SEARCH · Search NASA

Results for “surface acoustic waves”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS1994

Use of acoustic wave travel-time measurements to probe the near-surface layers of the Sun

The variation of solar p-mode travel times with cyclic frequency nu is shown to provide information on both the radial variation of the acoustic potential and the depth of the effective source of the oscillations. Observed travel-time data for waves with frequency lower than the acoustic cutoff frequency for the solar atmosphere (approximately equals 5.5 mHz) are inverted to yield the local acoustic cutoff frequency nu(sub c) as a function of depth in the outer convection zone and lower atmosphere of the Sun. The data for waves with nu greater than 5.5 mHz are used to show that the source of the p-mode oscillations lies approximately 100 km beneath the base of the photosphere. This depth is deeper than that determined using a standard mixing-length calculation.

Jefferies, S. M.↗

DOE OSTI2025

Infrasonic directivity of monopole, dipole and bipole ground-surface reflected sources

Infrasound (acoustic waves below 20 Hz) can be used to detect, locate and quantify activity in the atmosphere such as volcanic eruptions and anthropogenic explosions. Attempts to quantify volcanic eruption parameters such as exit velocity, plume height and mass flow rate using infrasound data depend strongly on assumptions of the acoustic source type. Infrasonic sources may produce omnidirectional or directional wavefields, while propagation effects, such as interaction with topography, can induce further wavefield directivity that is measured by field instrumentation. Limited sampling of these wavefields can hinder our ability to infer the underlying source, and thus our understanding of the eruption characteristics. Equivalent sources are often used to represent acoustic source mechanisms and resultant wavefields. In this study, we review equivalent acoustic sources as they pertain to infrasonic scale and wavelengths commonly encountered in very local (⁠<5 km range) geophysical field deployments. We highlight the equivalent infrasonic bipole source that can be induced by ground-reflection of an elevated monopole; we are not aware of any prior infrasound studies that use the bipole source concept. We use analytical and numerical methods to explore source directivity of monopole, dipole and bipole ground-reflected sources at infrasonic frequencies as well as the additional directivity complications introduced by interactions with topography. We illustrate that for typical volcano-infrasound wavelengths, increasing height above the ground as well as increasing source frequency leads to increased wavefield directivity. Numerical modelling using a simple omnidirectional monopole source embedded in topography further illustrates that both horizontal and vertical infrasound directionality can be induced by topography at the distance scales appropriate for local volcano infrasound monitoring. Information summarized in this analytical and numerical exploration of infrasound directivity may be used to help guide future volcano-infrasound field deployments intended to estimate source parameters or quantify wavefield directivity. Analytic solutions for simple whole-space or half-space atmospheres provide useful formulations for planning or initially analysing geophysical field-scale experimental data; however, especially at very local distances from the source (⁠<5 km), 3-D simulations are necessary to account for complex topography commonly encountered in volcano-infrasound applications.

Infrasound↗

NASA NTRS1985

Scattering of acoustic waves into Tollmien-Schlichting waves by small streamwise variations in surface geometry

By using the triple-deck scaling of Stewartson (1969) and Messiter (1970) it is shown that small but relatively sudden surface geometry variations that produce only very weak static pressure variations can nevertheless produce strong, i.e. O(1), coupling between an externally imposed acoustic disturbance and a spatially growing Tollmien-Schlichting wave. The analysis provides a qualitative explanation of the Leehey and Shapiro (1979) boundary-layer receptivity measurements and is in good quantitative agreement with the Aizin and Poliakov (1979) experiment. It may also explain why small 'trip wires' can promote early transition.

Goldstein, M. E.↗

NASA NTRS1986

Surface generation and detection of coupled fiber-matrix mode acoustic wave propagation in fiber-reinforced composites

A technique is described that makes it possible to transmit and receive bulk ultrasonic waves launched from the same surface of a composite sheet by means of transducers mounted on variable angle blocks. A straightforward approach to measure the velocity and attenuation of this wave is presented. A bulk compressional wave of 930,000 cm/sec velocity was launched and received in this manner in an 8-ply unidirectional T-300-5208 epoxy composite. Preliminary results indicate that parameters associated with this wave might be sensitive to accumulated damage in a composite; thus, the technique has a potential for NDE in structures made from composite materials.

Yost, W. T.↗

NASA NTRS1993

Drop dynamics in space and interference with acoustic field (M-15)

The objective of the experiment is to study contactless positioning of liquid drops, excitation of capillary waves on the surface of acoustically levitated liquid drops, and deformation of liquid drops by means of acoustic radiation pressure. Contactless positioning technologies are very important in space materials processing because the melt is processed without contacting the wall of a crucible which can easily contaminate the melt specifically for high melting temperatures and chemically reactive materials. Among the contactless positioning technologies, an acoustic technology is especially important for materials unsusceptible to electromagnetic fields such as glasses and ceramics. The shape of a levitated liquid drop in the weightless condition is determined by its surface tension and the internal and external pressure distribution. If the surface temperature is constant and there exist neither internal nor external pressure perturbations, the levitated liquid drop forms a shape of perfect sphere. If temperature gradients on the surface and internal or external pressure perturbations exist, the liquid drop forms various modes of shapes with proper vibrations. A rotating liquid drop was specifically studied not only as a classical problem of theoretical mechanics to describe the shapes of the planets of the solar system, as well as their arrangement, but it is also more a contemporary problem of modern non-linear mechanics. In the experiment, we are expecting to observe various shapes of a liquid drop such as cocoon, tri-lobed, tetropod, multi-lobed, and doughnut.

Yamanaka, Tatsuo↗

NASA NTRS1987

Application of sound and temperature to control boundary-layer transition

The growth and decay of a wave packet convecting in a boundary layer over a concave-convex surface and its active control by localized surface heating are studied numerically using direct computations of the Navier-Stokes equations. The resulting sound radiations are computed using linearized Euler equations with the pressure from the Navier-Stokes solution as a time-dependent boundary condition. It is shown that on the concave portion the amplitude of the wave packet increases and its bandwidth broadens while on the convex portion some of the components in the packet are stabilized. The pressure field decays exponentially away from the surface and then algebraically, exhibiting a decay characteristic of acoustic waves in two dimensions. The far-field acoustic behavior exhibits a super-directivity type of behavior with a beaming downstream. Active control by surface heating is shown to reduce the growth of the wave packet but have little effect on acoustic far field behavior for the cases considered. Active control by sound emanating from the surface of an airfoil in the vicinity of the leading edge is experimentally investigated. The purpose is to control the separated region at high angles of attack. The results show that injection of sound at shedding frequency of the flow is effective in an increase of lift and reduction of drag.

Maestrello, Lucio↗

NASA NTRS1990

Transition control of instability waves over a flexible surface in the presence of an acoustic field

Experimental results are presented which demonstrate the coupling of a laminar boundary layer flow with a typical flexible aircraft panel. It is shown that the boundary layer induces plate oscillations which, in turn, perturb the flow at the same frequencies. This feedback mechanism is an inherent property of laminar boundary layer flow passing over a flexible plate. As a result, the flexibility of the plate becomes a source of early transition. The laminar boundary layer at the leading edge of the plate reacts to small, upstream, unsteady disturbances due to a streamwise pressure gradient. The experiments demonstrate that a nominal sound pressure incident at the leading edge triggers early transition. It is shown that transition can be delayed by activating a heat source at the leading edge of the plate which results in downstream cooling.

Maestrello, L.↗

NASA NTRS1979

The influence of sweep on the aerodynamic loading of an oscillating NACA 0012 airfoil. Volume 1: Technical report

Aerodynamic experiments were performed on an oscillating NACA 0012 airfoil utilizing a tunnel-spanning wing in both unswept and 30 degree swept configurations. The airfoil was tested in steady state and in oscillatory pitch about the quarter chord. The unsteady aerodynamic loading was measured using pressure transducers along the chord. Numerical integrations of the unsteady pressure transducer responses were used to compute the normal force, chord force, and moment components of the induced loading. The effects of sweep on the induced aerodynamic load response was examined. For the range of parameters tested, it was found that sweeping the airfoil tends to delay the onset of dynamic stall. Sweeping was also found to reduce the magnitude of the unsteady load variation about the mean response. It was determined that at mean incidence angles greater than 9 degrees, sweep tends to reduce the stability margin of the NACA 0012 airfoil; however, for all cases tested, the airfoil was found to be stable in pure pitch. Turbulent eddies were found to convect downstream above the upper surface and generate forward-moving acoustic waves at the trailing edge which move upstream along the lower surface.

St.hilaire, A. O.↗

NASA NTRS2001

The Action of Pressure-Radiation Forces on Pulsating Vapor Bubbles

The action of pressure-radiation (or Bjerknes) forces on gas bubbles is well understood. This paper studies the analogous phenomenon for vapor bubbles, about which much less is known. A possible practical application is the removal of boiling bubbles from the neighborhood of a heated surface in the case of a downward facing surface or in the absence of gravity. For this reason, the case of a bubble near a plane rigid surface is considered in detail. It is shown that, when the acoustic wave fronts are parallel to the surface, the bubble remains trapped due to secondary Bjerknes force caused by an "image bubble." When the wave fronts are perpendicular to the surface, on the other hand, the bubble can be made to slide laterally.

Hao, Y.↗

NASA NTRS1974

Considerations on the acoustic energy radiated by toothed gears

A mechano-acoustic model is reported for calculating acoustic energy radiated by a working gear. According to this model, a gear is an acoustic coublet formed of the two wheels. The wheel teeth generate cylindrical acoustic waves while the front surfaces of the teeth behave like vibrating pistons. Theoretical results are checked experimentally and good agreement is obtained with open gears. The experiments show that the air noise effect is negligible as compared with the structural noise transmitted to the gear box.

Popinceanu, N. G.↗

NASA NTRS1988

Controlled sample orientation and rotation in an acoustic levitator

A system is described for use with acoustic levitators, which can prevent rotation of a levitated object or control its orientation and/or rotation. The acoustic field is made nonsymmetrical about the axis of the levitator, to produce an orienting torque that resists sample rotation. In one system, a perturbating reflector is located on one side of the axis of the levitator, at a location near the levitated object. In another system, the main reflector surface towards which incoming acoustic waves are directed is nonsymmetrically curved about the axis of the levitator. The levitated object can be reoriented or rotated in a controlled manner by repositioning the reflector producing the nonsymmetry.

Martin B Barmatz↗

NASA NTRS2001

Deep-Focusing Time-Distance Helioseismology

Much progress has been made by measuring the travel times of solar acoustic waves from a central surface location to points at equal arc distance away. Depth information is obtained from the range of arc distances examined, with the larger distances revealing the deeper layers. This method we will call surface-focusing, as the common point, or focus, is at the surface. To obtain a clearer picture of the subsurface region, it would, no doubt, be better to focus on points below the surface. Our first attempt to do this used the ray theory to pick surface location pairs that would focus on a particular subsurface point. This is not the ideal procedure, as Born approximation kernels suggest that this focus should have zero sensitivity to sound speed inhomogeneities. However, the sensitivity is concentrated below the surface in a much better way than the old surface-focusing method, and so we expect the deep-focusing method to be more sensitive. A large sunspot group was studied by both methods. Inversions based on both methods will be compared.

Duvall, T. L., Jr.↗

NASA NTRS1972

Excitation of Love waves in a thin film layer by a line source.

The excitation of a Love surface wave guided by a thin film layer deposited on a semiinfinite substrate is studied in this paper. Both the thin film and the substrate are considered to be elastically isotropic. Amplitudes of the surface wave in the thin film region and the substrate are found in terms of the strength of a line source vibrating in a direction transverse to the propagating wave. In addition to the surface wave, the bulk shear wave excited by the source is also studied. Analytical expressions for the bulk wave amplitude as a function of the direction of propagation, the acoustic powers transported by the surface and bulk waves, and the efficiency of surface wave excitation are obtained. A numerical example is given to show how the bulk wave radiation pattern depends upon the source frequency, the film thickness and other important parameters of the problem. The efficiency of surface wave excitation is also calculated for various parameter values.

Tuan, H.-S.↗

NASA NTRS1995

Acoustic receptivity due to weak surface inhomogeneities in adverse pressure gradient boundary layers

The boundary layer receptivity to free-stream acoustic waves in the presence of localized surface disturbances is studied for the case of incompressible Falkner-Skan flows with adverse pressure gradients. These boundary layers are unstable to both viscous and inviscid (i.e., inflectional) modes, and the finite Reynolds number extension of the Goldstein-Ruban theory provides a convenient method to compare the efficiency of the localized receptivity processes in these two cases. The value of the efficiency function related to the receptivity caused by localized distortions in surface geometry is relatively insensitive to the type of instability mechanism, provided that the same reference length scale is used to normalize the efficiency function for each type of instability. In contrast, when the receptivity is induced by variations in wall suction velocity or in wall admittance distribution, the magnitudes of the related efficiency functions, as well as the resulting coupling coefficients, are smaller for inflectional (i.e., Rayleigh) modes than for the viscous Tollmien-Schlichting waves. The reduced levels of receptivity can be attributed mainly to the shorter wavelengths and higher frequencies of the inflectional modes. Because the most critical band of frequencies shifts toward higher values, the overall efficiency of the wall suction- and the wall admittance-induced receptivity decreases with an increase in the adverse pressure gradient.

Choudhari, Meelan↗

NASA NTRS1994

Acoustic receptivity of compressible boundary layers: Receptivity by way of surface-temperature variations

The Goldstein-Ruban theory has been extended within the framework of Zavol'skii et al. to study the acoustic receptivity of compressible boundary layers. We consider the receptivity produced in a region of localized, small-amplitude variation in the surface temperature and compare it with the receptivity that is induced through a similar mechanism by a variation in the suction velocity at the surface. It is found that the orientation of the acoustic wave can have a significant impact on the receptivity process, with the maximum receptivity at a given sound-pressure level being produced by upstream oriented acoustic waves. At sufficiently low Mach numbers, the variation of receptivity with the acoustic-wave orientation can be predicted analytically and is the same for both surface suction and surface heating. However, as a result of the acoustic refraction across the mean boundary layer, the above dependence can become rather complex and, also, dependent on the type of surface nonuniformity. The results also suggest that the receptivity caused by temperature nonuniformities may turn out to be more significant than that produced by the mean-flow perturbations associated with strip suction.

Choudhari, Meelan↗

NASA NTRS1998

Measurement of Nonlinear Receptivity to Surface Irregularities

Acoustic receptivity is the process by which acoustic disturbances are internalized into the shear layer to generate instability waves. Experiments have shown that, when tuned to the eigenvalue modes, the amplitude of the resulting T-S waves scales with the acoustic field intensity. When a surface irregularity is present, the characteristic wall wavenumber forces a spatial mode onto the near-wall mean velocity field, thus providing modal length scales comparable to those of T-S waves. In this experiment an attempt was made to increase the acoustic receptivity by exciting a difference mode via a quadratic interaction between two larger-wavenumber, forced modes. The difference mode is tuned to the dominant T-S eigenmode wavenumber. As expected, an increased receptivity corresponding to the difference mode was measured downstream of branch I, suggesting the presence of the nonlinearity.

Davila-Acaron, Jose B.↗

NASA NTRS1987

Double-Referenced, Pulsed, Phase-Locked Loop - DRP2L2

System allows precise measurement of phase shift between two toneburst signals initially derived from same periodic source but delayed by different amounts through either path-length differences, propagation velocity differences, or both. Used to measure accurately phase shift encountered by acoustic wave striking front and back surfaces of sample. Velocity known, resulting measurement is of sample thickness. Thickness known, measurement is of sound velocity. Technique applies to many sources of radiation and not limited to acoustics.

Heyman, J. S.↗

NASA NTRS1994

Reduction of blade-vortex interaction noise through porous leading edge

The effect of the porous leading edge of an airfoil on the blade-vortex interaction noise, which dominates the far-field acoustic spectrum of the helicopter, is investigated. The thin-layer Navier-Stokes equations are solved with a high-order upwind-biased scheme and a multizonal grid system. The Baldwin-Lomax turbulence model is modified for considering transpiration on the surface. The amplitudes of the propagating acoustic wave in the near field are calculated directly from the computation. The porosity effect on the surface is modeled in two ways: (1) imposition of prescribed transpiration velocity distribution and (2) calculation of transpiration velocity distribution by Darcy's law. Results show leading-edge transpiration can suppress pressure fluctuations at the leading edge during blade-vortex interaction and consequently reduce the amplitude of propagating noise by 30% at a maximum in the near field.

Lee, Soogab↗