SEARCH · Search NASA

Results for “particle fracture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS1992

The Martian ocean: First acid, then alkaline

In Mars' distant past, carbon dioxide and water may have been plentiful. Values of total outgassed CO2 from several to about 10 bar are consistent with present knowledge, and this amount of CO2 implies an amount of water outgassed equal to an equivalent depth of 500 to 1000 m. It is quite reasonable, therefore, to envision an early Mars in which there was a body or bodies of liquid water, perhaps in the northern plains, and a dense carbon dioxide atmosphere. Under such conditions, the pH of the water will be low, due to the dissolution of carbon dioxide in the water to form carbonic acid. This acidic water is capable of weathering the available rock quite intensely, particularly because this rock is likely to be heavily fractured (from meteorite bombardment) or even consist of fine particles (such as pyroclastic deposits). As time goes on, however, the carbon dioxide atmosphere will rapidly pass through the ocean to form carbonate deposits. As the density of the atmosphere decreases, so will the flux of carbonic acid into the ocean. Without this input of carbonic acid, the effect of the dissolved weathering products will be to increase the pH of the water. The ocean will then become alkaline. To study this process, I have developed a geochemical cycle model for the atmosphere-hydrosphere-regolith system of Mars. The treatment of geochemical cycles as complex kinetic chemical reactions has been undertaken for terrestrial systems in recent years with much success. This method is capable of elegantly handling the interactions between the simultaneous chemical reactions needed to understand such a system.

Schaefer, M. W.↗

NASA NTRS1960

Criteria for Yielding of Dispersion-Strengthened Alloys

A dislocation model is presented in order to account for the yield behavior of alloys with a finely dispersed second-phase. The criteria for yielding used in the model, is that appreciable yielding occurs in these alloys when the shear stress due to piled-up groups of dislocations is sufficient to fracture or plastically deform the dispersed second-phase particles, relieving the back stress on the dislocation sources. Equations derived on the basis of this model, predict that the yield stress of the alloys varies as the reciprocal square root of the mean free path between dispersed particles. Experimental data is presented for several SAP-Type alloys, precipitation-hardened alloys and steels which are in good agreement with the yield strength variation as a function of dispersion spacing predicted by this theoretical treatment.

Ansell, G. S.↗

NASA NTRS2016

Cementation and Aqueous Alteration of a Sandstone Unit Under Acidic Conditions in Gale Crater, Mars

The Curiosity rover landed on Mars in August 2012 to explore the sedimentary history and to assess the habitability of Gale Crater. After 1200 sols of surface operations and over 12 km of traverse distance, the mineralogy of 10 samples has been determined by the CheMin X-ray diffractometer (XRD) and the chemical composition of nearly 300 targets has been established by the Alpha Particle X-ray Spectrometer (APXS). Light-toned fracture zones containing elevated concentrations of silica have been studied by Curiosity's instruments to determine the nature of the fluids that resulted in the enrichment of SiO2. Multiple fluid exposures are evident, and the chemistry and mineralogy data indicate at least two aqueous episodes may have occurred under acidic conditions.

Yen, A. S.↗

DOE OSTI2023

Develop and Connect TRISO Failure Analysis and Uncertainty Quantification to Fission Product Release Calculation Capability

The U.S. Department of Energy’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aims to develop predictive capabilities by applying computational methods to the analysis and design of advanced reactor and fuel cycle systems. This program has been providing engineering-scale support for the development of BISON, a high-fidelity and high-resolution fuel performance tool. Stress-based failure probability has been developed and analyzed to assess the integrity of tri-structural isotropic (TRISO) fuel particles during fuel life cycles. While simple, stress-based approaches to failure probability leveraging the Weibull statistical distribution entails a number of drawbacks when stress concentration occurs near crack tips, including finite element mesh size dependency. In this report, we use an interaction integral approach to the computation of stress intensity factors in functionally graded materials (FGM) for axisymmetric models. The inner pyrolytic carbon (IPyC) cracking induced silicon carbide (SiC) failure is one of the dominated failure modes in TRISO failure analysis. In this study, we consider a crack in the IPyC layer perpendicular to the SiC layer. The interface between these two TRISO layers is considered to be porous, which we simulate considering a transition of mechanical properties over the porous length. These aspects are considered in the computation of stress intensity factor (SIF) from a fracture mechanics approach and compared with the known stress-based failure probability approach.

42 ENGINEERING↗

NASA NTRS1983

A surface analytical examination of Stringer particles in Al-Li-Cu alloys

A surface analytical examination of powder metallurgy processed Al-Li-Cu alloys was conducted. The oxide stringer particles often found in these alloys was characterized. Particle characterization is important to more fully understand their impact on the stress corrosion and fracture properties of the alloy. The techniques used were SIMS (Secondary Ion Mass Spectroscopy) and SAM (Scanning Auger Microscopy). The results indicate that the oxide stringer particles contain both Al and Li with relatively high Li content and the Li compounds may be associated with the stringer particles, thereby locally depleting the adjacent matrix of Li solute.

Larson, L. A.↗

NASA NTRS1984

A surface-analytical examination of stringer particles in aluminum-lithium-copper alloys

A surface analytical examination of powder metallurgy processed Al-Li-Cu alloys was conducted. The oxide stringer particles often found in these alloys are characterized. Particle characterization is important to more fully understand their impact on the stress corrosion and fracture properties of the alloy. The techniques used where SIMS (Secondary Ion Mass Spectroscopy) and SAM (Scanning Auger Microscopy). The results indicate that the oxide stringer particles contain both Al and LI with relatively high Li content and the Li compounds may be associated with the stringer particles, thereby locally depleting the adjacent matrix of Li solute.

Larson, L. A.↗

NASA NTRS2009

Dynamic Mechanical Properties and Fracture Surface Morphologies of Core-Shell Rubber (CSR) Toughened Epoxy at Liquid Nitrogen (Ln2) Temperatures

The dynamic mechanical properties and fracture surface morphologies were evaluated for a commercial epoxy resin toughened with two types of core-shell rubber (CSR) toughening agents (Kane Ace(Registered TradeMark) MX130 and MX960). The impact resistance (R) was evaluated by the resulting breaking energy measured in Charpy impact tests conducted on an instrumented drop tower. The resulting fracture surface morphologies were examined using Scanning Electron Microscopy (SEM). Fractographic observations of the CSR toughened epoxy tested at ambient temperature, showed a fracture as characterized by slender dendrite textures with large voids. The increasing number of dendrites and decreasing size of scale-like texture with more CSR particles corresponded with increased R. As the temperature decreased to Liquid Nitrogen (LN 2), the fracture surfaces showed a fracture characterized by a rough, torn texture containing many river markings and deep furrows.

Wang, J.↗

NASA NTRS1977

Metallurgical characterization of the fracture of several high strength aluminum alloys

The fracture behavior for structural aluminum alloys (2024, 6061, 7075, and 7178) was examined in selected heat treatments. The investigation included tensile, shear, and precracked notch-bend specimens fractured at ambient temperature under monotonic loading. Specimens were obtained from thin sheets and thick plates and were tested in longitudinal and transverse orientations at different strain rates. Microstructures of alloys were examined using the optical microscope and the scanning electron microscope with associated energy dispersive X ray chemical analysis. Several different types of second phase particles, some not reported by other investigators, were identified in the alloys. Fracture morphology was related to microstructural variables, test variables, and type of commercial product. Specimen orientation examined in the present investigation had little effect on fracture morphology. Test strain rate changes resulted in some change in shear fracture morphology, but not in fracture morphology of tensile specimens.

Bhandarkar, M. D.↗

DOE OSTI2025

Numerical simulation of asteroid geometry variance on airburst threat

For an atmospheric airburst the primary source of concern when assessing uncertainty is the size and velocity. Determining these properties provides the basis for threat assessment, as the total energy of the asteroid may then be estimated, and the threat investigated thoroughly. Even with clarity as to how much energy an asteroid may deposit, a great deal of uncertainty still exists for the actual energy deposition process. One such source of uncertainty is the geometry of the incoming asteroid. The geometry of an asteroid will alter the stress distribution during entry, which adds uncertainty to when fracture will occur. Here, in this study, we use Smoothed Particle Hydrodynamics to model the atmospheric airburst of Tunguska-scale asteroids with varying geometric profiles, including a sphere, ellipsoid, binary and superellipsoid. Each asteroid is modeled as a homogenous structure with strength. We assess uncertainty through a series of planar 2D simulation cases for each geometry, comparing the source of stochasticity across geometries. A single 3D airburst simulation for each geometry is also analyzed. Additionally, the 3D cases are compared to the highly uncertain Tunguska event, predicting variance in burst height across geometries, but all bounded by theoretical burst heights proposed for Tunguska.

Airburst↗

NASA NTRS1972

An investigation of plastic fracture in aluminum alloys

The brittle fracture of many high strength alloys such as steel, titanium, and aluminum was shown to occur by a process called plastic fracture. According to this process microscopic voids form at impurity particles, then grow and coalesce to cause the final rupture. To further understand the role of impurities, four aluminum alloys were investigated: 2024-T851, 2124-T851, 7075-T7351 and 7079-T651. Fractography, quantitative metallography, and microprobe studies assessed the roles of various impurity particles relative to these alloys.

Low, J. R., Jr.↗

NASA NTRS2018

A Screening Method Using Pulsed-Power Combined with Infrared Imaging to Detect Pattern Defects in Bulk Metal Foil or Thin Film Resistors

Bulk metal foil and thin film resistors occasionally contain localized defects within the etched resistor pattern. Common defects of this type include in-line constrictions referred to as notches, unremoved resistor material bridges between adjacent pattern lines, and embedded non-conductive particles in the resistor material. Such defects are prone to fracture due to thermomechanical fatigue during powered operation, especially power cycling, resulting in positive resistance change and open circuit failure modes. Common screening methods of optical microscopy, short time overload power tests (e.g., 6.25x rated power for 5 seconds) and burn-in (e.g., 1.5x rated power for 100 hours) are useful, but they are not always effective at removing devices with such defects. An improved method has been developed to screen for localized resistor pattern defects. The method involves the application of brief, high power electrical pulses at a low duty cycle while inspecting the resistor with a high resolution, high speed infrared camera. The following test conditions were found to be suitable for this purpose: 6.25x rated power, 1 to 5 pulses, 50 ms pulse width and 10% duty cycle. During the power pulsing, localized constrictions in the resistor pattern are identifiable as hot spots via the infrared camera. Reject criteria can be established based on observations of hot spots. To assess its effectiveness, a total of two hundred eighty (280) surface mount foil resistors (40 each from 7 different lots) were screened using this infrared technique. The screening identified twenty-nine (29) resistors with significant hot spots in the resistor pattern. All 280 resistors were then subjected to an industry standard 10,000 hour life test at 1x rated power at 70°C with power cycled for 90 minutes on and 30 minutes off. During life testing, three resistors exhibited positive resistance change failure mode. All three failures were due to thermomechanical fatigue failure of localized bridge defects at the locations identified via infrared screening. The results of this evaluation illustrate the benefits of the pulsed-power infrared detection screening technique to identify reliability suspect foil or thin film resistors that may escape common screening methods.

screening↗

NASA NTRS2018

A Screening Method Using Pulsed-Power Combined with Infrared Imaging to Detect Pattern Defects in Bulk Metal Foil or Thin Film Resistors

screening↗

DOE OSTI2020

DOE-BU-26096-4

The infiltration of nanoparticle electrocatalysts into solid oxide fuel cell (SOFC) electrodes has been proven to produce a high density of electrochemically active sites, and reduce charge transfer polarization losses in SOFC electrodes. This is crucial for intermediate temperature operation, as these losses increase greatly at lower temperatures. Nickel-yttria stabilized zirconia (Ni-YSZ) cermets are low-cost, and exhibit excellent stability, but their main disadvantage stems from nickel coarsening and performance loss over their operational lifetimes. Infiltration of electrocatalyst nanoparticles has been shown to mitigate nickel coarsening and the consequent anode degradation. In this work, the effects of these infiltrants have been observed in a standard Ni-YSZ electrode. In addition to nickel, mixed ionic and electronic conducting (MIEC) phases have been infiltrated into Ni-YSZ scaffolds and their performance characterized using electrochemical impedance spectroscopy (EIS). Cross-sectional microscopy of fractured cells has been used to compare electrode microstructure and particle statistics. A model has been proposed to explain the origin of anode performance enhancement from nanoscale electrocatalysts.

Mo, Boshan↗

DOE OSTI2021

A Critical Review of the Physicochemical Impacts of Water Chemistry on Shale in Hydraulic Fracturing Systems

Hydraulic fracturing of unconventional hydrocarbon resources involves the sequential injection of a high-pressure, particle-laden fluid with varying pH’s to make commercial production viable in low permeability rocks. This process both requires and produces extraordinary volumes of water. The water used for hydraulic fracturing is typically fresh, whereas “flowback” water is typically saline with a variety of additives which complicate safe disposal. As production operations continue to expand, there is an increasing interest in treating and reusing this high-salinity produced water for further fracturing. Here in this paper we review the relevant transport and geochemical properties of shales, and critically analyze the impact of water chemistry (including produced water) on these properties. We discuss five major geochemical mechanisms that are prominently involved in the temporal and spatial evolution of fractures during the stimulation and production phase: shale softening, mineral dissolution, mineral precipitation, fines migration, and wettability alteration. A higher salinity fluid creates both benefits and complications in controlling these mechanisms. For example, higher salinity fluid inhibits clay dispersion, but simultaneously requires more additives to achieve appropriate viscosity for proppant emplacement. In total this review highlights the nuances of enhanced hydrogeochemical shale stimulation in relation to the choice of fracturing fluid chemistry.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Deformation and Fracture Behavior of Additively Manufactured 316L Stainless Steel

Tensile deformation and fracture behavior of an additively manufactured (AM) 316L stainless steel (SS) in the as-built, stress-relieved, and solution-annealed conditions was investigated using in situ tensile testing in a scanning electron microscope with an electron back scattering diffraction (SEM–EBSD) detector. Analyses were performed to discuss the characteristic deformation and fracture process of the fine-grained AM 316L SS with and without relaxation heat treatment. The as-built 316L showed the highest strength, and both post-build heat treatments lowered the strength of the alloy. Regardless of the post-build processing, the AM 316L SS showed overall higher strength but slightly lower ductility when compared to the wrought (WT) 316L SS. Analysis of EBSD data indicated that the characteristic microstructural features from AM, such as the complex and fine grain morphology, dislocation network, pores, and silicon-rich oxides, evolved and exerted various roles during the tensile deformation and fracture processes. Further, it was obvious that the interaction of dislocation slips with oxide particles and cavities (or pores) resulted in an accelerated cracking in AM 316L SS. Overall, however, their influence on mechanical behavior was limited, as the genuinely high ductility of 316L SS could help avoid any premature or brittle fracture.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Phase-field modeling of crack growth and mitigation in solid oxide cells

Fracture and crack growth is one of the main degradation mechanisms in solid oxide cells (SOCs). However, the modeling of crack growth in SOCs is challenging due to their complex microstructures and possible plasticity development within the Ni particles in Ni-based SOC electrodes. In this study, a phase-field fracture model is developed, which incorporates the SOC microstructures and phase-dependent material properties, including yield strength, fracture toughness in the bulk and at the interphase boundaries. The model is employed to study crack initiation and growth under thermal and redox cycling on the hydrogen electrode side of SOCs. The simulation results demonstrate that under thermal cycling, work-zone cracking dominates in electrolyte-supported SOCs with cracks initiated at the triple-phase boundaries, while only minor mechanical degradation occurs in hydrogen-electrode-supported SOCs after hundreds of thermal cycles. Under redox cycling, through-cracking of yttria-stabilized zirconia (YSZ) in the hydrogen electrode and electrolyte layers dominates. Finally, the simulation results suggest several crack-mitigation strategies, including decreasing the porosity in the hydrogen electrode support layer and synchronizing thermal strain to balance oxidation strain.

08 HYDROGEN↗

DOE OSTI2025

Micromechanical response of SiC-OPyC layers in TRISO fuel particles

Tristructural isotropic (TRISO)–coated particle fuel is a proposed fuel for multiple advanced reactor concepts. The performance of the particle depends on whether the silicon carbide (SiC) layer remains intact to prevent the release of metallic and gaseous fission products. Mechanical fracture of the SiC layer is a potential failure mode under various fuel configurations and operating environments, including the potential transmission of matrix-originating cracks through TRISO particles. Furthermore, this study uses instrumented indentation techniques on cross-sectioned surrogate particles to examine the mechanical stability of the critical interface between SiC and the outer pyrolytic carbon (OPyC) layer. The observed behavior at the interface is rationalized by examining the radially dependent fracture behavior of the SiC layer and performing a numerical analysis to quantify the residual stresses that develop during the processing and cross-sectioning of the as-fabricated particle. Characterizing the SiC-OPyC interface of surrogate TRISO particles using nanoindentation provides unique insight into the interface's room-temperature residual stress and mechanical stability. The modeling efforts were used to investigate the experimental procedure further, and the results are presented herein to validate this fuel form's potential mechanical failure modes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

A Systematic Interpretation of Subsurface Proppant Concentration from Drilling Mud Returns: Case Study from Hydraulic Fracturing Test Site (HFTS-2) in Delaware Basin

The aim of this study is generation and validation of a proppant log using analysis of drilling mud returns for child wells. Proppant log provides qualitative as well as quantitative insights into spatial distribution of proppant sand particles from prior stimulation of parent wells. While the basic methodology was developed and formalized during analysis of material collected from through fracture cores at Hydraulic Fracturing Test Site in Midland Basin (HFTS – 1), the test wells at HFTS – 2 in the neighboring Delaware Basin allowed the opportunity to validate the workflow on actual mud return samples from subsurface. As a child well is being drilled, periodic mud return samples are collected at the rig site and preserved for analysis. The workflow involves systematic cleaning of the samples including various steps such as washing, drying and segregation of samples into relevant size fractions of interest (< Mesh 20) based on specifications of pumped sand during stimulation of the parent well. Clean samples are imaged using high resolution transparency scanning. Scan images are then systematically analyzed for particles of interest using computer vision techniques. Sample counts are further validated using elemental analysis of smaller sub-samples at various depths of interest. This step is necessary to isolate proppant versus other naturally occurring minerals such as sulphates and carbonates which show similar optical properties. We successfully correlated proppant distribution against the existing parent well and validated propped versus relatively un-propped zones for a child well at the test site. The advantage of testing the proppant log concept at the HFTS – 2 site is the plethora of additional diagnostic data that is available to validate our primary observations. We can correlate spatial proppant distribution against variability in stimulation response based on independent observations such as image logs, microseismic attributes as well as DAS response, all of which tend to corroborate one another. One of our significant successes was being able to describe varying degrees of impact of the parent well along the lateral length of a stimulated child well. Our workflow represents a systematic and one-of-a-kind interpretation of spatial proppant distribution while drilling child wells. This provides unique opportunities to better understand the current state of the Downloaded from http://onepetro.org/URTECONF/proceedings-pdf/21URTC/2-21URTC/D021S031R003/2477415/urtec-2021-5189-ms.pdf/1 by Carol Worster on 28 February 2022 URTeC 5189 2 reservoir being targeted including zones which are likely more drained relative to others and how the planned completion of the child well can be improved. Lastly, this log can be useful is validating optimal well spacing in relatively new fields under development.

58 GEOSCIENCES↗