Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermodynamic analyses”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Energetics of oxidation and formation of uranium mononitride

Uranium mononitride (UN) is an advanced nuclear fuel currently being considered for use in several generation IV fast and thermal neutron spectrum core designs, with additional applications to thermal and electric nuclear propulsion reactors. Here, to better understand the thermal behavior and thermodynamic stability of UN, we investigated the bulk thermal oxidation process and thermochemical reactions, including the enthalpy of oxidation and standard enthalpy of formation, by conducting thermalgravimetric analysis – differential scanning calorimetry coupled with mass spectrometry (TGA-DSC-MS), and high temperature transposed temperature drop and oxide melt drop solution calorimetry. The bulk oxidation of UN (containing a small amount of α-UN 1.5+x ) in air was found to follow a step-wise process characterized by consecutive oxidative reactions UN-UN 1.5+x -UO 2 → UO 2 -UO 3 —N k → UO 3 —N k → UO 3 → U 3 O 8 . TGA results support that the UO 2 – U 2 N 3+x passivating layer delays the onset of rapid bulk oxidation of UN in air up to 662 K. Synchrotron X-ray diffraction (XRD) and extended X-ray absorption fine structure (EXAFS) analyses were performed to characterize UN and its final oxidized product. The standard enthalpy of formation (ΔH° f ) of UN was determined to be –144.4 ± 5.9 kJ/mol·atom, in good agreement with previously determined values from Pt encapsulation and bomb calorimetric experiments. Lastly, a negative linear correlation between ΔH° f and the N/U molar ratio was established based on the thermochemical data obtained in this work and previously reported enthalpies of formations of β-UN 1.5-x and α-UN 1.5+x .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Initial Assessment of TeF 6 Adsorption

Research and development that supports the management of off-gases from nuclear fuel reprocessing has historically been focused on the off-gas streams that arise from aqueous reprocessing technology. However, as Gen-IV reactor development pathways move toward deployment, alternative spent nuclear fuel (SNF) processing and disposition pathways have been considered more actively. This work is focused upon aspects of fluoride volatility (FV) processing. The versatility of this method for deployment against multiple types of spent fuel encourages the continued advancement of both the primary separations processes and the secondary processes, including waste treatment, material control and accountability, and engineering designs. Recent work noted that TeF 6 , the most highly volatile fluorinated compound produced during FV processing, did not have a clear abatement technology recommended in the literature. Thus, this work performed scoping tests on activated alumina and copper shot to assess whether they could be used to remove TeF 6 from gas streams that bear F 2 . Previous work on this topic was not well described in the literature and was not performed with excess F 2 in the stream as would be typical of spent fuel processing via FV. To support an understanding of the concentration of TeF 6 contacting the adsorbent beds, a series of preliminary testing identified the TeF 6 production rate and the equilibrium concentration of TeF 6 in the gas stream contacting the adsorbent. Excess F 2 was determined to not affect the ability of activated alumina to remove TeF 6 from the gas stream quickly and completely. A determination of whether excess F 2 affected the distribution depth of Te in the sorbent bed is still pending analysis of the used sorbent. Literature suggests that when activated alumina is near saturation, TeF 6 could migrate from the sorbent bed. Future testing should investigate this possibility. Copper metal did not adsorb TeF 6 in the presence of F 2 across the sorbent temperature range of 50 to 335°C. F 2 was fully removed by the copper bed. Although preliminary thermodynamics would indicate adsorption to be energetically favorable, other factors that impact adsorption (e.g., slow kinetics, excess fluorine on the copper surface, an unfavorable transition state) are likely preventing the adsorption of TeF 6 at an easily measurable rate. The work also investigated TeF 6 production from multiple forms of Te in the temperature range of 100 to 250°C. No previous study had assessed the initial reaction rates for this process. A carefully designed study allowed determination of the activation energy for the production of TeF 6 from Te metal. The substantial amount of data collected during this study merits analysis beyond what is described here. A more in-depth kinetic analysis will be pursued. Additional analytical results will provide the ability to benchmark adsorption coefficients for TeF 6 , understand the distribution of TeF 6 within the alumina bed, and better understand the effect of F 2 partial pressure on Te fluorination. The data from this report, as supplemented by these additional analyses, will be submitted to a peer-reviewed journal.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Physics-Based Model to Represent Membrane-Electrode Assemblies of Solid-Oxide Fuel Cells Based on Gadolinium-Doped Ceria

This paper reports a physics-based model that predicts membrane-electrode assembly (MEA) performance of solid-oxide fuel cells (SOFCs) with Ce 0.9 Gd 0.1 O 2− δ (GDC10) electrolyte membranes. The paper derives self-consistent thermodynamic and transport properties for GDC1o mobile charged defects (oxide vacancies and reduced-ceria small polarons) by fitting published measurements of oxygen non-stoichiometry and conductivity over ranges of temperature and O 2 partial pressures. The button-cell model is applied to evaluate how mixed ionic-electronic conductivity influences the performance of an SOFC MEA with a GDC10 electrolyte sandwiched between a porous, composite Ni-GDC10 anode and a porous, composite cathode of Sm 0.5 Sr 0.5 CoO 3− δ (i.e., SSC) and GDC10. SSC properties are also derived by fitting published conductivity and oxygen non-stoichiometry measurements. Mixed conductivity of GDC10 and competing charge transfer reactions at both electrodes reduce open circuit voltages due to leakage current and buildup of defect concentrations at electrode-electrolyte interfaces. To fit polarization data, the button-cell model includes heterogeneous reaction rates for defect incorporation on the GDC10 surface along with Butler–Volmer expressions derived for competing charge transfer reaction rates from rigorous analyses assuming rate-limiting, elementary charge transfer reactions for each electrode. The calibrated MEA model can support rigorous SOFC modeling with GDC10 electrolytes over the range of conditions within a fully operating cell.

Electrochemistry↗
DOE OSTI2022

Thermal-Mechanical Analysis of an Additive Manufacturing Ceramic Heat Exchanger for High-Temperature Recuperator in a sCO2 Power System

Supercritical CO2 (sCO2) Brayton power cycle can be configured in a closed-loop power system and has a potentially high cycle efficiency. Compactness and high efficiency of a sCO2 power block make the sCO2 Brayton cycle a versatile power cycle in broad applications. While many heat sources are of sufficient intensity to produce high temperature working fluids to achieve high cycle efficiency, the thermal-mechanical stability of traditional materials (e.g., steels and nickel-based superalloys) used in construction of heat exchangers and turbine components limits the operating conditions and thus thermodynamic efficiency of the system. This effort seeks to establish the viability of ceramic heat exchanger technologies for the most extreme operating conditions envisioned for power generation and other high temperature processes. Heat exchangers constructed from ultra-high temperature ceramics, a class of extreme environment materials featuring melting points (Tmp.) above 3000 degrees C, is particularly appealing for sCO2 Brayton cycles given their ultra-low creep rates and very high retained strength at low homologous temperatures (i.e., T < 0.5 Tmp., or at least 1500 degrees C). To translate these materials properties to ultra-high temperature heat exchangers, innovations are required in ceramic manufacturing techniques to realize the complex architectures featured in compact heat exchangers with high power density. With appropriate processing, ZrB2-SiC based compositions can be sintered to near full density and shaped into complex topologies via ceramic additive manufacturing methods. This paper analyzes heat exchanger designs and explores thermal-mechanical implications of the operating environment. Thermal flow, heat transfer, and conjugate mechanical analyses provide insights into benefits and risks associated with the design approach.

additive manufacturing↗
DOE OSTI2022

Transition of Large-Scale Environmental Conditions and Characteristics of Four Rainfall Types Observed by S-PolKa During the MJO-1 Active Phase of DYNAMO/CINDY/AMIE

Analyses of National Center for Atmospheric Research (NCAR) S-PolKa dual-polarization radar data and ERA5 reanalysis fields indicate gradual changes in convection characteristics and large-scale environmental conditions during a central Indian Ocean Madden-Julian Oscillation (MJO) event observed by the DYNAMO/CINDY/AMIE field campaigns in late October 2011 (MJO-1). Examination of four rainfall types (isolated convective cores, convective, mixed, and stratiform) reveals a transition of convection characteristics (i.e., areal coverage and depth) between distinct 5-day environmental periods at the beginning and end of this ~2-week MJO active phase. A shift toward less frequent rainfall covering less of the radar domain for all four rainfall types occurs when large-scale lower-tropospheric dry air advects into the region with the westerly wind burst (WWB). Drier and warmer lower-free-tropospheric conditions associated with the WWB contribute to increased large-scale surface-based convective inhibition (CIN), surface-based convective available potential energy (CAPE), and cloud base heights. A thermodynamic budget analysis indicates reduced surface heat fluxes contribute to the increased surface-based CAPE. Greater CAPE at the end of MJO-1 coincides with deeper 50-dBZ convective echoes, while decreased 10-dBZ depth for all rainfall types corresponds in time with WWB-related dry-air advection. Increased (decreased) reflectivity values in the lower-level vertical reflectivity distribution of convective (stratiform) precipitation indicate increased (decreased) convective (stratiform) intensities when the WWB is present. The opposite depth changes for convective echoes and opposite shifts in convective and stratiform precipitation intensities underscore how the WWB can have differing impacts at different reflectivity thresholds and stages of the deep convection lifecycle.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Dependence of Deep Convective Cell Properties on Meteorological and Aerosol Conditions during TRACER

Deep convective cells significantly influence Earth’s energy balance and water cycle. However, their accurate representation in numerical models remains challenging due to their small spatiotemporal scales and limited observational constraints. This study examines over ∼400 deep convective cells near Houston, observed by a dual-polarization C-band radar during the Tracking Aerosol Convection Interactions Experiment (TRACER) intensive observation period (June–September 2022). Cells are categorized by lifetime into short-lived (<40 min), intermediate-lived (40–80 min), and long-lived (80+ min) groups. Long-lived cells were broader (∼13.2 km at 2–4-km height) and deeper (∼11.4 km) than short-lived cells (∼6.4-km width, ∼7.31-km height). Using random forest (RF) modeling and correlation analyses, precipitable water vapor (PWV), 2–6-km lapse rate, 0–8-km bulk shear, and fine aerosol mass concentration (Mass_f) are identified as key predictors of cell lifetime. Higher PWV is associated with significantly longer convective cell lifetimes compared to the low-PWV group, particularly within low 2–6-km temperature lapse rate (LR_26km), moderate-to-higher 0–8-km bulk shear (BS_08km), and low-to-moderate Mass_f environments. RF analysis also identifies low-level (0–2 km) equivalent potential temperature, PWV, Mass_f, and surface latent heat flux as key predictors for cell width and height. Short-lived cells have higher aerosol number concentrations (500–1000-nm size range), linked to onshore wind conditions and marine aerosols; however, their low concentration suggests the sensitivity may reflect associated meteorological regimes rather than a direct aerosol effect. Long-lived cells have higher concentrations of organic and sulfate aerosols, while short-lived cells exhibit higher black carbon concentrations. These results highlight the intricate dependence of convective cell lifetimes and structure on environmental moisture, thermodynamics, wind shear, and aerosol characteristics.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Preliminary Design of Nuclear Reactor Heat Delivery Systems: Integration with Reference Oil Refinery, Methanol Synthesis, and Hydrogen Production

The Department of Energy’s (DOE) Integrated Energy Systems (IES) program is generating comprehensive analyses validating the opportunity for using nuclear energy in a variety of applications including future clean grids, providing heat for direct use, and providing heat to help reduce emissions in chemical commodities. This work focuses on the preliminary designs of thermal delivery systems that can integrate heat produced from a nuclear core to industrial processes. The key research question that needs to be answered is: what is the prospective method for integrating nuclear generated heat energy into non-electric applications that can facilitate combined heat and power operations by advanced nuclear reactor systems? This research is a composition of case studies showing preliminary conceptual designs for thermal delivery systems integrating advanced nuclear systems with a few industrial systems including high temperature steam electrolysis, a reference oil refinery, and potential future methanol systems that supplant some natural gas use with nuclear energy. Piping and instrumentation diagrams have been developed to show the conceptual integration of nuclear systems with representative industrial systems. Different features of the configurations are dependent on the specific integration requirements including energy source conditions, demand quantity, and require energy application conditions. Design concepts are validated using thermodynamic balance calculations to verify system performance including calculating system losses during transport. Key components: pumps and compressors, heat exchangers, and network piping are reported with key design information and sizing.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Lanczos Algorithm, the Transfer Matrix, and the Signal-to-Noise Problem

This Letter introduces a method for determining the energy spectrum of lattice quantum chromodynamics by applying the Lanczos algorithm to the transfer matrix and using a bootstrap generalization of the Cullum-Willoughby method to filter out spurious eigenvalues. Proof-of-principle analyses of the simple harmonic oscillator and the lattice quantum chromodynamics proton mass demonstrate that this method provides faster ground-state convergence than the “effective mass,” which is related to the power-iteration algorithm. Lanczos provides more accurate energy estimates than multistate fits to correlation functions with small imaginary times while achieving comparable statistical precision. Two-sided error bounds are computed for Lanczos results and guarantee that excited-state effects cannot shift Lanczos results far outside their statistical uncertainties.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Morning boundary layer conditions for shallow to deep convective cloud evolution during the dry season in the central Amazon

Observations of the boundary layer (BL) processes are analyzed statistically for dry seasons of 2 years and in detail, as case studies, for 4 shallow convective days (ShCu) and 4 shallow-to-deep convective days (ShDeep) using a suite of ground-based measurements from the Observation and Modeling of the Green Ocean Amazon (GoAmazon 2014/5) Experiment. The BL stages in ShDeep days, from the nighttime to the cloudy mixing layer stage, are then described in comparison with ShCu days. Atmospheric thermodynamics and dynamics, environmental profiles, and surface turbulent fluxes were employed to compare these two distinct situations for each stage of the BL evolution. Particular attention is given to the morning transition stage, in which the BL changes from stable to unstable conditions in the early morning hours. Results show that the decrease in time duration of the morning transition on ShDeep days is associated with high humidity and well-established vertical wind shear patterns. Higher humidity since nighttime not only contributes to lowering the cloud base during the rapid growth of the BL but also contributes to the balance between radiative cooling and turbulent mixing during nighttime, resulting in higher sensible heat flux in the early morning. The sensible heat flux promotes rapid growth of the well-mixed layer, thus favoring the deeper BL starting from around 08:00 LST (UTC-4 h). Under these conditions, the time duration of morning transition is used to promote convection, having an important effect on the convective BL strength and leading to the formation of shallow cumulus clouds and their subsequent evolution into deep convective clouds. Statistical analysis was used to validate the conceptual model obtained from the case studies. Despite the case-to-case variability, the statistical analyses of the processes in the BL show that the described processes are very representative of cloud evolution during the dry season.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Techno-Economic Analysis of a Concentrating Solar Power Plant Using Redox-Active Metal Oxides as Heat Transfer Fluid and Storage Media

We present results for a one-dimensional quasi-steady-state thermodynamic model developed for a 111.7 MW e concentrating solar power (CSP) system using a redox-active metal oxide as the heat storage media and heat transfer agent integrated with a combined cycle air Brayton power block. In the energy charging and discharging processes, the metal oxide CaAl 0.2 Mn 0.8 O 2.9-δ (CAM28) undergoes a reversible, high temperature redox cycle including an endothermic oxygen-releasing reaction and exothermic oxygen-incorporation reaction. Concentrated solar radiation heats the redox-active oxide particles under partial vacuum to drive the reduction extent deeper for increased energy density at a fixed temperature, thereby increasing storage capacity while limiting the required on sun temperature. Direct counter-current contact of the reduced particles with compressed air from the Brayton compressor releases stored chemical and sensible energy, heating the air to 1,200°C at the turbine inlet while cooling and reoxidizing the particles. The cool oxidized particles recirculate through the solar receiver subsystem for another cycle of heating and reduction (oxygen release). We applied the techno-economic model to 1) size components, 2) examine intraday operation with varying solar insolation, 3) estimate annual performance characteristics over a simulated year, 4) estimate the levelized cost of electricity (LCOE), and 5) perform sensitivity analyses to evaluate factors that affect performance and cost. Simulations use hourly solar radiation data from Barstow, California to assess the performance of a 111.7 MW e system with solar multiples (SMs) varying from 1.2 to 2.4 and storage capacities of 6–14 h. The baseline system with 6 h storage and SM of 1.8 has a capacity factor of 54.2%, an increase from 32.3% capacity factor with no storage, and an average annual energy efficiency of 20.6%. Calculations show a system with an output of 710 GWh e net electricity per year, 12 h storage, and SM of 2.4 to have an installed cost of $329 million, and an LCOE of 5.98 ¢/kWh e . This value meets the U.S. Department of Energy’s SunShot 2020 target of 6.0 ¢/kWh e ( U. S Department of Energy, 2012 ), but falls just shy of the 5.0 ¢/kWh e 2030 CSP target for dispatchable electricity ( U. S Department of Energy, 2017 ). The cost and performance results are minimally sensitive to most design parameters. However, a one-point change in the weighted annual cost of capital from 8 to 7% (better understood as a 12.5% change) translates directly to an 11% decrease (0.66 ¢/kWhe) in the LCOE.

Gorman, Brandon T.↗
DOE OSTI2020

Consequences of product inhibition in the quantification of kinetic parameters

While the potential for product inhibition in catalytic reactions is well known, the impact of neglected inhibition on measured kinetic parameters is often overlooked. The presence of product inhibition, most often caused by the competitive adsorption of products with reactants on catalytic active sites, is difficult to determine a priori for an arbitrary catalytic system. The significance of product inhibition relies on the concentration of the products, their adsorption thermodynamics on catalytically relevant sites, and process parameters such as temperature and pressure. When inhibition is significant, however, apparent activation energies and reaction orders vary from the differential-reactor apparent activation energy by a factor of 1/(1 - δ), where δ is the total inhibition order (e.g., the factor (1 - δ) = 1.6 for a system with product inhibition of -0.6 order). This is illustrated here with the kinetics of NO oxidation over Cu ion clusters (Cu x O y ) in Cu-SSZ-13, for which the product NO 2 inhibits the forward reaction. Furthermore, in the presence of inhibition, when only reactants are fed to a flow reactor or placed in a batch reactor, there is often no practical conversion that is low enough to guarantee differential behavior. Inclusion of products in the feed solves this problem, allowing accurate determination of kinetic parameters such as apparent reaction orders and activation energies. We also demonstrate that evaluation of the necessity of co-feeding products to assure measurement of differential-reactor data in a given catalytic system is straightforward from a plot of the log of the rate (or conversion) versus the log of the space time in a flow reactor or elapsed time in a batch reactor. We encourage inclusion of this test in all kinetic analyses that are reasonably approximated by power law rate expressions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Analyses of hot/warm CO2 removal processes for IGCC power plants

Abstract Compared with a pulverized coal power plant, the integrated gasification combined cycle (IGCC) has several advantages, including, among others better environmental performance and low CO 2 capture cost. Hot/warm CO 2 removal from syngas has also been a subject of research due to its potentially higher thermal efficiency. In this study, we proposed a generic adsorption based hot/warm CO 2 removal process for IGCC power plants. Through analyses of the proposed generic process we have demonstrated that higher temperature of the hot/warm CO 2 removal process will results in larger heat of adsorption, which in turns may increase energy consumption of the process. Under most of the operating temperature range, hot/warm CO 2 removal process will lead to more electricity loss compared to the baseline Selexol process. However, if the adsorption step takes place at a temperature close to or higher than the highest steam temperature in steam cycle, our analysis indicates that the process may lead to minimal electricity loss. The study also provided some other insights into the pathways for hot/warm CO 2 removal process to improve its energy performance through process and sorbent designs. Graphical Abstract

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

TRACER-Coastal Urban Boundary-Layer Interactions with Convection (TRACER-CUBIC) Field Campaign Report

To better understand the complicated web of processes governing convective cloud life cycle and aerosol-convection interactions, the U.S. Department of Energy (DOE)’s Atmospheric Radiation Measurement (ARM) user facility supported deployment of a variety of advanced atmospheric measurement systems to the greater Houston, Texas, area from 1 October 2021 to 30 September 2022 as part of the Tracking Aerosol Convection Interactions Experiment (TRACER). Houston was selected as a study area because isolated convection and a variety of aerosol conditions are common in this region. This one-year ARM Mobile Facility (AMF) deployment featured a four-month intensive operational period (IOP) during summer 2022 (1 June–30 September). The ARM instrumentation was deployed at three sites along an east-west transect from La Porte, Texas to an ancillary site in a less-polluted rural region southwest of downtown Houston (Figure 1). At the La Porte Site, which is located near the Houston ship channel in an area that experiences significant pollution, the first ARM Mobile Facility (AMF1) was deployed. During the IOP, the ARM tethered balloon system (TBS) operated at the ancillary site. The second-generation C-Band Scanning ARM Precipitation Radar (CSAPR) operated near Pearland, Texas, roughly halfway between the Laporte and ancillary sites. As part of the TRACER- Coastal Urban Boundary-Layer Interactions with Convection (CUBIC) project, three boundary-layer profiling systems) were deployed along a north-south transect spanning from the University of Houston Coastal Center to the Aldine site north of downtown Houston (also blue dot in Figure 1) during the TRACER IOP. These systems included the National Oceanic and Atmospheric Administration (NOAA) National Severe Storms Laboratory CLAMPS2 (C2), which was deployed at the UHCC, the University of Wisconsin SPARC, which was deployed at the ARM CSAPR site near Pearland (orange diamond in middle of map in Figure 1), and the University of Oklahoma CLAMPS1 (C1), which was deployed at Aldine. These three systems have been successfully operated in various field campaigns, providing data sets that collectively offer new insights into atmospheric-boundary-layer (ABL) processes, sea-breeze (SB) circulations, and convection initiation (CI). For the TRACER IOP window, these systems ran continuously between 1 June and 26 September, 2022. Due to commitments to NOAA projects, the Doppler lidar at the UHCC site was not available until 24 June 2022. The CLAMPS and SPARC profiling systems are self-contained platforms that have benefited from several years of development and deployment. Instruments and data processing were maintained remotely, which made the 4-month deployment for the TRACER-CUBIC IOP period possible. The same basic instrument configuration comprises each system: a scanning Doppler wind lidar for flow characterization and passive profiler(s) for characterizing planetary-boundary-layer (PBL) thermodynamic properties. Each platform includes a Halo Streamline Doppler wind lidar, an Atmospheric Emitted Radiance Interferometer (AERI), and a surface meteorology station. CLAMPS1 and CLAMPS2 each also include a microwave radiometer (MWR, Figure 1d). The TRACER-CUBIC hypotheses included (i) Interactions of SB and urban circulations and how they affect the PBL structure in the Houston environment, causing spatially (horizontally and vertically) and temporally highly variable flow patterns, (ii) heat, moisture, and aerosol transport and mixing depend on these flow dynamics, and (iii) an improved understanding of the flow patterns and PBL structure are critical for investigating the processes leading to CI. To test these hypotheses, the project aimed at (i) characterizing SB circulations and their impacts on the diurnal evolution of the structure of the ABL, (ii) studying the evolution of Houston’s complex urban boundary layer, and (iii) identifying effects of urban-induced circulations on pre-convective environments. TRACER-CUBIC observations generally provide good coverage during the summer IOP. Initial screening of the data indicates a good number of cases with bay-breeze (BB) and/or SB signatures, local CI, and interesting boundary-layer features such as strong nocturnal low-level jets (LLJs, Table 1). The numbers listed in rows 3-5 in this table will be further updated as part of ongoing in-depth analyses and systematic identification of local circulations and CI events. More detailed information about the data availability and quality for each instrument is provided in the “readme” files that were submitted to the ARM Data Center along with each archived data sets. These “readme” files also provide instrument descriptions, information about the data collection and processing procedures, data formats, and any additional information relevant for further data analysis.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Amorphous Oxyhalide Matters for Achieving Lithium Superionic Conduction

The recently surged halide-based solid electrolytes (SEs) are great candidates for high-performance all-solid-state batteries (ASSBs), due to their decent ionic conductivity, wide electrochemical stability window, and good compatibility with high-voltage oxide cathodes. In contrast to the crystalline phases in halide SEs, amorphous components are rarely understood but play an important role in Li-ion conduction. Here, we reveal that the presence of amorphous component is common in halide-based SEs that are prepared via mechanochemical method. The fast Li-ion migration is found to be associated with the local chemistry of the amorphous proportion. Taking Zr-based halide SEs as an example, the amorphization process can be regulated by incorporating O, resulting in the formation of corner-sharing Zr–O/Cl polyhedrons. This structural configuration has been confirmed through X-ray absorption spectroscopy, pair distribution function analyses, and Reverse Monte Carlo modeling. The unique structure significantly reduces the energy barriers for Li-ion transport. As a result, an enhanced ionic conductivity of (1.35 ± 0.07) × 10 –3 S cm –1 at 25 °C can be achieved for amorphous Li 3 ZrCl 4 O 1.5 . In addition to the improved ionic conductivity, amorphization of Zr-based halide SEs via incorporation of O leads to good mechanical deformability and promising electrochemical performance. In conclusion, these findings provide deep insights into the rational design of desirable halide SEs for high-performance ASSBs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Evaluation of Nuclear Spent Fuel Disposal in Clay-Bearing Rock - Process Model Development and Experimental Studies

The DOE R&D program under the Spent Fuel Waste Science Technology (SFWST) campaign has made key progress in modeling and experimental approaches towards the characterization of chemical and physical phenomena that could impact the long-term safety assessment of heat-generating nuclear waste disposition in deep clay/shale/argillaceous rock. International collaboration activities such as heater tests and postmortem analysis of samples recovered from these have elucidated key information regarding changes in the engineered barrier system (EBS) material exposed to years of thermal loads. Chemical and structural analyses of sampled bentonite material from such tests has as well as experiments conducted on these are key to the characterization of thermal effects affecting bentonite clay barrier performance and the extent of sacrificial zones in the EBS during the thermal period. Thermal, hydrologic, and chemical data collected from heater tests and laboratory experiments has been used in the development, validation, and calibration of THMC simulators to model near-field coupled processes. This information leads to the development of simulation approaches (e.g., continuum vs. discrete) to tackle issues related to flow and transport at various scales of the host-rock and EBS design concept. Consideration of direct disposal of large capacity dual-purpose canisters (DPCs) as part of the back-end SNF waste disposition strategy has generated interest in improving our understanding of the effects of elevated temperatures on the EBS design. This is particularly important for backfilled repository concepts where temperature plays a key role in the EBS behavior and long-term performance. This report describes multiple R&D efforts on disposal in argillaceous geologic media through development and application of coupled THMC process models, experimental studies on clay/metal/cement barrier and host-rock (argillite) material interactions, molecular dynamic (MD) simulations of water transport during (swelling) clay dehydration, first-principles studies of metaschoepite (UO 2 corrosion product) stability, and advances in thermodynamic plus surface complexation database development. Drift-scale URL experiments provides key data for testing hydrological-chemical (HC) model involving strong couplings of fluid mixing and barrier material chemical interactions. The THM modeling focuses on heater test experiments in argillite rock and gas migration in bentonite as part of international collaboration activities at underground research laboratories (URLs). In addition, field testing at an URL involves in situ analysis of fault slip behavior and fault permeability. Pore-scale modeling of gas bubble migration is also being investigated within the gas migration modeling effort. Interaction experiments on bentonite samples from heater test under ambient and elevated temperatures permit the evaluation of ion exchange, phase stability, and mineral transformation changes that could impact clay swelling. Advances in the development, testing, and implementation of a spent nuclear fuel (SNF) degradation model coupled with canister corrosion focus on the effects of hydrogen gas generation and its integration with Geologic Disposal Safety Assessment (GDSA). GDSA integration activities includes evaluation of groundwater chemistries in shale formations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Loss and Isotopic Fractionation of Alkali Elements during Diffusion-Limited Evaporation from Molten Silicate: Theory and Experiments

Moderately volatile elements (MVEs) are variably depleted in planetary bodies, reflecting the imprints of nebular and planetary processes. Among MVEs, Na, K, and Rb are excellent tracers for unraveling the history of MVE depletion in planetary bodies because they have similar geochemical behaviors but can be chemically fractionated by evaporation and condensation processes. Furthermore, K and Rb are amenable to high-precision isotopic analyses, which can help constrain the conditions of evaporation and condensation. To quantitatively understand why Na, K, and Rb are depleted in planetary bodies, we have carried out vacuum evaporation experiments from basaltic melt at 1200 and 1400 °C to study their evaporation kinetics and isotopic fractionations. We chose this composition because it is relevant to evaporation from small differentiated planetesimals. The Rb isotopic compositions of the evaporation residues were measured by multicollector inductively coupled plasma mass spectrometry (MC-ICPMS), and the K isotopic compositions were measured along profiles across the residues by secondary ion mass spectrometry (SIMS). In the 1400 °C run products, we found that the concentrations of both K and Rb in the run products decreased from core to rim, which was accompanied by a heavy K isotope enrichment near the surface. This indicates that, in this run, evaporation was limited by diffusion. To use those data quantitatively, we derive analytical equations that describe the evaporation rate and isotopic fractionation associated with diffusion-limited evaporation from a sphere, slab, and cylinder in transient and quasi-steady state regimes. This model is used to tease out the roles that diffusive transport in the melt and evaporation at the melt/gas interface play in setting the elemental depletion and isotopic composition of the residue. Under our experimental conditions, volatility decreases in the order of Na, Rb, and K. Using our experimental results in a thermodynamic model, we have estimated the product γΓ of activity coefficients × evaporation coefficients of Na, Rb, and K. The measured isotopic compositions of the residues are well explained using Rayleigh distillations, whereby the relative volatilities of K and Rb isotopes are given by the square root of their masses. We use our results and previously published data to predict how K and Rb could have been lost as a function of temperature, melt composition, oxygen fugacity, and saturation degree relevant to Vesta’s building blocks. We find that the K and Rb depletions, K/Rb elemental fractionation, and δ 41 K and δ 87 Rb isotopic fractionations of Vesta (as sampled by howardite-eucrite-diogenite (HED) meteorites) are best explained by evaporation of submillimeter size objects for 0.1-10 years at moderate temperatures (~1050 °C) in a medium ~98.8% saturated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Incorporating the molecular-scale into a hydrodynamic description of confined aqueous systems

Hydrodynamics provides a continuum-level description of fluid motion, but its applicability at the nanoscale becomes uncertain due to the emerging importance of molecular-level effects such as spatial heterogeneity. Hydrodynamic boundary conditions that incorporate molecular details allow us to partition the system into a near-wall region and a bulk fluid region. We identify a hydrodynamic wall located inside the fluid that determines where slip begins. By extending the hydrodynamic wall with the slip length, the position of the extrapolated wall is established. This offers a unified description of both slip and stagnant flow behaviors, with wall hydrophobicity characterized by the relative location of the extrapolated wall with respect to the physical wall. Employing this concept in analyses of equilibrium molecular dynamics (MD) and non-equilibrium MD simulations of Couette and Poiseuille flows, our results demonstrate consistency between equilibrium and non-equilibrium approaches across different flow types and confinement levels. This demonstrates the robust nature of linear response theory. We then explore the effects of fluid-wall and bulk fluid interactions on the hydrodynamic properties. These findings enhance the effectiveness of molecular-based simulations for investigating complex confined systems in nanofluidics, biology, and colloidal science, offering a complementary molecular-scale perspective to traditional continuum approaches.

flow simulations↗