Results for “pressure diffusion” — Page 12

DOE OSTI2023

Water transport in reverse osmosis membranes is governed by pore flow, not a solution-diffusion mechanism

We performed nonequilibrium molecular dynamics (NEMD) simulations and solvent permeation experiments to unravel the mechanism of water transport in reverse osmosis (RO) membranes. The NEMD simulations reveal that water transport is driven by a pressure gradient within the membranes, not by a water concentration gradient, in marked contrast to the classic solution-diffusion model. We further show that water molecules travel as clusters through a network of pores that are transiently connected. Permeation experiments with water and organic solvents using polyamide and cellulose triacetate RO membranes showed that solvent permeance depends on the membrane pore size, kinetic diameter of solvent molecules, and solvent viscosity. This observation is not consistent with the solution-diffusion model, where permeance depends on the solvent solubility. Motivated by these observations, we demonstrate that the solution-friction model, in which transport is driven by a pressure gradient, can describe water and solvent transport in RO membranes.

42 ENGINEERING↗

DOE OSTI2025

Vacancy-Dependent Diffusion Mechanism in Oxygen-Defective SrFeO 3 Perovskite Materials: First-Principles Density Functional Theory and Experimental Approach

Understanding oxygen diffusion at the atomic scale in SrFeO 3−δ perovskites is crucial for developing oxygen storage materials with optimal performance. Such materials are required to have high stability, corrosion resistance, and acceptable oxygen storage capacity at moderate operating temperatures and pressures. Here, in this study, we used first-principles density functional theory and thermogravimetric analysis to study the vacancy-dependent oxygen diffusion in oxygen-deficient SrFeO 3−δ (δ = 0, 0.065, 0.125, 0.25, 0.5) perovskites. The electronic structures, including the partial- and spin-resolved density of states, for different SrFeO 3−δ phases were calculated and compared with available experimental and theoretical results. By mapping the migration pathways, we investigated diffusion mechanisms and calculated the energy barriers for oxygen diffusion in cubic, orthorhombic, and brownmillerite phases of SrFeO 3−δ perovskites. Using the calculated energy barriers, we deduced the diffusion time scales and diffusion coefficients within SrFeO 3−δ . A diffusion coefficient on the order of 10 –8 m 2 /s was obtained for SrFeO 2.875 . We experimentally investigated the roles of temperature and oxygen partial pressures on the redox kinetics and deduced the kinetics rate and diffusion density, which agreed well with the calculated values for the density of diffusing oxygen vacancy in the lattice. Our results showed that the energy barrier tends to reduce at higher oxygen concentrations. Our results serve as an important guideline for designing oxygen storage materials with optimal redox kinetics.

chemical looping with oxygen uncoupling (CLOU)↗

DOE OSTI2023

Structure–Transport Relationships of Water–Organic Solvent Co-transport in Carbon Molecular Sieve (CMS) Membranes

We explore the effects of the carbon molecular sieve (CMS) microstructure on the separation performance and transport mechanism of water–organic mixtures. Specifically, we utilize PIM-1 dense films and integrally skinned asymmetric hollow fiber membranes as polymer precursors for the CMS materials. The PIM-1 membranes were pyrolyzed under several different pyrolysis atmospheres (argon, carbon dioxide, and diluted hydrogen gas) and at multiple pyrolysis temperatures. Detailed gas physisorption measurements reveal that membranes pyrolyzed under 4% H 2 and CO 2 had broadened ultramicropore distributions (pore diameter <7 Å) compared to Ar pyrolysis, and pyrolysis under CO 2 increased ultramicropore volume and broadened micropore distributions at increased pyrolysis temperatures. Gravimetric water and p-xylene sorption and diffusion measurements reveal that the PIM-1-derived CMS materials are more hydrophilic than other CMS materials that have been previously studied, which leads to sorption-diffusion estimations showing water-selective permeation. Water permeation in the vapor phase, pervaporation, and liquid-phase hydraulic permeation reveal that the isobaric permeation modes (vapor permeation and pervaporation) are reasonably well predicted by the sorption-diffusion model, whereas the hydraulic permeation mode is significantly underpredicted (>250×). Conversely, the permeation of p-xylene is well predicted by the sorption-diffusion model in all cases. The collection of pore size analysis, vapor sorption and diffusion, and permeation in different modalities creates a picture of a combined transport mechanism in which water–under high transmembrane pressures–permeates via a Poiseuille-style mechanism, whereas p-xylene solutes in the mixture permeate via sorption-diffusion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

The design of a photoionization front experiment using the Z-Machine as a driving source and estimated measurements

Radiation-driven heat fronts are present in the early universe during reionization, the circumstellar medium of supernovae, and in high-energy-density physics experiments. Dedicated experiments to observe and diagnose the behavior of these types of heat fronts can improve our understanding of these phenomena. A simulation study of photoionization fronts using the HELIOS-CR radiation hydrodynamics code provides an experimental design for the Z-Machine at Sandia National Laboratory using a measurement-calibrated input radiation flux to drive the photoionization front. The simulations use detailed atomic physics and non-diffusive radiation transport in 1D to determine an optimal gas pressure of 0.75 atm for an experiment in N gas as well as the effects of increasing the thickness of the window that seals the gas cell. Post-processing of these simulations demonstrates that ratios of atomic rate coefficients place the heat front in a physics regime where photoionization dominates the energy deposition. Here, to see the sensitivity of the simulations to changes in the model and spatial grid, this analysis performed resolution, atomic model detail, and radiation transport angular grid studies showing less than 10% deviation from the nominal model for increased complexity, when possible. An effort to emulate 3D geometric effects on the radiation flux using an artificial attenuation scheme has shown that, even for conservative estimates of the flux, simulations still produce a photoionization front. Estimations of a streaked, visible spectroscopy measurement using SPECT3D showed that line emission measurements are present early in time and that later in time thermal emission should become dominant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Mass dependence of overshooting beneath convective envelopes

State of the art stellar evolution codes [Paxton et al., 2010, Demarque et al., 2004, Weiss and Schlattl, 2008, Siess et al., 2013, Christensen-Dalsgaard, 2008] evoke a diffusive process to model convective overshooting. The diffusion coefficient [Freytag et al., 1996, Pratt et al., 2017] used in the model can be set to change with the classification of the convective zone as non-burning, H-burning, He-burning, or metal-burning. It can also be set to change at defined evolutionary points, such as the bottom of the asymptotic giant branch, or during the third dredge up [Herwig, 2000, Lugaro et al., 2003]. Aside from these abrupt changes, the diffusion coefficient is typically locked to a percentage of the pressure scale height measured at the convective boundary. However, there is no theoretical reason for convective overshooting, or indeed other convective properties, to change in the same way that the pressure scale height changes as a star evolves.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2021

Role of surface diffusion in formation of unique reactivity for graphite oxidation: Time-resolved measurements in a pulsed diffusion reactor

Quantification of oxidation kinetics is essential to develop graphitic materials for diverse applications: from refractories found in gas-cooled nuclear reactors to catalysts needed for chemical manufacturing. In this work, using well-defined highly oriented pyrolytic graphite, low-pressure isotopic transient experiments combined with controlled annealing periods, we resolve the role of surface diffusion and quantify oxidation kinetics with nanomole-precision. We observe an unexpected increase in reactivity following annealing which is explained by the role of surface diffusion increasing the probability for trapping mobile oxygen at more reactive edge sites. Here, the locus of adsorption and spillover to the basal plane is distinct from the trapping location creating a more active oxygen species. Isotopic products reflect the population dynamics of oxygen added at the edge and surface diffusion that relocates basal plane oxygen to more reactive edge sites. Since this process proceeds in parallel with direct oxidation reactions, it is not likely to be observed using steady-state or conventional ‘bulk’ characterization techniques. Our unique time-resolved non-equilibrium measurement in a well-defined transport regime, enables observation of three distinct behaviors: short-term deactivation due to the balance of rates in oxygen supply/product formation, reactivity increases due to surface diffusion and longer-term reactivity increase with oxygen accumulation.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Experimental investigation of elemental and isotopic evaporation processes by laser heating in an aerodynamic levitation furnace

In this report we carried out evaporation experiments on a B-type calcium–aluminium-rich inclusion (CAI) melt in a gas-mixing aerodynamic levitation laser furnace, at 1873 K and an oxygen partial pressure of 10 -9.1 atm, for durations ranging from 60 to 600 s. Evaporation of SiO 2 and MgO follow the same trend as those observed in vacuum furnace experiments at the same temperature and starting composition, showing that their evaporation relative to one another from the melt is independent of pressure, oxygen fugacity, and hydrodynamical regime specific to the furnace. Isotopic ratios of Mg and Si in evaporation residues are used to derive fractionation factors of α 26/24 Mg vap-liq = 0.9906± 0.0004 and α 30/28 Si vap-lip = 0.9943±0.0003, which are both significantly closer to unity than those found for evaporation in a vacuum, which translates to less isotope fractionation. The residues are also less isotopically fractionated than expected for cases in which transport of the gas species away from the melt is diffusion-controlled at 1-atm. By analysing the flow regimes in our furnace, we find that advection by the levitating gas is the primary mode of mass transport away from the melt surface, as opposed to diffusion-limited transport in a vacuum or 1-atm tube furnace. A modified Hertz–Knudsen–Langmuir formulation accounts for this process, and shows that isotopic fractionation of both Si and Mg reflect a saturation factor (ratio of the pressure of the evaporating species to vapour saturation pressure) equal to 0.75. This is in perfect accord with recent measurements of Cu isotopic fractionation using a similar furnace. The fact that three elements (Mg, Si, Cu) with varying equilibrium vapour pressures, activity coefficients in the liquid, and diffusion coefficients in the gas have the same scaling behaviour to saturation pressure is a strong indication that the mechanism controlling evaporation is driven by the hydrodynamical regime imposed in the furnace. Therefore, this class of experiments can be used to constrain processes in which advection dominates over diffusion, such as (but not limited to) planetary ejecta, tektites, giant impacts, nebular condensation in a turbulent flow, or nuclear fallout material. Finally, the possibility to reach high temperatures (in excess of 3500 K) in this furnace allows it to be used to evaluate the activity coefficients of melt components in extreme conditions relevant to molten planetary interiors (i.e., magma oceans), with a specific focus on refractory elements.

58 GEOSCIENCES↗

DOE OSTI2021

A comprehensive analysis of transient pressure and rate data from CO 2 storage projects in a depleted pinnacle reef oil field complex, Michigan, USA

Pressure and rate data are commonly recorded as part of a basic monitoring program in CCS projects. This paper discusses the application of multiple analytical techniques to interpret pressure and rate transient data from CO 2 injection and storage operations. The techniques of interest, i.e., injection-falloff analysis, injectivity/productivity index analysis and pressure pulse arrival time analysis, are commonly used in the oil and gas industry to assess reservoir properties, but not well known in the CCS literature (especially the last two). Injection-falloff analysis involves log-log pressure derivative plotting for the falloff data and history-matching of the entire injection-falloff sequence to determine permeability. In the injectivity/productivity index analysis, rate-normalized pressure buildup is plotted against material balance time or ratio of cumulative injection to injection rate to determine the injectivity index (ratio of injection rate to stabilized pressure buildup) which can be related to the permeability-thickness product. The arrival time analysis identifies the arrival of a pressure disturbance (~0.1 psi change from ambient) to determine the hydraulic diffusivity from which permeability can be estimated. The applicability of these techniques is demonstrated via illustrative examples from multiple wells in different pinnacle carbonate reefs undergoing CO 2 -EOR in Northern Michigan. The paper ends with a discussion of the relative merits of each interpretive technique, as well as recommendations that could be useful for other field projects.

42 ENGINEERING↗

DOE OSTI2021

Forming mechanism of equilibrium and non-equilibrium metallurgical phases in dissimilar aluminum/steel (Al–Fe) joints

Abstract Forming metallurgical phases has a critical impact on the performance of dissimilar materials joints. Here, we shed light on the forming mechanism of equilibrium and non-equilibrium intermetallic compounds (IMCs) in dissimilar aluminum/steel joints with respect to processing history (e.g., the pressure and temperature profiles) and chemical composition, where the knowledge of free energy and atomic diffusion in the Al–Fe system was taken from first-principles phonon calculations and data available in the literature. We found that the metastable and ductile (judged by the presently predicted elastic constants) Al 6 Fe is a pressure ( P ) favored IMC observed in processes involving high pressures. The MoSi 2 -type Al 2 Fe is brittle and a strong P -favored IMC observed at high pressures. The stable, brittle η-Al 5 Fe 2 is the most observed IMC (followed by θ-Al 13 Fe 4 ) in almost all processes, such as fusion/solid-state welding and additive manufacturing (AM), since η-Al 5 Fe 2 is temperature-favored, possessing high thermodynamic driving force of formation and the fastest atomic diffusivity among all Al–Fe IMCs. Notably, the ductile AlFe 3 , the less ductile AlFe, and most of the other IMCs can be formed during AM, making AM a superior process to achieve desired IMCs in dissimilar materials. In addition, the unknown configurations of Al 2 Fe and Al 5 Fe 2 were also examined by machine learning based datamining together with first-principles verifications and structure predictions. All the IMCs that are not P- favored can be identified using the conventional equilibrium phase diagram and the Scheil-Gulliver non-equilibrium simulations.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Fast permeability measurement for tight reservoir cores using only initial data of the one chamber pressure pulse decay test

Here, in this study, a mathematical model for fast determination of the permeabilities of tight rocks using measurements taken from the initial period of the One Chamber Pressure Pulse Decay (OC-PPD) test is presented. The model applies to measurements taken both before and after the pressure pulse front has reached the downstream end of the specimen. The analytical solutions for the pressure decay in the upstream chamber are derived based on a parabolic arc approximation of pore pressure distribution along the test specimen. This approximation allows converting the initial–boundary value problem of fluid diffusion in the specimen, governed by partial differential equations, to a system of ordinary differential equations that can be easily solved by explicit formulae. Thus, an explicit formula for the pressure decay rate is obtained, which enables inverse analysis of the initial experimental data to estimate the rock permeability. The proposed method expedites the pulse decay test as it does not require the system to reach equilibrium. The method is validated with three sets of experimental data of the OC-PPD test using helium as the diffusing fluid, for which the relative error of the permeability is found to be less than 6%. This method is particularly useful if the equilibrium time of the pulse decay test for rock specimens with permeabilities in the range of nano-Darcy takes hours or days.

early-time solution↗

DOE OSTI2021

Optimal Header Design for Diffusion Bonded Heat Exchangers

Microchannel heat exchangers have seen increasing adoption in many high-pressure applications in recent decades but are subject to particulate fouling from the relatively small channel size compared to traditional designs. Typical cleaning methods require process shutdown, heat exchanger removal, cleaning, then reassembly. The objective of this project was to refine and transfer technology to enable header design improvements for Cleaning-in-Place (CIP), allowing for reduced/negligible process interruption for the cleaning process. The technology transfer was from Sandia National Laboratories (Sandia) to Vacuum Process Engineering, Inc. (VPE). This primary purpose of CIP was developed while considering channel flow uniformity and heat exchanger cost. The project phases were to 1) capture and define potential improvement options, 2) evaluate options with both simulation and experiments, and 3) transfer design knowledge to the industry partner. These efforts resulted in improved header designs from the first known focused effort in this area. The improved designs will help the entire microchannel heat exchanger field that has applications in supercritical CO 2 power cycles, hydrogen (fuel cell) vehicle fueling, liquified natural gas processing, and more.

42 ENGINEERING↗

DOE OSTI2020

Diffusivity and Structure of Room Temperature Ionic Liquid in Various Organic Solvents

Room-temperature ionic liquids (RTILs) hold promise for applications in electric double layer capacitors (EDLCs), owing to a much wider potential window, lower vapor pressure, and better thermal and chemical stabilities compared to conventional aqueous and organic electrolytes. However, because the low diffusivity of ions in neat RTILs negates the EDLCs’ advantage of high power density, the ionic liquids are often used in mixture with organic solvents. In this study, we measured the diffusivity of cations and anions in RTIL, 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl) ([BMIM + ][TFSI – ]), mixed with 10 organic solvents, by using the pulsed-field gradient NMR method. The ion diffusivity was found to follow that of neat solvents and in most studied solvents showed an excellent agreement with the predicted values reported in the recent molecular dynamics (MD) study [Thompson, M. W.; J. Phys. Chem. B 2019, 123, 1340-1347]. In two solvents consisting of long-chain molecules, however, the MD simulations predictions slightly underestimated the ionic diffusivities. The degree of ion dissociation was also estimated for each solvent by comparing the ionic conductivity with the molar conductivity derived from the diffusion measurements. The degree of ion dissociation and the hydrodynamic radius of ions suggest that the ions are coordinated by ~1 solvent molecule. Finally, the scarcity of solvent–ion interactions explains the fact that the diffusivity of ions in the mixture significantly depends on the viscosity of the solvent.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Final-stage densification kinetics of direct current–sinteredZrB2

Final-stage sintering was analyzed for nominally phase pure zirconium diboride synthesized by borothermal reduction of high-purity ZrO2. Analysis was conducted on ZrB2 ceramics with relative densities greater than 90% using the Nabarro–Herring stress–directed vacancy diffusion model. Temperatures of 1900°C or above and an applied uniaxial pressure of 50 MPa were required to fully densify ZrB2 ceramics by direct current sintering. Ram travel data were collected and used to determine the relative density of the specimens during sintering. Specimens sintered between 1900 and 2100°C achieved relative densities greater than 97%, whereas specimens sintered below 1900°C failed to reach the final stage of sintering. The average grain size ranged from 1.0 to 14.7 μm. The activation energy was calculated from the slope of an Arrhenius plot that used the Kalish equation. The activation energy was 162 ± 34 kJ/mol, which is consistent with the activation energy for dislocation movement in ZrB2. The diffusion coefficients for dislocation motion that controls densification were 5.1 × 10−6 cm2/s at 1900°C and 5.1 × 10−5 cm2/s at 2100°C, as calculated from activation energy and average grain sizes. This study provides evidence that the dominant mechanism for final-stage sintering of ZrB2 ceramics is dislocation motion.

36 MATERIALS SCIENCE↗

DOE OSTI2026

A Scaling Study for Incompressible Multispecies Solver in Vertex-CFD

Multispecies incompressible flows occur widely in engineering and environmental applications, such as chemical reactors, fuel cells, ocean mixing, and biomedical systems. However, accurately resolving the complex transport and mixing phenomena associated with multiple interacting species remains computationally challenging, especially for large-scale problems. In this study, we present a robust, high-performance computing--enabled multispecies incompressible Navier–Stokes solver integrated within the Vertex-CFD framework. Our solver employs a fully coupled, implicit, finite element--based formulation that accurately captures the advection, diffusion, and interaction of multiple species in incompressible flows by leveraging the Kokkos library for parallel computing to achieve high computational efficiency. For pressure coupling, the entropically damped artificial compressibility method is utilized. We validated the solver against canonical test cases, including multispecies advection, diffusion, and Bateman systems; the results demonstrate second- and third-order spatial accuracy and consistent convergence. Additionally, we demonstrated the strong and weak scaling study results obtained on the leadership-class high-performance computing system, Frontier at Oak Ridge National Laboratory.

Oz, Furkan [ORNL] (ORCID:0000000265831724)↗

DOE OSTI2023

Recent Developments in Hydrogeologic Applications for Strain Tensor Analyses

Changes in fluid pressure deform porous media and this effect occurs in a variety of hydrogeologic processes, from the change in storage during pumping or injection to fluctuations in water levels caused by barometric pressure. We have developed instruments for measuring small strains in porous media, and we have used the resulting strain data to evaluate well testing, hydraulic fracturing, manual loading at the ground surface, and ambient hydrologic processes, like rainfall and evaporation. A particularly important application is the use of strain tensor data measured at shallow depths to analyze well tests or hydraulic fractures conducted at much greater depths. An early demonstration of this technique was conducted at the North Avant Field north of Tulsa, Oklahoma, where Pennsylvanian sandstone creates a confined aquifer and oil reservoir at a depth of 530m. We have showed that the strains caused by injecting into the aquifer could be measured at a depth of 30m and used to evaluate the properties of the aquifer. We recently expanded the array of strainmeters at the North Avant Field by deploying three more instruments at shallow depth (30m) along with a deep instrument at 520m depth in the winter, 2021. The deep instrument is deployed in shale caprock slightly above the aquifer. To our knowledge, the deep strainmeter at the North Avant Field is the deepest strainmeter ever deployed and this required refining methods originally developed for shallow deployments. The instrument was lowered to depth on oil field tubing and cemented in place using techniques and materials developed for use in oil wells. Optical fiber used to communicate with the instrument was cemented in the annulus on the outside of tubing. This is significant because the techniques we used could readily be extended to greater depth, suggesting that strainmeters can be deployed over a wide range of depths for monitoring critical subsurface processes. For example, it suggests that strainmeters could be deployed through the caprock to monitor for leaks from underlying CO2 storage reservoirs. The strainmeter array at the North Avant Field has been used to characterize deformation during a series of injection tests in the spring and summer, 2021. All the new strainmeters respond to pumping, and the strainmeters we installed earlier also responded. To our knowledge, this is the first application of well testing in a deep aquifer that was monitored by an array of strainmeters—our earlier work used strainmeters at a single location. We are currently analyzing the strain data using an analytical solution, a proxy-based Bayesian inversion algorithm, and other methods. Strainmeter data has also been used to characterize periodic pumping tests by us and Riley Blais. A periodically varying pumping rate causes both hydraulic head and strain signals that vary with the same period as the pumping. The peaks and troughs of the head in monitoring wells lag behind the peaks and troughs of the head in the pumping well, and this lag time increases with distance from the pumping well. The lag time of the pressure and the distance to the monitoring well can be used in a simple analysis to estimate the hydraulic diffusivity of the aquifer. The lag time determined from strain data can be used to estimate aquifer properties using the same analysis that works for the pressure only for strain data measured at particular locations. That is because the strain field in a confining unit advances upward, laterally and then downward even though the pressure in the underlying aquifer only advances laterally, according to our recent simulations. We have field data showing that a small periodic signal superimposed on an injection rate at the North Avant Field will create a periodic strain signal at shallow strainmeters. The field data and the recent simulations suggest that including a periodic component to injection or pumping and then monitoring the resulting strain signal could be a way to monitor the subsurface.

Murdoch, Larry↗

DOE OSTI2023

Recent Developments in Hydrogeologic Applications for Strain Tensor Analyses

Changes in fluid pressure deform porous media and this effect occurs in a variety of hydrogeologic processes, from the change in storage during pumping or injection to fluctuations in water levels caused by barometric pressure. We have developed instruments for measuring small strains in porous media, and we have used the resulting strain data to evaluate well testing, hydraulic fracturing, manual loading at the ground surface, and ambient hydrologic processes, like rainfall and evaporation. A particularly important application is the use of strain tensor data measured at shallow depths to analyze well tests or hydraulic fractures conducted at much greater depths. An early demonstration of this technique was conducted at the North Avant Field north of Tulsa, Oklahoma, where Pennsylvanian sandstone creates a confined aquifer and oil reservoir at a depth of 530m. We have showed that the strains caused by injecting into the aquifer could be measured at a depth of 30m and used to evaluate the properties of the aquifer. We recently expanded the array of strainmeters at the North Avant Field by deploying three more instruments at shallow depth (30m) along with a deep instrument at 520m depth in the winter, 2021. The deep instrument is deployed in shale caprock slightly above the aquifer. To our knowledge, the deep strainmeter at the North Avant Field is the deepest strainmeter ever deployed and this required refining methods originally developed for shallow deployments. The instrument was lowered to depth on oil field tubing and cemented in place using techniques and materials developed for use in oil wells. Optical fiber used to communicate with the instrument was cemented in the annulus on the outside of tubing. This is significant because the techniques we used could readily be extended to greater depth, suggesting that strainmeters can be deployed over a wide range of depths for monitoring critical subsurface processes. For example, it suggests that strainmeters could be deployed through the caprock to monitor for leaks from underlying CO2 storage reservoirs. The strainmeter array at the North Avant Field has been used to characterize deformation during a series of injection tests in the spring and summer, 2021. All the new strainmeters respond to pumping, and the strainmeters we installed earlier also responded. To our knowledge, this is the first application of well testing in a deep aquifer that was monitored by an array of strainmeters—our earlier work used strainmeters at a single location. We are currently analyzing the strain data using an analytical solution, a proxy-based Bayesian inversion algorithm, and other methods. Strainmeter data has also been used to characterize periodic pumping tests by us and Riley Blais. A periodically varying pumping rate causes both hydraulic head and strain signals that vary with the same period as the pumping. The peaks and troughs of the head in monitoring wells lag behind the peaks and troughs of the head in the pumping well, and this lag time increases with distance from the pumping well. The lag time of the pressure and the distance to the monitoring well can be used in a simple analysis to estimate the hydraulic diffusivity of the aquifer. The lag time determined from strain data can be used to estimate aquifer properties using the same analysis that works for the pressure only for strain data measured at particular locations. That is because the strain field in a confining unit advances upward, laterally and then downward even though the pressure in the underlying aquifer only advances laterally, according to our recent simulations. We have field data showing that a small periodic signal superimposed on an injection rate at the North Avant Field will create a periodic strain signal at shallow strainmeters. The field data and the recent simulations suggest that including a periodic component to injection or pumping and then monitoring the resulting strain signal could be a way to monitor the subsurface.

Murdoch, Larry↗

DOE OSTI2025

Assessment of integral models for non-Boussinesq lazy plumes using numerical simulations

Integral modelling of turbulent buoyant plumes is crucial for rapid predictions of plume characteristics. While the governing equations are typically derived using self-similarity and a Boussinesq approximation, these assumptions may not hold for plumes originating from finite-area sources with large density ratios. Here, this work evaluates the accuracy of integral-scale models for non-Boussinesq lazy plumes using high-fidelity numerical simulations of turbulent helium plumes. We analyse the plume kinematics by computing vertical fluxes, plume radius and radial profiles, establishing some disparities between common practice and physical accuracy. We identify how the definition of the plume radius changes the perception of the plume structure when the flow is not self-similar and derive a relationship between the flux-based and threshold-based definitions without requiring self-similarity. We then examine the plume dynamics by evaluating the source terms from the governing plume equations. Our results support neglecting diffusive and viscous effects but emphasise the importance of the mean pressure gradient, even in the self-similar regime. Two coefficients need to be modelled: the well-known entrainment coefficient and the lesser-known momentum correction coefficient, which is a correction required for the momentum equation to account for self-similar and slender approximations. The momentum correction coefficient is found to be approximately constant and slightly greater than the assumed value of 1. The standard entrainment coefficient models perform well up to a local Richardson number three times the asymptotic value but overpredict entrainment for larger Richardson numbers. We propose a correction using the known finite limit of entrainment at infinite Richardson number.

Meehan, Michael Alexander [Sandia National Laborat↗

DOE OSTI2024

Impact of the Out‐Of‐Plane Flow Shear on Magnetic Reconnection at the Flanks of Earth's Magnetopause

Abstract Magnetic reconnection changes the magnetic field topology and facilitates the energy and particle exchange at magnetospheric boundaries such as the Earth's magnetopause. The flow shear perpendicular to the reconnecting plane prevails at the flank magnetopause under southward interplanetary magnetic field conditions. However, the effect of the out‐of‐plane flow shear on asymmetric reconnection is an open question. In this study, we utilize kinetic simulations to investigate the impact of the out‐of‐plane flow shear on asymmetric reconnection. By systematically varying the flow shear strength, we analyze the flow shear effects on the reconnection rate, the diffusion region structure, and the energy conversion rate. We find that the reconnection rate increases with the upstream out‐of‐plane flow shear, and for the same upstream conditions, it is higher at the dusk side than at the dawn side. The diffusion region is squeezed in the outflow direction due to magnetic pressure which is proportional to the square of the Alfvén Mach number of the shear flow. The out‐of‐plane flow shear increases the energy conversion rate , and for the same upstream conditions, the magnitude of is larger at the dusk side than at the dawn side. This study reveals that out‐of‐plane flow shear not only enhances the reconnection rate but also significantly boosts energy conversion, with more pronounced effects on the dusk‐side flank than on the dawn‐side flank. These insights pave the way for better understanding the solar wind‐magnetosphere interactions.

Liang, Haoming↗