Search NASA⌕ Search

SEARCH · Search NASA

Results for “soil testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Parameters Impacting Columnated Granular Soil Pneumatic Seal Performance

The ability of a column of loose granular soil to form a pneumatic seal was investigated by varying the diameter of the soil column, the effective column height, and the level of compaction in the soil. The data generated by this test campaign is intended to inform the design of various volatiles-extracting regolith reactor systems by investigating the viability of sealing system inlets using the soil hopper and feed tube without the use of any mechanical valves. This ‘soil column seal’ concept could be applied regardless of reactor geometry or process. Initial data was collected in ambient lab conditions using both GRC-1 and OB-1a regolith simulants. This data is intended to serve as a baseline –no attempt has been made yet to begin optimizing column parameters to achieve highest possible ∆𝑃.

Jack Stewart↗

A test of ecological optimality for semiarid vegetation

Three ecological optimality hypotheses which have utility in parameter reduction and estimation in a climate-soil-vegetation water balance model are reviewed and tested. The first hypothesis involves short term optimization of vegetative canopy density through equilibrium soil moisture maximization. The second hypothesis involves vegetation type selection again through soil moisture maximization, and the third involves soil genesis through plant induced modification of soil hydraulic properties to values which result in a maximum rate of biomass productivity.

Salvucci, Guido D.↗

Using Numerical Modeling to Simulate Space Capsule Ground Landings

Experimental work is being conducted at the National Aeronautics and Space Administration s (NASA) Langley Research Center (LaRC) to investigate ground landing capabilities of the Orion crew exploration vehicle (CEV). The Orion capsule is NASA s replacement for the Space Shuttle. The Orion capsule will service the International Space Station and be used for future space missions to the Moon and to Mars. To evaluate the feasibility of Orion ground landings, a series of capsule impact tests are being performed at the NASA Langley Landing and Impact Research Facility (LandIR). The experimental results derived at LandIR provide means to validate and calibrate nonlinear dynamic finite element models, which are also being developed during this study. Because of the high cost and time involvement intrinsic to full-scale testing, numerical simulations are favored over experimental work. Subsequent to a numerical model validated by actual test responses, impact simulations will be conducted to study multiple impact scenarios not practical to test. Twenty-one swing tests using the LandIR gantry were conducted during the June 07 through October 07 time period to evaluate the Orion s impact response. Results for two capsule initial pitch angles, 0deg and -15deg , along with their computer simulations using LS-DYNA are presented in this article. A soil-vehicle friction coefficient of 0.45 was determined by comparing the test stopping distance with computer simulations. In addition, soil modeling accuracy is presented by comparing vertical penetrometer impact tests with computer simulations for the soil model used during the swing tests.

Heymsfield, Ernie↗

L-band radar sensing of soil moisture

The performance of an L-band, 25 cm wavelength imaging synthetic aperture radar was assessed for soil moisture determination, and the temporal variability of radar returns from a number of agricultural fields was studied. A series of three overflights was accomplished over an agricultural test site in Kern County, California. Soil moisture samples were collected from bare fields at nine sites at depths of 0-2, 2-5, 5-15, and 15-30 cm. These gravimetric measurements were converted to percent of field capacity for correlation to the radar return signal. The initial signal film was optically correlated and scanned to produce image data numbers. These numbers were then converted to relative return power by linear interpolation of the noise power wedge which was introduced in 5 dB steps into the original signal film before and after each data run. Results of correlations between the relative return power and percent of field capacity (FC) demonstrate that the relative return power from this imaging radar system is responsive to the amount of soil moisture in bare fields. The signal returned from dry (15% FC) and wet (130% FC) fields where furrowing is parallel to the radar beam differs by about 10 dB.

Chang, A. T. C.↗

Polarimetric Radar Observations of Forest State for Determination of Ecosystem Processes

The objectives of this research are to test the hypotheses that ecologically significant forest state parameters may be estimated from SAR data. These include estimation of above ground biomass, plant water status, and near surface soil moisture under certain forest conditions. Test hypotheses in the northern hardwoods forest community, refine them if necessary, and establish techniques for retrieving this information from orbital SARs such as SIR-C/X-SAR. This report summarizes (1) recent progress, (2) significant results and (3) research plans concerning SIR-C/X-SAR research.

Ulaby, Fawwaz T.↗

Assessment of radar resolution requirements for soil moisture estimation from simulated satellite imagery

Radar simulations were performed at five-day intervals over a twenty-day period and used to estimate soil moisture from a generalized algorithm requiring only received power and the mean elevation of a test site near Lawrence, Kansas. The results demonstrate that the soil moisture of about 90% of the 20-m by 20-m pixel elements can be predicted with an accuracy of + or - 20% of field capacity within relatively flat agricultural portions of the test site. Radar resolutions of 93 m by 100 m with 23 looks or coarser gave the best results, largely because of the effects of signal fading. For the distribution of land cover categories, soils, and elevation in the test site, very coarse radar resolutions of 1 km by 1 km and 2.6 km by 3.1 km gave the best results for wet moisture conditions while a finer resolution of 93 m by 100 m was found to yield superior results for dry to moist soil conditions.

Ulaby, F. T.↗

Wash Solution Bath Life Extension for the Space Shuttle Rocket Motor Aqueous Cleaning System

A spray-in-air aqueous cleaning system, which replaced 1,1,1 trichloroethane (TCA) vapor degreasing, is used for critical cleaning of Space Shuttle Redesigned Solid Rocket Motor (RSRM) metal parts. Small-scale testing demonstrated that the alkaline-based wash solution possesses adequate soil loading and cleaning properties. However, full-scale testing exhibited unexpected depletion of some primary components of the wash solution. Specifically, there was a significant decrease in the concentration of sodium metasilicate which forced change-out of the wash solution after eight days. Extension of wash solution bath life was necessary to ease the burden of frequent change-out on manufacturing. A laboratory study supports a depletion mechanism that is initiated by the hydrolysis of sodium tripolyphosphate (STPP) lowering the pH of the solution. The decrease in pH causes polymerization and subsequent precipitation of sodium metasilicate (SM). Further investigation showed that maintaining the pH was the key to preventing the precipitation of the sodium metasilicate. Implementation to the full scale operation demonstrated that periodic additions of potassium hydroxide (KOH) extended the useful bath life to more than four months.

Saunders, Chad↗

Passive microwave sensing of soil moisture content - The effects of soil bulk density and surface roughness

Microwave radiometric measurements over bare fields of different surface roughness were made at frequencies of 1.4 GHz, 5 GHz, and 10.7 GHz to study the frequency dependence, as well as the possible time variation, of surface roughness. An increase in surface roughness was found to increase the brightness temperature of soils and reduce the slope of regression between brightness temperature and soil moisture content. The frequency dependence of the surface roughness effect was relatively weak when compared with that of the vegetation effect. Radiometric time-series observations over a given field indicate that field surface roughness might gradually diminish with time, especially after a rainfall or irrigation. The variation of surface roughness increases the uncertainty of remote soil moisture estimates by microwave radiometry. Three years of radiometric measurements over a test site revealed a possible inconsistency in the soil bulk density determination, which is an important factor in the interpretation of radiometric data.

Wang, J. R.↗

Passive microwave sensing of soil moisture content: Soil bulk density and surface roughness

Microwave radiometric measurements over bare fields of different surface roughnesses were made at the frequencies of 1.4 GHz, 5 GHz, and 10.7 GHz to study the frequency dependence as well as the possible time variation of surface roughness. The presence of surface roughness was found to increase the brightness temperature of soils and reduce the slope of regression between brightness temperature and soil moisture content. The frequency dependence of the surface roughness effect was relatively weak when compared with that of the vegetation effect. Radiometric time series observation over a given field indicated that field surface roughness might gradually diminish with time, especially after a rainfall or irrigation. This time variation of surface roughness served to enhance the uncertainty in remote soil moisture estimate by microwave radiometry. Three years of radiometric measurements over a test site revealed a possible inconsistency in the soil bulk density determination, which turned out to be an important factor in the interpretation of radiometric data.

Wang, J. R.↗

On Soil Moisture Retrieval and Target Decomposition

In an earlier study, an empirical model was developed to infer soil moisture and surface roughness from radar data. The inversion technique was extensively tested over bare surfaces by comparing the estimated soil moisture to in situ measurements. The overall root mean square (RMS) error in the soil moisture estimate was found to be about 3.5% and the RMS error in the RMS height estimate was less than 0.35 cm absolute for bare or slightly vegetated surfaces. However, inversion results indicate that significant amounts of vegetation cause the algorithm to underestimate soil moisture and overestimate RMS height. Among the areas over which the inversion cannot be applied, the areas with intermediate vegetation cover are of particular interest as both the vegetation and the underlying bare surface affect the backscatter. This paper concentrates mostly on these areas. Using the full polarimetric information and the Cloude target decomposition approach, three different components of the target backscattering can be isolated. One of these three components can be identified as the surface component in the case of intermediate vegetation cover. Once the surface component of the scattering is isolated, the bare surface inversion can then be applied.

Dubois, Pascale C.↗

On Soil Moisture Retrieval and Target Decomposition

In an earlier study, an empirical model was developed to infer soil moisture and surface roughness from radar data. The inversion technique was extensively tested over bare surfaces by comparing the estimated soil moisture to in situ measurements. The overall RMS error in the soil moisture estimate was found to be 3.5% and the RMS error in the RMS height estimate was less than 0.35 cm absolute for bare or slightly vegetated surfaces. However, inversion results indicate that significant amounts of vegetation cause the algorithm to underestimate soil moisture and overestimate RMS height. Among the areas over which the inversion cannot be applied, the areas with intermediate vegetation cover are of particular interest as both the vegetation and the underlying bare surface affect the backscatter. This paper concentrates mostly on these areas. Using the full polarimetric information and the Cloude target decomposition approach. Three different components of the target backscattering can be isolated. One of these three components can be identified as the surface component in the case of intermediate vegetation cover. Once the surface component of the scattering is isolated, the bare surface inversion can then be applied.

Dubois, Pascale C.↗

A New Model of Size-graded Soil Veneer on the Lunar Surface

Introduction. We propose a new model of distribution of submillimeter sized lunar soil grains on the lunar surface. We propose that in the uppermost millimeter or two of the lunar surface, soil-grains are size graded with the finest nanoscale dust on top and larger micron-scale particles below. This standard state is perturbed by ejecta deposition of larger grains at the lunar surface, which have a coating of dusty layer that may not have substrates of intermediate sizes. Distribution of solar wind elements (SWE), agglutinates, vapor deposited nanophase Fe0 in size fractions of lunar soils and ir spectra of size fractions of lunar soils are compatible with this model. A direct test of this model requires bringing back glue-impregnated tubes of lunar soil samples to be dissected and examined on Earth.

Basu, Abhijit↗

Hycrest crested wheatgrass accelerates the degradation of pentachlorophenol in soil

We investigated the effects of vegetation on the fate of pentachlorophenol (PCP) in soil using a novel high-flow sealed test system. Pentachlorophenol has been widely used as a wood preservative, and this highly toxic biocide contaminates soil and ground water at many sites. Although plants are known to accelerate the rates of degradation of certain soil contaminants, this approach has not been thoroughly investigated for PCP. The fate of [14C]PCP, added to soil at a concentration of 100 mg/kg, was compared in three unplanted and three planted systems. The plant used was Hycrest, a perennial, drought-tolerant cultivar of crested wheatgrass [Agropyron desertorum (Fischer ex Link) Schultes]. The flow-through test system allowed us to maintain a budget for 14C-label as well as monitor mineralization (breakdown to 14CO2) and volatilization of the test compound in a 155-d trial. In the unplanted systems, an average of 88% of the total radiolabel remained in the soil and leachate and only 6% was mineralized. In the planted system, 33% of the radiolabel remained in the soil plus leachate, 22% was mineralized, and 36% was associated with plant tissue (21% with the root fraction and 15% with shoots). Mineralization rates were 23.1 mg PCP mineralized kg-1 soil in 20 wk in the planted system, and for the unplanted system 6.6 mg PCP kg-1 soil for the same time period. Similar amounts of volatile organic material were generated in the two systems (1.5%). Results indicated that establishing crested wheatgrass on PCP-contaminated surface soils may accelerate the removal of the contaminant.

Non-NASA Center↗

L-band radar sensing of soil moisture

The objectives of the experiment were to assess the performance of an L-band, 25-cm wavelength imaging synthetic aperture radar (SAR) for soil moisture determination, and to study the temporal variability of radar returns from a number of agricultural fields. A series of overflights was accomplished during March 1977 over an agricultural test site in Kern County, Calif. Soil moisture samples were collected from bare fields at nine sites at depths of 0-2, 2-5, 5-15, and 15-30 cm. These gravimetric measurements were converted to percent of field capacity for correlation to the radar return signal. The initial signal film was optically correlated and scanned to produce image data numbers. These numbers were then converted to relative return power by linear interpolation of the noise power wedge which was introduced in 5-dB steps into the original signal film before and after each data run. Results of correlations between the relative return power and percent of field capacity demonstrate that the relative return power from this imaging radar system is responsive to the amount of soil moisture in bare fields. The signal returned from dry and wet fields where furrowing is parallel to the radar beam differs by about 15 dB. Before this technique can be operationally employed, adequate calibration of the radar system is required to insure comparability of data both from area to area within a single flight and between different flights.

Chang, A. T. C.↗

Aircraft scatterometer observations of soil moisture on rangeland watersheds

Extensive studies conducted by several researchers using truck-mounted active microwave sensors have shown the sensitivity of these sensors to soil moisture variations. The logical extension of these results is the evaluation of similar systems at lower resolutions typical of operational systems. Data collected during a series of aircraft flights in 1978 and 1980 over four rangeland watersheds located near Chickasha, Oklahoma, were analyzed in this study. These data included scatterometer measurements made at 1.6 and 4.75 GHz using a NASA aircraft and ground observations of soil moisture for a wide range of moisture conditions. Data were analyzed for consistency and compared to previous truck and aircraft results. Results indicate that the sensor system is capable of providing consistent estimates of soil moisture under the conditions tested.

Jackson, T. J.↗

Remote detection of geobotanical anomalies associated with hydrocarbon microseepage

As part of the continuing study of the Lost River, West Virginia NASA/Geosat Test Case Site, an extensive soil gas survey of the site was conducted during the summer of 1983. This soil gas survey has identified an order of magnitude methane, ethane, propane, and butane anomaly that is precisely coincident with the linear maple anomaly reported previously. This and other maple anomalies were previously suggested to be indicative of anaerobic soil conditions associated with hydrocarbon microseepage. In vitro studies support the view that anomalous distributions of native tree species tolerant of anaerobic soil conditions may be useful indicators of methane microseepage in heavily vegetated areas of the United States characterized by deciduous forest cover. Remote sensing systems which allow discrimination and mapping of native tree species and/or species associations will provide the exploration community with a means of identifying vegetation distributional anomalies indicative of microseepage.

Rock, B. N.↗