Te M5-edge involving partially occupied states of the conduction band. A 400 ± 110 fs delay is observed between this transient electron signal near the conduction band minimum compared to higher-lying states within the conduction band, which we assign to hot electron relaxation. Additionally, the transient absorption signals below and above the Te M5 edge, assigned to photoexcited holes and electrons, respectively, are observed to decay concomitantly on a 1–2 ps timescale, which is interpreted as electron–hole recombination. The present work provides a benchmark for applications of XFELs for soft x-ray absorption studies of carrier-specific dynamics in semiconductors, and future opportunities enabled by this method are discussed.

2D materials↗
DOE OSTI2020

Anisotropic 2D excitons unveiled in organic-inorganic quantum wells

Here we report that two-dimensional (2D) excitons arise from electron-hole confinement along one spatial dimension. Such excitations are often described in terms of Frenkel or Wannier limits according to the degree of exciton spatial localization and the surrounding dielectric environment. In hybrid material systems, such as the 2D perovskites, the complex underlying interactions lead to excitons of an intermediate nature, whose description lies somewhere between the two limits, and a better physical description is needed. Here, we explore the photophysics of a tuneable materials platform where covalently bonded metal-chalcogenide layers are spaced by organic ligands that provide confinement barriers for charge carriers in the inorganic layer. We consider self-assembled, layered bulk silver benzeneselenolate, [AgSePh] ∞ , and use a combination of transient absorption spectroscopy and ab initio GW plus Bethe-Salpeter equation calculations. We demonstrate that in this non-polar dielectric environment, strongly anisotropic excitons dominate the optical transitions of [AgSePh] ∞ . We find that the transient absorption measurements at room temperature can be understood in terms of low-lying excitons confined to the AgSe planes with in-plane anisotropy, featuring anisotropic absorption and emission. Finally, we present a pathway to control the exciton behaviour by changing the chalcogen in the material lattice. Our studies unveil unexpected excitonic anisotropies in an unexplored class of tuneable, yet air-stable, hybrid quantum wells, offering design principles for the engineering of an ordered, yet complex dielectric environment and its effect on the excitonic phenomena in such emerging materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Detection limits for laser absorption spectroscopy of Li in laser ablation plumes

A high-sensitivity laser absorption spectroscopy (LAS) method is demonstrated for rapid and non-contact analysis of Li in solids. Glass samples with Li concentrations ranging from 1-500 ppm by mass are ablated in 5 Torr air, and time-resolved Li atomic absorption is measured using a tunable laser near 671 nm. Significant improvements in analytical performance over prior laser-induced breakdown techniques are demonstrated. Here, a single-shot limit of detection (LOD) of 180 ppb is shown for fixed wavelength operation, improving to 6 ppb with averaging over 1000 ablation shots (100 s acquisition time). Isotope-resolved Li absorption spectra are measured with a 17 ppb LOD in 40 s. Methods for optimizing LOD based on noise/averaging properties of LAS experiments in LA plumes are discussed.

(020.3260) Isotope shifts↗
DOE OSTI2022

Inferring relative dose-dependent color center populations in proton irradiated thoria single crystals using optical spectroscopy

In this work, we have utilized photoluminescence spectroscopy and optical ellipsometry to characterize the dose-dependence of the photoluminescence emission intensity and changes in optical absorption of thoria single crystals subject to irradiation with energetic protons at room- and elevated-temperatures. The photoluminescence peaks and the optical absorption bands are attributed to creation of new electronic states emerging from defects resulting from displacement damage. These bands are most likely associated with electrons trapped at the oxygen vacancy sites similar to color centers formed in other irradiated oxides and halides. Our experimental observations are supported by a standard density functional theory calculation of the electronic structure in pristine and oxygen vacancy-bearing thoria crystals. The dose-dependence of the intensity of the photoluminescence peaks is used to parameterize a rate theory model that estimates the concentration of color centers in the irradiated crystals. This parameterization provides optimized migration barrier parameters for oxygen interstitials and vacancies that simultaneously capture the optical response of the crystals irradiated at room- and elevated-temperature. These optical spectroscopy techniques offer a promising pathway to characterize the population of color centers formed at the sites of oxygen anion vacancies, particularly in irradiated nuclear fuels, where atomic-level defects cannot be readily imaged using electron microscopy. When combined with other direct and indirect characterization tools, our approach can provide new insight into defect formation and accumulation in energy materials over single atomic to extended length scales.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Feasibility of using distributed chemical sensing for CO2 leakage monitoring

The feasibility study focused on the development of new fiber for distributed chemical sensing (DCS) that will allow direct detection of CO 2 leakages in the environment. This is particularly important for monitoring well integrity for carbon capture and storage (CCS), to provide early warning for an incoming well failure and potential CO 2 leaking through it. We proposed using optical spectroscopy in optical fiber for direct detection of CO 2 . The main approach is based on Raman interrogation within gas-filled Holey Fibers (HoFs), so that the location and concentration of the gases would be provided simultaneously via backscattering. Additionally, Infrared (IR) Absorption Spectroscopy could also be used, and the architecture would be more discrete since interleaving with standard solid core fibers and Fiber Bragg Grating (FBG) sections is required to enable reflection to the I/O controls. The possible Raman length or the IR numbers of sections would be defined based on signal to noise ratio. The optical spectroscopy methodology would overcome current roadblocks to CCS, as fiber optics will allow for CO 2 (and other gases) detection in wells with direct in-situ measurements of concentration along with other important parameters such as temperature and pressure as the baseline of environment background.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2019

Infrared absorption cross section of SiN x thin films

At the molecular level, resonant coupling of infrared radiation with oscillations of the electric dipole moment determines the absorption cross section, $σ$. The parameter σ relates the bond density to the total integrated absorption. In this work, $σ$ was measured for the Si–N asymmetric stretch mode in SiN x thin films of varying composition and thickness. Thin films were deposited by low pressure chemical vapor deposition at 850 °C from mixtures of dichlorosilane and ammonia. σ for each film was determined from Fourier transform infrared spectroscopy and ellipsometric measurements. Increasing the silicon content from 0% to 25% volume fraction amorphous silicon led to increased optical absorption and a corresponding systematic increase in σ from 4.77 × 10 –20 to 6.95 × 10 –20 cm 2 , which is consistent with literature values. The authors believe that this trend is related to charge transfer induced structural changes in the basal SiN x tetrahedron as the volume fraction of amorphous silicon increases. Furthermore, experimental $σ$ values were used to calculate the effective dipole oscillating charge, q, for four films of varying composition. The authors find that q increases with increasing amorphous silicon content, indicating that compositional factors contribute to modulation of the Si–N dipole moment. Additionally, in the composition range investigated, the authors found that $σ$ agrees favorably with trends observed in films deposited by plasma enhanced chemical vapor deposition.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Americium Oxalate: An Experimental and Computational Investigation of Metal–Ligand Bonding

A novel actinide-containing coordination polymer, [Am(C 2 O 4 )(H 2 O) 3 Cl] (Am-1), has been synthesized and structurally characterized. The crystallographic analysis reveals that the structure is two-dimensional and comprised of pseudo-dimeric Am 3+ nodes that are bridged by oxalate ligands to form sheets. Each metal center is nine-coordinate, forming a distorted capped square antiprism geometry with a C 1 symmetry, and features bound oxalate, aqua, and chloro ligands. The Am 3+ –ligand bonds were probed computationally using the quantum theory of atoms in molecules nd natural localized molecular orbital approaches to investigate the underlying mechanisms and hybrid atomic orbital contributions therein. The analyses indicate that the bonds within Am-1 are predominantly ionic and the 5f shell of the Am 3+ metal centers does not add a significant covalent contribution to the bonds. Further, our bonding assessment is supported by measurements on the optical properties of Am-1 using diffuse reflectance and photoluminescence spectroscopies. The position of the principal absorption band at 507 nm ( 5 L 6' ← 7 F 0' ) is notable because it is consistent with previously reported americium oxalate complexes in solution, indicating similarities in the electronic structure and ionic bonding. Compound Am-1 is an active phosphor, featuring strong bright-blue oxalate-based luminescence with no evidence of metal-centered emission.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Electronic and optical properties of Zn-doped β-Ga 2 O 3 Czochralski single crystals

β-Ga 2 O 3 has several soluble deep acceptors that impart insulating behavior. In this study, we investigate Zn doping (0.25at.%) in bulk Czochralski and vertical gradient freeze β-Ga 2 O 3 . Representative crystals were assessed for orientation (electron backscatter diffraction and Raman spectroscopy), purity (glow discharge mass spectrometry and secondary ion mass spectrometry), optical properties (ultraviolet to near infrared absorption), and electrical properties (resistivity and current–voltage). Purity measurements indicate that Zn evaporation is insufficient to inhibit doping of Zn into β-Ga 2 O 3 . Hybrid functional calculations show Zn substitutes nearly equally on tetrahedral and octahedral sites, with less than ~0.1eV preference for the octahedral (Ga II ) site. Furthermore, calculations show that Zn Ga acts as a deep acceptor with trapping levels ~1.3 and ~0.9eV above the valence band for one and two holes, respectively. The solubility and electronic behavior of Zn dopants are consistent with measured concentrations >1×10 18 atoms/cm 3 and electrical measurements that show resistivity 10 11 –10 13 Ωcm, with no p-type conduction.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Local electric field measurement in GaN diodes by exciton Franz–Keldysh photocurrent spectroscopy

The eXciton Franz–Keldysh (XFK) effect is observed in GaN p–n junction diodes via the spectral variation of photocurrent responsivity data that redshift and broaden with increasing reverse bias. Photocurrent spectra are quantitatively fit over a broad photon energy range to an XFK model using only a single fit parameter that determines the line shape and the local bias (V l ), uniquely determining the local electric field maximum and depletion widths. As expected, the spectrally determined values of V l vary linearly with the applied bias (V) and reveal a large reduction in the local electric field due to electrostatic non-uniformity. The built-in bias (V bi ) is estimated by extrapolating V l at V=0, which, when compared with independent C-V measurements, indicates an overall ±0.31 V accuracy of V l . This demonstrates sub-bandgap photocurrent spectroscopy as a local probe of electric field in wide bandgap diodes that can be used to map out regions of device breakdown (hot spots) for improving electrostatic design of high-voltage devices.

42 ENGINEERING↗
DOE OSTI2020

Non-Hermitian approach for quantum plasmonics

Herein, we examine the limits of applicability of a simple non-Hermitian model for exciton/plasmon interactions in the presence of dissipation and dephasing. The model can be used as an alternative to the more complete Lindblad density matrix approach and is computationally and conceptually simpler. We find that optical spectra in the linear regime can be adequately described by this approach. The model can fail, however, under continuous optical driving in some circumstances. In the case of two quantum dots or excitons interacting with a plasmon, the model can also describe coherences and entanglement qualitatively when both dissipation and dephasing are present and quantitatively in the limit with no dephasing. The approach, within a single excitation manifold, is also applied to assess the role of disorder for 50 quantum dots interacting with a plasmon, where we find that, on average, large enough disorder can help stabilize the ensemble average of the open quantum system toward a dark quasi-steady-state much faster than without disorder. Furthermore, while such single excitation manifold calculations in this size limit can readily be done with either the non-Hermitian or Lindblad forms, as one goes to larger Hilbert space sizes, the computational and storage advantages of the non-Hermitian approach can become more useful. Published under license by AIP Publishing.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗