Search NASA⌕ Search

SEARCH · Search NASA

Results for “particle distributions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Solvent-Free Melt-Processed Cathode Mitigates Li Anode Instability in Polymer-Based Solid-State Batteries

Solvent-free manufacturing of battery components is a promising alternative to traditional slurry processing for reducing the cost and environmental impact. In this work, we used twin-screw melt extrusion to fabricate a polymer-based high voltage composite cathode. The melt-processed cathode is dense (near zero porosity) and thick (65 μm) and has high active material loading (80 wt %). The active particles are distributed uniformly throughout the melt-processed cathode, unlike the traditional slurry-cast cathode, which exhibits inhomogeneous particle distribution. In the melt-processed cathode, polymer and carbon form separate phases, whereas in the slurry-cast cathode they blend into a single phase. Due to these structural differences, the melt-processed cathode shows smooth charge–discharge profiles, while the slurry-cast cathode shows noisy charging and soft-shorting behavior. In conclusion, this work highlights that twin-screw extrusion as a scalable, solvent-free manufacturing method is advantageous in producing uniform cathodes, which mitigates anode instability.

25 ENERGY STORAGE↗
DOE OSTI2021

Experimental investigation of the effect of pore size distribution on nano-particle capture efficiency within ceramic particulate filters

The effect of the pore size distribution on size-resolved filtration efficiency was investigated for two ceramic particulate filters using particulate matter (PM) generated by a spark-ignition direct-injection engine fueled with gasoline. The cordierite filter tested had a porosity of 43%, a median pore diameter (d_50) of 12 µm, and a wide pore size distribution with a lognormal standard deviation (s’) of 0.3. The aluminum titanate filter had very similar porosity, d_50, and thickness, but significantly narrower pore size distribution (s’ = 0.1). The testing of two filters under identical experimental conditions enabled the impact of the pore size distribution on filtration performance to be evaluated. Filtration experiments were performed focusing on just the filter wall, starting from a clean filter until the transition to cake filtration (filtration efficiency > 99%). Time-resolved particle size distribution measurements were used to evaluate the progression of filtration performance and estimate trapped mass within the filter. The aluminum titanate filter, with a narrow pore size distribution, exhibited significantly better diffusion capture efficiency. The negative impact of higher flow velocity on diffusion capture efficiency was more pronounced for a narrower pore size distribution. Flow distributions measured using capillary-flow porometry were used to develop a cylindrical pore flow model to understand the impact of the differences in pore size distribution on observed trends in diffusion capture efficiency within a clean filter. The model helps demonstrate how large pores on the high end of a wider pore size distribution can carry a large fraction of the flow, with less efficient capture of small particles by diffusion. The experimental results and data demonstrate that the bubble point diameter and width of the pore size distribution significantly influence diffusion capture efficiencies for filters with very similar median pore diameter, porosity, and thickness.

aerosol filtration, Aftertreatment, ceramic exhaus↗
DOE OSTI2022

mergedsmpsaps

Merged aerosol particle size distributions for the Aerodynamic Particle Sizer (APS) and Scanning Mobility Particle Sizer (SMPS) instruments

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Accurate models of the added mass force of a uniform random distribution of spherical particles or bubbles

The added mass force resulting from the acceleration of a body in a fluid is of fundamental and practical interest in dispersed multiphase flows. Euler–Lagrange (EL) and Euler–Euler (EE) simulations require closure terms for the added mass force in order to accurately couple the conserved variables between phases. Presently, a more thorough understanding of the added mass force in a multi-particle system is developed based on potential flow resulting in a resistance matrix formulation analogous to Stokesian dynamics. This formulation is then used to generate a dataset of added mass resistance matrices for large systems of randomly generated particles. This methodology is used to create a volume fraction corrected binary model for predicting the added mass force in large systems as well as generate statistics of the added mass force in such systems. This work provides clarification to the theory of the added mass force for particle clouds, and modelling options that may be implemented in existing EL and EE codes.

42 ENGINEERING↗
DOE OSTI2025

Resonance-stabilized radical clustering bridges the gap between gaseous precursors and soot in the inception stage

Carbonaceous particles are widespread in combustion, atmospheric, extraterrestrial, and nanomaterials environments. Resonance-stabilized radicals (RSRs) are commonly identified in fuel combustion and pyrolysis processes and play an essential role in carbonaceous particle formation. Despite their importance, comprehensive experimental and mechanistic understanding of particle inception through RSR reactions is lacking. This work investigated particle size distribution, chemical composition, and thermal behavior of soot particles generated by the flow reactor pyrolysis reactions of typical RSRs, in particular, 1-indenyl, 1-methylnaphthyl, and 2-methylnaphthyl radicals, and by the pyrolysis of hydrocarbons with a variety of structures. Particle size distributions show soot particles with mobility diameters in an incipient-particle range of 1.3 to 1.6 nm. Laser desorption/ionization mass spectrometry results suggest that soot products consist of much larger covalently bound clusters (CBCs) than those observed in the gas phase. Under our experimental conditions, the CBCs exhibit a phase transition for particles with calculated molecular diameters of around 1.5 nm. Evaporation experiments and thermogravimetric analysis of the soot products reveal distinct thermal characteristics for small and large CBCs. These results implicate CBCs as bridges between gas-phase species and soot particles. The present work provides a soot-inception mechanism called RSR clustering (RSRC) that is characterized by the reactive clustering of RSRs. The RSRC mechanism contrasts with conventional soot formation models that attribute soot inception primarily to the aggregation of large-size polycyclic aromatic hydrocarbons.

carbonaceous particle↗
DOE OSTI2021

Pseudorapidity distributions of charged particles as a function of mid- and forward rapidity multiplicities in pp collisions at $\sqrt{s}$ = 5.02, 7 and 13 TeV

The multiplicity dependence of the pseudorapidity density of charged particles in proton–proton (pp) collisions at centre-of-mass energies √s = 5.02, 7 and 13 TeV measured by ALICE is reported. The analysis relies on track segments measured in the midrapidity range (|η| < 1.5). Results are presented for inelastic events having at least one charged particle produced in the pseudorapidity interval |η| < 1. The multiplicity dependence of the pseudorapidity density of charged particles is measured with mid- and forward rapidity multiplicity estimators, the latter being less affected by autocorrelations. A detailed comparison with predictions from the PYTHIA 8 and EPOS LHC event generators is also presented. The results can be used to constrain models for particle production as a function of multiplicity in pp collisions.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Let’s Stick Together: Interplay of Moisture, Particle Size, and Anatomical Fraction in the Flowability of Corn Stover Crumbles

Handling of agricultural waste biomass feedstocks (such as corn stover) is a persistent challenge in the production of biofuels and chemicals at integrated biorefineries. Inconsistent flowability and high feedstock variability creates equipment downtime and processing challenges. This work investigates the influence of anatomical fractionation and moisture content on the bulk solids handling behavior of corn stover crumbles. A combination of rotational shear testing, tribological measurements, and surface and sorption characterization techniques (inverse gas chromatography (IGC), dynamic vapor sorption (DVS), and electron microscopy) were used to evaluate the contributions of particle composition, size, and surface properties to flow behavior. Shear and frictional testing revealed that moisture content has the greatest effect on flowability, significantly increasing unconfined yield strength (ƒ c ) and reducing the flow function coefficient (F F C), regardless of anatomical fraction. While differences in surface energy were observed between fractions, particularly in polar contributions (γ AB ), these did not correspond to meaningful differences in flow behavior. Coarser 6 mm particles exhibited poorer flow performance than 4 mm crumbles, likely due to broader particle size distributions and increased particle interlocking. Taken together, these results suggest that anatomical fractionation provides minimal benefit from a bulk handling perspective. Moisture content and particle size heterogeneity dominate handling behavior, reinforcing the utility of unfractionated corn stover in processing environments. These insights can inform the design of more efficient and reliable feedstock processing systems for agricultural biomass in integrated biorefineries.

09 BIOMASS FUELS↗
DOE OSTI2026

Particle Tracking Methods for Battery Precipitation Reactions

Precipitation and deposition reactions at solid–liquid interfaces play a key role in a number of battery chemistries, including Li-ion, so-called “anode free” batteries, zinc-based battery chemistries, and lithium–sulfur, among others. Although models with heterogeneous nucleation and growth phenomena are present in the literature, papers have not to date provided much detail on the numerical algorithms used to track the temporal evolution of the particle size distribution of deposits on electrode surfaces. In this paper we examine several approaches to discretize and track the particle size distribution, demonstrating that common approaches lead to anomalous flattening of the particle size distribution. We conclude by presenting an algorithm that preserves the appropriate particle size distribution during particle growth.

Algorithms↗
DOE OSTI2023

Experimental study on particle formation in a pressurized oxy-fuel combustor using a novel in-situ optical instrument

Particle formation in pressurized oxy-fuel combustion can be fundamentally different from oxy-fuel combustion at atmospheric pressure. Under high pressures, the rate of char gasification with CO2 and H2O increases significantly and dominates the char reactions particularly at high temperatures. Also, the extent of fragmentation varies. This could result in a very different particle size distribution from that of air-fired combustion. To accurately obtain the particle size distribution in a pressurized oxy-fuel combustor without sampling bias, the particle measurement should be made at the system pressure. Very few published studies have accomplished this, and never under the conditions reported herein. In this work, we fire PRB coal in a 100 kWth staged pressurized oxy-fuel combustor (SPOC) under two pressures, 15 and 2 bara. A sampling probe (oil-cooled) is installed at the combustor outlet and the aerosol flow are sampled isokinetically. We utilize a state-of-the-art optical analyzer (Malvern Insitec) with a novel high-pressure and high-temperature flow cell to measure the particle size distribution and concentration in-situ in a sampled flow, which contains moist/corrosive flue gas under the process pressure and a controlled temperature that is kept above the dew point. The results show that the pressure can significantly influence the particle size distribution and concentration from the oxy-fuel combustor.

Cheng, Mao↗
DOE OSTI2026

High Time Resolution Modelled and Measured New Particle Formation Rates During the 2023 Pittsburgh, PA Campaign

Particle size distributions are used to calculate nucleation rates during new particle formation (NPF). However, the low time resolution and poor sensitivity of instruments deployed to observe particle size distributions can lead to inaccurate estimates of nucleation rates. We calculated nucleation rates in Pittsburgh, PA from particle size distributions measured with the new high time resolution Condensation Particle Counters For Atmospheric Rapid Measurements (CPC FARM) and from gas precursor concentrations measured with a chemical ionization mass spectrometer. The CPC FARM nucleation rates were calculated by examining the appearance rate of particles in the smallest size bin at 1.6 nm. The nucleation rate of 1.6 nm determined every second resulted in positive and negative rates, indicating the influence of inhomogeneous mixing and advection of precursor gases and clusters. These effects are not currently considered when estimating nucleation rates from measurements. The nucleation rates from the CPC FARM were compared to the nucleation rates determined from a transient acid‐base reaction model using measured sulfuric acid concentration, strong base concentrations, and CPC detection efficiencies. The transient form of the model allowed the advection of heterogeneously mixed precursors to influence the nucleation rate. Good agreement between particle and gas‐based nucleation rates is observed during sulfuric acid‐driven NPF events. This study demonstrates that high time resolution measurements of short‐lived and rapidly formed particles are needed to accurately capture nucleation rates, which are likely influenced by advection of nucleation precursors and clusters in heterogeneous environments such as urban areas.

Cheng, D. [Carnegie Mellon Univ., Pittsburgh, PA (↗
DOE OSTI2023

Muon Decay Study at NSRL

A muon is an unstable subatomic particle, classified as a lepton according to the Standard Model. Muons are charged leptons with 1/2 spin. They were discovered by Neddermeyer and Anderson from hadronic cosmic ray showers. Figure 1 provides a visual representation of a cosmic ray shower in Earth’s atmosphere. At a height of 50 000 m in the atmosphere, a primary cosmic ray (mainly protons, helium, a heavy nucleus or a gamma ray) interacts with a gas molecule. The striking of a gas molecule creates a cosmic ray shower, where the energy of the primary particle is distributed among many secondary particles and gamma rays. With each interaction, the cosmic ray particles in the shower lose energy but distribute this energy among a higher number of particles. From the initial interaction, primarily heavy nuclei and pions are generated. Heavy nuclei will interact with gas molecules to produce protons, gamma rays, electrons and pions. The dominant decay mode of neutral pions is to two gamma rays, while charged pions decay to a muon and a neutrino (equation 1): $π^+ → µ^+$ + $\overline ν$ $_µ$; $π → µ$ $^-$ + $\overline v$ $_µ$.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Characterization of the Emissions and Crystalline Silica Content of Airborne Dust Generated from Grinding Natural and Engineered Stones

Abstract In this study, we systematically characterized the airborne dust generated from grinding engineered and natural stone products using a laboratory testing system designed and operated to collect representative respirable dust samples. Four stone samples tested included two engineered stones consisting of crystalline silica in a polyester resin matrix (formulations differed with Stones A having up to 90wt% crystalline silica and Stone B up to 50wt% crystalline silica), an engineered stone consisting of recycled glass in a cement matrix (Stone C), and a granite. Aerosol samples were collected by respirable dust samplers, total dust samplers, and a Micro-Orifice Uniform Deposit Impactor. Aerosol samples were analyzed by gravimetric analysis and x-ray diffraction to determine dust generation rates, crystalline silica generation rates, and crystalline silica content. Additionally, bulk dust settled on the floor of the testing system was analyzed for crystalline silica content. Real-time particle size distributions were measured using an Aerodynamic Particle Sizer. All stone types generated similar trimodal lognormal number-weighted particle size distributions during grinding with the most prominent mode at an aerodynamic diameter of about 2.0-2.3 μm, suggesting dust formation from grinding different stones is similar. Bulk dust from Stone C contained no crystalline silica. Bulk dust from Stone A, Stone B, and granite contained 60, 23, and 30wt% crystalline silica, respectively. In Stones A and B, the cristobalite form of crystalline silica was more plentiful than the quartz form. Only the quartz form was detected in granite. The bulk dust, respirable dust, and total dust for each stone had comparable amounts of crystalline silica, suggesting that crystalline silica content in the bulk dust could be representative of that in respirable dust generated during grinding. Granite generated more dust per unit volume of material removed than the engineered stones, which all had similar normalized dust generation rates. Stone A had the highest normalized generation rates of crystalline silica, followed by granite, Stone B, and Stone C (no crystalline silica), which likely leads to the same trend of respirable crystalline silica (RCS) exposure when working with these different stones. Manufacturing and adoption of engineered stone products with formulations such as Stone B or Stone C could potentially lower or eliminate RCS exposure risks. Combining all the effects of dust generation rate, size-dependent silica content, and respirable fraction, the highest normalized generation rate of RCS consistently occurs at 3.2-5.6 µm for all the stones containing crystalline silica. Therefore, removing particles in this size range near the generation sources should be prioritized when developing engineering control measures.

Public, Environmental & Occupational Health↗
DOE OSTI2023

mergedsmpsapsml

Merged aerosol particle size distributions for the Aerodynamic Particle Sizer (APS) and Scanning Mobility Particle Sizer (SMPS) instruments with Machine Learning Quality Checks Applied

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Integrated modeling methodology for ash agglomeration in poly-disperse fluidized beds using particle population framework

This article discusses a unique agglomeration modeling methodology developed based on binary collisions to combine the effects of heterogeneity in ash chemistry and granular physics. A simple population balance is defined to find changes in the particle size distribution (PSD) of a fluidized bed. Thermodynamic equilibrium calculations and a computational fluid dynamics (CFD) code, are used to obtain hydrodynamic parameters. A method to calculate and use a distribution of collision frequencies in fluidized beds, corresponding to a poly-disperse particle size distribution, was developed in order to incorporate the particle level heterogeneities. A distribution of collision frequencies obtained for poly-dispersed particles showed a three orders of magnitude higher collision frequency amongst the smaller particles than the coarser ones, at the initiation of agglomeration. Ash agglomeration occurred when the slag amount (binder) was less than 10 wt% at temperatures <850 °C for Pittsburgh No. 8 coal.

42 ENGINEERING↗
DOE OSTI2020

Predicting Emission Source Terms in a Reduced-Order Fire Spread Model—Part 1: Particulate Emissions

A simple, easy-to-evaluate, surrogate model was developed for predicting the particle emission source term in wildfire simulations. In creating this model, we conceptualized wildfire as a series of flamelets, and using this concept of flamelets, we developed a one-dimensional model to represent the structure of these flamelets which then could be used to simulate the evolution of a single flamelet. A previously developed soot model was executed within this flamelet simulation which could produce a particle size distribution. Executing this flamelet simulation 1200 times with varying conditions created a data set of emitted particle size distributions to which simple rational equations could be tuned to predict a particle emission factor, mean particle size, and standard deviation of particle sizes. These surrogate models (the rational equation) were implemented into a reduced-order fire spread model, QUIC-Fire. Using QUIC-Fire, an ensemble of simulations were executed for grassland fires, southeast U.S. conifer forests, and western mountain conifer forests. Resulting emission factors from this ensemble were compared against field data for these fire classes with promising results. Also shown is a predicted averaged resulting particle size distribution with the bulk of particles produced to be on the order of 1 μm in size.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Optical filters made from random metasurfaces using Bayesian optimization

Abstract We theoretically investigate the ability to design optical filters from a single material and a single layer of randomly dispersed resonant dielectric particles, defining a random metasurface. Using a Bayesian and generalized Mie inverse-design approach, we design particle radii distributions that give rise to longpass, shortpass, bandpass, and bandstop spectral bands in the infrared. The optical response is shown to be directly related to electric and magnetic multipole scattering of the constituent particles and their near field coupling. We discuss the effect of the particle size distribution and particle–particle coupling interactions on filter design in random systems lacking long-range order.

Materials Science↗
DOE OSTI2021

Reducing Zinc Redistribution and Extending Cycle Life Via Electrochemical Synthesis of Zinc/Zinc Oxide Anodes in Rechargeable Alkaline Batteries

Redistribution of zinc over the electrode surface, also known as shape change, is a major problem and a cause of failure in alkaline zinc anode batteries. To mitigate this phenomenon, we propose a scalable approach based on an in situ formed, highly porous electrochemically synthesized ZnO matrix with uniformly electrodeposited zinc particles. This results in ∼70% improvement in cycle life performance at a rate of 10 mA cm −2 compared to control Zn anodes, which have not gone through the formation process. A quantitative electrolyte analysis revealed under-saturated zincate ion concentration in the electrochemically synthesized ZnO/Zn cells indicating reduced zincate movement. Post mortem analysis of the anodes indicated higher retention of both Zn and ZnO on the electrochemically synthesized ZnO anodes signifying reduced redistribution of active material. Image analysis of the cycled anodes revealed a narrower Zn particle size distribution (62−79 μ m) in contrast to a wider particle size distribution of 51–96 μ m observed in the control anodes. The formation approach results in electrochemically synthesized ZnO/Zn anodes providing a stable ZnO matrix in which Zn particles retain their localized distribution on cycling better than control electrodes conventionally made by pasting zinc particles together with a binder.

Kolhekar, Snehal (ORCID:0000000210321153)↗