Search NASA⌕ Search

SEARCH · Search NASA

Results for “reverse rates”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Laser velocimeter measurements in shrouded and unshrouded radial flow pump impellers

Shrouded and unshrouded versions of a four-vaned radial flow impeller with a design flow coefficient of 0.063 were tested in a volute pump using a two-component frequency-shifted laser velocimeter. Velocity profiles were measured at six flow rates and at four radial and six circumferential positions in the volute. The variations of the velocity from blade to blade and in the axial direction were measured and are presented. A passage vortex caused by tip leakage and relative casing wall velocity was found in the unshrouded impeller. The tip leakage did not accumulate in the suction wake region; the suction wake region was only 30 to 50 percent as large in the unshrouded impeller as compared to the shrouded impeller. The slip was 30 percent higher in the unshrouded impeller and the variation of slip with flow rate is presented. At no measured position in the impellers did the slip factor reach unity; the closest approach was 0.90. Reverse loadings of the vanes at outer radii were found for flow rates below the impeller/volute matching point for both impellers.

Hamkins, C. P.↗
NASA NTRS1973

Principal sources and dispersal patterns of suspended particulate matter in nearshore surface waters of the northeast Pacific Ocean

The author has identified the following significant results. Release-recovery paths of drift cards released in conjunction with ERTS-1 overflight show that nearshore surface currents along the central and northern California coast flowed southward at an average rate in excess of 10 cm/sec (8.5 km/day) during August and September 1973 (California Current). By the middle of October 1973, the nearshore surface currents had reversed and the dominant flow velocity was northward at an average rate in excess of 20 cm/sec (17 km/ day) (Davidson Current). The August-September data suggested the presence of counterclockwise gyres in Monterey Bay and the Gulf of the Farallones, but by the middle of October, the gyres were no longer evident. Imagery of April 1973 showed well developed plumes of suspended sediment in Monterey Bay from the Salinas River and in the Gulf of the Farallones from San Francisco Bay. ERTS-1 imagery provides an effective means of monitoring timber harvest in the redwood forest along the northern California coast. ERTS-1 imagery also clearly portrays contrasting topographic belts characterized by fluvial erosion and by mass movement. The most visually apparent and most persistent river mouth suspended sediment plumes are associated with those rivers that drain belts of topography that appear to have been eroded primarily by mass movement.

Carlson, P. R.↗
NASA NTRS2019

On the Coronal Mass Ejection Detection Rate during Solar Cycles 23 and 24

The Solar and Heliospheric Observatory (SOHO) mission's white light coronagraphs have observed more than25,000 coronal mass ejections (CMEs) from 1996 January to the end of 2015 July. This period of time covers almost two solar cycles (23 and 24). The basic attributes of CMEs, reported in the SOHO/Large Angle and Spectrometric Coronagraph (LASCO) catalog, during these solar cycles were statistically analyzed. The question of the CME detection rate and its connection to the solar cycles was considered in detail. Based on the properties and detection rate, CMEs can be divided into two categories: regular and specific events. The regular events are pronounced and follow the pattern of sunspot number. On the other hand, the special events are poorer and more correlated with the general conditions of heliosphere and corona. Nevertheless, both groups of CMEs are the result of the same physical phenomenon, viz. release of magnetic energy from closed field regions. It was demonstrated that the enhanced CME rate, since the solar cycle 23 polar-field reversal, is due to a significant decrease of total(magnetic and plasma) heliospheric pressure as well as the changed magnetic pattern of solar corona. CMEs expel free magnetic energy and helicity from the Sun; therefore, they are related to complex solar magnetic field structure. It is also worth emphasizing that the CMEs listed in the SOHO/LASCO catalog are real ejections (not false identification). Their detection rate reflects the global evolution of the magnetic field on the Sun, and not only changes in the magnetic structures associated with sunspots.

Michalek, Grzegorz↗
DOE OSTI2021

Air separation via two-step solar thermochemical cycles based on SrFeO 3-δ and (Ba,La) 0.15 Sr 0.85 FeO 3-δ perovskite reduction/oxidation reactions to produce N 2 : rate limiting mechanism(s) determination

Two-step solar thermochemical cycles based on reversible reactions of SrFeO 3–δ and (Ba,La) 0.15 Sr 0.85 FeO 3–δ perovskites were considered for air separation. The cycle steps encompass (1) the thermal reduction of SrFeO 3–δ or (Ba,La) 0.15 Sr 0.85 FeO 3–δ perovskites driven by concentrated solar irradiation and (2) oxidation in air to remove O 2 and produce N 2 . Rate limiting mechanisms were examined for both reactions using a combination of isothermal and non-isothermal thermogravimetry for temperature-swings between 673 and 1373 K, heating rates of 10, 20, and 50 K min –1 , and O 2 pressure-swings between 20% O 2 /Ar and 100% Ar at atmospheric pressure. Evolved O 2 and associated lag due to transport behavior were measured with gas chromatography and used with measured sample temperatures to predict equilibrium compositions from a compound energy formalism thermodynamic model. Measured and predicted chemical equilibrium changes in deviation from stoichiometry were compared. Rapid chemical kinetics were observed as the samples equilibrated rapidly for all conditions, indicative that heat and mass transfer were the rate limiting mechanisms. Furthermore, the effects of bulk diffusion (or gas diffusion through the bed or pellet) were examined using pelletized and loose powdered samples and determined to have no discernable impact.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

On the Nature of Field-Enhanced Water Dissociation in Bipolar Membranes

Bipolar membranes (BPMs) possess the potential to optimize pH environments for electrochemical synthesis applications when employed in reverse bias. Unfortunately, the performance of BPMs in reverse bias has long been limited by the rate of water dissociation (WD) occurring at the interface of the BPM. Herein, we develop a continuum model of the BPM that agrees with experiment to understand and enhance WD catalyst performance by considering multiple kinetic pathways for WD in the BPM junction catalyst layer. Here, the model reveals that WD catalysts with a more highly alkaline or acidic pH at the point of zero charge (pH PZC ) exhibit accelerated WD kinetics because the more acidic or alkaline pH PZC catalysts possess greater surface charge, enhancing the local electric field and rate of WD. The model is then employed to explore the sensitivity of the BPM performance to various BPM physical parameters. Finally, the model is used to simulate the operation of bimetallic WD catalysts, demonstrating that an optimal bimetallic catalyst has an acidic pH PZC catalyst matched with the cation-exchange layer and an alkaline pH PZC catalyst matched with the anion-exchange layer. The study provides insight into the operation of BPM WD catalysts and gives direction toward the development of next-generation WD catalysts for optimal BPM performance under water-splitting and related conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Calcium Cosalt Addition to Alter the Cation Solvation Structure and Enhance the Ca Metal Anode Performance

Accessing the energy density and sustainability of calcium metal batteries requires mastering reversible calcium electrodeposition through electrolyte design. Several electrolytes support reversible, ambient temperature deposition but at utilization and rate too low for practical applications. These challenges stem from solvation structures characterized by either high barriers for cation desolvation or thermodynamic instability, leading to parasitic decomposition of the salt and solvent. The optimal solvation structure for the effective delivery of calcium to the electrode interface is not known. In this work, we show that adding a relatively small amount of a weakly associating calcium salt (calcium carba-closo-dodecaborate) to an otherwise strongly associated solution (calcium borohydride in tetrahydrofuran) produces a surprising population of fully solvent-coordinated Ca2+ cations in the form of solvent-separated ion pairs (SSIPs). We further demonstrate that the formation of these SSIPs beneficially impacts the kinetics and thermodynamics of calcium electrodeposition, revealing the unexpected finding that direct coordination of Ca2+ by the BH4– anion limits the electrodeposition process. These findings reveal how the competition between solvent and anion coordination to Ca2+ affects calcium deposition kinetics and cycling stability, setting the stage for a new calcium electrolyte design based on mixed anion electrolytes.

Landers, Alan T.↗
DOE OSTI2024

Synthesizing Highly Crystalline Graphite Powder from Bulk Polyethylene Waste for Lithium-Ion Battery Anodes

Upcycling plastic waste into graphite can potentially be used, in conjunction with other methods, to manage existing waste materials and diversify graphite supply chains. However, synthesizing large quantities of crystalline graphite powder from plastic waste, particularly polyethylene (PE), remains a challenge because PE decomposes into light gases during thermal processing and simple methods do not exist at any appreciable size scale to address this challenge. In this work, a method is developed for air processing bulk forms of PE waste to create stable carbon char that does not readily decompose during high-temperature processing. This method employs solid additives in the form of salts, which are combined with the PE melt during air processing to increase the effective surface area of the melt and improve the oxygen-driven chemistry that stabilizes PE for high-temperature processing. After removal of the solid salt additives from the PE-derived char, it is converted into a highly crystalline bulk graphite powder using an Fe-based catalytic process. The PE-derived graphite anode in a lithium-ion coin cell showed a specific capacity of 345 mAh/g at 0.05C with an initial Coulombic efficiency of 87% and reversible capacity retention of ~100% at different current rates. It also showed a specific capacity of up to 313 mAh/g at 0.5 discharge/charge cycles per hour (0.5C) and Coulombic efficiency of 99.9% after 250 cycles, indicating excellent electrochemical performance as an anode material for lithium-ion batteries. This method illustrates that there are opportunities for upcycling large quantities of PE waste to produce graphite powders suitable for use in LIBs.

25 ENERGY STORAGE↗
NASA NTRS1983

Magnus effects on spinning transonic missiles

Magnus forces and moments were measured on a basic-finner model spinning in transonic flow. Spin was induced by canted fins or by full-span or semi-span, outboard and inboard roll controls. Magnus force and moment reversals were caused by Mach number, reduced spin rate, and angle of attack variations. Magnus center of pressure was found to be independent of the angle of attack but varied with the Mach number and model configuration or reduced spin rate.

Seginer, A.↗
NASA NTRS1988

On the cyclic stress-strain behaviour of a Ni-base superalloy at room temperature

The cyclic stress-strain behavior of Nimonic alloy PE16 was studied at room temperature and at different aging conditions to determine whether the plateau in the cyclic stress-strain curve (CSSC) reported by Arbuthnot (1982) is typical of the room temperature behavior and/or some specific initial microstructural states. Specimen blanks were heat-treated in batches in Ar/H2 (98/2) atmosphere to produce gamma-prime precipitates of different average sizes, but with the volume fraction of gamma-prime precipitates kept constant at about 7 percent at all the heat-treatment conditions. Total axial strain controlled LCF tests were conducted under fully reversed loading (R = -1) at a constant strain rate of 0.004/s, using a servohydraulic machine. The load response in tension and compression was recorded continually, and stress-strain hysteresis loops were recorded at frequent intervals. In the present investigation, the CSSCs of the P16 alloy at room temperature did not display the plateaus reported by Arbuthnot.

Singh, Vakil↗
NASA NTRSDate not supplied

Dissociative Recombination (DR) and Associative Ionization (AI) Cross Section Calculations for the NO+ + e yields N + O (2D+3P, 2P+3P, and 2D+1D) Reaction for Atmospheric Entry Modeling

During entry of a space craft into Earth atmosphere, the flow surrounding the vehicle becomes partially ionized leading to significant cation and free-electron production. Subsequently, electron impact excitation and dissociation form radiating excited state species that contribute to the heat load on the vehicle. While experimental data on selected total cross sections are available, few experiments address the need for accurate AI cross sections for metastable atomic states at the high temperatures realized in atmospheric re-entry. In order to maintain desired safety margins during atmospheric entry of a space vehicle, chemical reaction models need to accurately account for this process. For the present study, we have computed vibrationally resolved cross sections for the DR of NO+ for electron energies between 0.01 to 10 eV and apply microscopic reversibility to obtain the AI cross sections and rate coefficients. For the DR cross section calculations, we use state-of-the-art MRCI potential energy curves. The resulting adiabatic potential curves are transformed to a diabatic representation, which is used in time-dependent wave packet calculations to describe the nuclear motion of the dissociating cation upon collision with an electron. Based on the wave function evolution in time, these calculations provide T-matrix and cross sections for the DR including recombination into the low energy metastable atomic states. The DR and AI rate coefficients are compared with the available experimental data.

Ewa Papajak↗
DOE OSTI2020

Improved lithium storage capacity and high rate capability of nitrogen-doped graphite-like electrode materials prepared from thermal pyrolysis of graphene quantum dots

Adopting a solid-phase microwave-assisted technique followed by thermal pyrolysis of N-functionalized graphene quantum dots, novel nitrogen-doped graphite-like (NGL) electrode materials were synthesized in this work and served as the anode for Li-ion batteries. The NGL anode demonstrated reversible capacity of 530 mAh g -1 at 0.1C, superior rate capability at high C rate operation (420 mAh g -1 at 5C), remarkable initial coulombic efficiency (>95.7%), and excellent cyclic stability along with high efficiency (>99.1%) during entire cycling. The NGL anode nanostructure enables improved lithium ion mobility and reversible Li + storage during cycling. The analysis of the Ragone plots revealed that the specific energy of NGL anode reaches to ca. 840 Wh kg -1 at the power density of 4200 W kg -1 . The diffusion coefficient of Li ions was measured as 1.69 × 10 -9 cm 2 s -1 for the NGL anode material, substantially improving over commonly used graphite electrodes (15–26 times higher Li + diffusivity). The high-rate cyclability as well as the cyclic stability of the NGL anodes were also confirmed via long-term cycling of full pouch cells assembled with ternary cathode and NGL anode. The robust design of the NGL anode materials introduced in this work, paves the way for designing next-generation lithium-ion batteries operating at ultra-high C rates.

25 ENERGY STORAGE↗
NASA NTRS1991

Effect of ohmic, mass-transfer, and kinetic resistances on linear-sweep voltammetry in a cylindrical-pore electrode

A means is presented to account for the effect of ohmic, mass-transfer, and kinetic resistances on linear-sweep voltammograms by modeling a pore in a porous matrix as a cylindrical-pore electrode, and solving the mass and charge conservation equations in the context of this geometry for the simply redox reaction O + ne(-) yield R where both O and R are soluble species. Both analytical and numerical techniques are used to solve the governing equations. The calculated peak currents and potentials are correlated by empirical formulas to the measurable parameters: sweep rate, concentration of the redox species, diffusion coefficient, conductivity of the electrolyte, and pore dimensions. Using the correlations, a methodology is established for determining if the redox reaction kinetics are irreversible or reversible (Nernstian). If the reaction is irreversible, it is shown how the standard rate constant and the transfer coefficient may be extracted from linear-sweep voltammetry data, or, if the reaction is reversible, how the number of electrons transferred may be deduced.

Weidner, John W.↗
DOE OSTI2024

Target–decoy false discovery rate estimation using Crema

Assigning statistical confidence estimates to discoveries produced by a tandem mass spectrometry proteomics experiment is critical to enabling principled interpretation of the results and assessing the cost/benefit ratio of experimental follow-up. The most common technique for computing such estimates is to use target-decoy competition (TDC), in which observed spectra are searched against a database of real (target) peptides and a database of shuffled or reversed (decoy) peptides. TDC procedures for estimating the false discovery rate (FDR) at a given score threshold have been developed for application at the level of spectra, peptides, or proteins. Although these techniques are relatively straightforward to implement, it is common in the literature to skip over the implementation details or even to make mistakes in how the TDC procedures are applied in practice. Here we present Crema, an open-source Python tool that implements several TDC methods of spectrum-, peptide- and protein-level FDR estimation. Crema is compatible with a variety of existing database search tools and provides a straightforward way to obtain robust FDR estimates.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Engineering a disulfide-gated switch in streptavidin enables reversible binding without sacrificing binding affinity

Although high affinity binding between streptavidin and biotin is widely exploited, the accompanying low rate of dissociation prevents its use in many applications where rapid ligand release is also required. To combine extremely tight and reversible binding, we have introduced disulfide bonds into opposite sides of a flexible loop critical for biotin binding, creating streptavidin muteins (M88 and M112) with novel disulfide-switchable binding properties. Crystal structures reveal how each disulfide exerts opposing effects on structure and function. Whereas the disulfide in M112 disrupts the closed conformation to increase k off , the disulfide in M88 stabilizes the closed conformation, decreasing k off 260-fold relative to streptavidin. The simple and efficient reduction of this disulfide increases k off 19,000-fold, thus creating a reversible redox-dependent switch with 70-fold faster dissociation kinetics than streptavidin. The facile control of disulfide formation in M88 will enable the development of many new applications requiring high affinity and reversible binding.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Thermodynamics of signal transduction systems and fluctuation theorem in a signal cascade

Biochemical chain reactions are signal transduction cascades that can transmit biological information about the intracellular environment. In this study, we modelled a chain reaction as a code string for applying information theory. Herein, we assumed that cell signal transduction selects a strategy to maximize the transduced signal per signal event duration. To investigate the same, we calculated the information transmission capacity of the reaction chain by maximizing the average entropy production rate per reaction time, indicating the idea of the entropy coding method. Moreover, we defined a signal cascade trajectory. Subsequently, we found that the logarithm of the forward and reverse transition ratio per reaction time is equal to the entropy production rate, which derives the form of the fluctuation theorem in signal transduction. Our findings suggest the application of information entropy theory for analysing signal transduction.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS2013

Design Safety Used in NASA's Human-rated Primary Lithium Batteries

Single cell tests were benign for external short, inadvertent charge and overdischarge into reversal up to 4.5 A. At lower current loads cells die (may be due to excessive dendrite formation) benignly. String level external short circuits lead to an unbalanced overdischarge, with one cell going into reversal. The result is catastrophic violent venting. Unbalanced string overdischarges at different currents causes catastrophic violent venting also. Heat-to-vent is very dramatic displaying violent venting Simulated internal short is also catastrophic and displays violent venting. Battery is not UL-rated; hence does not have dual-fault tolerance or tolerance to inherent cell tolerance to failures Battery Design for NASA JSC's human-rated application for use on ISS was changed to include two bypass diodes per cell to provide for two-failure tolerance to overdischarge into reversal (and external short) hazards.

Jeevarajan, J.↗
DOE OSTI2022

Insights into the Enhanced Reversibility of Graphite Anode Upon Fast Charging Through Li Reservoir

Increasing the charging rate and reducing the charging time for Li-ion batteries are crucial to realize the mainstream of electric vehicles. However, it is formidable to avoid the Li plating on graphite anode upon fast charging. Despite the tremendous progress in Li detection techniques, the fundamental mechanism of Li plating and its chemical/electrochemical responses upon cycling still remains elusive. Herein, we present a comprehensive electrochemical method to investigate the fast charging behavior of graphite electrode. A detailed analysis is directed toward understanding the changes in phase, composition, and morphology of the fast-charged graphite. By applying a resting process, we scrutinize the further reactions of the plated Li, which readily transforms into irreversible (dead) Li. We further develop a modified graphite electrode with a thin Ag coating as the Li reservoir. The plated Li can be "absorbed" by the Ag layer to form the Li-Ag solid solution that suppresses the formation of dead Li and provides structural stability, thus promoting the further lithiation of graphite and enhancing the reversibility. Here this work not only provides additional insights into the fast charging behavior of graphite electrode but also demonstrates a potential strategy to improve the fast charging performance of graphite anode.

25 ENERGY STORAGE↗