Separation measurements in binary species gaseous vortex flows and flow visualization studies in a water vortex
Gaseous fission reactor propulsion - fluid dynamics, binary separation, and flow visualization studies
FLOW VISUALIZATION↗
SEARCH · Search NASA
Results for “vortex dynamics”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
CFD Analyses and Jet-Noise Predictions of Chevron Nozzles with Vortex Stabilization
The wind computational fluid dynamics code was used to perform a series of analyses on a single-flow plug nozzle with chevrons. Air was injected from tubes tangent to the nozzle outer surface at three different points along the chevron at the nozzle exit: near the chevron notch, at the chevron mid-point, and near the chevron tip. Three injection pressures were used for each injection tube location--10, 30, and 50 psig-giving injection mass flow rates of 0.1, 0.2, and 0.3 percent of the nozzle mass flow. The results showed subtle changes in the jet plume s turbulence and vorticity structure in the region immediately downstream of the nozzle exit. Distinctive patterns in the plume structure emerged from each injection location, and these became more pronounced as the injection pressure was increased. However, no significant changes in centerline velocity decay or turbulent kinetic energy were observed in the jet plume as a result of flow injection. Furthermore, computational acoustics calculations performed with the JeNo code showed no real reduction in jet noise relative to the baseline chevron nozzle.
Dippold, Vance↗
Vortex interactions and decay in aircraft wakes
The dynamic interactions of aircraft wake vortices are investigated using both inviscid and viscous models. The phenomenon of vortex merging resulting in the rapid aging of a vortex wake is examined in detail. It is shown that the redistribution of vorticity from convection and diffusion during merging is a mechanism effective in reducing the hazard of a wake. Inviscid computations show that the merging phenomenon may be sensitive to small changes in spanwise load distribution and that the fuselage vortex shed from the wing-fuselage junction can play a significant role in promoting merging of wing-tip and flap vortices. Vortex-wake-merging computations using a second-order closure model of turbulent transport indicate that a low-hazard wake occurs when the generating aircraft flap and wing-tip vortices of the same strength and sign. This optimum is achieved when the flap vortex is located outboard approximately 40% of the distance to the tip vortex.
Bilanin, A. J.↗
Shear-Layer Effects on Trailing Vortices
Crosswind shear can influence the trailing vortex trajectories significantly, according to both field measurement and numerical simulations. Point vortex models are used in this paper to study the fluid dynamic mechanism in the interactions between trailing vortex pair and shear layers. It has been shown that the shear-layer deformation causes the vortex descent history difference in the two vortices of the vortex pair. When a shear layer is below the vortex pair with the same sign as the left vortex, the right vortex descends less than the left vortex. When the same shear layer is above the vortex pair, the right vortex descends more. The descent altitudes of the two vortices are the same when they go through a constant, non-deformed shear layer. Those trends are in agreement with Navier-Stokes simulations.
Zheng, Z. C.↗
Wind-tunnel free-flight investigation of a 0.15-scale model of the F-106B airplane with vortex flaps
An investigation to determine the effects of vortex flaps on the flight dynamic characteristics of the F-106B in the area of low-speed, high-angle-of-attack flight was undertaken on a 0.15-scale model of the airplane in the Langley 30- by 60-Foot Tunnel. Static force tests, dynamic forced-oscillation tests, as well as free-flight tests were conducted to obtain a data base on the flight characteristics of the F-106B airplane with vortex flaps. Vortex flap configurations tested included a full-span gothic flap, a full-span constant-chord flap, and a part-span gothic flap.
Yip, Long P.↗
Behavior of a Polydisperse Cluster of Drops Evaporating in a Vortex
A model has been developed to describe the dynamics and evaporation of polydisperse collections of liquid drops in an axisymmetric, infinite, cylindrical vortex. This formulation is valid both in the dense regime, where interactions between particles are important, and in the dilute regime, where interactions between particles are not important. In contrast to the standard way of discretizing polydisperse collections of particles, where the initial size distribution is partitioned into a finite number of bins and these bins are fixed during the calculation, here it is only the initial size distribution which is partitioned into a finite number of sizes. Each initial size class thus defined is followed dynamically and thermodynamically in its own system of coordinates which moves with the drops. Therefore, each initial size class develops a continuum of sizes as the drops are centrifuged towards the hotter ambient and evaporate. The gas phase is followed in its own system of coordinates.
liquid evaporation liquid dispersal particle flow↗
In-flight leading-edge extension vortex flow-field survey measurements on a F-18 aircraft at high angle of attack
Flow-field measurements on the leading-edge extension (LEX) of the F-18 High Alpha Research Vehicle (HARV) were obtained using a rotating rake with 16 hemispherical-tipped five-hole probes. Detailed pressure, velocity, and flow direction data were obtained through the LEX vortex core. Data were gathered during 1-g quasi-stabilized flight conditions at angles of attack alpha from 10 degrees to 52 degrees and at Reynolds numbers based on mean aerodynamic cord up to 16 x 10(exp 6). Normalized dynamic pressures and crossflow velocities clearly showed the primary vortex above the LEX and formation of a secondary vortex at higher angles of attack. The vortex was characterized by a ring of high dynamic pressure surrounding a region of low dynamic pressure at the vortex core center. The vortex core, subcore diameter, and vertical location of the core above the LEX increased with angle of attack. Minimum values for static pressure were obtained in the vortex subcore and decreased nearly linearly with increasing angle of attack until vortex breakdown. Rake-measured static pressures were consistent with previously documented surface pressures and showed good agreement with flow visualization flight test results. Comparison of the LEX vortex flight test data to computational solutions at alpha approximately equals 19 degrees and 30 degrees showed fair correlation.
David M Richwine↗
Ignition dynamics of a laminar diffusion flame in the field of a vortex embedded in a shear flow
The role of streamwise-spanwise vorticity interactions that occur in turbulent shear flows on flame/vortex interactions is examined by means of asymptotic analysis and numerical simulation in the limit of small Mach number. An idealized model is employed to describe the interaction process. The model consists of a one-step, irreversible Arrhenius reaction between initially unmixed species occupying adjacent half-planes which are then allowed to mix and react in the presence of a streamwise vortex embedded in a shear flow. It is found that the interaction of the streamwise vortex with shear gives rise to small-scale velocity oscillations which increase in magnitude with shear strength. These oscillations give rise to regions of strong temperature gradients via viscous heating, which can lead to multiple ignition points and substantially decrease ignition times. The evolution in time of the temperature and mass-fraction fields is followed, and emphasis is placed on the ignition time and structure as a function of vortex and shear strength.
Macaraeg, Michele G.↗
Delta wing vortex manipulation using pulsed and steady blowing during ramp pitching
The effectiveness of steady and pulsed blowing as a method of controlling delta wing vortices during ramp pitching has been investigated in flow visualization experiments conducted in a water tunnel. The recessed angled spanwise blowing technique was utilized for vortex manipulation. This technique was implemented on a beveled 60 delta wing using a pair of blowing ports located beneath the vortex core at 40% chord. The flow was injected primarily in the spanwise direction but was also composed of a component normal to the wing surface. The location of vortex burst was measured as a function of blowing intensity and pulsing frequency under static conditions, and the optimum blowing case was applied at three different wing pitching rates. Experimental results have shown that, when the burst location is upstream of the blowing port, pulsed blowing delays vortex breakdown in static and dynamic cases. Dynamic tests verified the existence of a hysteresis effect and demonstrated the improvements offered by pulsed blowing over both steady blowing and no-blowing scenarios. The application of blowing, at the optimum pulsing frequency, made the vortex breakdown location comparable in static and ramp pitch-up conditions.
Moreira, J.↗
Prediction of Aerodynamic Coefficient using Genetic Algorithm Optimized Neural Network for Sparse Data
Wind tunnels use scale models to characterize aerodynamic coefficients, Wind tunnel testing can be slow and costly due to high personnel overhead and intensive power utilization. Although manual curve fitting can be done, it is highly efficient to use a neural network to define the complex relationship between variables. Numerical simulation of complex vehicles on the wide range of conditions required for flight simulation requires static and dynamic data. Static data at low Mach numbers and angles of attack may be obtained with simpler Euler codes. Static data of stalled vehicles where zones of flow separation are usually present at higher angles of attack require Navier-Stokes simulations which are costly due to the large processing time required to attain convergence. Preliminary dynamic data may be obtained with simpler methods based on correlations and vortex methods; however, accurate prediction of the dynamic coefficients requires complex and costly numerical simulations. A reliable and fast method of predicting complex aerodynamic coefficients for flight simulation I'S presented using a neural network. The training data for the neural network are derived from numerical simulations and wind-tunnel experiments. The aerodynamic coefficients are modeled as functions of the flow characteristics and the control surfaces of the vehicle. The basic coefficients of lift, drag and pitching moment are expressed as functions of angles of attack and Mach number. The modeled and training aerodynamic coefficients show good agreement. This method shows excellent potential for rapid development of aerodynamic models for flight simulation. Genetic Algorithms (GA) are used to optimize a previously built Artificial Neural Network (ANN) that reliably predicts aerodynamic coefficients. Results indicate that the GA provided an efficient method of optimizing the ANN model to predict aerodynamic coefficients. The reliability of the ANN using the GA includes prediction of aerodynamic coefficients to an accuracy of 110% . In our problem, we would like to get an optimized neural network architecture and minimum data set. This has been accomplished within 500 training cycles of a neural network. After removing training pairs (outliers), the GA has produced much better results. The neural network constructed is a feed forward neural network with a back propagation learning mechanism. The main goal has been to free the network design process from constraints of human biases, and to discover better forms of neural network architectures. The automation of the network architecture search by genetic algorithms seems to have been the best way to achieve this goal.
Rajkumar, T.↗
On the mechanism of dynamic stall.
The sequence of events comprising dynamic stall of an airfoil is discussed, with emphasis on the role of the leading edge laminar separation bubble and shed vortex. A simple bubble model, based on a combination of theoretical and experimental investigations, is used to discuss the events prior to the shedding of the vortex, and provides the basis for a heuristic estimate of the delay in the occurrence of dynamic stall on a pitching airfoil. The evidence for the existence and dominant effect of the leading edge vortex on the dynamic stall required (but in most cases not presently available) for the prediction of the effects of stall on helicopter rotor blades are discussed. It is the intention of this paper to focus attention on the laminar separation bubble and the shed leading edge vortex as the dominant features of the dynamic stall mechanism in the hope of stimulating greater emphasis on these features in future dynamic stall research.
Johnson, W.↗
Prediction of vortex breakdown on a delta wing
Recent studies of leading-edge vortex flows with computational fluid dynamics codes using Euler or Navier-Stokes formulations have shown fair agreement with experimental data. These studies have concentrated on simulating the flowfields associated with a sharp-edged flat plate 70 deg delta wing at angles of attack where vortex breakdown or burst is observed over the wing. There are, however, a number of discrepancies between the experimental data and the computed flowfields. The location of vortex breakdown in the computational solutions is seen to differ from the experimental data and to vary with changes in the computational grid and freestream Mach number. There also remain issues as to the validity of steady-state computations for cases which contain regions of unsteady flow, such as in the post-breakdown regions. As a partial response to these questions, a number of laminar Navier-Stokes solutions were examined for the 70 deg delta wing. The computed solutions are compared with an experimental database obtained at low subsonic speeds. The convergence of forces, moments and vortex breakdown locations are also analyzed to determine if the computed flowfields actually reach steady-state conditions.
Agrawal, S.↗
Unsteady evaporation and combustion of a drop cluster inside a vortex
A model has been developed which describes the evaporation, ignition and combustion of a drop cluster embedded in a large vortex. The purpose of this model is to simulate the behavior of drops in large coherent vortices produced in the shear layer of a jet. The model treats the dynamic interactions between the drops and the vortex, and also takes into account the drop proximity to calculate the heat and mass transfers between drops and ambient gas. The gas phase outside the cluster is treated as an unsteady, reacting phase, whereas quasi-steadiness is assumed between the drops and surrounding gas inside the cluster. The results show a very complex interaction between the dynamics of the drop-loaded vortex, the flame, and the evaporation process.
Fichot, F.↗
Vortex pairing in a circular jet under controlled excitation. I - General jet response. II - Coherent structure dynamics
Hot-wire and flow visualization studies were performed in three air jets subjected to pure-tone excitation. The instability, vortex roll-up, and transition to the controlled excitation were investigated. The conditions most favorable to vortex parting were determined as a function of the excitation Strouhal number, the Reynolds number, and the initial shear-layer state; it was shown that the rolled-up vortex rings undergo pairing under 'the shear layer mode', and the 'jet-column mode' when the Strouhal numbers based on the initial shear-layer momentum thickness are 0.012 and 0.85, respectively. Coherent ring-like vortical structures could be educed to the end of the potential core; however, the paired vortex becomes weaker with increasing downstream distances. The transverse transport of 'u' momentum by the coherent structures was much larger during the pairing process than in regions where a single vortex is studied.
Zaman, K. B. M. Q.↗
Wind Tunnel Investigation of Ground Wind Loads for Ares Launch Vehicle
A three year program was conducted at the NASA Langley Research Center (LaRC) Aeroelasticity Branch (AB) and Transonic Dynamics Tunnel (TDT) with the primary objective to acquire scaled steady and dynamic ground-wind loads (GWL) wind-tunnel data for rollout, on-pad stay, and on-pad launch configurations for the Ares I-X Flight Test Vehicle (FTV). The experimental effort was conducted to obtain an understanding of the coupling of aerodynamic and structural characteristics that can result in large sustained wind-induced oscillations (WIO) on such a tall and slender launch vehicle and to generate a unique database for development and evaluation of analytical methods for predicting steady and dynamic GWL, especially those caused by vortex shedding, and resulting in significant WIO. This paper summarizes the wind-tunnel test program that employed two dynamically-aeroelastically scaled GWL models based on the Ares I-X Flight Test Vehicle. The first model tested, the GWL Checkout Model (CM), was a relatively simple model with a secondary objective of restoration and development of processes and methods for design, fabrication, testing, and data analysis of a representative ground wind loads model. In addition, parametric variations in surface roughness, Reynolds number, and protuberances (on/off) were investigated to determine effects on GWL characteristics. The second windtunnel model, the Ares I-X GWL Model, was significantly more complex and representative of the Ares I-X FTV and included the addition of simplified rigid geometrically-scaled models of the Kennedy Space Center (KSC) Mobile Launch Platform (MLP) and Launch Complex 39B primary structures. Steady and dynamic base bending moment as well as model response and steady and unsteady pressure data was acquired during the testing of both models. During wind-tunnel testing of each model, flow conditions (speed and azimuth) where significant WIO occurred, were identified and thoroughly investigated. Scaled data from the Ares I-X GWL model test was used in the determination of worst-case loads for the analysis of Ares I-X FTV design wind conditions. Finally, this paper includes a brief discussion of the limited full-scale GWL data acquired during the rollout and on-pad stay of the Ares I-X FTV that was launched from KSC on October 28, 2009.
Keller, Donald F.↗
An Operational Wake Vortex Sensor Using Pulsed Coherent Lidar
NASA and FAA initiated a program in 1994 to develop methods of setting spacings for landing aircraft by incorporating information on the real-time behavior of aircraft wake vortices. The current wake separation standards were developed in the 1970's when there was relatively light airport traffic and a logical break point by which to categorize aircraft. Today's continuum of aircraft sizes and increased airport packing densities have created a need for re-evaluation of wake separation standards. The goals of this effort are to ensure that separation standards are adequate for safety and to reduce aircraft spacing for higher airport capacity. Of particular interest are the different requirements for landing under visual flight conditions and instrument flight conditions. Over the years, greater spacings have been established for instrument flight than are allowed for visual flight conditions. Preliminary studies indicate that the airline industry would save considerable money and incur fewer passenger delays if a dynamic spacing system could reduce separations at major hubs during inclement weather to the levels routinely achieved under visual flight conditions. The sensor described herein may become part of this dynamic spacing system known as the "Aircraft VOrtex Spacing System" (AVOSS) that will interface with a future air traffic control system. AVOSS will use vortex behavioral models and short-term weather prediction models in order to predict vortex behavior sufficiently into the future to allow dynamic separation standards to be generated. The wake vortex sensor will periodically provide data to validate AVOSS predictions. Feasibility of measuring wake vortices using a lidar was first demonstrated using a continuous wave (CW) system from NASA Marshall Space Flight Sensor and tested at the Volpe National Transportation Systems Center's wake vortex test site at JFK International Airport. Other applications of CW lidar for wake vortex measurement have been made more recently, including a system developed by the MIT Lincoln Laboratory. This lidar has been used for detailed measurements of wake vortex velocities in support of wake vortex model validation. The first measurements of wake vortices using a pulsed, lidar were made by Coherent Technologies, Inc. (CTI) using a 2 micron solid-state, flashlamp-pumped system operating at 5 Hz. This system was first deployed at Denver's Stapleton Airport. Pulsed lidar has been selected as the baseline technology for an operational sensor due to its longer range capability.
Barker, Ben C., Jr.↗
Development and testing of laser Doppler system components for wake vortex monitoring. Volume 1: Scanner development, laboratory and field testing and system modeling
A servo-controlled range/elevation scanner for the laser Doppler velocimeter (LDV) was developed and tested in the field to assess its performance in detecting and monitoring aircraft trailing vortices in an airport environment. The elevation scanner provides a capability to manually point the LDV telescope at operator chosen angles from 3.2 deg. to 89.6 deg within 0.2 deg, or to automatically scan the units between operator chosen limits at operator chosen rates of 0.1 Hz to 0.5 Hz. The range scanner provides a capability to manually adjust the focal point of the system from a range of 32 meters to a range of 896 meters under operator control, or to scan between operator chosen limits and at rates from 0.1 Hz to 6.9 Hz. The scanner controls are designed to allow simulataneous range and elevation scanning so as to provide finger scan patterns, arc scan patterns, and vertical line scan patterns. The development and testing of the unit is discussed, along with a fluid dynamic model of the wake vortex developed in a laser Doppler vortex sensor simulation program.
Wilson, D. J.↗
Vortex interactions and decay in aircraft wakes
The dynamic interaction of aircraft wake vortices was investigated using both inviscid and viscous models. For the viscous model, a computer code was developed using a second-order closure model of turbulent transport. The phenomenon of vortex merging which results in the rapid aging of a vortex wake was examined in detail. It was shown that the redistribution of vorticity during merging results from both convective and diffusive mechanisms.
Bilanin, A. J.↗