SEARCH · Search NASA

Results for “titanium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Use of a nitrogen-argon plasma to improve adherence of sputtered titanium carbide coatings on steel

Friction and wear experiments on 440-C steel surfaces that had been RF-sputtered with titanium carbide when a small percentage of nitrogen was added to the plasma were conducted. X-ray photoelectron spectroscopy and X-ray diffraction were used to analyze the resultant coatings. Results indicate that a small partial pressure of nitrogen (about 0.5%) markedly improves the adherence, friction, and wear properties when compared with coatings applied on sputter-etched oxidized surfaces or in the presence of a small oxygen partial pressure. The improvements are related to the formation of an interface containing a mixture of the nitrides of titanium and iron, which are harder than their corresponding oxides.

Brainard, W. A.↗

NASA NTRS1979

The distribution of titanium on the lunar surface

Titanium concentrations derived from the lunar-orbiting gamma-ray experiment on Apollo 15 and 16 by analyzing a spectral interval in which the titanium signal is relatively enhanced are presented. Landing site soil values provide the reference for a regression curve from which Ti concentrations in 137 regions of adequate counting statistics are calculated. Mare Tranquillitatis contains the highest, and Mare Crisium the lowest Ti concentration, and regional values in the western maria range from 1.1% to 4.1%. Highland Ti concentrations suggest a north-south symmetry which is not consistent with previously reported Fe and Th results. Comparisons with telescopic spectral reflectance studies of the maria do not show complete agreement and suggest that effects due to Fe may not have been fully removed from the reflectance data.

Metzger, A. E.↗

NASA NTRS1980

The titanium oxide phi system

The phy system of titanium oxide has been studied in emission in the near-infrared, with the Fourier transform spectrometer at a resolution of 8000,000. Approximately 3000 lines from 25 bands of this system have been identified, including all five 0-0 and 0-1 bands corresponding to the five natural titanium isotopes. Eleven vibrational levels have been observed, and all bands have been rotationally analyzed. Band intensities are agreement with known isotopic abundances and calculated Franck-Condon factors.

Galehouse, D. C.↗

NASA NTRS1972

Flaw growth of 6Al-4V STA titanium in nitrogen tetroxide with low nitric oxide content

The sustained load flow growth characteristics of surface flowed 6Al-4V STA titanium specimens were determined when exposed to nitrogen tetroxide N2O4 having nitric oxide (NO) concentrations of 0.06 to 0.30%. Test temperatures ranged from 70 to 150 F. It was observed that the threshold stress intensity for the titanium decreased abruptly below on NO concentration of 0.18% and also decreased as the temperature increased. The threshold stress intensity was determined to be greater than or equal to 60% of the critical stress intensity for NO concentrations of 0.18 to 0.30% and temperatures of 90 and 120 F. Sustained load tests conducted in N2O4 vapor with a 0.30% NO concentration at 120 F indicated the threshold to be also greater than or equal to 60% of critical.

Bixler, W. D.↗

NASA NTRS1983

Preventing Cracks in Titanium Rotary Seals

Titanium rubs agains plastic instead of metal in new rotary seal for cryogenic pump. Friction-induced cracks in titanium parts are thereby avoided.

Ciana, J. J.↗

NASA NTRS1982

Interrelation of material microstructure, ultrasonic factors, and fracture toughness of two phase titanium alloy

The pivotal role of an alpha-beta phase microstructure in governing fracture toughness in a titanium alloy, Ti-662, is demonstrated. The interrelation of microstructure and fracture toughness is demonstrated using ultrasonic measurement techniques originally developed for nondestructive evaluation and material property characterization. It is shown that the findings determined from ultrasonic measurements agree with conclusions based on metallurgical, metallographic, and fractographic observations concerning the importance of alpha-beta morphology in controlling fracture toughness in two phase titanium alloys.

Vary, A.↗

NASA NTRS1982

Improved damage tolerance of titanium by adhesive lamination

Basic damage tolerance properties of Ti-6A1-4V titanium plate can be improved by laminating thin sheets of titanium with adhesives. Compact tension and center cracked tension specimens made from thick plate, thin sheet, and laminated plate (six plies of thin sheet) were tested. The fracture toughness of the laminated plate was 39 percent higher than the monolithic plate. The laminated plate's through the thickness crack growth rate was about 20 percent less than that of the monolithic plate. The damage tolerance life of the surface cracked laminate was 6 to over 15 times the life of a monolithic specimen. A simple method of predicting crack growth in a crack ply of a laminate is presented.

Johnson, W. S.↗

NASA NTRS1982

Interstellar titanium abundances toward 19 high-latitude stars

The 3384 absorption line of interstellar Ti II has been observed at high resolution along lines of sight toward nine nearly aligned pairs of foreground disk and background halo stars, the latter having z-distance greater than 500 pc. The primary result is the great strength of Ti II absorption perpendicular to the plane of the Galaxy. Compared with the well-studied disk abundances, there is apparently a vertical gradient of titanium depletion above the galactic plane. The gaseous titanium abundance relative to hydrogen increases with z-distance and with LSR velocity by factors exceeding 20 and can reach nearly solar proportions.

Albert, C. E.↗

NASA NTRS1982

Long titanium heat pipes for high-temperature space radiators

Titanium heat pipes are being developed to provide light weight, reliable heat rejection devices as an alternate radiator design for the Space Reactor Power System (SP-100). The radiator design includes 360 heat pipes, each of which is 5.2 m long and dissipates 3 kW of power at 775 K. The radiator heat pipes use potassium as the working fluid, have two screen arteries for fluid return, a roughened surface distributive wicking system, and a D shaped cross section container configuration. A prototype titanium heat pipe, 5.5 m long, was fabricated and tested in space simulating conditions. Results from startup and isothermal operation tests are presented. These results are also compared to theoretical performance predictions that were used to design the heat pipe initially.

Girrens, S. P.↗

NASA NTRS1983

Fabrication and evaluation of cold/formed/weldbrazed beta-titanium skin-stiffened compression panels

The room temperature and elevated temperature buckling behavior of cold formed beta titanium hat shaped stiffeners joined by weld brazing to alpha-beta titanium skins was determined. A preliminary set of single stiffener compression panels were used to develop a data base for material and panel properties. These panels were tested at room temperature and 316 C (600 F). A final set of multistiffener compression panels were fabricated for room temperature tests by the process developed in making the single stiffener panels. The overall geometrical dimensions for the multistiffener panels were determined by the structural sizing computer code PASCO. The data presented from the panel tests include load shortening curves, local buckling strengths, and failure loads. Experimental buckling loads are compared with the buckling loads predicted by the PASCO code. Material property data obtained from tests of ASTM standard dogbone specimens are also presented.

Royster, D. M.↗

NASA NTRS1982

Superplastic forming/weld-brazing of titanium skin-stiffened compression panels

A study was conducted to exploit the processing advantages of superplastic forming and weld-brazing for the fabrication of titanium skin-stiffened structural components. Small titanium compression panels were fabricated and tested at room temperature. Stiffeners having configurations of a conventional hat shape, beaded shaped web, ribbed shaped web, or stepped shaped web were investigated. The data from the panel tests included load-shortening curves, local buckling strengths, and failure loads. Experimental buckling loads were compared with buckling loads calculated using a finite-element analysis. The superplastic formed/weld-brazed panels having complex shaped stiffeners developed from 20 to 58 percent higher local buckling strengths than panels with conventionally shaped stiffeners.

Royster, D. M.↗

NASA NTRS1982

Long titanium heat pipes for high-temperature space radiators

Titanium heat pipes are being developed to provide light weight, reliable heat rejection devices as an alternate radiator design for the Space Reactor Power System (SP-100). The radiator design includes 360 heat pipes, each of which is 5.2 m long and dissipates 3 kW of power at 775 K. The radiator heat pipes use potassium as the working fluid, have two screen arteries for fluid return, a roughened surface distributive wicking system, and a D-shaped cross-section container configuration. A prototype titanium heat pipe, 5.5-m long, has been fabricated and tested in space-simulating conditions. Results from startup and isothermal operation tests are presented. These results are also compared to theoretical performance predictions that were used to design the heat pipe initially.

Girrens, S. P.↗

NASA NTRS1983

Damage tolerance evaluation of adhesively laminated titanium

Johnson, W. S.↗

NASA NTRS1983

Low-Temperature Forming of Beta Titanium Alloys

Low cost methods for titanium structural fabrication using advanced cold-formable beta alloys were investigated for application in a Mach 2.7 supersonic cruise vehicle. This work focuses on improving processing and structural efficiencies as compared with standard hot formed and riveted construction of alpha-beta alloy sheet structure. Mechanical property data and manufacturing parameters were developed for cold forming, brazing, welding, and processing Ti-15V-3Cr-3Sn-3Al sheet, and Ti-3Al-8V-6Cr-4Zr on a more limited basis. Cost and structural benefits were assessed through the fabrication and evaluation of large structural panels. The feasibility of increasing structural efficiency of beta titanium structure by selective reinforcement with metal matrix composite was also explored.

Kaneko, R. S.↗

NASA NTRS1982

Trichite growth during oxidation of titanium and TA6V4 alloy by water vapor at high temperatures

Analysis by electron scanning microscope detected the formation of rutile trichites on the surface of specimens of titanium and titanium alloy TA6V4 oxidized in water vapor in the temperature range 650 to 950 C and the water vapor pressure range from 0.5 to 18 torr. In all specimens, two sublayers of rutile were formed: an external layer of basalt-like appearance, and a microcrystalline inner layer. Morphology of the trichites depends on temperature and the material (whether metal or alloy), but not on vapor pressure.

Coddet, C.↗

NASA NTRS1984

Effect of creep in titanium alloy Ti-6Al-4V at elevated temperature on aircraft design and flight test

Short-term compressive creep tests were conducted on three titanium alloy Ti-6Al-4V coupons at three different stress levels at a temperature of 714 K (825 F). The test data were compared to several creep laws developed from tensile creep tests of available literature. The short-term creep test data did not correlate well with any of the creep laws obtained from available literature. The creep laws themselves did not correlate well with each other. Short-term creep does not appear to be very predictable for titanium alloy Ti-6Al-4V. Aircraft events that result in extreme, but short-term temperature and stress excursions for this alloy should be approached cautiously. Extrapolations of test data and creep laws suggest a convergence toward predictability in the longer-term situation.

Jenkins, J. M.↗

NASA NTRS1986

Titanium Heat-Pipe Wicks

Sintered titanium offers several advantages over sintered aluminum as material for heat-pipe wicks. Titanium both strong and light. Thermal conductivity only one-seventh of aluminum, and therefore used when high thermal resistance is needed to prevent boiling of working fluid.

Shaubach, R.↗

NASA NTRS1985

Rapid adhesive bonding of advanced composites and titanium

Rapid adhesive bonding (RAB) concepts utilize a toroid induction technique to heat the adhesive bond line directly. This technique was used to bond titanium overlap shear specimens with 3 advanced thermoplastic adhesives and APC-2 (graphite/PEEK) composites with PEEK film. Bond strengths equivalent to standard heated-platen press bonds were produced with large reductions in process time. RAB produced very strong bonds in APC-2 adherend specimens; the APC-2 adherends were highly resistant to delamination. Thermal cycling did not significantly affect the shear strengths of RAB titanium bonds with polyimide adhesives. A simple ultrasonic non-destructive evaluation process was found promising for evaluating bond quality.

Stein, B. A.↗