Search NASA⌕ Search

SEARCH · Search NASA

Results for “pulling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Stabilizing Silicon-Ribbon Growth At Early Stages

Device mechanically stabilizes buttons from which silicon ribbons grown by dendritic-web process. Eliminates tendency for button to tip and interrupt pull because of asymmetry. Silicon seed hangs from holder through stabilizing tube. While button growing, tube elevated above melt surface. When ready for pulling of ribbon, tube comes to rest on button and prevents tipping. Large button used. Even if button assumes highly-asymmetrical weight distrubtion in early stages of growth, little danger of tipping and breakage of nascent ribbon.

Henry, Paul K.↗
NASA NTRS1987

Using bibliographic databases in technology transfer

When technology developed for a specific purpose is used in another application, the process is called technology transfer--the application of an existing technology to a new use or user for purposes other than those for which the technology was originally intended. Using Bibliographical Databases in Technology Transfer deals with demand-pull transfer, technology transfer that arises from need recognition, and is a guide for conducting demand-pull technology transfer studies. It can be used by a researcher as a self-teaching manual or by an instructor as a classroom text. A major problem of technology transfer is finding applicable technology to transfer. Described in detail is the solution to this problem, the use of computerized, bibliographic databases, which currently contain virtually all documented technology of the past 15 years. A general framework for locating technology is described. NASA technology organizations and private technology transfer firms are listed for consultation.

Huffman, G. David↗
NASA NTRS1988

Development of a torsion balance for adhesion measurements

A new torsion balance for study of adhesion in ceramics is discussed. A torsion wire and a linear variable differential transformer are used to monitor load and to measure pull-off force (adhesion force). The investigation suggests that this torsion balance is valuable in studying the interfacial properties of ceramics in controlled environments such as in ultrahigh vacuum. The pull-off forces measured in dry, moist, and saturated nitrogen atmosphere demonstrate that the adhesion of silicon nitride contacts remains low at humidities below 80 percent but rises rapidly above that. The adhesion at saturation is 10 times or more greater than that below 80 percent relative humidity. The adhesion in a saturated atmosphere arises primarily from the surface tension effects of a thin film of water adsorbed on the surface. The surface tension of the water film was 58 x 10 to the minus 5 to 65 x 10 to the minus 5 power. The accepted value for water is 72.7 x 10 to the minus 5 power N/cm. Adhesion characteristics of silicon nitride in contact with metals, like the friction characteristics of silicon carbide to metal contacts, can be related to the relative chemical activity of metals in ultrahigh vacuum. The more active the metal, the higher the adhesion.

Miyoshi, Kazuhisa↗
NASA NTRS1988

Linear force device

The object of the invention is to provide a mechanical force actuator which is lightweight and manipulatable and utilizes linear motion for push or pull forces while maintaining a constant overall length. The mechanical force producing mechanism comprises a linear actuator mechanism and a linear motion shaft mounted parallel to one another. The linear motion shaft is connected to a stationary or fixed housing and to a movable housing where the movable housing is mechanically actuated through actuator mechanism by either manual means or motor means. The housings are adapted to releasably receive a variety of jaw or pulling elements adapted for clamping or prying action. The stationary housing is adapted to be pivotally mounted to permit an angular position of the housing to allow the tool to adapt to skewed interfaces. The actuator mechanisms is operated by a gear train to obtain linear motion of the actuator mechanism.

Clancy, John P.↗
NASA NTRS1989

Vacuum Head Checks Foam/Substrate Bonds

Electromechanical inspection system quickly gives measurements indicating adhesion, or lack thereof, between rigid polyurethane foam and aluminum substrate. Does not damage inspected article, easy to operate, and used to perform "go/no-go" evaluations or as supplement to conventional destructive pull-plug testing. Applies vacuum to small area of foam panel and measures distance through which foam pulled into vacuum. Probe head applied to specimen and evacuated through hose to controller/monitor unit. Digital voltmeter in unit reads deflection of LVDT probe head.

Lloyd, James F.↗
NASA NTRS1990

M-52 spray booth qualification test

The procedures, performance, and results obtained from the M-52 spray booth qualification test are documented. The test was conducted at Thiokol Corporation, Space Operations, M-52 Inert Parts Preparation facility. The purpose of this testing sequence was to ensure the spray booth would produce flight qualified hardware. The testing sequence was conducted in two series. The first series was conducted under CTP-0142, Revision 1. The second series was conducted in accordance with CTP-0142, Revision 2. The test sequence started with CTP-0142, Revision 1. The series consisted of the contamination removal test and the performance test. The contamination removal test was used to assess the Teflon level in the spray booth. The performance test consisted of painting and Chemloking a forward dome inside the spray booth per flight procedures. During the performance test, two sets of witness panels (case/insulation and steel/epoxy/steel) were prepared and pull tested. The CTP-0142, Revision 2, series of testing consisted of re-testing the steel/epoxy/steel witness panels. The pull tests analysis indicates the results of the tensile tests were comparable to the systems tunnel witness panel database. The exposed panel set and the control panel set average tensile values were above the 1-basis lower limits established on the systems tunnel witness panel database. It is recommended that the M-52 spray booth be qualified for producing flight hardware.

Source record↗
NASA NTRS1990

The status of cesium beam frequency standards

There has been a lot of progress in cesium beam frequency standards in the last few years some of which will be reported here. Optical pumping is being pursued actively in a number of laboratories. Optically slowed and cooled beams have been demonstrated as well as traps for cold neutral atoms. The microwave cavity performance with regard to local phase shift at the beam holes was improved by use of carefully designed and built ring structures for the cavity ends. Work is being done on improvements in electronics with some emphasis on use of digital circuitry and microprocessors. The frequency pulling due to microwave Delta M = +/- 1 transitions (Ramsey pulling) was analyzed and shown to be important. Status of cesium beam frequency standards in some of the laboratories as well as some of the commercial work is discussed. Optical pumping and detection are discussed.

Cutler, Leonard S.↗
NASA NTRS1991

Space platform power system hardware testbed

The scope of the work on the NASA Space Platform includes the design of a multi-module, multi-phase boost regulator, and a voltage-fed, push-pull autotransformer converter for the battery discharger. A buck converter was designed for the charge regulator. Also included is the associated mode control electronics for the charger and discharger, as well as continued development of a comprehensive modeling and simulation tool for the system. The design of the multi-module boost converter is discussed for use as a battery discharger. An alternative battery discharger design is discussed using a voltage-fed, push-pull autotransformer converter. The design of the charge regulator is explained using a simple buck converter. The design of the mode controller and effects of locating the bus filter capacitor bank 20 feet away from the power ORU are discussed. A brief discussion of some alternative topologies for battery charging and discharging is included. The power system modeling is described.

Sable, D.↗
NASA NTRS1991

An analysis of the wear behavior of SiC whisker reinforced alumina from 25 to 1200 C

A model is described for predicting the wear behavior of whisker reinforced ceramics. The model was successfully applied to a silicon carbide whisker reinforced alumina ceramic composite subjected to sliding contact. The model compares the friction forces on the whiskers due to sliding, which act to pull or push them out of the matrix, to the clamping or compressive forces on the whiskers due to the matrix, which act to hold the whiskers in the composite. At low temperatures, the whiskers are held strongly in the matrix and are fractured into pieces during the wear process along with the matrix. At elevated temperatures differential thermal expansion between the whiskers and matrix can cause loosening of the whiskers and lead to pullout during the wear process and to higher wear. The model, which represents the combination of elastic stress analysis and a friction heating analysis, predicts a transition temperature at which the strength of the whiskers equals the clamping force holding them in the matrix. Above the transition the whiskers are pulled out of the matrix during sliding, and below the transition the whiskers are simply fractured. The existence of the transition gives rise to a dual wear mode or mechanism behavior for this material which was observed in laboratory experiments. The results from this model correlate well with experimentally observed behavior indicating that the model may be useful in obtaining a better understanding of material behavior and in making material improvements.

Dellacorte, Christopher↗
NASA NTRS1991

Evaluation of Surlyn 8920 as PHE Visor Material and Evaluations of New Adhesives for Improving Bonding Between Teflon and Stainless Steel at Cryogenic Temperature

Two studies are presented, and in the first study, Surlyn 8920 (an ionic and amorphous low density polyethylene made by Dupont) was evaluated as a possible replacement of Plexyglass G as PHE visor material. Four formulations of the polymer were made by adding different amounts of UV stabilizer, energy quencher, and antioxident in a Brabender Plasticorder. The formulated polymers were molded in the form of sheets in a compression molder. Cut samples from the molded sheets were exposed in a weatherometer and tested on Instron Tensile Tester for strength and elongation. Specially molded samples of the formulated polymers were subjected to Charpy Impact Tests. In the second study, preliminary evaluations of adhesives for improvement of bonding between Teflon and stainless steel (SS) were performed. Kapton, a high temperature polyimide made by Dupont, and a rubber based adhesive made by Potter Paint Co., were evaluated against industrial quality epoxy, the current material used to bond Teflon and SS. The degreased surfaces of the SS discs were etched mechanically, with a few of these etched chemically. The surfaces of the SS discs were etched mechanically, with a few of these etched chemically. Bonding strengths were evaluated using lap shear tests on the Instron Tensile Tester for the samples bonded by Kapton and industrial quality epoxy. Bond strengths were also evaluated using a pull test on the Instron for the samples bonded by Potter adhesive (CWL-152) and industrial quality epoxy. Based on limited lap shear data, Kapton gave bond strength favorable compared to that of industrial epoxy. Based on limited pull test data, Kapton bonded and CWL-152 bonded samples showed poor strength compared to epoxy bonded sample.

Ray, Asit K.↗
NASA NTRS1991

Composite superconducting wires obtained by high-rate tinning in molten Bi-Pb-Sr-Ca-Cu-O system

Long lengths of metal superconductor composites were prepared by passing a copper wire through the bismuth based molten oxide system at a constant speed. The key to successful composite preparation is the high pulling speed involved, which permits minimization of the severe interaction between the unbuffered metal surface and the oxide melt. Depending on the temperature of the melt and the pulling speed, a coating with different thickness and microstructure appeared. The nonannealed thick coatings contained a Bi2(Sr,Ca)2Cu1O6 phase as a major component. After relatively short time annealing at 800 C, both resistivity and initial magnetization versus temperature measurements show superconducting transitions beginning in the 110 to 115 K region. The effects of annealing and composition on obtained results are discussed. This method of manufacture led to the fabrication of wire with a copper core in a dense covering with uniform thickness of about h approximately equal to 5 to 50 microns. Composite wires with h approximately equal to 10 microns (h/d approximately equal to 0.1) sustained bending on a 15 mm radius frame without cracking during flexing.

Grosav, A. D.↗
NASA NTRS1990

Performance evaluation of a mobile satellite system modem using an ALE method

Experimental performance of a newly designed demodulation concept is presented. This concept applies an Adaptive Line Enhancer (ALE) to a carrier recovery circuit, which makes pull-in time significantly shorter in noisy and large carrier offset conditions. This new demodulation concept was actually developed as an INMARSAT standard-C modem, and was evaluated. On a performance evaluation, 50 symbol pull-in time is confirmed under 4 dB Eb/No condition.

Ohsawa, Tomoki↗
NASA NTRS1992

Effect of fiber orientation on the fracture toughness of brittle matrix composites

The effective fracture toughness of brittle matrix materials can be increased through the addition of short, poorly bonded fibers which bridge the growing crack. The orientation distribution of the fibers is likely to be biased, and not in an ideal random or aligned state. A micromechanical model is formulated for the postcracking behavior using the force-displacement relation for an arbitrary fiber bridging a crack, the fiber orientation density function, and the fiber location density function. This model is then used to determine an effective traction law for the bridging fibers, as well as the steady state bridging toughness increment. In most cases, the results may be placed in the form of a product of the aligned fiber results times a modifying integrated orientation factor. The frictional shear stress on fiber pull-out is allowed to vary during pull-out, modeling the effects of matrix breakdown, fiber surface smoothing or wear debris accumulation. Results are presented for a variety of representative planar and three-dimensional fiber orientation states.

Jain, L. K.↗
NASA NTRS1992

Stress observations and driving force models for the South American plate

A comparison of stress observations to predictions of driving force models for the South American plate is presented. Conditions for dynamical equilibrium are used to estimate the magnitudes of forces as a function of age, with ridge push and slab pull as active forces, and plate drag and slab resistance as passive forces. The results are consistent with earlier published models, and it is found that the primary balance for an oceanic plate is between slab pull and the resisting drag forces. The model is generalized for the possible forces driving the South American plate, and it is compared with observed stress measurements and kinematics. The plate balance is found to be largely between ridge push and plate drag. The magnitude of a possible trench suction force is estimated using a model with an eddy between the Nazca slab and the overlying South American plate.

Stefanick, Michael↗
NASA NTRS1992

Preliminary results from three USML-1 Glovebox experiments

Three simple experiments, namely, Marangoni convection in closed containers (MCCC), fiber pulling in microgravity, and stability of a double float zone are described which were conducted during the U.S. Microgravity Laboratory mission (USML) in July 1992. Results show that, in the MCCC experiment, there was no evidence of partial wetting between the liquid and the walls either in the wetting or nonwetting configuration. In the nonwetting system, the void formed a hemispherical bubble that remained pinned to the walls with considerable contact line resistance. Significant differences were observed in the ability to pull liquid strings in low gravity in those materials which readily form liquid strands in normal gravity and do not necessarily form strands in reduced gravity. The double float zone configuration appeared to be quite stable in both cylindrical and sheet form.

Naumann, Robert J.↗
NASA NTRS1992

Evolution of attached and detached slabs and their associated mantle dynamics

Over the two years of the NASA grant, this project has produced a significant amount of research results related to the plate subduction process and the surface crustal deformation at convergent boundaries (i.e., above subduction zones). While some research objectives are completely accomplished, other research tasks remain active and continue to be investigated at present. A steady state analytic thermal model for subducting slabs was used to examine the torques acting on a descending slab. It is found that gravitational torque vanishes when a slab is dipping either vertically or horizontally, unlike previous studies indicating that the magnitude of gravitational torque decreases as dip angle increases. Subsequently, a new time-dependent, analytic thermal model for a subducting slab was developed. The new model enables us to study transient phenomena associated with plate subduction analytically. On the basis of this model, the nature of slab dip angles was evaluated. Slab dip angles are found to be transient features. As they penetrate into the mantle and increase their lengths, the associated gravitational torque also increases resulting in a downward pulling of the slab to the steeper dip angle. This is especially true once a slab penetrates the olivine-spinel phase boundary at about 400 km depth. However, if the phase transformation does not follow the equilibrium condition, the gravitational torque may have a different behavior. This problem was investigated. Except for fast descending slabs, non-equilibrium phase transformation can only slow down the transient increase of slab dip angles discussed earlier. Its effect is not sufficiently strong to reverse the downward pulling for most of the slabs. However, when slabs subducting at 10 cm/yr or faster, a sufficient amount of metastable olivine can exist beneath 400 km. Because of its low density compared with the surrounding spinel, an upward buoyancy is produced resulting in an upward bending of the slab and possibly an upward rotation of the slab such that smaller dip angles are formed. Seismic studies of the Japanese Slab seem to support this interpretation. The development of oroclinal geometries at convergent boundaries was also examined to study plate obduction which is an important ingredient to the initiation of plate subduction. Although the study suggests that surface features are better modeled by block models, the large scale deformation can be adequately studied by viscous models. Such a model is now under development to complete our original objective to study the initiation of plate subduction. Finally, a three-dimensional, finite element, spherical convective model is developed to study dynamic plate subductions. The model development is now complete and it is being tested to ensure its proper operation. The model is able to generate convection results with a viscosity contrast of about 100. Our research continues to push the viscosity contrast to a level that is appropriate for a subducting slab.

Hsui, Albert T.↗
NASA NTRS1993

An analysis of the wear behavior of SiC whisker-reinforced alumina from 25 to 1200 C

A model is described for predicting the wear behavior of whisker reinforced ceramics. The model was successfully applied to a silicon carbide whisker reinforced alumina ceramic composite subjected to sliding contact. The model compares the friction forces on the whiskers due to sliding, which act to pull or push them out of the matrix, to the clamping or compressive forces on the whiskers due to the matrix, which act to hold the whiskers in the composite. At low temperatures, the whiskers are held strongly in the matrix and are fractured into pieces during the wear process along with the matrix. At elevated temperatures differential thermal expansion between the whiskers and matrix can cause loosening of the whiskers and lead to pullout during the wear process and to higher wear. The model, which represents the combination of elastic stress analysis and a friction heating analysis, predicts a transition temperature at which the strength of the whiskers equals the clamping force holding them in the matrix. Above the transition the whiskers are pulled out of the matrix during sliding, and below the transition the whiskers are simply fractured. The existence of the transition gives rise to a dual wear mode or mechanism behavior for this material which was observed in laboratory experiments. The results from this model correlate well with experimentally observed behavior indicating that the model may be useful in obtaining a better understanding of material behavior and in making material improvements.

Dellacorte, Christopher↗
NASA NTRS1938

Flight and Wind-tunnel Tests of an XBM-1 Dive Bomber

Results are given of pressure-distribution measurements made in flight over the right wing cellule and the right half of the horizontal tail surfaces of a dive-bombing biplane. Simultaneous measurements were also taken of the air speed, control-surface positions, control forces, and normal accelerations during various abrupt maneuvers in vertical plane. These maneuvers consisted of push-downs and pull-ups from level flight, dives and dive pull-ups from inverted flight. Besides the pressure measurements, flight tests were made to obtain (1) wing-fabric deflections during dives and (2) variation of the minimum drag coefficient with Reynolds Number. Supplementary tests were also done in the full-scale wind tunnel to obtain the characteristics of the airplane under various propeller conditions and with various tail settings. The results indicate that: (1) by increasing the fabric deflection between pressure ribs, the span load distribution was considerably modified near the center and the wing moment relations were changed; and (2) the minimum drag was less for the idling propeller than for the propeller locked in a vertical position. The value of C(sub D sub min) was equal to K(Reynolds Number)(exp -0.03) for a range from 2,800,000 to 13,100,000.

Donely, Philip↗