Search NASA⌕ Search

SEARCH · Search NASA

Results for “sample thickness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Diffraction Measurement of Reaction Products in Shock Compressed TATB on the NIF

The shock-induced reaction of high explosives to gaseous and solid reaction products is a rapid, complex process. Understanding solid reaction product structure and formation kinetics is essential in determining the high-pressure equation of state of these multicomponent systems. We use the National Ignition Facility (NIF) to shock compress ~500-µm thick pressed powder high-explosive TATB samples to 70-135 GPa and collect in situ structural data on detonation byproducts using the TARDIS X-ray diffraction diagnostic. Velocimetry is used to record the transmitted compression wave profile, which is well described by Cheetah hydrocode simulations coupled with a reactive flow model, providing strong evidence of reaction in the TATB sample. While an unambiguous determination of the product phases was not possible owing to the low signal-to-noise quality of the diffraction signal, X-ray diffraction data of the product phases formed within the first 50 ns of the reaction is most consistent with a mixture of amorphous products and crystalline hexagonal diamond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Speciation mapping of the oxidation layer on aged uranium dioxide using scanning transmission x-ray spectromicroscopy

In this study, UO 2 was aged in humid air and prepared as a thin section using a focused ion beam (FIB) instrument. The specimen was measured using synchrotron radiation spectromicroscopy techniques at the Beamline 11.0.2 STXM end station of the Advanced Light Source (ALS). Non-negative matrix factorization (NMF) methods were used to identify and map three component x-ray absorption near-edge structure (XANES) spectra in the oxygen K-edge data, revealing a surface layer of U 4 O 9 with a thickness of 206 ± 21 nm, and the bulk of the sample remaining as UO 2 . Uranium N 4,5 -edge XANES spectromicroscopy supports these results. The diffusion-controlled parabolic rate constant for UO 2 oxidation to U 4 O 9 was calculated from the observed layer thickness and compared to literature values. Complementary transmission electron microscopy (TEM) was used to image the sample and identify the phases present in various regions, confirming the STXM results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Transformational faulting in Mn 2 GeO 4 from olivine to wadsleyite structure: Implications for physical mechanism of deep-focus earthquakes

High-pressure and temperature deformation experiments interfaced with acoustic emission (AE) monitoring have been conducted to study transformational faulting in Mn 2 GeO 4 olivine, which transforms to the β phase, isostructural to wadsleyite. Metastable Mn 2 GeO 4 olivine exhibits a marked embrittlement behavior at temperatures between 800 and 1100 K, emitting numerous AEs. At each temperature, brittle deformation is characterized by a two-stage process: (1) a “preparation” stage with numerous diffusedly located low-magnitude AEs and large b values (>2), and (2) a failure stage where larger-magnitude AEs form a planar distribution with b values about 1. Microstructure analysis reveals extensive kink band development in olivine grains in the recovered samples. Kink band boundaries (KBBs), with a typical thickness of ∼100 nm, are filled with a nanometric β-Mn 2 GeO 4 “gouge”. A dense array of secondary shear localizations is often present within the kink bands, suggesting significant shear deformation therein. The combined observations suggest that faulting in metastable Mn 2 GeO 4 olivine is a self-similar process, from grain-scale to the sample-scale. Both observed embrittlement behavior and the microstructure of metastable Mn 2 GeO 4 olivine are essentially identical to those in Mg 2 GeO 4 olivine we have reported previously, indicating that the physical mechanism of faulting in metastable olivine is insensitive to the specific crystallographic structure of the high-pressure phase. The low b values (about 1) observed in the faulting process in our experiments are similar to those of deep focus earthquakes in cold subduction zones. Our observed mechanism explains deep focus seismicity in cold metastable mantle wedges, provided that the self-similarity assumption holds to geological scales.

58 GEOSCIENCES↗
DOE OSTI2023

High-temperature chemical expansion of Pr0.1Ce0.9O2-δ thin films determined by Differential Laser Doppler Vibrometry

The chemical expansion of thin-film praseodymium-cerium oxide solid solutions (Pr 0.1 Ce 0.9 O 2-δ , PCO10) is investigated at temperatures ranging from 500 °C to 800 °C and oxygen activities down to about 10 -22 . Differential Laser Doppler Vibrometry (D-LDV) in combination with periodic electrochemical pumping of oxygen is used to detect very small displacements of the sample surface. With decreasing pumping frequency, the film approaches chemical equilibrium, which is nearly reached at 700 °C below 0.01 Hz. D-LDV enables direct measurement of film thickness changes as well as the bending of the underlying substrates due electrochemically induced lateral mechanical stress. The substrate bending is found to be more than an order of magnitude larger than the film thickness change, increasing the detection limit by the same factor. The thickness change of the thin film is calculated from the measured displacement of the sample surface and compared with directly measured values. Thin-film literature data available for low oxygen activities up to 650 °C agree with our measurements. In addition, the thickness change of the film is determined from the displacement at different sample positions, which validates previous measurements. Finally, thin film chemical expansion is found to be larger by a factor of about 2 than the corresponding bulk value in agreement with predictions from a mechanical model that the out-of-plane expansion of a constrained film is increased.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Downscaling of Non-Van der Waals Semimetallic W 5 N 6 with Resistivity Preservation

The bulk phase of transition metal nitrides (TMNs) has long been a subject of extensive investigation due to their utility as coating materials, electrocatalysts, and diffusion barriers, attributed to their high conductivity and refractory properties. Downscaling TMNs into two-dimensional (2D) forms would provide valuable members to the existing 2D materials repertoire, with potential enhancements across various applications. Moreover, calculations have anticipated the emergence of uncommon physical phenomena in TMNs at the 2D limit. Here, in this study, we use the atomic substitution approach to synthesize 2D W 5 N 6 with tunable thicknesses from tens of nanometers down to 2.9 nm. The obtained flakes exhibit high crystallinity and smooth surfaces. Electrical measurements on 15 samples show an average electrical conductivity of 161.1 S/cm, which persists while thickness decreases from 45.6 to 2.9 nm. The observed weak gate-tuning effect suggests the semimetallic nature of the synthesized 2D W 5 N 6 . Further investigation of the conversion mechanism elucidates the crucial role of chalcogen vacancies in the precursor for initiating the reaction and strain in propagating the conversion. Our work introduces a desired semimetallic crystal to the 2D material library with mechanistic insights for future design of the synthesis.

2D electronics↗
DOE OSTI2020

Reduced Dislocation Introduction in III–V/Si Heterostructures with Glide-Enhancing Compressively Strained Superlattices

The novel use of a GaAs y P 1-y /GaP compressively-strained superlattice (CSS) to provide enhanced control over misfit dislocation (MD) evolution and threading dislocation density (TDD) during GaP/Si metamorphic heteroepitaxy is demonstrated. Here, the insertion of the CSS just after critical thickness, and thus prior to substantial dislocation introduction, is found to yield significantly reduced TDD in relaxed, 500 nm thick, n-type GaP/Si versus comparable control samples. The impact of CSS period count on average TDD and the overall dislocation network morphology was examined, supported by quantitative microstructural characterization, revealing a nearly 20× relative TDD reduction (to 2.4 ± 0.4×10 6 cm -2 ) with a 3-period CSS structure. A similarly low TDD (3.0 ± 0.6×10 6 cm -2 ) is maintained when the resultant n-GaP/Si virtual substrate is used for the growth of a subsequent n-type GaAs 0.75 P 0.25 -terminal GaAs y P 1-y step-graded metamorphic buffer. Although the physical mechanism for TDD reduction provided by these structures is not yet entirely understood, this initial work suggests that enhanced glide dynamics of MDs at or within the CSS placed early in the growth leads to a reduction in the total number of dislocations introduced overall, as opposed to annihilation-based reduction that occurs in conventional strained-layer superlattice dislocation filter approaches.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Development of Advanced, Radiation Resistant, Optical-based Detector Technology for Future Experiments.

The primary objective of this project has been to advance the design of high-performance electromagnetic (EM) calorimeters for future particle physics experiments, to identify and measure the timing, position and energy of electrons, positrons and gamma rays, particularly in high-luminosity environments with intense radiation and pileup conditions. To meet such challenges, the proposed research has focused on the development of ultra-compact, radiation-hard calorimeter modules, to provide excellent timing, spatial, and energy resolution. The work aligns with the DOE’s Basic Research Needs (BRN) for High Energy Physics (HEP) Instrumentation and the research team contributes actively to the Coordinating Panel on Advanced Detectors (CPAD) RDC9 calorimetry collaboration in the USA and the European Committee on Future Accelerators (ECFA) DRD-CALO calorimetry collaboration at CERN, the European Laboratory for Particle Physics located in Geneva, Switzerland. The research builds on the RADiCAL (radiation-hard, ultra-compact) modular sampling calorimeter approach, developed by the research team, which employs dense and very bright optical materials such as LYSO:Ce scintillator plates that are interleaved with very dense tungsten plates to minimize detector size while optimizing performance. The modules are comparable in size to a human index finger, dimensionally 14 mm x 14 mm in cross section and 135 mm in length. And despite the small size, the structure is capable of providing excellent timing and energy resolution. This is facilitated through the use of specialized quartz capillaries filled with wavelength-shifting filaments, positioned at various depths along the length of a module, to collect and guide light signals to silicon photomultipliers (SiPMs) which detect and convert the optical signals to electronic signals for analysis. The primary goals of this project have been: (1) Achieve a timing resolution to σ t ≤ 30 ps for high-energy electrons and photons, important for their association with specific events produced in colliding-beam experiments and for the detection of decays-in-flight of long-lived particles. The project has achieved this goal in beam tests of a single RADiCAL module at CERN, during which a timing resolution of σ t = 27 ps was measured for electrons of energy E = 150 GeV. Based upon a mathematical fit to the data measured over a broad energy range from low energy to high energy, a resolution of σ t ≤ 18 ps has been estimated for electrons of very high (TeV) energy. From these measurements and with further expected technical improvements, the timing resolution should reach σ t ≤ 10 ps, important for searches for discovery physics in upcoming and future experiments. (2) Achieve an energy resolution of σ E / E ≤ 10% / $\sqrt{E}$. The project has yet to achieve this goal, but is close to it, having measured a value of σ E / E ≤ 15.9% / $\sqrt{E}$ using a modular array. Ultimately, the resolution goal is expected to be reached by adjustments to material thicknesses within the modules, which will improve the sampling fraction to measure more precisely the shower energy for lower energy particles. The versatility of the modular RADiCAL approach enables the testing of advanced materials, photosensors and electronics, developed in collaboration with CPAD RDC and ECFA DRD-CALO groups. The structure can distinguish electrons, positrons and gamma rays from hadrons and muons and beam-induced backgrounds, making it a valuable tool in a variety of detector environments, including future circular colliders (FCC-ee, FCC-hh) proposed for the European Laboratory for Particle Physics (CERN), the muon-collider proposed for Fermi National Accelerator Laboratory (Fermilab), and searches for new physics in beam-dump, fixed target and forward-physics experiments. And, while designed with particle physics applications in mind, the technologies developed in this project have the potential for application more broadly in particle and nuclear physics, materials science, and medical physics, underscoring the far-reaching potential of this line of instrumentation research and development.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Reduced scale stripline platform to extend accessible pressures on the Z machine: Shockless compression of platinum to 650 GPa

Reaching astrophysically relevant high energy density (HED) material states in the laboratory is an ongoing effort at multiple experimental facilities. We have developed a new dynamic compression platform for the Z Pulsed Power Facility that allows for sample sizes 100s of [Formula: see text]m in thickness that accommodate multiple grains in order to fully capture bulk properties, such as material strength. A pair of experiments compressed platinum (Pt) to HED conditions and conventional inverse Lagrangian analysis as well as a recent Bayesian calibration technique were used to determine the principal isentrope to 650 GPa with density uncertainties of <2%. These low uncertainties are calculated for single sample experiments, presenting the possibility of even smaller experimental uncertainties with multiple samples the platform allows. Our new platform extends the accessible Pt ramp pressures achievable on the Z machine to over 80% of the pressure recently achieved using the National Ignition Facility planar Hohlraum platform. This new capability, the next generation evolution of the stripline platform, was made possible by advancements in both our understanding of the Z pulsed power driver and our overall magnetohydrodynamic modeling capabilities.

Porwitzky, Andrew↗
DOE OSTI2022

The X-ray view of optically selected dual AGN

We present a study of optically selected dual Active Galactic Nuclei (AGN) with projected separations of 3–97 kpc. Using multiwavelength (MWL) information (optical, X-ray, mid-IR), we characterized the intrinsic nuclear properties of this sample and compared them with those of isolated systems. Among the 124 X-ray-detected AGN candidates, 52 appear in pairs and 72 as single X-ray sources. Through MWL analysis, we confirmed the presence of the AGN in >80 per cent of the detected targets in pairs (42 out of 52). X-ray spectral analysis confirms the trend of increasing AGN luminosity with decreasing separation, suggesting that mergers may have contributed to triggering more luminous AGN. Through X-ray/mid-IR ratio versus X-ray colours, we estimated a fraction of Compton-thin AGN (with 10 22 cm −2 < N H < 10 24 cm −2 ) of about 80 per cent, while about 16 per cent are Compton-thick sources (with N H > 10 24 cm −2 ). These fractions of obscured sources are larger than those found in samples of isolated AGN, confirming that pairs of AGN show higher obscuration. This trend is further confirmed by comparing the de-reddened [O III ] emission with the observed X-ray luminosity. However, the derived fraction of Compton-thick sources in this sample at the early stages of merging is lower than that reported for late-merging dual-AGN samples. Comparing N H from X-rays with that derived from E(B − V ) from narrow-line regions, we found that the absorbing material is likely to be associated with the torus or broad-line regions. We also explored the X-ray detection efficiency of dual-AGN candidates, finding that, when observed properly (at on-axis positions and with long exposures), X-ray data represent a powerful way to confirm and investigate dual-AGN systems.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Method to Determine the Distribution of Substituted or Intercalated Ions in Transition-Metal Dichalcogenides: Fe x VSe 2 and Fe 1– x V x Se 2

Multiple techniques are combined to determine the amount of intercalation and/or substitution in transition-metal dichalcogenides. Kiessig fringes in the X-ray reflectivity pattern are used to calculate thickness. Laue oscillations in the specular diffraction pattern of the crystallographically aligned samples determine the number of unit cells in the coherently diffracting domains. The amount of impurity phase(s) is estimated by the difference between the thickness of the films and the size of the domains. If the difference is small relative to the total film thickness, the composition of the crystalline phase can be determined from X-ray fluorescence measurements. The number of unit cells possible can be calculated from the amount of each element determined by X-ray fluorescence measurements using in-plane lattice parameters, and the amount of the anion should agree with the number of unit cells determined from the Laue oscillations. The total amount of the metal relative to that required for the number of unit cells from the Laue oscillations provides a direct determination of the relative amount of intercalation and/or substitution in the crystalline dichalcogenide. So the utility of this approach is illustrated in Fe x V 1–y Se 2 samples. The relative amount of intercalation versus substitution was determined independently using electron microscopy and Rietveld refinement of diffraction patterns and is consistent with this new approach.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Exchange Bias Between van der Waals Materials: Tilted Magnetic States and Field-Free Spin–Orbit-Torque Switching

Magnetic van der Waals heterostructures provide a unique platform to study magnetism and spintronics device concepts in the 2D limit. Here, studies of exchange bias from the van der Waals antiferromagnet CrSBr acting on the van der Waals ferromagnet Fe3GeTe2 (FGT) are reported. Additionally, the orientation of the exchange bias is along the in-plane easy axis of CrSBr, perpendicular to the out-of-plane anisotropy of the FGT, inducing a strongly tilted magnetic configuration in the FGT. Furthermore, the in-plane exchange bias provides sufficient symmetry breaking to allow deterministic spin–orbit torque switching of the FGT in CrSBr/FGT/Pt samples at zero applied magnetic field. A minimum thickness of the CrSBr of >10 nm is needed to provide a non-zero exchange bias at 30 K.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Direct Fabrication of Vertically Stacked Double Barrier Tunnel Junctions Based on Graphene and h-BN

Direct manufacturing of two-dimensional material-based double barrier (DB) tunnel junctions, based on a lithography-free approach was developed. Graphene/h-BN/Graphene/h-BN/Graphene devices were deposited on Si/SiO2 substrates by employing a plasma enhanced chemical vapor deposition technique in a sequential manner. DB tunneling junctions with varying barrier widths (by varying the thickness of the second graphene layer) were studied. Samples were characterized using Raman, Atomic Force Microscopy and X-ray photoemission spectroscopy. The I–V characteristics of tunneling current showed resonant tunneling behavior at room temperature with a negative differential conductance. The behavior could be explained with quantum mechanical double barrier tunneling model in which analytic solutions to Schrödinger’s equation were obtained in each region of the system. Resonances in transmission probability coefficient for varying barrier widths were evaluated and compared with the experimental results.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Anisotropic spall failure of additively manufactured 316L stainless steel

The dynamic high strain rate tensile (spall) failure of additively manufactured (AM) materials is an area of great interest but much less understood than material failure under other loading regimes. The research presented here examines the effects of microstructure anisotropy in 316L stainless steel fabricated by laser powder bed fusion (LPBF) on its spall failure and properties. In this work, plate-on-plate impact experiments were performed using an 80-mm gas gun to investigate the spall behavior of AM fabricated sample discs with impact along the perpendicular and parallel orientations relative to build directions. Experiments were also performed on wrought 316L stainless steel as baseline material with uniform equiaxed grain microstructure for comparison with the AM material of same composition. The spall experiments involved free-surface velocity profiles measured using Photon Doppler Velocimetry (PDV) to capture the spall pull-back signals, combined with post-mortem analysis of the microstructure of soft-recovered impacted samples. In the case of AM samples, spall failure initiated preferentially at melt pool boundaries in both impact directions. The spall plane location and spall strength, however, were both heavily influenced by the orientation of the impact direction relative to the build direction in the AM samples. The spall behavior is also observed to be more complex in the samples impacted perpendicular to the build (through-thickness) direction, due in large part to the orientation of the microstructural features such as melt pool boundaries, laser scan tracks, and general grain morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2021

An Atom Probe Tomography Study of the Through Wall Attenuation Effect on Cu-rich Precipitate Formation in a Reactor Pressure Vessel Steel

In this study, high-Cu weld material harvested from an ex service reactor pressure vessel (RPV) steel from Unit 1 of the decommissioned Zion Nuclear Generating Station has been characterized using atom probe tomography. Samples taken from 4 different positions through the thicknesses of the pressure vessel wall from the water-side to the air-side were characterized, along with an unirradiated baseline material. In the baseline material, no precipitates were found and the Cu was observed to be fully in solid solution; however, scanning transmission electron microscopy combined with energy dispersive spectroscopy (STEM-EDS) revealed the presence of ϵ -Cu that form during processing of the material and results in the concomitant decrease of matrix Cu. Following irradiation, a high number density of nano-scale Cu-rich precipitates (CRPs) were observed, uniformly distributed throughout the matrix. The Cu content within the CRPs was found to be ~30-35 at.% regardless of location in the wall. No statistically significant variation in the compositions, mean radius, number density, or volume fraction as a function of location within the wall was observed. The measured matrix Cu level excluding CRPs contribution was found to be ~90 appm higher than the solubility limit suggesting that further nucleation and growth of the CRPs under continued operations would have occurred. These results clearly demonstrate that the neutron energy attenuation has no significant effect on the precipitation kinetics of CRPs regardless of location in the wall in high-Cu RPV steels under irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

La-Based Perovskite Oxide Catalysts for Alkaline Oxygen Reduction: The Importance of Electrochemical Stability

Alkaline fuel cells represent a promising energy conversion technology since they enable the use of precious metal-free electrocatalysts for the oxygen reduction reaction. Among these, La-based perovskite oxides, with great compositional and structural tunability, are especially attractive. However, we believe that the current literature lacks a thorough understanding of their inherent (in)stability issues. Here, in this study, we report on nine La-based perovskite oxide electrocatalysts for the oxygen reduction reaction, including LaMO 3 (M = Mn, Co, Ni) and LaCo x M 1–x O 3 (M = Mn, Ni; x = 0.9, 0.5, 0.1). While some exhibited initial promising activity, they all degraded significantly, even after brief electrochemical testing. Through comprehensive structural characterization of LaCo 0.9 Mn 0.1 O 3 , particularly scanning transmission electron microscopy, we found evidence to support a degradation mechanism in which the B-site cation species irreversibly leach from the perovskite under testing conditions. A sample cycled 10 000 times from +0.4 to +1.2 V vs reversible hydrogen electrode (RHE) showed an amorphous La oxide shell 1–2 nm thick. Bulk analyses showed that B-site leaching also occurs for samples soaked in 1 M KOH or pure EtOH. The mechanistic insights provided here should help inform the future design of La-based perovskite oxide electrocatalysts for alkaline fuel cells and stress the importance of stability metrics validating claims of promising electrocatalytic activity.

Seok, Jeesoo↗
DOE OSTI2024

VitroJet: new features and case studies

Single-particle cryo-electron microscopy has become a widely adopted method in structural biology due to many recent technological advances in microscopes, detectors and image processing. Before being able to inspect a biological sample in an electron microscope, it needs to be deposited in a thin layer on a grid and rapidly frozen. The VitroJet was designed with this aim, as well as avoiding the delicate manual handling and transfer steps that occur during the conventional grid-preparation process. Since its creation, numerous technical developments have resulted in a device that is now widely utilized in multiple laboratories worldwide. It features plasma treatment, low-volume sample deposition through pin printing, optical ice-thickness measurement and cryofixation of pre-clipped Autogrids through jet vitrification. This paper presents recent technical improvements to the VitroJet and the benefits that it brings to the cryo-EM workflow. A wide variety of applications are shown: membrane proteins, nucleosomes, fatty-acid synthase, Tobacco mosaic virus, lipid nanoparticles, tick-borne encephalitis viruses and bacteriophages. These case studies illustrate the advancement of the VitroJet into an instrument that enables accurate control and reproducibility, demonstrating its suitability for time-efficient cryo-EM structure determination.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Evaluation of the Reconstruction Accuracy of the Ultrasound Model–Based Image Reconstruction (U-MBIR) Method for Concrete to Optimize Damage Detection

Reinforced concrete is a critical structural material used to construct nuclear power plants (NPPs). As such, its safety and performance must be thoroughly examined throughout the life cycle of the NPP infrastructure system. Ultrasonic measurements have been an industry standard for both surface and subsurface inspections. To support the development of these techniques, Oak Ridge National Laboratory (ORNL) has researched and developed advanced image reconstruction algorithms to capture internal damage. The results and discussion presented herein summarize the current state of the ultrasonic model–based iterative reconstruction (U-MBIR) algorithm developed at ORNL. In the work documented in this report, the U-MBIR methodology was applied to four sets of ultrasonic data collected from concrete specimens. The results demonstrate that the U-MBIR algorithm can successfully detect defects within the four concrete samples. The reconstruction images help identify the specimen thickness, regions of delamination, and location of rebar embedded within the concrete. The reconstruction images allow engineers and technicians to characterize the internal defects within concrete specimens and structural members. Ultimately, this knowledge can guide engineers in making informed decisions regarding the performance, safety, and reliability of structural materials (i.e., reinforced concrete) throughout the life cycle of NPPs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Sputter coating of Nb₃Sn into SRF cavity using stoichiometric target

Nb₃Sn has emerged as a leading alternative material due to its higher superconducting critical temperature (Tc) and superheating field (Hsh), promising a viable solution to the intrinsic performance limit currently faced by Nb superconducting radiofrequency (SRF) cavities. We sputter-coated Nb₃Sn inside Nb SRF cavity using a stoichiometric Nb₃Sn tube target in a DC cylindrical magnetron sputter coater. The target was fabricated by growing an estimated >20 μm thick Nb₃Sn layer on a Nb tube via Sn vapor diffusion using Jefferson Lab’s coating system. Approximately 150 nm thick Nb-Sn films were sputter-deposited onto flat Nb samples at positions representing the beam tubes and equator of a 2.6 GHz Nb cavity. Post-deposition annealing at 950 °C for 3 h resulted in the formation of Nb₃Sn. Microstructural analysis of the annealed films was carried out to investigate the morphology and structure of the Nb₃Sn films. Later, a 2.6 GHz Nb SRF cavity was coated with a ~1.2 μm thick sputtered Nb-Sn film using a stoichiometric Nb₃Sn target, followed by annealing. Cryogenic RF testing of the annealed cavity demonstrated a Tc of 17.8 K, indicating the formation of Nb₃Sn. After a light Sn recoating treatment, the cavity achieved a quality factor (Q0) of 6.7E+08 at lower field at 2.0 K.

Accelerator Physics↗