SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The structure–property relationship of single-atom alloy catalysts is reviewed from the perspective of atomic structure analysis, electronic properties, and catalytic activities.
The identification of thermodynamic descriptors of catalytic performance is essential for the rational design of heterogeneous catalysts. Here, we investigate how spillover energy, a descriptor quantifying whether intermediates are more stable at the dopant or host metal sites, can be used to design single-atom alloys (SAAs) for formic acid dehydrogenation. Further, using theoretical calculations, we identify NiCu as a SAA with favorable spillover energy and demonstrate that formate intermediates produced after the initial O–H activation are more stable at Ni sites where rate-determining C–H activation occurs. Surface science experiments demonstrated that NiCu(111) SAAs are more reactive than Cu(111) while they still follow the formate reaction pathway. However, reactor studies of silica-supported NiCu SAA nanoparticles showed only a modest improvement over Cu resulting from surface coverage effects. Overall, this study demonstrates the potential of engineering SAAs using spillover energy as a design parameter and highlights the importance of adsorbate–adsorbate interactions under steady-state operation.
Plastic imposes a critical threat to the environment, ecosystems, and human health because of the low utilization efficiency of plastics. Here, we demonstrate a sustainable, highly efficient cascade photocatalysis for upcycle plastics to value-added acetic acid using Fe single-atom catalysts (Fe@C 3 N 4 SAC) at ambient conditions. Inspired by Phanerochaete chrysosporium microbial, the defective Fe@C 3 N 4 SAC acts as a bifunctional cascade photocatalyst for both Fenton-like and CO 2 reduction reactions. During the reaction, hydroxyl radicals (*OH) form and subsequently oxidize plastics into CO 2 intermediates. These CO 2 intermediates are then photo-reduced to CH 3 COOH on the same catalyst via cascade photocatalysis. The mechanism is confirmed by in situ multimodal microscopy and spectroscopies, with density functional theory calculations. A state-of-art CH 3 COOH yield of 63.8 mg h −1 gcat −1 from PVC, 12.7 mg h −1 gcat −1 from PE, 5.4 mg h −1 gcat −1 from PET, and 5.3 mg h −1 gcat −1 from PP are directly obtained under AM1.5G solar irradiation and further validated under real sunlight (≈0.6 sun), achieving 5.6 mg h −1 gcat −1 from PET, using low-cost Fe@C 3 N 4 SAC in a sealed reactor by enhancing the photon transport and utilization efficiency. The techno-economic analysis shows it is promising to practically mitigate plastic based on broader social welfare assessments.
Abstract Nanomaterials with core-shell architectures are prominent examples of strain-engineered materials. The lattice mismatch between the core and shell materials can cause strong interface strain, which affects the surface structures. Therefore, surface functional properties such as catalytic activities can be designed by fine-tuning the misfit strain at the interface. To precisely control the core-shell effect, it is essential to understand how the surface and interface strains are related at the atomic scale. Here, we elucidate the surface-interface strain relations by determining the full 3D atomic structure of Pd@Pt core-shell nanoparticles at the single-atom level via atomic electron tomography. Full 3D displacement fields and strain profiles of core-shell nanoparticles were obtained, which revealed a direct correlation between the surface and interface strain. The strain distributions show a strong shape-dependent anisotropy, whose nature was further corroborated by molecular statics simulations. From the observed surface strains, the surface oxygen reduction reaction activities were predicted. These findings give a deep understanding of structure-property relationships in strain-engineerable core-shell systems, which can lead to direct control over the resulting catalytic properties.
Enhancing catalytic activity by decorating noble metals in catalysts provides an opportunity for promoting the electrocatalytic hydrogen evolution reaction (HER) application. However, there are few systematic studies on regulating the structures of noble metals in catalytic materials and investigating their influence on HER. Herein, Pt catalysts with different structures including single atoms (SAs), clusters, and nanoparticles well-controllably anchored on VS 2 nanosheets through a cost-effective optothermal method are reported, and their HER performance is studied. The most efficient Pt-decorated VS 2 catalyst (with both Pt SAs and clusters) delivers an overpotential of 77 mV at 10 mA cm –2 , close to that of Pt/C (48 mV). However, the optimal mass activity of Pt (normalizing to Pt content) is obtained from only SA Pt-decorated VS 2 (i.e., 22.88 A mg Pt –1 at 200 mV) and is 12 times greater than that of the Pt/C (1.87 A mg Pt –1 ), attributed to the greatly enhanced Pt utilization. Additionally, the theoretical simulations reveal that Pt SA decoration makes the adsorption free energy of H* closer to the thermoneutral value and improves the charge-transfer kinetics, significantly enhancing HER activity. Furthermore, this work offers a pathway to prepare the desired catalyst based on synergy of Pt structures and VS 2 and reveals the intrinsic mechanism for enhancing catalytic activity, which is important for HER applications.
Abstract Heme enzymes, with the pentacoordinate heme iron active sites, possess high catalytic activity and selectivity in biosensing applications. However, they are still subject to limited catalytic stability in the complex environment and high cost for broad applications in electrochemical sensing. It is meaningful to develop a novel substitute that has a similar structure to some heme enzymes and mimics their enzyme activities. One emerging strategy is to design the Fe‐N‐C based single‐atomic site catalysts (SASCs). The obtained atomically dispersed Fe‐N x active sites can mimic the active sites of heme enzymes effectively. In this work, a SASC (Fe‐SASC/NW) is synthesized by doping single iron atoms in polypyrrole (PPy) derived carbon nanowire via a zinc‐atom‐assisted method. The proposed Fe‐SASC/NW shows high heme enzyme‐like catalytic performance for hydrogen peroxide (H 2 O 2 ) with a specific activity of 42.8 U mg −1 . An electrochemical sensor based on Fe‐SASC/NW is developed for the detection of H 2 O 2 . This sensor exhibits a wide detection concentration range from 5.0 × 10 −10 m to 0.5 m and an excellent limit of detection (LOD) of 46.35 × 10 −9 m . Such excellent catalytic activity and electrochemical sensing sensitivity are attributed to the isolated Fe‐N x active sites and their structural similarity with natural metalloproteases.
Metal-acid bifunctional catalysts are the unity of two opposites (metal-acid repelling) for cellulosic biomass valorization to isosorbide. It is challenging to improve the selectivity of metal hydrogenation catalysts and their synergism with acids for catalytic hydrolysis and dehydration to achieve substantial isosorbide. Herein, dense Ru single-atoms (10.1 wt% of Ru SAs) are anchored on sulfoacid-functionalized hollow mesoporous carbon shells, designed by assembling silica and 8-hydroxyquinoline-modified chitosan (HQ-CTS) through in situ Stöber templating strategy before pyrolysis and acid treatment. Based on X-ray absorption fine structure and computational modeling results, the structure of Ru SAs is determined as RuN 4 , which is more selective for a transitional glucose hydrogenation to sorbitol than Ru001 of Ru clusters. A lower-energy barrier of 1.21 (0.72) eV is delivered over RuN 4 (Ru001) for glucose hydrogenation (isomerization). These Ru SAs are integrated with sulfoacids (SO 3 H) but resistent against acids, rendering enhanced isosorbide yield in water as compared to Ru clusters, via a one-pot cascade reaction under harsh conditions (220 °C, 6 MPa H 2 ). The elaborately fabricated dense Ru SAs and sulfoacids, achieved by varying the addition time of HQ-CTS during the in situ Stöber templating process, improve the synergism of glucose hydrogenation with cellulose hydrolysis and sorbitol dehydration. In conclusion, this study provides a new idea for rational design of high-performance metal-acid bifunctional catalysts toward one-pot conversion of cellulose to isosorbide.
Despite the various strategies for achieving metal–nitrogen–carbon (M–N–C) single-atom catalysts (SACs) with different microenvironments for electrochemical carbon dioxide reduction reaction (CO 2 RR), the synthesis–structure–performance correlation remains elusive due to the lack of well-controlled synthetic approaches. Here, we employed Ni nanoparticles as starting materials for the direct synthesis of nickel (Ni) SACs in one spot through harvesting the interaction between metallic Ni and N atoms in the precursor during the chemical vapor deposition growth of hierarchical N-doped graphene fibers. By combining with first-principle calculations, we found that the Ni-N configuration is closely correlated to the N contents in the precursor, in which the acetonitrile with a high N/C ratio favors the formation of Ni-N 3 , while the pyridine with a low N/C ratio is more likely to promote the evolution of Ni-N 2 . Moreover, we revealed that the presence of N favors the formation of H-terminated edge of sp 2 carbon and consequently leads to the formation of graphene fibers consisting of vertically stacked graphene flakes, instead of the traditional growth of carbon nanotubes on Ni nanoparticles. With a high capability in balancing the *COOH formation and *CO desorption, the as-prepared hierarchical N-doped graphene nanofibers with Ni-N 3 sites exhibit a superior CO2RR performance compared to that with Ni-N 2 and Ni-N 4 ones.
Electroreduction of carbon dioxide (CO 2 ) or carbon monoxide (CO) toward C 2+ hydrocarbons such as ethylene, ethanol, acetate and propanol represents a promising approach toward carbon-negative electrosynthesis of chemicals. Fundamental understanding of the carbon–carbon (C-C) coupling mechanisms in these electrocatalytic processes is the key to the design and development of electrochemical systems at high energy and carbon conversion efficiencies. Here, we report the investigation of CO electreduction on single-atom copper (Cu) electrocatalysts. Atomically dispersed Cu is coordinated on a carbon nitride substrate to form high-density copper–nitrogen moieties. Chemisorption, electrocatalytic, and computational studies are combined to probe the catalytic mechanisms. Unlike the Langmuir-Hinshelwood mechanism known for copper metal surfaces, the confinement of CO adsorption on the single-copper-atom sites enables an Eley-Rideal type of C-C coupling between adsorbed (*CO) and gaseous [CO(g)] carbon moxide molecules. The isolated Cu sites also selectively stabilize the key reaction intermediates determining the bifurcation of reaction pathways toward different C 2+ products.
Lithium–sulfur batteries (LSBs) emerge as promising next-generation energy storage systems offering cost-effectiveness, environmental friendliness, and high theoretical energy density. The practical implementation of LSBs faces significant hindrances due to the shuttle effect and sluggish redox reactions. To address these challenges, single-atom catalyst (SAC) based combination materials from d-block elements can offer increased active catalytic sites, rapid charge transfer, accelerated electron migration, and fast sulfur redox conversion kinetics of lithium polysulfides (LiPSs). In this study, we fabricated three different LSB cathodes: pure S, S@MoS 2 /SnS 2 , and S@Fe–MoS 2 /SnS 2 . These cathodes were then used to explore the cycle life, capacity, rate capability, and redox kinetic reactions of LiPSs while assessing the influence of Fe-SACs on their performance. As a result, LSBs with S@Fe–MoS 2 /SnS 2 cathodes demonstrate an extended cycle life of 1000 cycles at a C-rate of 0.2C, maintaining a capacity close to 500 mA h g −1 , the highest initial discharge capacity of 1622 mA h g −1 and 1066 mA h g −1 at 0.05C and 0.2C, and excellent rate capabilities of 708 mA h g −1 and 558 mA h g −1 at 1C and 2C, respectively. The synergistic effect of the Fe-SAC-based combination cathode (S@Fe–MoS 2 /SnS 2 ) creates plentiful adsorptive and highly active catalytic sites, resulting in substantially enhanced capacity for adsorbing soluble long-chain LiPSs. This facilitates ultra-fast redox kinetics, surpassing the performance of the S@MoS 2 /SnS 2 and pure S cathodes. In the ex situ analysis, results from powder X-ray diffraction (XRD) to observe the new phase, soft X-ray absorption spectroscopy (XAS) to investigate the electronic structure, and hard X-ray photoelectron microscopy (HAXPES) with different energies (900 eV, 2000 eV, and 6000 eV) to track the chemical-state evolution of Fe-SACs in MoS 2 /SnS 2 cathodes displayed notable electrochemical reversibility involving S 8 ⇄ LiPSs ⇄ Li 2 S conversion even after 1000 cycles. Additionally, in situ, operando Raman analysis can unveil a novel catalytic mechanism of Fe-SACs in MoS 2 /SnS 2 “facilitating rapid electron transfer” during the discharge and charge processes of LSBs involving the conversion of S 8 ⇄ long-chain LiPSs ⇄ Li 2 S 2 /Li 2 S. This study elucidates the working mechanism of Fe-SAC cathodes, offering insights into overcoming the shuttle effect and facilitating sulfur redox kinetics to advance commercial LSBs.
The presence of multiple reactant gases as well as reaction intermediates in a heterogeneous catalytic reaction results in a complex interaction between different components of the catalyst with each gas, which can alter the surface and chemical state of the catalyst differently than in the presence of an individual gas alone. In this study, we used in situ ambient pressure x-ray photoelectron spectroscopy to study the surface state of Pt/Cu(111) single-atom alloy model system in two catalytically relevant reaction conditions: CO 2 hydrogenation and CO oxidation. We found that the activation of CO 2 results in the formation of CO, which adsorbs on Pt sites at up to 400 K. In the presence of CO 2 and H 2 , Pt catalyzes the reverse water–gas shift reaction, which produces more CO and further stabilizes surface Pt atoms at 450 K. On the other hand, in CO oxidation condition, the presence of O 2 results in the formation of a thick Cu 2 O layer at higher temperatures, and Pt atoms are no longer detected in the surface and subsurface layers. When O 2 is introduced to the sample before CO, the formation of a complete Cu 2 O layer that covers all Pt atoms occurs immediately at room temperature. Finally, however, when CO is introduced at room temperature before O 2 , the presence of adsorbed CO on Pt sites stabilizes the surface Pt atoms and prevents the formation of a complete Cu 2 O layer, thus exposing the Pt atoms in 'holes' in the Cu 2 O layer.
Redox cocatalysts play crucial roles in photosynthetic reactions, yet simultaneous loading of oxidative and reductive cocatalysts often leads to enhanced charge recombination that is detrimental to photosynthesis. This study introduces an approach to simultaneously load two redox cocatalysts, atomically dispersed cobalt for improving oxidation activity and anthraquinone for improving reduction selectivity, onto graphitic carbon nitride (C 3 N 4 ) nanosheets for photocatalytic H 2 O 2 production. Spatial separation of oxidative and reductive cocatalysts was achieved on a two-dimensional (2D) photocatalyst, by coordinating cobalt single atom above the void center of C 3 N 4 and anchoring anthraquinone at the edges of C 3 N 4 nanosheets. Such spatial separation, experimentally confirmed and computationally simulated, was found to be critical for enhancing surface charge separation and achieving efficient H 2 O 2 production. This center/edge strategy for spatial separation of cocatalysts may be applied on other 2D photocatalysts that are increasingly studied in photosynthetic reactions.
The advancement of efficient, cheap, and durable catalysts for oxygen reduction reaction (ORR) to substitute Pt/C in metal-air batteries is of paramount importance. However, traditional solvent-based methods fall short in terms of environmental benign and scalability. Herein, a solvent-free organic-inorganic self-assembly approach is explored to construct cobalt single atom and cobalt nanocluster decorated nitrogen-doped porous carbon spheres (Co-SA/NC@NCS). The solvent-free synthesis demonstrates an impressively high yield (282 g/L) and the resultant Co-SA/NC@NCS possesses a high N content (6.9 wt%). Density functional theory calculations disclose that the Co-SAs and Co-NCs are able to optimize the surface oxygen adsorption capability and enhance the conductivity of the NCS, thereby facilitating the ORR performance. Here, the solvent-free synthesis is also feasible for the synthesis of other non-noble metal element (Fe, Ni, and Zn) decorated nitrogen-doped porous carbon spheres.
Based on the hydrogen spillover effect, versatile binary-site catalysts are promising for the alkaline hydrogen evolution reaction (HER). In which one site can adsorb and dissociate water, while the neighboring site is favorable for liberating hydrogen. Inspired by these possibilities, oxygen vacancy (O v )-rich LaCeO x coupled N-doped graphene/Ru single-atoms (LaCeO x @NGr/Ru 1 ) was synthesized as an efficient dual-site HER catalyst. It delivered an impressive low overpotential of 22 mV at a current density of 10mAcm –2 and a slight Tafel slope of 40 mV dec –1 in an alkaline medium, outstanding the advanced Ru-based catalysts. Moreover, this promising binary-component catalyst exhibited higher mass activity and longer lasting durability than commercial Pt/C catalyst (20 wt%). Finally, experimental and theoretical investigations provided insights into the HER mechanisms of LaCeO x @NGr/Ru 1 based on three indispensable steps: water adsorption and dissociation on O v -rich LaCeO x , diffusion of generated H* species towards Ce 3+ -N-Ru 1 bridges, and hydrogen evolution on Ru 1 sites.
Methane (CH 4 ) and hydrogen (H 2 ) show promise as low-carbon energy sources, but their impurities, including H 2 and CO, pose challenges for storage and use. To address these challenges, a robust purification protocol for CH 4 and/or H 2 , combined with the catalytic conversion of impurities into CO 2 and H 2 O, is a compelling solution. Here, in this work, we investigated 11 phosphotungstic acid (PTA)-supported single-atom catalysts (SACs) by density functional theory (DFT) computations. Os 1 /PTA SACs exhibited superior catalytic activity, and the ease of oxidation follows the CO > H 2 > CH 4 order. It facilitated efficient purification of CH 4 in solvents such as water, MeOH, and various others. For H 2 purification, Os 1 /PTA SACs demonstrated excellent performance in gas, water, and MeOH. Notably, in water and MeOH, it selectively removed CO without consuming H 2 with low free energy barriers. The strong Os-PTA interactions and charge transfer mechanism contributed to its exceptional catalytic activity. Our findings shed light on SAC behavior and their potential for efficient CH 4 and H 2 purification. By addressing impurity challenges and improving clean energy utilization, these findings contribute to the development of sustainable energy technologies.
We report the high voltage in oxygen evolution reaction (OER) often causes structural change in electrocatalysts and forms multiple active sites. Therefore, exploring the synergy of various active sites is extremely significant to develop catalysts for OER with multiple elementary steps. Herein, we adopt the physically adsorbed metal ions method to successfully synthesize a highly-efficient electrocatalyst containing the dual active sites of Fe-NiOOH and NiC4 single atoms (marked as Ni SAs/Fe-NiOOH). The Ni SAs/Fe-NiOOH displays outstanding OER performance with an overpotential of 269 mV to deliver current density of 10 mA/cm 2 that shows 55 mV superior to commercial IrO 2 /CB at the same condition. Experiments and density functional theory calculations indicate that the excellent OER activity of Ni SAs/Fe-NiOOH catalyst is attributed to the synergy of dual active sites of NiC 4 SAs and Fe-NiOOH. A tandem catalysis mechanism is also proposed to reveal the synergism of two active centers, which makes the potential-determining step more facile and accordingly decreases the OER overpotential. This work offers a new concept of tandem catalysis to develop the electrocatalysts with many elemental steps, like OER and oxygen reduction reaction catalysts.
Reactive separations of CO/CO 2 mixtures are a promising pathway to lower the energy requirement of CO 2 hydrogenation to chemicals and fuels, with applications in the U.S. Navy’s seawater-to-fuel process. With the CO/CO 2 feedstock, a challenge is activating CO to produce heavier hydrocarbons while preventing CO 2 methanation, requiring low-temperature Fischer-Tropsch synthesis (FTS) catalysts. In this work, we demonstrate that a Ru–Co single atom alloy (SAA) catalyst produces C 5+ hydrocarbons at a rate of 11.7 μmol/s/g-cobalt (hexane basis) in a 50/50 CO/CO 2 stream with ≤1% CO 2 conversion. The reaction operates at a relatively low temperature (200 °C) and high gas hourly space velocity (GHSV: 84,000 mL/g/h) that is compatible with the upstream reverse water-gas shift reaction. Detailed experiments, catalyst characterizations, and density functional theory (DFT) calculations have been conducted to understand the active phase, the role of the Ru dopant, and catalyst restructuring that occurs at elevated temperatures (>200 °C). Ru dopants are found to promote the reduction of Co species, enabling catalytic activity for CO hydrogenation without pre-reduction, but may not enhance the FTS activity or desired C 5+ hydrocarbon selectivity.
The selective catalytic oxidation of methanol to methyl formate (MF) has been considered as an attractive route to produce MF, an important precursor in the chemical industry. Although supported Pd nanoparticles are active for the selective oxidation of methanol to MF, the relatively low MF selectivity and yield remains an unsolved issue. Here in this paper, we show that adding a small amount of Pd into Cu forming PdCu single atom alloy (SAA) catalysts can catalyze the oxidation of methanol to MF selectively at low temperatures, with a high catalyst stability. The atomic dispersion of Pd atoms in the Cu matrix was confirmed by various in-situ characterization techniques. The activity and selectivity of PdCu SAA catalysts were compared to monometallic Cu and Pd catalysts, in a flow reactor at similar conditions. This work may guide the design of new SAA based catalysts for selective oxidation reactions.