Results for “water table” — Page 12

NASA NTRSDate not supplied

Downwelling Far-Infrared Emission Spectra Measured by FIRST at Cerro Toco, Chile and Table Mountain Facility, CA

The Far-Infrared Spectroscopy of the Troposphere (FIRST) instrument is a fourier transform spectrometer developed to measure the far-infrared portion of the Earth's longwave spectrum. Specifically, the purpose is measurement of the important, yet under-investigated 100 to 1000 cm-1 band. Presented here are measurements made by FIRST at two successful deployments in a ground-based configuration to measure downwelling longwave radiation. The initial deployment was to Cerro Toco, Chile. FIRST operated from August to October, 2009 as part of the Radiative Heating in Underexplored Bands Campaign (RHUBC-II) campaign. After recalibration, FIRST was deployed to the Table Mountain Facility from August to October, 2012. Dry days for both campaigns were chosen for analysis ? 09/24/2009 and 10/19/2012. Also available from both deployments are coincident radiosonde temperature and water vapor vertical profiles used as inputs to radiance calculations performed by two platforms, the AER Line-by-Line Radiative Transform Model (using the AER line database), and a research platform, MRTA utilizing HITRAN 2012. Thus, we have three streams of data for the closure studies, and results of the comparisons are presented showing good agreement in the optically thick regions of 200-400 cm-1 and 600-800 cm-1. Differences between measured and coincident calculated spectra between 400 and 600 cm-1 are less than 10 mW/m^2/sr/cm-1. Uncertainties accounted for in this study include uncertainty from multiple detectors, water vapor, temperature, line strength and width as presented in HITRAN 2012, and due to internal heating caused by black bodies. The residuals fall within the root-sum-square envelope of the uncertainties.

J Mast↗

NASA NTRS2022

Improved representation of agricultural land use and crop management for large-scale hydrological impact simulation in Africa using SWAT+

To date, most regional and global hydrological models either ignore the representation of cropland or consider crop cultivation in a simplistic way or in abstract terms without any management practices. Yet, the water balance of cultivated areas is strongly influenced by applied management practices (e.g. planting, irrigation, fertilization, and harvesting). The SWAT+ (Soil and Water Assessment Tool) model represents agricultural land by default in a generic way, where the start of the cropping season is driven by accumulated heat units. However, this approach does not work for tropical and subtropical regions such as sub-Saharan Africa, where crop growth dynamics are mainly controlled by rainfall rather than temperature. In this study, we present an approach on how to incorporate crop phenology using decision tables and global datasets of rainfed and irrigated croplands with the associated cropping calendar and fertilizer applications in a regional SWAT+ model for northeastern Africa. We evaluate the influence of the crop phenology representation on simulations of leaf area index (LAI) and evapotranspiration (ET) using LAI remote sensing data from Copernicus Global Land Service (CGLS) and WaPOR (Water Productivity through Open access of Remotely sensed derived data) ET data, respectively. Results show that a representation of crop phenology using global datasets leads to improved temporal patterns of LAI and ET simulations, especially for regions with a single cropping cycle. However, for regions with multiple cropping seasons, global phenology datasets need to be complemented with local data or remote sensing data to capture additional cropping seasons. In addition, the improvement of the cropping season also helps to improve soil erosion estimates, as the timing of crop cover controls erosion rates in the model. With more realistic growing seasons, soil erosion is largely reduced for most agricultural hydrologic response units (HRUs), which can be considered as a move towards substantial improvements over previous estimates. We conclude that regional and global hydrological models can benefit from improved representations of crop phenology and the associated management practices. Future work regarding the incorporation of multiple cropping seasons in global phenology data is needed to better represent cropping cycles in areas where they occur using regional to global hydrological models.

crop phenology↗

NASA NTRSDate not supplied

Enhancing Radiative Transfer Models for Optimized Assimilation of Microwave and Radar Observations

Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.

Isaac Moradi↗

NASA NTRSDate not supplied

Optimizing Assimilation of Microwave and Radar Observations in the NWP Models

Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.

Isaac Moradi↗

NASA NTRSDate not supplied

Assimilation of Spaceborne Microwave and Radar Observations

Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.

Isaac Moradi↗

NASA NTRS2011

EPIC Radiance Simulator for Deep Space Climate ObserVatoRy (DSCOVR)

The Deep Space Climate ObserVatoRy (DSCOVR) is a planned space weather mission for the Sun and Earth observations from the Lagrangian L1 point. Onboard of DSCOVR is a multispectral imager EPIC designed for unique observations of the full illuminated disk of the Earth with high temporal and 10 km spatial resolution. Depending on latitude, EPIC will observe the same Earth surface area during the course of the day in a wide range of solar and view zenith angles in the backscattering view geometry with the scattering angle of 164-172 . To understand the information content of EPIC data for analysis of the Earth clouds, aerosols and surface properties, an EPIC radiance Simulator was developed covering the UV -VIS-NIR range including the oxygen A and B-bands (A=340, 388, 443, 555, 680, 779.5, 687.7, 763.3 nm). The Simulator uses ancillary data (surface pressure/height, NCEP wind speed) as well as MODIS-based geophysical fields such as spectral surface bidirectional reflectance, column water vapor, and properties of aerosols and clouds including optical depth, effective radius, phase and cloud top height. The original simulations are conducted at 1 km resolution using the look-up table approach and then are averaged to 10 km EPIC radiances. This talk will give an overview of the EPIC Simulator with analysis of results over the continental USA and northern Atlantic.

Lyapustin, Alexei↗

NASA NTRS2001

Assessment of the Contribution of the Atmosphere to Uncertainties in Normalized Water-Leaving Radiance: A Combined Modeling and Data Analysis Approach

Our research for the Sensor Intercomparison and Merger for Biological and Interdisciplinary Oceanic Studies (SIMBIOS) program has been focused on modeling and simulation studies as well as the development of atmospheric correction algorithms. Based on our original proposal and discussions at the SIMBIOS team meetings and workshops, the objectives of our research can be summarized as follows: (1) Use our radiative transfer model for the coupled atmosphere-ocean system to simulate the radiation field at arbitrary levels and in any desired direction in the atmosphere and ocean so as to provide a firm connection between the signal received by the satellite sensor and by a sensor looking down into the water column just above the surface and just below it; (2) Use the simulations to quantify the influence of atmospheric aerosols on the water-leaving radiance, and to quantify the error in the water-leaving radiance as a function of uncertainties in the aerosol optical properties, mass loading and vertical extent; (3) Use the model simulations in conjunction with validation measurements taken by other SIMBIOS investigators (for satellite overpasses) to assess our understanding of the radiative transfer process in the coupled atmosphere-ocean column, and to examine the extent to which the model provides a realistic prediction of simultaneously measured in situ water-leaving radiance and the radiance received by the satellite sensor; (4) Modify and improve an existing atmospheric correction algorithm, based on the work above, as needed by constructing new look-up tables that include scattering by ocean particles; and (5) Carry out approaches to developing an atmospheric correction algorithm for ocean color imagery with strongly absorbing aerosols.

Stamnes, Knut↗

NASA NTRS2003

Algorithms for Processing and Analysis of Ocean Color Satellite Data for Coastal Case 2 Waters

SeaWiFS has the ability to enhance our understanding of many oceanographic processes. However, its utility in the coastal zone has been limited by valid bio-optical algorithms and by the determination of accurate water reflectances, particularly in the blue bands (412-490 nm), which have a significant impact on the effectiveness of all bio-optical algorithms. We have made advances in three areas: algorithm development (Table 16.1), field data collection, and data applications.

Stumpf, Richard P.↗

NASA NTRS2012

Cleaning Genesis Mission Payload for Flight with Ultra-Pure Water and Assembly in ISO Class 4 Environment

Genesis mission to capture and return to Earth solar wind samples had very stringent contamination control requirements in order to distinguish the solar atoms from terrestrial ones. Genesis mission goals were to measure solar composition for most of the periodic table, so great care was taken to avoid particulate contamination. Since the number 1 and 2 science goals were to determine the oxygen and nitrogen isotopic composition, organic contamination was minimized by tightly controlling offgassing. The total amount of solar material captured in two years is about 400 micrograms spread across one sq m. The contamination limit requirement for each of C, N, and O was <1015 atoms/sq cm. For carbon, this is equivalent to 10 ng/cm2. Extreme vigilance was used in pre-paring Genesis collectors and cleaning hardware for flight. Surface contamination on polished silicon wafers, measured in Genesis laboratory is approximately 10 ng/sq cm.

Allton, Judith H.↗

NASA NTRS2003

Maximum Rates of Olivine Dissolution on Mars

This work is a first step in constraining olivine alteration rates on Mars. By bounding dissolution rates of olivine, we can make inferences about the temporal extent of aqueous alteration on the surface. Several hypothesized low-temperature surface aqueous alteration processes include valley network formation from release of groundwater during impact or gully formation from snow melt, both of which may occur over a period of several thousand years. Outflow channels may have formed during brief floods lasting less than a year. If large bodies of water were present during a warm, wet period, large standing bodies of water may have been present for 104 to 109 years. High-temperature alteration processes include hydrothermal activity associated with impacts and magmatic features. These features may remain active for 104 to 106 years. Table 2 summarizes speculated duration times of these aqueous processes. For comparison, we have determined minimum olivine residence times (time until complete dissolution) for 1 mm diameter particles to range from much less than one year to approximately 5,000 years.

J D Stopar↗

NASA NTRS1998

Observations of Total Lightning Associated with Severe Convection During the Wet Season in Central Florida

This paper will discuss findings of a collaborative lightning research project between National Aeronautics and Space Administration, the Massachusetts Institute of Technology and the National Weather Service office In Melbourne Florida. In August 1996, NWS/MLB received a workstation which incorporates data from the KMLB WSR-88D, Cloud to Ground (CG) stroke data from the National Lightning Detection Network (NLDN), and 3D volumetric lightning data collected from the Kennedy Space Centers' Lightning Detection And Ranging (LDAR) lightning system. The two primary objectives of this lightning workstation, called Lightning Imaging Sensor Data Applications Display (USDAD), are to: observe how total lightning relates to severe convective storm morphology over central Florida, and compare ground based total lightning data (LDAR) to a satellite based lightning detection system. This presentation will focus on objective #1. The LISDAD system continuously displays CG and total lighting activity overlaid on top of the KMLB composite reflectivity product. This allows forecasters to monitor total lightning activity associated with convective cells occurring over the central Florida peninsula and adjacent coastal waters. The LISDAD system also keeps track of the amount of total lightning data, and associated KMLB radar products with individual convective cells occurring over the region. By clicking on an individual cell, a history table displays flash rate information (CG and total lightning) in one minute increments, along with radar parameter trends (echo tops, maximum dBz and height of maximum dBz) every 5 minutes. This history table Is updated continuously, without user intervention, as long as the cell is identified. Reviewing data collected during the 1997 wet season (21 cases) revealed that storms which produced severe weather (hall greater or = 0.75 in. or wind damage) typically showed a rapid rise In total lightning prior to the onset of severe weather. On average, flash rate increases of 25 FPM per minute over a time scale of approximately 5 minutes were common. These pulse severe storms typically reached values of 150 to 200 FPM with some cells exceeding 400 FPM. One finding which could have a direct application to the warning process is that the rapid increase in lightning typically occurred in advance of the warning issuance time. Comparisons between the ending time of the rapid rate increase and the time of when the warning was issued by NWS/MLB meteorologist exhibited a lead time of 8 minutes. It is conceivable that if close monitoring of the LISDAD system by operational meteorologist is routinely performed, warnings for pulse severe storms could be issued up to 4 to 6 minutes earlier than what is issued currently.

Sharp, D.↗

NASA NTRS2004

Volcanic CO2 Abundance of Kilauea Plume Retrieved by Meand of AVIRIS Data

Absorbing the electromagnetic radiation in several regions of the solar spectrum, CO2 plays an important role in the Earth radiation budget since it produces the greenhouse effect. Many natural processes in the Earth s system add and remove carbon dioxide. Overall, measurements of atmospheric carbon dioxide at different sites around the world show an increased carbon dioxide concentration in the atmosphere. At Mauna Loa Observatory (Hawaii) the measured carbon dioxide increased from 315 to 365 ppm, in the period 1958 2000 [Keeling et al., 2001]. While at the large scale, the relationship between CO2 increase and global warming is established [IPCC, 1996], at the local scale, many studies are still needed to understand regional and local sources of carbon dioxide, such as volcanoes. The volcanic areas are particularly rich in carbon dioxide; this is due to magma degassing in the summit craters region of active volcanoes, and to the presence of fractures and active faults [Giammanco et al., 1998]. Several studies estimate a global flux of volcanic CO2 (34+/-24)10(exp 6) tons/day from effusive volcanic emissions, such as the tropospheric volcanic plume (Table 1) [McClelland et al., 1989]. Plumes are a turbulent mixture of gases, solid particles and liquid droplets, emitted continuously at high temperature from summit craters, fumarolic fields or during eruptive episodes. Inside the plume, water vapour represents 70 90% of the volcanic gases. The main gaseous components are CO2, SO2, HCl, H2, H2S, HF, CO, N2 and CH4. Other plume components are volcanic ash, aqueous and acid droplets and solid sulphur-derived particles [Sparks et al., 1997]. Volcanic gases and aerosols are evidences of volcanic activity [Spinetti et al., 2003] and they have important climatic and environmental effects [Fiocco et al., 1994]. For example, Etna volcano is one of the world s major volcanic gas sources [Allard et al., 1991]. New studies on volcanic gaseous emissions have pointed out that a variation of the gas ratio CO2/SO2 is related to eruptive episodes [Caltabiano et al., 1994]. However, measurements and monitoring of volcanic carbon dioxide are difficult and often hazardous, due to the high background presence of atmospheric CO2 and the inaccessibility of volcanic sites. Hyperspectral remote sensing is a suitable technique to overcome the difficulties of ground measurement. It permits a rapid, comprehensive view of volcanic plumes and their evolution over time, detection of all gases with absorption molecular lines within the sensor s multispectral range and, in general, measurement of all the volatile components evolving from craters. The molecular and particle plume components scatter and absorb incident solar radiation. The integral of the radiation difference composes the signal measured by the remote spectrometer. The inversion technique consists of retrieving the plume component concentrations, hence decomposing the signal into the different contributions. The accuracy of remote sensing techniques depends primarily on the sensor capability and sensitivity.

Spinetti, C.↗

NASA NTRSDate not supplied

Laboratory Investigation of the Effect of Venusian Weathering on Mineral Spectra

Introduction: The recent selection of two missions to Venus has renewed the importance of deter-mining weathering reactions between minerals and the Venusian atmosphere, and the spectral signatures of minerals before, during, and after these reactions. The rate at which weathering reactions progress also constrain show long unstable minerals will be present on the surface (e.g., [1]), and enables the use of mineralogy as a constraint on surface age(e.g., [2-3]).In order to gain an understanding of how mineral compositions and spectra change with weathering, we have begun conducting experiments in a 1 atm experimental setup at Wesleyan University. This setup exposes minerals to the temperature and most abundant gases of the Venus atmosphere (CO2, SO2, N2).We conducted initial experiments using biotite, calcite, and montmorillonite in order to test our methodology with minerals that may be relevant to recording the history of water on Venus. Methods: Experiments were conducted in Thermo Fisher Scientific Lindberg/Blue M Mini-Mite horizontal tube furnaces at Wesleyan University. Experiments used natural mineral chips and powders, and were conducted at 1 atmosphere and 460 °C under pre-mixed gases provided by Air Gas(Table 1). The furnaces are set up in a flow through configuration so that solid samples are exposed to a fixed gas composition, and quartz glass process tubes were used in all experiments (1/4” diameter for experiment V4, ½” diameter for all others). These conditions were maintained for the du-rations listed in Table 1, at which point the furnace was turned off with gas flowing until the sample was cool enough to extract under N2and be placed in a desiccator for storage. Run products were carbon coated and examined using a Hitachi SU5000 Field Emission Gun Scanning Electron Microscope (SEM) equipped with an EDAX Octane Pro EDS detector located at Wesley-an University. Visible-Near Infrared Spectroscopy (VNIR) analysis was performed on powdered samples under a nitrogen atmosphere using an ASD Fieldspec Proover the 350-2500 nm range. Powdered mineral samples were milled to a particle size of < 45μm and were spiked with an internal standard (Al2O3, corundum) to obtain quantitative mineralogy. Samples were analyzed using a Panalytical X’Pert pro X-ray Diffractometer (XRD), with an X’Celerator high speed detector and Co Kα radiation, with data collected at a step size of 0.02 ̊/minute step counting rate from 2 to 80 degrees 2θ at 45 mA/40kV in the X-ray Diffraction Laboratory located at NASA Johnson Space Center. Materials Data Inc (MDI) software suite, JadeTMv9 was used for Rietveld refinement to determine phase abundances and mineral identification by comparing XRD patterns to International Center for Diffraction Data (ICDD) database patterns. Table 1: Experimental matrix. Experiment Name Duration (Days)Gas Com-position (trace gas)MineralsV487SO2/N2(1.4%)Montmorillonite, biotiteV519SO2/N2(1.4%)CalciteV619CO2/SO2/N2(1.4% SO2, 2.1% N2)Montmorillonite, biotiteV828SO2/N2(1.4%)Biotite, calcite Results: Calcite. In both experiments, calcite was exposed to the SO2/N2gas mixture, and in both experimental run products, XRD analysis detected anhydrite, which is consistent with EDS measurements conducted in the SEM. The XRD analyses show greater amounts of anhydrite present after 28 days than 19, suggesting the calcite reaction progressed further given longer duration. Grain surface morphology as seen in the SEM also shows secondary mineral growth (Fig. 1). VNIR spectra show no change, as expected since anhydrite lacks spectral features in this wavelength range. Montmorillonite. Montmorillonite was exposed to two different gas mixtures, the SO2/N2mix and CO2/SO2/N2mix over different durations (87 and 19 days, respectively). VNIR analyses of both run products show a reduction in the 1441and1910 nm water features as well as a shift of the 1411 and 2011 nm features to shorter wavelengths that may indicate re-structuring in the crystal lattice and the production of amorphous phases [4]. XRD results are consistent with this, showing a shift of the 001 peak from 15Åto 10Åin both run products. The amount of X-ray amorphous material in the montmorillonite run products was greater than that present in the unreacted clay, being the greatest in the 87 day V4 experiment. No other secondary phases were detected in the run products, however sulfur was present in EDS analyses of powder samples.

A R Santos↗

NASA NTRS1973

Ecological effects of strip mining in Ohio

The author has identified the following significant results. One result significant as a practical application and for cost benefit analysis is the relative ease with which ERTS-1 will monitor new and unclaimed stripping activities in Southeastern Ohio and in all of Appalachia. Band 5 resolution appears to be better than the often reported 80 meters. The strip mines stand out well enough to be easily identified without other graphic aids. Standing water within the strip mined area stands out in either bands 6 or 7. Areas of several acres are visible. Significant increases in surface extent of water of stripped areas should be detectable on a comparative basis. The degree of reclamation is observable in the imagery in rather gross percentage steps and for areas larger than the bare earth sizes in the table. The gradation in tones in the different bands indicates that probability density imagery using the four bands in CCT data (and statistical processing) is likely to separate degrees of vegetative reclamation.

Chase, P. E.↗

NASA NTRS1987

Comets, volcanism, the salt rich regolith and cycling of volatiles on Mars

The composition of the Martian surface and its evolution are examined, reviewing the results of recent theoretical models and composition estimates based on Viking lander analyses. The data are compiled in tables and characterized in detail, and a high degree of variation among the predictions is noted. The discussion centers on the possible roles of comets (as sources of volatiles), the salt rich regolith (as an important water sink), and volcanic activity (interfering with volatile-recycling processes and eventually producing a volatile depleted surface layer).

Clark, Benton C.↗

NASA NTRS2022

Fire Island Water Resources: Assessing Sediment Dynamics and Turbidity Changes Along Fire Island National Seashore Using Satellite Data

Fire Island National Seashore has experienced damaging effects as a result of coastal erosion. Erosion has become an increasingly damaging problem that has led to the destruction of park and community infrastructure, contributed to rising groundwater tables, and posed a serious threat to a globally rare holly maritime forest. Beach nourishment project efforts have been made to mitigate damage, but dredging is expensive and can be thwarted by high rates of erosion. The NASA DEVELOP team partnered with the National Park Service and Fire Island National Seashore and used imagery from Landsat 5 Thematic Mapper (TM), Landsat 8 Operational Land Imager (OLI), and Sentinel-2 MultiSpectral Instrument (MSI) to analyze turbidity and sediment dynamics through surface reflectance data from 2000-2021. Imagery was atmospherically corrected using Atmospheric Correction for OLI Lite (ACOLITE) and visualized in SeaWiFS Data Analysis Systems (SeaDAS). Additionally, shoreline change was analyzed using high-resolution imagery from WorldView-2 acquired from Maxar for pre-Hurricane Sandy on July 25th, 2010 and post-Hurricane Sandy on December 18th, 2019. The results of this analysis showed that turbidity is highest in the winter seasons. The shoreline analysis estimated total shoreline loss of about 62 acres on the ocean side, and 11 acres on the bay side of the island. These results will be used to better inform future partner-designed shoreline management projects in the face of further erosion and sea level rise.

Kelly Young↗

NASA NTRS1978

Prototype residential solar-energy system

Complete solar-energy domestic-hot-water system for single-family residences is described in brochure. It contains data on procurement, installation, operation, and maintainance of system in residential or light commercial buildings. Appendix includes vendor brochures for major system components. Drawings, tables, and graphs complement text.

Source record↗

NASA NTRS1983

Spectral, spatial and radiometric factors in cover type discrimination

The influence of spatial, spectral, and radiometric resolutions on the utilization of Thematic Mapper (TM) and Multispectral Scanner (MSS) data is assessed quantitatively using a 2 x 2 x 2 factorial design experiment. Eight possible factor combinations were examined for agricultural, urban, forestry, range, and water types of land covers for three levels of information. Spectral bandwidths were configured to simulate all four Landsat MSS channels and Landsat TM channels 1, 2, 3, 4, and 7. By means of bar charts and tables it is shown that the 8-bit radiometric and 75-meter spatial resolutions provide a higher overall accuracy than the 6-bit radiometric and 25-meter spatial resolutions. Spectrally, the difference between the four MSS channels and five TM channel configurations is noted to be insignificant.

Alexander, D.↗