Search NASA⌕ Search

SEARCH · Search NASA

Results for “structure factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Unexpected Nonlinear Effects in Superconducting Transition-Edge Sensors

When a normal metal transitions into the superconducting state the DC resistance drops from a finite value to zero over some finite transition width in temperature, current, and magnetic field. Superconducting transition-edge sensors (TESs) operate within this transition region and uses resistive changes to measure deposited thermal energy. This resistive transition is not perfectly smooth and a wide range of TES designs and materials show sub-structure in the resistive transition (as seen in smooth nonmonotonic behavior, jump discontinuities, and hysteresis in the devices current-voltage relation and derivatives of the resistance with respect to temperature, bias current, and magnetic field). TES technology has advanced to the point where for many applications this structure is the limiting factor in performance and optimization consists of finding operating points away from these structures. For example, operating at or near this structure can lead to nonlinearity in the detectors response and gain scale, limit the spectral range of the detector by limiting the usable resistive range, and degrade energy resolution. The origin of much of this substructure is unknown. This presentation investigates a number of possible sources in turn. First we model the TES as a superconducting weak-link and solve for the characteristic differential equations current and voltage time dependence. We find:(1) measured DC biased current-voltage relationship is the time-average of a much higher frequency limit cycle solution.(2) We calculate the fundamental frequency and estimate the power radiated from the TES treating the bias leads as an antennae.(3) The solution for a set of circuit parameters becomes multivalued leading to current transitions between levels.(4)The circuit parameters can change the measure resistance and mask the true critical current. As a consequence the TES resistance surface is not just a function of temperature, current, and magnetic field but is also a function of the circuit elements (such as shunt resistor, SQUID inductance, and capacitor values). In other words, same device measured in different electrical circuits will have a different resistive surface in temperature, current, and magnetic field. Next we consider that at the transition temperature of a superconductor both the magnetic penetration depth and coherence length are divergent. As a consequence these important characteristic length scales are changing with operating point. We present measurements on devices showing commensurate behavior between these characteristic lengths and the length scale of added normal metal structures. Reordering of proximity vortices leads to discontinuities and irreversibility of the current-voltage curves. Last we consider a weak-link TES including both thermal activated resistance effects and the effect of the magnetic penetration depth being a function of temperature and magnetic field. We derive its impact on the resistive transition surface and the important device parameters a and b.

Superconducting Detectors↗
NASA NTRS1993

(abstract) Mechanism of Selective Porosification at Heterojunctions in Group IV Multilayer Structures

Highly selective porosification of SiGe or Ge layers is observed in multilayer Si/SiGe or Si/Ge structures grown on (100)Si. These alternating porous/nonporous structures could potentially be used to fabricate light-emitting devices. The etch-selectivity appears to be dominated by band-structure effects and other factors such as lattice strain and electrochemical potential differences play a minor role. Additional structures and electrolytic etching are being examined to confirm these results.

porosification silicon Si Ge germanium light emitt↗
NASA NTRS2024

Test and Analysis of the 8-foot Diameter Cylindrical Sandwich Composite Test Article CTA8.2B: As part of the NASA Engineering and Safety Center Shell Buckling Knockdown Factor Project

The buckling response of thin-walled cylindrical structures have long been shown to be sensitive to various imperfections. That is, imperfections related to load introduction, boundary conditions, material property variation, and geometric deviations can all contribute to experimentally obtained buckling loads being lower than the buckling loads predicted for perfect representations of the same thin-walled cylindrical structure. To account for the influence of geometry-based imperfections of a thin-walled cylindrical structure on buckling response, a design factor (also known as a buckling knockdown factor) is used during the design phase. Guidelines for buckling knockdown factors are readily available in NASA SP-8007, Buckling of Thin Walled Circular Cylinders, which was updated in 2020. Prior to this recent update, NASA SP-8007 had not been updated since 1969, and since that time, computational analysis, experimental testing, and manufacturing methods have significantly improved. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF, NESC Assessment 07-010-E) had the goal of developing buckling design recommendations for select classes of metallic and composite launch-vehicle structures [3]. Specifically, the test and analysis results from the fourth SBKF composite test article SBKF-P3-CYL-CTA8.2B, which is referred to as CTA8.2B, are described in this paper. This test was the fourth in a series of four tests on sandwich composite cylinders that will be used to experimentally validate analysis methods, which in turn can be used to develop new analysis-based shell buckling design guidelines for typical sandwich composite launch vehicle cylindrical structures. Publications describing previous test validation with analysis are available in Refs. CTA8.2B was designed to occupy one corner of the design space with approximately equal bending stiffnesses in the axial and transverse directions and have a larger ratio of radius to effective shell thickness. Each test article had a unique design and was designed to occupy a specific region of the design space. CTA8.2B was an 8-foot diameter honeycomb-core sandwich cylinder that was fabricated and tested at the NASA Marshall Space Flight Center (MSFC). The primary objectives of this test were to interrogate the structural capability of a composite test article, and to verify the test article design and analysis approach for cylinders subjected to axial compression and combined axial and bending loads. First, descriptions of the test article design and test are given in Section 2.0, and modeling and analysis methods used in support of the test article design and testing activities are described briefly in Section 3.0. Then, select test results are presented and compared to predicted results in Section 4.0, and concluding remarks are presented in Section 5.0. Finally, drawings of CTA8.2B and references used to support the test and analysis are provided in the Appendix.

Nonlinear analysis↗
NASA NTRS2006

Structural Requirements for the Space Propulsion Engine Systems

In January 2004, the National Aeronautics and Space Administration (NASA) was given a vision for Space Exploration by President Bush, setting our sight on a bold new path to go back to the Moon, then to Mars and beyond. As NASA gets ready to meet the vision set by President Bush, failures are not an option. Reliability of the propulsion engine systems will play an important role in establishing an overall safe and reliable operation of these new space systems. A new standard, NASA-STD-5012, Strength and Life Assessment for Space Propulsion System Engines, has been developed to provide structural requirements for assessment of the propulsion systems engine. This standard is a complement to the current NASA-wide standard NASA-STD-5001, Structural Design and Test Factors of Safety for Spaceflight Hardware, which excluded the requirement for the engine systems (rotatory structures) along with pressure vessels. As developed, this document builds on the heritage of the multiple industrial standards related to strength and life assessment of the structures. For assuring a safe and reliable operation of a product and/or mission, establishing a set of structural assessment requirements is a key ingredient. Hence, a concentrated effort was made to improve the requirements where there are known lessons learned during the design, test, and operation phases of the Space Shuttle Main Engine (SSME) and other engine development programs. Requirements delineated in this standard are also applicable for the reusable and/or human missions. It shall be noted that "reliability of a system cannot be tested and inspected but can only be achieved if it is first designed into a system." Hence, these strength and life assessment requirements for the space propulsion system engines shall be used along with other good engineering practices, requirements, and policies.

Aggarwal, Pravin K.↗
NASA NTRS1997

Peptide Folding and Translocation Across the Water-Membrane Interface

The ability of small peptides to organize at aqueous interfaces was examined by performing a series of large-scale, molecular dynamics computer simulations of several peptides composed of two amino acids, nonpolar leucine (L) and polar glutamine (Q). The peptides differed in size and sequence of the amino acids. Studies on dipeptides LL, LQ, QL and QQ were extended to two heptamers, LQQLLQL and LQLQLQL, designed to maximize interfacial stability of an alpha-helix and a beta-strand, respectively, by exposing polar side chains to water and nonpolar side chains to a nonpolar phase. Finally, a transition of an undecamer, composed entirely of leucine residues, from a disordered structure in water to an alpha-helix in a nonpolar phase representing the interior of the membrane was investigated. Complete folding of a peptide in solution was accomplished for the first time in computer simulations. The simulations revealed several basic principles governing the sequence-dependent organization of peptides at interfaces. Short peptides tend to accumulate at interfaces and acquire ordered structures, providing that they have a proper sequence of polar and nonpolar amino acids. The dominant factor determining the interfacial structure of peptides is the hydrophobic effect, which is manifested at aqueous interfaces as a tendency for polar and nonpolar groups of the solute to segregate into the aqueous and nonpolar phases, respectively. If peptides consist of nonpolar residue's only, they become inserted into the nonpolar phase. As demonstrated by the example of the leucine undecamer, such peptides fold into an alpha-helix as they partition into the nonpolar medium. The folding proceeds through an intermediate, called 3-10-helix, which remains in equilibrium with the alpha-helix. Once in the nonpolar environment, the peptides can readily change their orientation with respect to the interface from parallel to perpendicular, especially in response to local electric fields. The ability of nonpolar peptides to modify both the structure and orientation with respect to the interface from parallel to perpendicular, especially in response to local electric fields. The ability of nonpolar peptides to modify both the structure and orientation with changing external conditions may have provided a simple mechanism of transmitting signals from the environment to the interior of a cell.

Pohorille, Andrew↗
NASA NTRS1992

Multivariable frequency domain identification via 2-norm minimization

The author develops a computational approach to multivariable frequency domain identification, based on 2-norm minimization. In particular, a Gauss-Newton (GN) iteration is developed to minimize the 2-norm of the error between frequency domain data and a matrix fraction transfer function estimate. To improve the global performance of the optimization algorithm, the GN iteration is initialized using the solution to a particular sequentially reweighted least squares problem, denoted as the SK iteration. The least squares problems which arise from both the SK and GN iterations are shown to involve sparse matrices with identical block structure. A sparse matrix QR factorization method is developed to exploit the special block structure, and to efficiently compute the least squares solution. A numerical example involving the identification of a multiple-input multiple-output (MIMO) plant having 286 unknown parameters is given to illustrate the effectiveness of the algorithm.

Bayard, David S.↗
NASA NTRS2009

Loss Factor Estimation Using the Impulse Response Decay Method on a Stiffened Structure

High-frequency vibroacoustic modeling is typically performed using energy-based techniques such as Statistical Energy Analysis (SEA). Energy models require an estimate of the internal damping loss factor. Unfortunately, the loss factor is difficult to estimate analytically, and experimental methods such as the power injection method can require extensive measurements over the structure of interest. This paper discusses the implications of estimating damping loss factors using the impulse response decay method (IRDM) from a limited set of response measurements. An automated procedure for implementing IRDM is described and then evaluated using data from a finite element model of a stiffened, curved panel. Estimated loss factors are compared with loss factors computed using a power injection method and a manual curve fit. The paper discusses the sensitivity of the IRDM loss factor estimates to damping of connected subsystems and the number and location of points in the measurement ensemble.

Cabell, Randolph↗
NASA NTRS2015

An Analytical Solution for Yaw Maneuver Optimization on the International Space Station and Other Orbiting Space Vehicles

This paper suggests a new method for optimizing yaw maneuvers on the International Space Station (ISS). Yaw rotations are the most common large maneuvers on the ISS often used for docking and undocking operations, as well as for other activities. When maneuver optimization is used, large maneuvers, which were performed on thrusters, could be performed either using control moment gyroscopes (CMG), or with significantly reduced thruster firings. Maneuver optimization helps to save expensive propellant and reduce structural loads ‐ an important factor for the ISS service life. In addition, optimized maneuvers reduce contamination of the critical elements of the vehicle structure, such as solar arrays. This paper presents an analytical solution for optimizing yaw attitude maneuvers. Equations describing pitch and roll motion needed to counteract the major torques during a yaw maneuver are obtained. A yaw rate profile is proposed. Also the paper describes the physical basis of the suggested optimization approach. In the obtained optimized case, the torques are significantly reduced. This torque reduction was compared to the existing optimization method which utilizes the computational solution. It was shown that the attitude profiles and the torque reduction have a good match for these two methods of optimization. The simulations using the ISS flight software showed similar propellant consumption for both methods. The analytical solution proposed in this paper has major benefits with respect to computational approach. In contrast to the current computational solution, which only can be calculated on the ground, the analytical solution does not require extensive computational resources, and can be implemented in the onboard software, thus, making the maneuver execution automatic. The automatic maneuver significantly simplifies the operations and, if necessary, allows to perform a maneuver without communication with the ground. It also reduces the probability of command errors. The suggested analytical solution provides a new method of maneuver optimization which is less complicated, automatic and more universal. A maneuver optimization approach, presented in this paper, can be used not only for the ISS, but for other orbiting space vehicles.

Dobrinskaya, Tatiana↗
NASA NTRS1992

Collapse analysis of a waffle plate strongback for Space Station Freedom

The structural integrity was studied of the Integrated Equipment Assembly (IEA) Strongback of the SSF for the launch environment. The strongback structure supports the electrical power system for SSF. To achieve minimum launch mass, it is essential that flight structures are designed as light as possible. A nonlinear structural analysis was conducted to determine the collapse load of the structure and the associated factor of safety against the service loads. A modeling technique is provided for simulating the load conditions and the buckling and post buckling (collapse) load is evaluated of the IEA Strongback structure, using the finite element computer code MARC. Two of four strongback panels were modeled and analyzed. The effects were examined of the following factors on the global behavior of the strongback panels: (1) load simplification and simulation; (2) type of support boundary conditions; and (3) the possibility of weight reduction of the original structure. For this purpose, several models of the two panels of the strongback were considered. The stress level and distribution in the panels for launch condition, the Eigenvalue critical buckling load and/or the collapse load were determined.

Monasa, Frank F.↗
NASA NTRS2002

Partial Wave Analysis of Coupled Photonic Structures

The very high quality factors sustained by microcavity optical resonators are relevant to applications in wavelength filtering, routing, switching, modulation, and multiplexing/demultiplexing. Increases in the density of photonic elements require that attention be paid to how electromagnetic (EM) coupling modifies their optical properties. This is especially true when cavity resonances are involved, in which case, their characteristics may be fundamentally altered. Understanding the optical properties of microcavities that are near or in contact with photonic elements---such as other microcavities, nanostructures, couplers, and substrates---can be expected to advance our understanding of the roles that these structures may play in VLSI photonics, biosensors and similar device technologies. Wc present results from recent theoretical studies of the effects of inter- and intracavity coupling on optical resonances in compound spherical particles. Concentrically stratified spheres and bispheres constituted from homogeneous and stratified spheres are subjects of this investigation. A new formulation is introduced for the absorption of light in an arbitrary layer of a multilayered sphere, which is based on multiple reflections of the spherical partial waves of the Lorenz-Mie solution for scattering by a sphere. Absorption efficiencies, which can be used to profile cavity resonances and to infer fluorescence yields or the onset of nonlinear optical processes in the microcavities, are presented. Splitting of resonances in these multisphere systems is paid particular attention, and consequences for photonic device development and possible performance enhancements through carefully designed architectures that exploit EM coupling are considered.

Fuller, Kirk A.↗
NASA NTRS1990

Quasi-coherent structures in the turbulent boundary layer. I - Status report on a community-wide summary of the data

A review is presented of the approach, motivation and early results of a reevaluation of the knowledge collected by the research community during thirty years of research on the structure of turbulent boundary layers. Four distinctions or criteria concerning the need to improve the practices in this field are discussed: data versus inferences, possible versus actual versus significant events, one structure versus many, and one or two flows versus the totality of data. Attention given to the known quasi-coherent structures show that three factors significantly reduce the information available from laboratory data as a basis for forming a complete model of the quasi-coherent structure in the turbulent boundary layer: (1) the necessity to ensemble average probe output with resulting loss of phase information, (2) the inability to see more than one or two of the various types of structures simultaneously, and (3) the inability to see the spatial relations between the various quasi-coherent structures resulting from (1) and (2).

Kline, S. J.↗
NASA NTRS1994

Tensor-GMRES method for large sparse systems of nonlinear equations

This paper introduces a tensor-Krylov method, the tensor-GMRES method, for large sparse systems of nonlinear equations. This method is a coupling of tensor model formation and solution techniques for nonlinear equations with Krylov subspace projection techniques for unsymmetric systems of linear equations. Traditional tensor methods for nonlinear equations are based on a quadratic model of the nonlinear function, a standard linear model augmented by a simple second order term. These methods are shown to be significantly more efficient than standard methods both on nonsingular problems and on problems where the Jacobian matrix at the solution is singular. A major disadvantage of the traditional tensor methods is that the solution of the tensor model requires the factorization of the Jacobian matrix, which may not be suitable for problems where the Jacobian matrix is large and has a 'bad' sparsity structure for an efficient factorization. We overcome this difficulty by forming and solving the tensor model using an extension of a Newton-GMRES scheme. Like traditional tensor methods, we show that the new tensor method has significant computational advantages over the analogous Newton counterpart. Consistent with Krylov subspace based methods, the new tensor method does not depend on the factorization of the Jacobian matrix. As a matter of fact, the Jacobian matrix is never needed explicitly.

Feng, Dan↗
NASA NTRS1982

Three-dimensional simulations of cumulus congestus clouds on GATE day 261

Schlesinger's (1978) three-dimensional cumulus model is applied to showering congestus clouds on day 261 of GATE. Model results are compared with each other and with observations to analyze the effects of varying shear and altered sounding. Relationships between shear, mesovortices and dynamic entrainment are examined, as well as the model clouds' impact on the environment as a function of shear. The simulations appear to resemble reality in many important aspects. Altostratus layers observed on day 261 are found to be a by-product of convection in three-dimensional shear. Rapid erosion of cloud base to 3.6 km is related to the ambient thermal structure, with wind shear and initial perturbation playing a secondary role. Some of the apparent conflict regarding lateral versus cloud-top entrainment is clarified, as well as some factors governing convective downdraft structure and intensity.

Simpson, J.↗
NASA NTRS1967

Inflatable structures in space

Material composition, weight, size, and unfolding factors entering into design of inflatable space station structures

Glukharev, A.↗
NASA NTRS1987

A theoretical study of the lifetime and transport of large ionospheric density structures

A three-dimensional time-dependent ionospheric model was used to study the spatial and temporal evolution and transport of large-scale high-density ionospheric structures for a range of solar cycle, seasonal, and IMF conditions. Both density depletions and enhancements were considered. It was found that, depending on the IMF, horizontal plasma convection can cause an initial structure to break up into multiple structures of various sizes, to become stretched into elongated segments, or to remain as a single distorted structure. The lifetime of an F-region density structure depends on several factors, including its magnitude, the initial location where it was formed, the season, the solar cycle, and the convection pattern. For example, in summer, the effects of a large density structure can disappear in a few hours or last as long as nine hours, while in winter the effects can persist for 24 hours. The passage of perturbed plasma flux tubes through sunlit and auroral regions can significantly increase the lifetime of plasma enhancements.

Schunk, R. W.↗
NASA NTRS1994

A new approach to estimating rainwater content by radar using propagation differential phase shift

As microwaves propagate through rain, the rate of phase change with increasing distance is different depending upon whether the transmissions are polarized horizontally or vertically. This rate of change is the so-called specific propagation differential phase shift phi(sub DP). This paper demonstrates that at several frequencies and over a wide domain the ratio of phi(sub DP) to the rainwater content W is nearly linearly related to D(sub m), the mass-weighted mean drop size. An investigation of errors indicates that this new approach is likely to yield more accurate estimates of W than the other classical reflectivity factor Z, attenuation, or polarization techniques. The most accurate estimates of W are most likely at the highest frequency considered, 13.80 GHz. In lieu of such high-frequency measurements, these somewhat esoteric results are made more concrete through an analysis of 3-GHz radar measurements collected during the Convection and Precipitation Experiment in a tropical rainstorm in Florida. Among the principal advantages of using phi(sub DP) to measure rain are that an absolute calibration of the radar is no longer required and the estimates are decoupled from measurements of the radar reflectivity factor. Consequently, temporal and spatial structures of rain estimates do not simply mimic those of the reflectivity factor, as happens for classical estimation techniques using Z.

Jameson, A. R.↗
NASA NTRS1996

Communication and Organization in Software Development: An Empirical Study

The empirical study described in this paper addresses the issue of communication among members of a software development organization. The independent variables are various attributes of organizational structure. The dependent variable is the effort spent on sharing information which is required by the software development process in use. The research questions upon which the study is based ask whether or not these attributes of organizational structure have an effect on the amount of communication effort expended. In addition, there are a number of blocking variables which have been identified. These are used to account for factors other than organizational structure which may have an effect on communication effort. The study uses both quantitative and qualitative methods for data collection and analysis. These methods include participant observation, structured interviews, and graphical data presentation. The results of this study indicate that several attributes of organizational structure do affect communication effort, but not in a simple, straightforward way. In particular, the distances between communicators in the reporting structure of the organization, as well as in the physical layout of offices, affects how quickly they can share needed information, especially during meetings. These results provide a better understanding of how organizational structure helps or hinders communication in software development.

Seaman, Carolyn B.↗