Search NASA⌕ Search

SEARCH · Search NASA

Results for “skin coefficient of friction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

211 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

An Experimental Study of the Ground Transportation System (GTS) Model in the NASA Ames 7- by 10-Ft Wind Tunnel

The 1/8-scale Ground Transportation System (GTS) model was studied experimentally in the NASA Ames 7- by 10-Ft Wind Tunnel. Designed for validation of computational fluid dynamics (CFD), the GTS model has a simplified geometry with a cab-over-engine design and no tractor-trailer gap. As a further simplification, all measurements of the GTS model were made without wheels. Aerodynamic boattail plates were also tested on the rear of the trailer to provide a simple geometry modification for computation. The experimental measurements include body-axis drag, surface pressures, surface hot-film anemometry, oil-film interferometry, and 3-D particle image velocimetry (PIV). The wind-averaged drag coefficient with and without boattail plates was 0.225 and 0.277, respectively. PIV measurements behind the model reveal a significant reduction in the wake size due to the flow turning provided by the boattail plates. Hot-film measurements on the side of the cab indicate laminar separation with turbulent reattachment within 0.08 trailer width for zero and +/- 10 degrees yaw. Oil film interferometry provided quantitative measurements of skin friction and qualitative oil flow images. A complete set of the experimental data and the surface definition of the model are included on a CD-ROM for further analysis and comparison.

Storms, Bruce L.↗
NASA NTRS1951

On the turbulent friction layer for rising pressure

Among the information presented are included displacement, momentum, and kinetic energy thicknesses, shearing stress distributions across boundary layer, and surface friction coefficients. The Gruschwitz method and its modifications are examined and tested. An energy theorem for the turbulent boundary layer is introduced and discussed but does not lead to a method for the prediction of the behavior of the turbulent boundary layer because relations for the shearing stress and the surface friction are lacking.

SKIN FRICTION - PLATES↗
NASA NTRS1981

An experimental and computational investigation of the transport of Reynolds stress in an axisymmetric swirling boundary layer

A coordinated experimental and computational investigation of the transport and interaction of the individual Reynolds stresses within a turbulent axisymmetric swirling boundary layer flowing over a stationary cylinder is described. The cylinder is instrumented with new directional surface fence skin-friction gages developed for the experiment. The longitudinal and transverse mean velocity profiles are measured with a miniature directional pressure probe. These data provided a standard on which to compare computed results employing a variety of turbulence models. The turbulence models tested range from a simple mixing length model, through a two-equation model, on to the Reynolds stress equation models. The full Reynolds stress equation models are tested with various sets of modeling coefficients for the pressure rate-of-strain correlation. It is shown that while even the simplest model shows the general features of the data, agreement with the experimental data is enhanced through the use of the more complex models. For a better prediction of the data, however, further model improvement is still required.

Higuchi, H.↗
NASA NTRS2001

Cranked Arrow Wing (F-16XL-1) Flight Flow Physics with CFD Predictions at Subsonic and Transonic Speeds

The computational fluid dynamics (CFD) modeling used has produced reasonably good global upper-surface pressure coefficient comparisons with measured flight data at both transonic and subsonic speeds at the angles of attack presented. Boundary layer comparisons showed the profiles to be reasonably well predicted inboard and under the primary vortex system. However, the secondary vortex profile was not well predicted either at the anticipated separation point or under the secondary vortex. Moreover, the flight data showed there to be a vortex/boundary-layer interaction that occurred in the vicinity of the secondary vortex. The spanwise distribution of local skin friction measured data was reasonably well predicted, especially away from the wing leading-edge. Lastly, predicted and measured flight-pressures, as well as flight-image data, for the F-16XL-1 airplane are now available via the World Wide Web.

Lamar, John E.↗
NASA NTRS2003

Cranked Arrow Wing (F-16XL-1) Flight Flow Physics with CFD Predictions at Subsonic and Transonic Speeds

The CFD modeling used has produced reasonably good global upper-surface pressure coefficient comparisons with measured flight data at both transonic and subsonic speeds at the angles of attack presented. Boundary layer comparisons showed the profiles to be reasonably well predicted inboard and under the primary vortex system. However, the secondary vortex profile was not well predicted either at the anticipated separation point or under the secondary vortex. Moreover, the flight data showed there to be a vortex/boundary-layer interaction that occurred in the vicinity of the secondary vortex. The spanwise distribution of local skin friction measured data was reasonably well predicted, especially away from the wing leading-edge. Lastly, predicted and measured flight-pressures, as well as flight-image data, for the F-16XL-1 airplane are now available via the World Wide Web.

Lamar, John E.↗
NASA NTRS1992

Dilatation-dissipation corrections for advanced turbulence models

This paper analyzes dilatation-dissipation based compressibility corrections for advanced turbulence models. Numerical computations verify that the dilatation-dissipation corrections devised by Sarkar and Zeman greatly improve both the k-omega and k-epsilon model predicted effect of Mach number on spreading rate. However, computations with the k-gamma model also show that the Sarkar/Zeman terms cause an undesired reduction in skin friction for the compressible flat-plate boundary layer. A perturbation solution for the compressible wall layer shows that the Sarkar and Zeman terms reduce the effective von Karman constant in the law of the wall. This is the source of the inaccurate k-gamma model skin-friction predictions for the flat-plate boundary layer. The perturbation solution also shows that the k-epsilon model has an inherent flaw for compressible boundary layers that is not compensated for by the dilatation-dissipation corrections. A compressibility modification for k-gamma and k-epsilon models is proposed that is similar to those of Sarkar and Zeman. The new compressibility term permits accurate predictions for the compressible mixing layer, flat-plate boundary layer, and a shock separated flow with the same values for all closure coefficients.

Wilcox, David C.↗
NASA NTRS1974

Boundary-layer transition and displacement thickness effects on zero-lift drag of a series of power-law bodies at Mach 6

Wave and skin-friction drag have been numerically calculated for a series of power-law bodies at a Mach number of 6 and Reynolds numbers, based on body length, from 1.5 million to 9.5 million. Pressure distributions were computed on the nose by the inverse method and on the body by the method of characteristics. These pressure distributions and the measured locations of boundary-layer transition were used in a nonsimilar-boundary-layer program to determine viscous effects. A coupled iterative approach between the boundary-layer and pressure-distribution programs was used to account for boundary-layer displacement-thickness effects. The calculated-drag coefficients compared well with previously obtained experimental data.

Ashby, G. C., Jr.↗
NASA NTRS2013

AMELIA CESTOL Test: Acoustic Characteristics of Circulation Control Wing with Leading- and Trailing-Edge Slot Blowing

The AMELIA Cruise-Efficient Short Take-off and Landing (CESTOL) configuration concept was developed to meet future requirements of reduced field length, noise, and fuel burn by researchers at Cal Poly, San Luis Obispo and Georgia Tech Research Institute under sponsorship by the NASA Fundamental Aeronautics Program (FAP), Subsonic Fixed Wing Project. The novel configuration includes leading- and trailing-edge circulation control wing (CCW), over-wing podded turbine propulsion simulation (TPS). Extensive aerodynamic measurements of forces, surfaces pressures, and wing surface skin friction measurements were recently measured over a wide range of test conditions in the Arnold Engineering Development Center(AEDC) National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Ft Wind Tunnel. Acoustic measurements of the model were also acquired for each configuration with 7 fixed microphones on a line under the left wing, and with a 48-element, 40-inch diameter phased microphone array under the right wing. This presentation will discuss acoustic characteristics of the CCW system for a variety of tunnel speeds (0 to 120 kts), model configurations (leading edge(LE) and/or trailing-edge(TE) slot blowing, and orientations (incidence and yaw) based on acoustic measurements acquired concurrently with the aerodynamic measurements. The flow coefficient, Cmu= mVSLOT/qSW varied from 0 to 0.88 at 40 kts, and from 0 to 0.15 at 120 kts. Here m is the slot mass flow rate, VSLOT is the slot exit velocity, q is dynamic pressure, and SW is wing surface area. Directivities at selected 1/3 octave bands will be compared with comparable measurements of a 2-D wing at GTRI, as will as microphone array near-field measurements of the right wing at maximum flow rate. The presentation will include discussion of acoustic sensor calibrations as well as characterization of the wind tunnel background noise environment.

Horne, William C.↗
NASA NTRSDate not supplied

Design Exploration of a Transonic Cruise Slotted Airfoil

A knowledge-based aerodynamic design method, CDISC, has been leveraged for the computational design exploration of the cruise slotted airfoil as a drag-saving technology for single aisle, transonic transport aircraft. Aerodynamic predictions were generated using the NASA USM3D Reynolds-averaged Navier-Stokes flow solver, and laminar flow assessments were conducted using the NASA BLSTA3D boundary layer profile solver paired with the LASTRAC stability analysis and transition prediction software. The CDISC design method was used to parametrically vary several slotted-airfoil design variables to understand their impact on aerodynamic performance. In addition to establishing best practices for slotted airfoil design, it was observed that the historically noted skin-friction penalty for cruise slotted airfoils was attributed to the low-Reynolds-number boundary layer of the flap. At cruise, this skin-friction penalty negated any potential decrease in pressure drag enabled by the cruise slotted airfoil architecture. This observation led to the development of an Aft-Laminar Multi-element Airfoil concept that uses airfoil shaping to promote natural laminar flow on the flap. At cruise conditions, the concept is predicted to offer a 2.7% reduction in sectional drag relative to a fully turbulent supercritical airfoil. Off-design analyses showed that laminar flow could be maintained with near-cruise variations in angle of attack and Mach number, resulting in sustained aerodynamic efficiency improvements and a delay in the drag rise Mach number. A low-speed, high-lift analysis at takeoff conditions predicted a maximum lift coefficient of 2.4 could be achieved by use of a variable-camber leading edge on the main element and simple deflection of the flap. These computationally-predicted benefits have motivated future research toward an aft-laminar cruise slotted wing design as an incremental step toward the application of natural laminar flow technology on transonic commercial transports.

Brett R Hiller↗
NASA NTRS1959

A Simple Method for Determining Heat Transfer, Skin Friction, and Boundary-Layer Thickness for Hypersonic Laminar Boundary-Layer Flows in a Pressure Gradient

A procedure based on the method of similar solutions is presented by which the skin friction, heat transfer, and boundary-layer thickness in a laminar hypersonic flow with pressure gradient may be rapidly evaluated if the pressure distribution is known. This solution, which at present is. restricted to power-law variations of pressure with surface distance, is presented for a wide range of exponents in the power law corresponding to both favorable and adverse pressure gradients. This theory has been compared to results from heat-transfer experiments on blunt-nose flat plates and a hemisphere cylinder at free-stream Mach numbers of 4 and 6.8. The flat-plate experiments included tests made at a Mach number of 6.8 over a range of angle of attack of +/- 10 deg. Reasonable agreement of the experimental and theoretical heat-transfer coefficients has been obtained as well as good correlation of the experimental results over the entire range of angle of attack studied. A similar comparison of theory with experiment was not feasible for boundary-layer-thickness data; however, the hypersonic similarity theory was found to account satisfactorily for the variation in boundary-layer thickness due to local pressure distribution for several sets of measurements.

Bertram, Mitchel H.↗
NASA NTRS1989

Test techniques for cryogenic wind tunnels

Some of the testing techniques developed for transonic cryogenic tunnels are presented. Techniques are emphasized which required special development or were unique because of the opportunities offered by cryogenic operation. Measuring the static aerodynamic coefficients normally used to determine component efficiency is discussed. The first topic is testing of two dimensional airfoils at transonic Mach numbers and flight values of Reynolds number. Three dimensional tests of complete configurations and sidewall mounted wings are also described. Since flight Reynolds numbers are of interest, free transition must be allowed. A discussion is given of wind tunnel and model construction effects on transition location. Time dependent phenomena, fluid mechanics, and measurement techniques are examined. The time dependent, or unsteady, aerodynamic test techniques described include testing for flutter, buffet, and oscillating airfoil characteristics. In describing non-intrusive laser techniques, discussions are given regarding optical access, seeding, forward scatter lasers, two-spot lasers, and laser holography. Methods of detecting transition and separation are reported and a new type of skin friction balance is described.

Lawing, Pierce L.↗
NASA NTRS1989

Feasibility of generating an artificial burst in a turbulent boundary layer, phase 2

Various drag accounts for about half of the total drag on commercial aircraft at subsonic cruise conditions. Two avenues are available to achieve drag reduction: either laminar flow control or turbulence manipulation. The present research deals with the latter approach. The primary objective of Phase 2 research was to investigate experimentally the feasibility of substantially reducing the skin-friction drag in a turbulent boundary layer. The method combines the beneficial effects of suction and a longitudinally ribbed surface. At a sufficiently large spanwise separation, the streamwise grooves act as a nucleation site causing a focusing of low-speed streaks over the peaks. Suction is then applied intermittently through longitudinal slots located at selected locations along those peaks to obliterate the low-speed regions and to prevent bursting. Phase 2 research was divided into two tasks. In the first, selective suction from a single streamwise slot was used to eliminate either a single burst-like event or a periodic train of artificially generated bursts in laminar and turbulent boundary layers that develop on a flat plate towed in a water channel. The results indicate that equivalent values of the suction coefficient as low as 0.0006 were sufficient to eliminate the artificially generated bursts in a laminar boundary layer.

Gad-El-hak, Mohamed↗
NASA NTRS1922

Skin frictional resistance of plane surfaces in air

Given here is the most recent research on skin frictional resistance of plane surfaces in air that was conducted by Dr. Wieselsberger under the direction of Dr. Prandtl of Gottingen University. In all, 16 models were tested. These were divided into four groups, as follows: 1) cloth, in the original condition; 2) cloth, with the nap singed off; 3) cloth, with three coats of dope; and 4) cloth, with six coats of dope. Each group consisted of four models of uniform width, 1 meter, and of lengths of 0.5, 1.0, 1.5, and 2.0 meters. Tests were made on each model at speeds varying from 7.0 to 50 meters per second. The observed total resistance was corrected for the form resistance which was obtained from the pressure distribution on the end of the model. Previous tests had shown that the form resistance due to the rounded front edge used on the models was negligible. The results are expressed in terms of the absolute coefficient of frictionless resistance, C(sub F).

Diehl, W S↗