Search NASA⌕ Search

SEARCH · Search NASA

Results for “projection method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Arbitrary multisite two-photon excitation in four dimensions

We demonstrate dynamic and arbitrary multisite two-photon excitation in three dimensions using the holographic projection method. Rapid response (fourth dimension) is achieved through high-speed noniterative calculation of the hologram using a video graphics accelerator board. We verify that the projected asymmetric spot configurations have sufficient spatiotemporal photon density for localized two-photon excitation. This system is a significant advance and can be applied to time-resolved photolysis of caged compounds in biological cells and complex neuronal networks, nonlinear microfabrication and volume holographic optical storage.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

WE-G-BRF-05: Feasibility of Markerless Motion Tracking Using Dual Energy Cone Beam Computed Tomography (DE-CBCT) Projections

Purpose: To compare markerless template-based tracking of lung tumors using dual energy (DE) cone-beam computed tomography (CBCT) projections versus single energy (SE) CBCT projections. Methods: A RANDO chest phantom with a simulated tumor in the upper right lung was used to investigate the effectiveness of tumor tracking using DE and SE CBCT projections. Planar kV projections from CBCT acquisitions were captured at 60 kVp (4 mAs) and 120 kVp (1 mAs) using the Varian TrueBeam and non-commercial iTools Capture software. Projections were taken at approximately every 0.53° while the gantry rotated. Due to limitations of the phantom, angles for which the shoulders blocked the tumor were excluded from tracking analysis. DE images were constructed using a weighted logarithmic subtraction that removed bony anatomy while preserving soft tissue structures. The tumors were tracked separately on DE and SE (120 kVp) images using a template-based tracking algorithm. The tracking results were compared to ground truth coordinates designated by a physician. Matches with a distance of greater than 3 mm from ground truth were designated as failing to track. Results: 363 frames were analyzed. The algorithm successfully tracked the tumor on 89.8% (326/363) of DE frames compared to 54.3% (197/363) of SE frames (p<0.0001). Average distance between tracking and ground truth coordinates was 1.27 +/− 0.67 mm for DE versus 1.83+/−0.74 mm for SE (p<0.0001). Conclusion: This study demonstrates the effectiveness of markerless template-based tracking using DE CBCT. DE imaging resulted in better detectability with more accurate localization on average versus SE. Supported by a grant from Varian Medical Systems.

60 APPLIED LIFE SCIENCES↗

Operators for scattering of particles with spin

Operators for simulating the scattering of two particles with spin are constructed. Three methods are shown to give the consistent lattice operators for PN, PV, VN and NN scattering, where P, V and N denote pseudoscalar meson, vector meson and nucleon. The projection method leads to one or several operators OG;r;n that transform according to a given irreducible representation G and row r. However, it gives little guidance on which continuum quantum numbers of total J, spin S, orbital momentum L or single-particle helicities l1;2 will be related with a given operator. This is remedied with the helicity and partial-wave methods. There first the operators with good continuum quantum numbers (J;P;l1;2) or (J;L;S) are constructed and then subduced to the irreps G of the discrete lattice group. The results indicate which linear combinations OG;r;n of various n have to be employed in the simulations in order to enhance couplings to the states with desired continuum quantum numbers. The total momentum of two hadrons is restricted to zero since parity P is a good quantum number in this case.

Prelovsek, Sasa↗

Observations and seismoacoustic simulations of earthquake-generated infrasound waves in non-epicentral regions

We analysed infrasound waves associated with the Gyeongju earthquake (ML 5.8) that occurred on 2016 September 12, in the southeastern Korean Peninsula. For infrasound wave detection, the Progressive Multichannel Correlation method was applied to the infrasound data set recorded at seven arrays operating in South Korea at epicentral distances ranging from 178 to 472 km. Based on the back-projection method constrained by array-dependent celerity and azimuth deviation models, the source regions were identified in both the epicentral and non-epicentral regions. Remarkably, the non-epicentral secondary sources of this earthquake were located in regions with shallow water depths: (i) the western coastal area in the Yellow Sea and (ii) the shallow ocean basin and bank in the East Sea. The location results obtained from the earthquake could be corroborated through its foreshock (ML 5.1), yielding location results consistent with those of the main shock. The generation of infrasound waves over shallow water depths was fortuitously validated by direct recordings of dominant single-frequency (~0.3 Hz) infrasound waves at close range via temporary sensors near the ocean basin and bank. We interpreted that low-frequency infrasound signals could be generated from interactions among the ocean floor, shallow seawater and atmosphere. We performed numerical simulations of seismoacoustic fields to predict ground motions on the seafloor and acoustic transmission efficiency between the water and air interface. The simulations quantified the energy transfer through different media and clarified our observational results. We found that because this solid Earth‒water‒atmosphere coupled air wave has a relatively low frequency (~0.3 Hz), it can survive propagation over long distances compared with high-frequency infrasound waves generated in inland and mountain regions. In this study, we extend our understanding of water‒atmosphere coupling and the monitoring framework for earthquake-associated non-epicentral infrasound waves, encompassing not only inland ground shaking but also shallow sea regions located far from the epicentre.

Earthquake monitoring and test-ban treaty verifica↗

Comparison of Artificial Compressibility Methods for Coupled Laminar Fluid Flow and Heat Transfer

Artificial compressibility (AC) methods for incompressible flows perturb the mass continuity equation by the time derivative of the pressure field to achieve direct coupling between pressure and velocity without the need for a projection method. Several variations of the original AC method have been proposed (e.g., the entropically damped artificial compressibility [EDAC] method) that can, in some scenarios, improve on the original model. In this paper, we methodically compare the results of the original AC model and the EDAC model for both steady-state and transient problems with coupling between the momentum and energy equations. We demonstrate that the EDAC model and the AC model yield similar numerical results, and the EDAC model is 10%-20% faster than the AC model for a given problem.

Oz, Furkan [ORNL] (ORCID:0000000265831724)↗

Solving Stochastic Dynamic Programming Problems: A Mixed Complementarity Approach

We detail a mixed complementarity problem (MCP) formulation of continuous state dynamic programming problems (DP-MCP). We write the solution to projection methods in value function iteration (VFI) as a joint set of optimality conditions that characterize maximization of the Bellman equation; and approximation of the value function. The MCP approach replaces the iterative component of projection based VFI with a one-shot solution to a square system of complementary conditions. We provide three numerical examples to illustrate our approach.

97 MATHEMATICS AND COMPUTING↗

Supply and Demand for Radiation Oncology in the United States: Updated Projections for 2015 to 2025

Purpose: Prior studies have forecasted demand for radiation therapy to grow 10 times faster than the supply between 2010 and 2020. We updated these projections for 2015 to 2025 to determine whether this imbalance persists and to assess the accuracy of prior projections. Methods and Materials: The demand for radiation therapy between 2015 and 2025 was estimated by combining current radiation utilization rates determined by the Surveillance, Epidemiology, and End Results data with population projections provided by the US Census Bureau. The supply of radiation oncologists was forecast by using workforce demographics and full-time equivalent (FTE) status provided by the American Society for Radiation Oncology (ASTRO), current resident class sizes, and expected survival per life tables from the US Centers for Disease Control. Results: Between 2015 and 2025, the annual total number of patients receiving radiation therapy during their initial treatment course is expected to increase by 19%, from 490,000 to 580,000. Assuming a graduating resident class size of 200, the number of FTE physicians is expected to increase by 27%, from 3903 to 4965. In comparison with prior projections, the new projected demand for radiation therapy in 2020 dropped by 24,000 cases (a 4% relative decline). This decrease is attributable to an overall reduction in the use of radiation to treat cancer, from 28% of all newly diagnosed cancers in the prior projections down to 26% for the new projections. By contrast, the new projected supply of radiation oncologists in 2020 increased by 275 FTEs in comparison with the prior projection for 2020 (a 7% relative increase), attributable to rising residency class sizes. Conclusion: The supply of radiation oncologists is expected to grow more quickly than the demand for radiation therapy from 2015 to 2025. Further research is needed to determine whether this is an appropriate correction or will result in excess capacity.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Nonintrusive projection-based reduced order modeling using stable learned differential operators

Nonintrusive projection-based reduced order models (ROMs) are essential for dynamics prediction in multi-query applications where underlying governing equations are known but the access to the source of the underlying full order model (FOM) is unavailable; that is, FOM is a glass-box. This article proposes a learn-then-project approach for nonintrusive model reduction. In the first step of this approach, high-dimensional stable sparse learned differential operators (S-LDOs) are determined using the generated data. In the second step, the ordinary differential equations, comprising these S-LDOs, are used with suitable dimensionality reduction and low-dimensional subspace projection methods to provide equations for the evolution of reduced states. This approach allows easy integration into the existing intrusive ROM framework to enable nonintrusive model reduction while allowing the use of Petrov–Galerkin projections. The applicability of the proposed approach is demonstrated for Galerkin and LSPG projection-based ROMs through four numerical experiments: 1-D scalar advection, 1-D Burgers, 2-D scalar advection and 1-D scalar advection–diffusion–reaction equations. In conclusion, the results indicate that the proposed nonintrusive ROM strategy provides accurate and stable dynamics prediction.

42 ENGINEERING↗

Benchmarking Surface Tension Measurement Method using two Oscillation Modes in Levitated Liquid Metals

The Faraday forcing method in levitated liquid droplets has recently been introduced as a method for measuring surface tension using resonance. By subjecting an electrostatically-levitated liquid metal droplet to a continuous, oscillatory, electric field, at a frequency nearing that of the droplet’s first principal mode of oscillation (known as mode 2), the method was previously shown to determine surface tension of materials that would be particularly difficult to process by other means, e.g. liquid metals and alloys. It also offers distinct advantages in future work involving high viscosity samples because of the continuous forcing approach. This work presents 1) a benchmarking experimental method to measure surface tension by excitation of the second principal mode of oscillation (known as mode 3) in a levitated liquid droplet and 2) a more rigorous quantification of droplet excitation using a projection method. Surface tension measurements compare favorably to literature values for Zirconium, Inconel 625, and Rhodium, using both modes 2 and 3. Thus, this new method serves as a credible, self-consistent benchmarking technique for the measurement of surface tension

Levitation↗

An Evolve-Then-Correct Reduced Order Model for Hidden Fluid Dynamics

In this paper, we put forth an evolve-then-correct reduced order modeling approach that combines intrusive and nonintrusive models to take hidden physical processes into account. Specifically, we split the underlying dynamics into known and unknown components. In the known part, we first utilize an intrusive Galerkin method projected on a set of basis functions obtained by proper orthogonal decomposition. We then present two variants of correction formula based on the assumption that the observed data are a manifestation of all relevant processes. The first method uses a standard least-squares regression with a quadratic approximation and requires solving a rank-deficient linear system, while the second approach employs a recurrent neural network emulator to account for the correction term. We further enhance our approach by using an orthonormality conforming basis interpolation approach on a Grassmannian manifold to address off-design conditions. The proposed framework is illustrated here with the application of two-dimensional co-rotating vortex simulations under modeling uncertainty. The results demonstrate highly accurate predictions underlining the effectiveness of the evolve-then-correct approach toward real-time simulations, where the full process model is not known a priori.

long short-term memory↗

Extension of the noise propagation matrix method for higher mode solutions

The noise propagation matrix method (NPMM) has been extended to get higher mode solutions. Previous studies show that the NPMM can be used to compute the dominance ratio of a system. It is essentially the same as the Coarse Mesh Projection Method (CMPM), both of which use the noise propagation matrix (NPM) to determine the dominance ratio, either after finishing the Monte Carlo simulation or on-the-fly during the simulation. Since only the fundamental fission source information is explicitly utilized while the higher mode information is implicitly contained in the statistical noises, the NPMM can usually only give an approximate estimation of the dominance ratio after thousands of cycles. In this study, the NPMM is extended by simulating the higher modes explicitly, so that the dominance ratio estimation can be more accurate and efficient. Besides, the higher mode solutions can be obtained at the same time with good accuracy and efficiency.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Preconditioned least‐squares Petrov–Galerkin reduced order models

Abstract In this article, we introduce a methodology for improving the accuracy and efficiency of reduced order models (ROMs) constructed using the least‐squares Petrov–Galerkin (LSPG) projection method through the introduction of preconditioning. Unlike prior related work, which focuses on preconditioning the linear systems arising within the ROM numerical solution procedure to improve linear solver performance, our approach leverages a preconditioning matrix directly within the minimization problem underlying the LSPG formulation. Applying preconditioning in this way has the potential to improve ROM accuracy for several reasons. First, preconditioning the LSPG formulation changes the norm defining the residual minimization, which can improve the residual‐based stability constant bounding the ROM solution's error. The incorporation of a preconditioner into the LSPG formulation can have the additional effect of scaling the components of the residual being minimized to make them roughly of the same magnitude, which can be beneficial when applying the LSPG method to problems with disparate scales (e.g., dimensional equations, multi‐physics problems). Importantly, we demonstrate that an “ideal preconditioned” LSPG ROM (a ROM in which the preconditioner is the inverse of the Jacobian of its corresponding full order model) emulates projection of the full order model solution increment onto the reduced basis. This quantity defines a lower bound on the error of a ROM solution for a given reduced basis. By designing preconditioners that approximate the Jacobian inverse—as is common in designing preconditioners for solving linear systems—it is possible to obtain a ROM whose error approaches this lower bound. The proposed approach is evaluated on several mechanical and thermo‐mechanical problems implemented within the Albany HPC code and run in the predictive regime, with prediction across material parameter space. We demonstrate numerically that the introduction of simple Jacobi, Gauss‐Seidel, and ILU preconditioners into the proper orthogonal decomposition/LSPG formulation reduces significantly the ROM solution error, the reduced Jacobian condition number, the number of nonlinear iterations required to reach convergence, and the wall time (thereby improving efficiency). Moreover, our numerical results reveal that the introduction of preconditioning can deliver a robust and accurate solution for test cases in which the unpreconditioned LSPG method fails to converge.

Lindsay, Payton↗

Data consistency conditions for truncated fanbeam and parallel projections

Purpose: In image reconstruction from projections, data consistency conditions (DCCs) are mathematical relationships that express the overlap of information between ideal projections. DCCs have been incorporated in image reconstruction procedures for positron emission tomography, single photon emission computed tomography, and x-ray computed tomography (CT). Building on published fanbeam DCCs for nontruncated projections along a line, the authors recently announced new DCCs that can be applied to truncated parallel projections in classical (two-dimensional) image reconstruction. These DCCs take the form of polynomial expressions for a weighted backprojection of the projections. The purpose of this work was to present the new DCCs for truncated parallel projections, to extend these conditions to truncated fanbeam projections on a circular trajectory, to verify the conditions with numerical examples, and to present a model of how DCCs could be applied with a toy problem in patient motion estimation with truncated projections. Methods: A mathematical derivation of the new parallel DCCs was performed by substituting the underlying imaging equation into the mathematical expression for the weighted backprojection and demonstrating the resulting polynomial form. This DCC result was extended to fanbeam projections by a substitution of parallel to fanbeam variables. Ideal fanbeam projections of a simple mathematical phantom were simulated and the DCCs for these projections were evaluated by fitting polynomials to the weighted backprojection. For the motion estimation problem, a parametrized motion was simulated using a dynamic version of the mathematical phantom, and both noiseless and noisy fanbeam projections were simulated for a full circular trajectory. The fanbeam DCCs were applied to extract the motion parameters, which allowed the motion contamination to be removed from the projections. A reconstruction was performed from the corrected projections. Results: The mathematical derivation revealed the anticipated polynomial behavior. The conversion to fanbeam variables led to a straight-forward weighted fanbeam backprojection which yielded the same function and therefore the same polynomial behavior as occurred in the parallel case. Plots of the numerically calculated DCCs showed polynomial behavior visually indistinguishable from the fitted polynomials. For the motion estimation problem, the motion parameters were satisfactorily recovered and ten times more accurately for the noise-free case. The reconstructed images showed that only a faint trace of the motion blur was still visible after correction from the noisy motion-contaminated projections. Conclusions: New DCCs have been established for fanbeam and parallel projections, and these conditions have been validated using numerical experiments with truncated projections. It has been shown how these DCCs could be applied to extract parameters of unwanted physical effects in tomographic imaging, even with truncated projections.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Coordinated Ramping Product and Regulation Reserve Procurements in CAISO and MISO using Multi-Scale Probabilistic Solar Power Forecasts (Pro2R)

How can probabilistic solar forecasts lower costs and improve reliability for independent system operator (ISO) markets? We tackle this question in three steps. First, we enhance an existing solar forecasting system to provide well-calibrated hours-ahead probabilistic forecasts. We then relate the degree of uncertainty in those forecasts to error distributions for net load ramps for the California ISO (CAISO) using statistical and machine learning methods. Projected net load errors conditioned on solar uncertainty are translated into flexible ramp requirements that therefore reflect real-time meteorological and solar conditions, improving on typical ISO procedures. Finally, a multi-period look-ahead production cost model quantifies how conditional ramp requirements can a) decrease operating costs by lowering requirements compared to often conservative unconditional methods, and b) reduce generation scarcity events and consequently improve reliability by increasing flexibility requirements at times when unconditional forecast-based requirements understate actual ramp uncertainty. In addition to the products just described (quantification of solar uncertainty, its translation into requirements for ramp capability product, and quantification of the benefits of more accurate ramp requirements), this project also developed a visualization system that alerts system operators of ramp and uncertainty conditions within the network based on solar forecasts. The system is called Resource Forecast and Ramp Visualization for Situational Awareness (RaVIS). These four products represent significant advances in the state-of-the-art of probabilistic solar forecasting, development of weather-informed reserve requirements, production costing methods for estimating the benefits of more accurate reserve requirements, and visualization of system status, respectively. Yet the products are also practical and can be immediately implemented, potentially enabling system operators to save millions of dollars in ramp product procurement costs per year.

14 SOLAR ENERGY↗

A review of materials used in tomographic volumetric additive manufacturing

Abstract Volumetric additive manufacturing is a novel fabrication method allowing rapid, freeform, layer-less 3D printing. Analogous to computer tomography (CT), the method projects dynamic light patterns into a rotating vat of photosensitive resin. These light patterns build up a three-dimensional energy dose within the photosensitive resin, solidifying the volume of the desired object within seconds. Departing from established sequential fabrication methods like stereolithography or digital light printing, volumetric additive manufacturing offers new opportunities for the materials that can be used for printing. These include viscous acrylates and elastomers, epoxies (and orthogonal epoxy-acrylate formulations with spatially controlled stiffness) formulations, tunable stiffness thiol-enes and shape memory foams, polymer derived ceramics, silica-nanocomposite based glass, and gelatin-based hydrogels for cell-laden biofabrication. Here we review these materials, highlight the challenges to adapt them to volumetric additive manufacturing, and discuss the perspectives they present. Graphical abstract

36 MATERIALS SCIENCE↗

A Three-Dimensional Level Set Simulation of Coupled Reactive Transport and Precipitation/Dissolution

Direct simulation of reactive transport in porous media is challenging due to the difficulty of tracking the dynamics of evolving solid-fluid interfaces. To meet this challenge, a level set method for capturing interface evolution due to dissolution and/or precipitation has been integrated into the standard grid-based finite-difference approach for simulating flow and transport in complex geometries. Based on the level set description of the interface geometry, Chorin’s projection method was modified to approximately satisfy the nonslip boundary condition at the grain surface, and a sharp interface methodwas developed for calculating the concentration field near the grain surface in the presence of surface reaction. Compared with the pixel representations of the interface used in other methods, the sub-grid representation using level set method offers significantly improved accuracy and efficiency. The advantage of the method is demonstrated in a systematic investigation of precipitation/dissolution in a simple three dimensional pore-throat with varying throat apertures. The simulation was first validated in a grid-refinement study. The effects of flow conditions, reaction rates and three-dimensional geometries are explored both qualitatively and quantitatively. The permeability-porosity relationship calculated from simulations is compared with Carman-Kozeny constitutive models to illustrate the limited capability of these empirical models, which are based on simplified pore-scale geometries and conditions.

58 GEOSCIENCES↗

Random projection using random quantum circuits

The random sampling task performed by Google's Sycamore processor gave us a glimpse of the “quantum supremacy era.” This has definitely shed some light on the power of random quantum circuits in this abstract task of sampling outputs from the (pseudo)random circuits. In this paper, we explore a practical near-term use of local random quantum circuits in dimensional reduction of large low-rank data sets. We make use of the well-studied dimensionality reduction technique called the random projection method. This method has been extensively used in various applications such as image processing, logistic regression, entropy computation of low-rank matrices, etc. We prove that the matrix representations of local random quantum circuits with sufficiently shorter depths [ ∼ O ( n ) ] serve as good candidates for random projection. We demonstrate numerically that their projection abilities are not far off from the computationally expensive classical principal components analysis on MNIST and CIFAR-100 image datasets. We also benchmark the performance of quantum random projection against the commonly used classical random projection in the tasks of dimensionality reduction of image data sets and computing von Neumann entropies of large low-rank density matrices. And finally, using variational quantum singular value decomposition, we demonstrate a near-term implementation of extracting the singular vectors with dominant singular values after quantum random projecting a large low-rank matrix to lower dimensions. All such numerical experiments unequivocally demonstrate the ability of local random circuits to randomize a large Hilbert space at sufficiently shorter depths with robust retention of properties of large data sets in reduced dimensions. Published by the American Physical Society 2024

Kumaran, Keerthi (ORCID:0009000949125721)↗