Search NASA⌕ Search

SEARCH · Search NASA

Results for “root modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Machine learning to accelerate screening for Marcus reorganization energies

Understanding and predicting the charge transport properties of π-conjugated materials is an important challenge for designing new organic electronic devices, such as solar cells, plastic transistors, light-emitting devices, and chemical sensors. A key component of the hopping mechanism of charge transfer in these materials is the Marcus reorganization energy which serves as an activation barrier to hole or electron transfer. While modern density functional methods have proven to accurately predict trends in intramolecular reorganization energy, such calculations are computationally expensive. In this work, we outline active machine learning methods to predict computed intramolecular reorganization energies of a wide range of polythiophenes and their use toward screening new compounds with low internal reorganization energies. Our models have an overall root mean square error (RMSE) of ±0.113 eV, but a much smaller RMSE of only ±0.036 eV on the new screening set. Since the larger error derives from high-reorganization energy compounds, the new method is highly effective to screen for compounds with potentially efficient charge transport parameters.

14 SOLAR ENERGY↗

Small-Signal Analysis of Current-Limiting Grid-Forming Inverters

Grid-forming (GFM) inverters are equipped with a current limiter to protect the device during grid disturbances. Because the intervention of the current limiter can compromise the transient stability of the GFM inverter, various types of current limiter designs and additional frequency-stabilization control methods have been proposed in recent literature to aid in transient GFM inverter stability; however, the small-signal stability implications of adding these additional control blocks during, in particular, off-nominal conditions are not fully understood. To address this challenge, this paper presents a generic small-signal model of a GFM inverter that incorporates various types of current limiters and frequency stability-enhancing controls. With the proposed model, we analyze the root causes of inverter instability, which reveals two critical design trade-offs. First, due to current-limiter engagement caused by a disturbance, the GFM inverter dynamics are altered, which can lead to voltage oscillations. Second, additional frequency-stabilization controls can improve the small-signal stability of the GFM inverter, but at the cost of reduced power and voltage support to the grid. Comprehensive hardware experiments validate the theoretical concept and analysis. The findings in this work underscore the importance of incorporating both transient-response and small-signal dynamics requirements into the design procedure of GFM current limiters and frequency-stabilization controls.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Skyrme-Hartree-Fock-Bogoliubov mass models on a 3D mesh: III. From atomic nuclei to neutron stars

Here, we present BSkG3, the latest entry in the Brussels-Skyrme-on-a-grid series of large-scale models of nuclear structure based on an energy density functional. Compared to its predecessors, the new model offers a more realistic description of nucleonic matter at the extreme densities relevant to neutron stars. This achievement is made possible by incorporating a constraint on the infinite nuclear matter properties at high densities in the parameter adjustment, ensuring in this way that the predictions of BSkG3 for the nuclear Equation of State are compatible with the observational evidence for heavy pulsars with M > 2M ⊙ . Instead of the usual phenomenological pairing terms, we also employ a more microscopically founded treatment of nucleon pairing, resulting in extrapolations to high densities that are in line with the predictions of advanced many-body methods and are hence more suited to the study of superfluidity in neutron stars. By adopting an extended form of the Skyrme functional, we are able to reconcile the description of matter at high densities and at saturation density: the new model further refines the description of atomic nuclei offered by its predecessors. A qualitative improvement is our inclusion of ground state reflection asymmetry, in addition to the spontaneous breaking of rotational, axial, and time-reversal symmetry. Quantitatively, the model offers lowered root-mean-square deviations on 2457 masses (0.631 MeV), 810 charge radii (0.0237 fm) and an unmatched accuracy with respect to 45 primary fission barriers of actinide nuclei (0.33 MeV). Reconciling the complexity of neutron stars with those of atomic nuclei establishes BSkG3 as a tool of choice for applications to nuclear structure, the nuclear equation of state and nuclear astrophysics in general.

Physics↗

Cellulose and the control of growth anisotropy

The overall aim of the award was to understand how the anisotropy of plant cell expansion is controlled by cellulose microfibrils. As experimental material, the project used roots of the popular model plant species, Arabidopsis thaliana. In general, cellulose governs expansion anisotropy by virtue of its strength and organized deposition. Because of their rigidity and alignment, cellulose microfibrils endow the cell wall with mechanical anisotropy; cell walls deform more easily in the direction perpendicular to the microfibrils compared to the parallel direction. Expansion anisotropy thus depends appreciably on the control of cellulose alignment.

59 BASIC BIOLOGICAL SCIENCES↗

Development of a Unified Taxonomy for HVAC System Faults

Detecting and diagnosing HVAC faults is critical for maintaining building operation performance, reducing energy waste, and ensuring indoor comfort. An increasing deployment of commercial fault detection and diagnostics (FDD) software tools in commercial buildings in the past decade has significantly increased buildings’ operational reliability and reduced energy consumption. A massive amount of data has been generated by the FDD software tools. However, efficiently utilizing FDD data for ‘big data’ analytics, algorithm improvement, and other data-driven applications is challenging because the format and naming conventions of those data are very customized, unstructured, and hard to interpret. This paper presents the development of a unified taxonomy for HVAC faults. A taxonomy is an orderly classification of HVAC faults according to their characteristics and causal relations. The taxonomy includes fault categorization, physical hierarchy, fault library, relation model, and naming/tagging scheme. The taxonomy employs both a physical hierarchy of HVAC equipment and a cause-effect relationship model to reveal the root causes of faults in HVAC systems. A structured and standardized vocabulary library is developed to increase data representability and interpretability. The developed fault taxonomy can be used for HVAC system ‘big data’ analytics such as HVAC system fault prevalence analysis or the development of an HVAC FDD software standard. A common type of HVAC equipment-packaged rooftop unit (RTU) is used as an example to demonstrate the application of the developed fault taxonomy. Two RTU FDD software tools are used to show that after mapping FDD data according to the taxonomy, the meta-analysis of the multiple FDD reports is possible and efficient.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗

Predicting Elastic Constants of Refractory Complex Concentrated Alloys Using Machine Learning Approach

Refractory complex concentrated alloys (RCCAs) have drawn increasing attention recently owing to their balanced mechanical properties, including excellent creep resistance, ductility, and oxidation resistance. The mechanical and thermal properties of RCCAs are directly linked with the elastic constants. However, it is time consuming and expensive to obtain the elastic constants of RCCAs with conventional trial-and-error experiments. The elastic constants of RCCAs are predicted using a combination of density functional theory simulation data and machine learning (ML) algorithms in this study. The elastic constants of several RCCAs are predicted using the random forest regressor, gradient boosting regressor (GBR), and XGBoost regression models. Based on performance metrics R-squared, mean average error and root mean square error, the GBR model was found to be most promising in predicting the elastic constant of RCCAs among the three ML models. Additionally, GBR model accuracy was verified using the other four RHEAs dataset which was never seen by the GBR model, and reasonable agreements between ML prediction and available results were found. The present findings show that the GBR model can be used to predict the elastic constant of new RHEAs more accurately without performing any expensive computational and experimental work.

36 MATERIALS SCIENCE↗

Response of wind shear warning systems to turbulence with implication of nuisance alerts

The objective was to predict the inherent turbulence response characteristics of candidate wind shear warning system concepts and to assess the potential for nuisance alerts. Information on the detection system and associated signal processing, physical and mathematical models, wind shear factor root mean square turbulence response and the standard deviation of the wind shear factor due to turbulence is given in vugraph form.

Bowles, Roland L.↗

Observational support for the current sheet catastrophe model of substorm current disruption

The principles of the current sheet catastrophe models are briefly reviewed, and observations of some of the signatures predicted by the theory are presented. The data considered here include AMPTE/CCE observations of fifteen current sheet disruption events. According to the model proposed here, the root cause of the current disruption is some process, as yet unknown, that leads to an increase in the k sub A parameter. Possible causes for the increase in k sub A are discussed.

Burkhart, G. R.↗

Computer Simulation Results and Analysis for a Root-Raised Cosine Filter Design using Canonical Signed Digits

Filters implemented using Canonical Signed-Digit (CSD) number representation for the coefficients have been studied for many years as an efficient way to increase the speed and reduce the hardware complexity. A simple and very effective method for designing a CSD filter with a specific set of filter parameters has been investigated and its simulation results are presented here. In order to optimize filter coefficients into the corresponding CSD numbers, the Minimum Mean Square Error (MMSE) criterion is used. Furthermore, an attempt is made to improve frequency response of the CSD filter by allocating an extra non-zero digit for normalized coefficients exceeding one-half. Due to limited filter aperture width in examples presented here, the frequency response of CSD filter as the number of non-zero digits in a CSD code increases is not affected much. A root-raised cosine filter model is employed as a base line for this design approach. Finally, the CSD filter simulation results and a hardware complexity comparison with a conventional filter are also shown along with the eye diagrams an Bit-Error-Rate (BER) performance curves.

Kim, Heechul↗

A Buffet Investigation at High Subsonic Speeds of Wing-Fuselage-Tail Combinations having Sweptback Wings with NACA Four-Digit Thickness Distributions, Fences, and Body Contouring

An investigation has been made to determine the effect of wing fences, fuselage contouring, varying wing sweepback angle from 40 deg. to 45 deg., mounting the horizontal tail on an outboard boom) and wing thickness distribution upon the buffeting response of typical airplane configurations employing sweptback wings of high aspect ratio. The tests were conducted through an angle-of-attack range at Mach numbers varying from 0.60 to 0.92 at a Reynolds number of 2 million. For the combinations with 40 deg. of sweepback, the addition of multiple wing fences usually decreased the buffeting at moderate and high lift coefficients and reduced the erratic variation of buffet intensities with increasing lift coefficient and Mach number. Fuselage contouring also reduced buffeting but was not as effective as the wing fences. At most Mach numbers, buffeting occurred at higher lift coefficients for the combination with the NACA 64A thickness distributions than for the combination with the NACA four-digit thickness distributions. At high subsonic speeds, heavy buffeting was usually indicated at lift coefficients which were lower than the lift coefficients for static-longitudinal instability. The addition of wing fences improved the pitching-moment characteristics but had little effect on the onset of buffeting. For most test conditions and model configurations, the root-mean- square and the maximum values measured for relative buffeting indicated similar effects and trends; however, the maximum buffeting loads were usually two to three times the root-mean-square intensities.

Sutton, Fred B.↗

Object Detection in Natural Backgrounds Predicted by Discrimination Performance and Models

In object detection, an observer looks for an object class member in a set of backgrounds. In discrimination, an observer tries to distinguish two images. Discrimination models predict the probability that an observer detects a difference between two images. We compare object detection and image discrimination with the same stimuli by: (1) making stimulus pairs of the same background with and without the target object and (2) either giving many consecutive trials with the same background (discrimination) or intermixing the stimuli (object detection). Six images of a vehicle in a natural setting were altered to remove the vehicle and mixed with the original image in various proportions. Detection observers rated the images for vehicle presence. Discrimination observers rated the images for any difference from the background image. Estimated detectabilities of the vehicles were found by maximizing the likelihood of a Thurstone category scaling model. The pattern of estimated detectabilities is similar for discrimination and object detection, and is accurately predicted by a Cortex Transform discrimination model. Predictions of a Contrast- Sensitivity- Function filter model and a Root-Mean-Square difference metric based on the digital image values are less accurate. The discrimination detectabilities averaged about twice those of object detection.

Ahumada, A. J., Jr.↗

Exploratory Studies in Generalized Predictive Control for Active Gust Load Alleviation

The results of numerical simulations aimed at assessing the efficacy of Generalized Predictive Control (GPC) for active gust load alleviation using trailing- and leading-edge control surfaces are presented. The equations underlying the method are presented and discussed, including system identification, calculation of control law matrices, and calculation of commands applied to the control effectors. Both embedded and explicit feedforward paths for inclusion of disturbance effects are addressed. Results from two types of simulations are shown. The first used a 3-DOF math model of a mass-spring-dashpot system subject to user-defined external disturbances. The second used open-loop data from a wind-tunnel test in which a wing model was excited by sinusoidal vertical gusts; closed-loop behavior was simulated in post-test calculations. Results obtained from these simulations have been decidedly positive. In particular, results of closed-loop simulations for the wing model showed reductions in root moments by factors as high as 1000, depending on whether the excitation is from a constant- or variable-frequency gust and on the direction of the response.

Kvaternik, Raymond G.↗

Model Effects on GLAS-Based Regional Estimates of Forest Biomass and Carbon

ICESat/GLAS waveform data are used to estimate biomass and carbon on a 1.27 million sq km study area. the Province of Quebec, Canada, below treeline. The same input data sets and sampling design are used in conjunction with four different predictive models to estimate total aboveground dry forest biomass and forest carbon. The four models include nonstratified and stratified versions of a multiple linear model where either biomass or (square root of) biomass serves as the dependent variable. The use of different models in Quebec introduces differences in Provincial biomass estimates of up to 0.35 Gt (range 4.942+/-0.28 Gt to 5.29+/-0.36 Gt). The results suggest that if different predictive models are used to estimate regional carbon stocks in different epochs, e.g., y2005, y2015, one might mistakenly infer an apparent aboveground carbon "change" of, in this case, 0.18 Gt, or approximately 7% of the aboveground carbon in Quebec, due solely to the use of different predictive models. These findings argue for model consistency in future, LiDAR-based carbon monitoring programs. Regional biomass estimates from the four GLAS models are compared to ground estimates derived from an extensive network of 16,814 ground plots located in southern Quebec. Stratified models proved to be more accurate and precise than either of the two nonstratified models tested.

Nelson, Ross↗

Creating Formal Characterizations of Routine Contingency Management in Commercial Aviation

The identification, modelling, and analysis of root causes of accidents and incidents dominate conventional safety management approaches. However, the effect of humans’ safety-producing behavior on the overall resilience of the system is often neglected. Additionally, emerging aviation markets are giving rise to concepts of operation, such as urban air mobility and optionally piloted air cargo operations, that are leading to a shift in locus of control between humans and automation. Without an understanding of the human contribution to safety, it is difficult to assess the effects of these novel role allocations on overall system safety. In this work, safety-producing behaviors are identified and abstracted into resilient performance strategies. Production rules that encapsulate these strategies are then generated and classified in the Soar cognitive architecture. The strategies are then applied to a remotely-operated air cargo example to demonstrate how safe learning is facilitated. The learned rules and strategies are then formally verified.

Safety Critical Systems↗

Moving Zero Energy Office Buildings to the Mainstream: Establishing Design Guidelines and Energy Targets: Preprint

Office buildings represent a significant portion of the commercial sector and are ideal candidates to lead the market towards achieving zero energy or zero energy ready buildings. The variety of sizes and uses for office buildings make them challenging to determine set design guidance that can be deployed across the market. A project committee for ASHRAE’s Zero Energy - Advanced Energy Design Guide (ZE-AEDG) for small and medium office buildings , comprised of members from five major national associations with market-pull in commercial buildings, created design guidance for achieving zero energy office buildings for new construction and major retrofit. This design guidance focuses on the process, providing a pathway for both office owners and design teams to achieve zero energy status. Energy use intensity targets range from 16 kBtu/ft²·yr to 36 kBtu/ft²·yr for the different climate zones were established such that office buildings can be “zero-ready,” that is, having low energy consumption that can easily be offset with renewables, preferably on-site. The design guidance was rooted in extensive energy modeling, as well as case studies of actual office buildings that have achieved high levels of energy performance and met zero energy or zero energy ready status. A unique aspect of the zero-energy guide is that it is not compared against a baseline but focuses on achieving an absolute target. The paper presents process of creating the targets, the selection of strategies to achieve the targets, and sample case studies that show how the cost-sensitive solutions are achievable for the design community. It also presents outreach strategies to deploy market achievable zero energy measures.

buildings↗